GE/PNH-43/2022-23

Amount

B&R PORTION:- Dismantling of timber scantling under 40sqcm and over in section unframed work,as in any position, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

Taking down shutters of area exc 1 sqm but not exc 2 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

Taking down shutters of area exc 2 Sqm each complete all as specified and directed.

Taking down chowkhat or frame exc 1.5 Sqm but n exc 4 Sqm each with shutters (without taking of shutter from the frames) complete all as specified and directed.

S&F 2nd class hard wood (kail) as in scantling clean sawn and fitted in unframed works, complete all as specified and directed.

S&F 2nd class hard wood (kail) as in scantling clean sawn and fitted in unframed works but except timber complete all as specified and directed.

M&L for cement concrete (1:2:4) using 20mm graded stone aggregate as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel work as in hand rails, half round or other stock section or core for wooden hand -rail, straight portion drilled and countrsunk for ballusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screqing etc. wind ties for roof including securing bolts, posts and struts in fencing including cuttings, tops to shapes, as directed, drilling, holes, notching for wire etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. fixed in repairs, and similar work conforming to Fe-250 Gde E-165 all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, valley gutter and similar works fixed with self tapping screws complete all as specified and directed.

S&F Mild steel, plain, black sheet 1mm thick in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. complete all as specified and directed.

S&F in repair 25mm thick, second class hard wood (Kail) boarding, planed one side, with butt joints and fixed with nails in flooring, facia and skirting etc complete all as specified and directed.

S&F 6mm thick plywood grade BWR type BB fixed with nails to timber frame work as in walls/ceiling, complete all as specified and directed.

S&F 2nd class soft wood (kail) as in scantling clean sawn and fitted in unframed works, complete all as specified and directed.

S&F 2nd class soft wood plain fillets, square, rectangular, or triangular in section, clean sawn, fixed with screws etc sectional area exc 3 Sqcm & n.exc 6 Sqcm etc, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/Rectagular) of size 400mm x 400mm, set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including cement screed bed 15 mm thick in cement mortar 1:6 base complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/Rectagular) of size 400mm x 400mm in vertical surface such as skirting, dados and risers set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar 1:4 base complete all as specified and directed.

M&L for glazed ceramic coloured/printed digital tiles, Premium quality of size 350x250x7mm/450x350x7 mm thick fixed as in vertical surfaces such as skirting, dados & repairs to step etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, fixed over and including 10mm thick plaster in CM (1:4), complete all as specified and as directed.

M&L for Vitrified coloured tiles 10 mm thick, premium quality (square/rectangular) area of each tile not less than 0.36 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and as directed.

All as per Item No 27 above but as in skirting/dados including 10mm thick screed bed in CM (1:4), complete all as specified and as directed.

M&L for 18-20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:6) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and and moulding the edges, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, including filled the joints with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base floors, complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in flooring and finishing fair, even and smooth without using extra cement, complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

M&L for walling of random rubble stone/boulder masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per Srl item No. 34 above but except stone complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:6 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

S&F plain, solid, 2nd class hard wood straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joint etc ,complete all as specified and as directed.

Cutting holes in stone walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples; chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) complete all as specified and directed by Engineer-in-Charge.

M&L for 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc, (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I, section 8, clause 8.24 (a) complete all as specified and directed.

M&L for 35mm thick 2nd class hardwood plain, framed, panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered paticle board medium density, wood patilcle board with commercial face veneers complete all as specified and directed.

M&L for 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc, (with sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I, section 8, clause 8.24 (a) complete all as specified and directed.

S&F Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square n exc. 0.5 Sq m each pane, complete all as specified and directed.

S&F mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F in repair mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled, 75mm long complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled, 100mm long complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F aluminium anodized barrel tower bolt of extruded section and fixed complete of size 150 mm long complete all as specified and directed.

S&F aluminium anodized barrel tower bolt of extruded section and fixed complete of size 75 mm long complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 150 mm and fixed, complete all as specified and directed.

S&F aluminium alloy handles, cast type, anodised of size 100 mm and fixed, complete all as specified and directed.

S&F 140mm long floor door stopper of aluminium alloy body and tongue with rubber stopper complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of OBD over & incl a coat of primer complete all as specified and directed.

Material & Labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces of walls complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer on new untreated wooden surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete all as specified and directed.

M&L for one coats of synthetic enamel paint on old wooden surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete all as specified and directed.

M&L for two coats of synthetic enamel painting on new steel surfaces over 10cms width or girth over a coat of red oxide primer etc complete all as specified and directed.

M&L for preparation of old plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of white wash complete all as specified and directed.

Taking up or down 15mm bore steel tubing & connection including cleaning for or removal from site 15mm complete all as specified and directed.

Taking up or down 20mm bore steel tubing & connection including cleaning for or removal from site 15mm complete all as specified and directed.

S&F GI tubing medium grade 15mm dia with all fittings, cutting, threading and fixing to walls,ceiling or in floors complete all as specified and directed.

S&F GI tubing medium grade 20mm dia with all fittings, cutting, threading and fixing to walls,ceiling or in floors complete all as specified and directed.

S&F in repairs 15 mm dia CP brass mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and directed. Make: Jaguar Cat No ARI-CHR-39051B or equivalent of Make as specified in PS.

S&F in repair 125mm dia PVC grating doom complete all as specified and directed.

S&F in repair stainless steel soap dish complete all as specified and directed.

S&F in repair bib taps 15mm bore of cast copper alloy, fancy type screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, fixed, complete all as specified and directed.

S&F in repair 15mm bore Stop valve cast copper alloy fancy type, CP with capston head, screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed, complete all as specified.

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (Semi-pedestal pattern), Anglo indian type white with seat cover incl all fittings including connection to drain and flushing pipe, antisyphonage pipe etc (excluding flushing cistern and flush pipe) complete all as specified

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets for low level cistern including all joints, complete all as specified and directed. Make:- Prayag cat part No 501 or equivalent cat part of make as specified in P.S.

S&F in repair Vitreous china wash hand basin, white, Oval size 630x450mm including brackets, brass chromium plated waste coupling, including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

S&F in repair flush pipe/waste pipe of polyethylene of low or high density of PVC, 32mm dia complete all as specified and directed.

S&F in repair towel rail 600mm long PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 190gm), complete all as specified and directed.

S&F in repair corner glass shelf consisting of 5.5 mm thick sheet glass of 12 cm wide with chromium plated bracket guard and railing 60 cm long fixed to wall with brass screws, complete all as specified and directed.

S&F in repair chromium plated brass Health faucet with 1m long easy flexible tube in chrome finish to connect with 15 mm dia pipe incl wall hook , complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in floor/walls as soil pipe including clamps, complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I, of capacity 500 Ltrs, complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I, of capacity 1000 Ltrs, complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and average 15cm deep and getting out in any type of soil, complete all as specified and directed.

Excavation in post holes each not exceeding 0.5 cum getting out, returning, filling in, including spreading, leveling, watering and well ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, in any type of soil, complete all as specified and directed.

M&L for cement concrete of type 1:3:6 type C2 (40 mm graded aggregate) as in post holes complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete, complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:2:4 (using 20mm graded crushed stone aggregate) type B-1 (Nominal mix) as in flooring, complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, shafts, wells, cesspits, manholes, pier holes, laying of pipes etc. n exc 10 sq m on plan and getting out in soft/loose soil complete all as specified and as directed.

Removal of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed.

Returning filling in including spreading levelling watering and well ramming in layers not exc. 25 cm thick each complete all as specified and directed.

M&L for rendering 20 mm thick on other than fair faces of brick or stone masonry wall surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of cement base paint complete all as specified and directed.

M&L for 200x200mmx25mm thick chequered cement concrete tiles set and jointed in neat cement slurry and pointed in white or coloured cement mixed with mixture of pigments to match with the colour of tiles laid over and including 20mm thick screed bed in CM (1:6), including demolition of existing floor tiles complete all as specified and as directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Taking down carefully unsv main switch / DBs alongwith MCBs any type / capacity and making good disturbed surface to match with the existing surface, complete all as specified and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following:-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

All as per srl item No 97 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F in repair ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC poly carbonate, insulated body, complete all as specified and directed.

S&F in repair switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F in repair switch socket combination 2 in 1, 5 pin, 6 Amp flush type universal), complete all as specified and directed.

S&F in repair switch socket combination 2 in 1, 3 pin, 6 & 16 Amp flush type universal, complete all as specified and directed.

S&F in repair socket outlet 2 in 1, 3 pin, 6 Amp flush type, complete all as specified and directed.

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

Supply and fixing Inverter LED batten 20 W with square profile and polycarbonate channel, lithium Ion battery with charging time 8 Hours-10 Hours and backup time upto 4 Hours with drive, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make - Havells Cat part No- LHEXACP7FN1W020 or equivalent of make as specified in PS.

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB SPN 40-63 amps, breaking capacity 10 KA, 'C' series complete all as specified and directed.

S&F in repair MCB single pole 6 to 32 amps, capacity 10 KA, 'C' series complete all as specified and directed.

Supply, laying and testing of cable in trenches/ poles XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 2 core 16 sqmm including taking down old cable complete all as specified and directed.

M&L for sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note: 1.Dry fine sand of best available quality shall be used. 2.Punned down thickness shall be made and paid.

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

S&F in replacement of GI pipe light grade 40 mm bore for cable protection fixed on poles or laid in trenches, under floor, ducts etc with fixing clamps, nuts bolts etc all as specified.

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F in repair LED 09 watt inverter lamp (B22 CDL), suitable for angle holder, complete all as specified and directed.

S & F in repair LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified directed.

M/S Krishna Enterprises

M/S KEWAL KRISHAN SANJEEV KUMAR VAID

M/S BHATT TRADERS