ADDITION ALTERATION AND SPECIAL REPAIRS TO KV SCHOOL GE NW MANKHURD

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Dismantling of brick work /stone bouldersbuilt in cement mortar including all quins, arches, pillars etc complete all as specified and as directed.

M&L for 15 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth complete all as specified and directed.

M& L rendering 10 mm thick ready mix plaster ceiling surface finished even & smooth with sagol finish complete all as specified and directed.

M&L for 20 mm thick(12+8mm) polymer modified ready mixed cement plaster including necessary scaffolding up to 24 m height complete all as specified and directed. ( NOTE :- WPC shall be measured and paid separately) .

Supply only integral water proofing compound complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete incl plastering (total thickness upto 60mm ) from RCC surfaces of columns, beams,Chajas, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note: Hard concrete shall not be removed by force.

M&L for cleaning existing reinforcement by sand blasting with suitable pump as directed by the GE and wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed . Note:- Mode of measurement: superficial area of concrete will be measured.

M&L for providing mild steel TMT bars in various structural RCC elements like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with binding wires etc. complete all as specified and directed. Note: This item is applicable for additional bars required in the existing RCC structures.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Monolith-PMM) OR Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

M&L for leakage / seepage proof coating consisting of preparing the new/old surfaces of existing exterior walls, parapet walls, chajjas etc. and applying Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions and all as specified & directed. Notes: (i) The aforesaid treatment shall be got executed by the contractor from the authorised applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE.

M&L for prepration of newly plaster/concrete surface of wall and applying two coat of distemper oil emulsion on walls with one coat of primer ( chalk white on plastered surfaces) and applying complete all as specified and directed

M& L for preparation of newly plastered surface of Ceiling and applying Three coat of white wash complete all as specified and directed

M & L for preparing old decorated surfaces of wall (plastered or unplastered or previously white washed ) & applying one coat of white wash complete all as specified and directed

M& L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed

M& L for complete removal of existing treatment on surfaces of walls and applying two coats of oil bound distemper over chalk whiting including 3 mm thick wall care putty applying on walls for smooth finish complete all as specified & directed .

M& L for complete removal of existing treatment on surfaces of walls and applying two coats of synthetic enamel paint over priming paints plaster coat applying on walls for smooth finish complete all as specified & directed

Demolition cement concrete (unreinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of stone slabs and tiles laid beded and pointed in any mortar of any description or thicknes in floors , aprons etc complete all as specified and directed.

S&F Vitrified light shade ceramic tiles 10 mm thick (square/rectanglar) polished area of each tile not exceeding 0.36 sqm ,in floors etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to matched laid over 15mm thick badding layer of CM 1:6 complete all as specified and as directed.

All as per items No 23 above but in skirting or in dado including 10 mm thick rendering CM 1:4 complete all as specified and directed.

M&L for coloured glazed ceramic tiles 300x200x6 to 7mm thick set and jointed in neat cement slurry and pointed with coloured cement as in skirting/dados including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as specified and directed.

M&L for non skid coloured ceramic tiles300x300x6 to7mm thick in floors etc set and jointed in neat cement slurry and pointed with coloured cement to match the shade complete including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed..

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick, with expansion joints & top surface finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for 75 mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in floor of sub base

M& L for Pre Polished Chequred cement concrete tiles 30cm x 30 cm x 20 mm thick, set, jointed and pointed in near cement slurry in floors with mixture of grey white cement in equal proportions over screed bed or bedding layer of morar 20 mm in cement mortar 1:6 complete all as specified and as directed

Dismantling boarding any description fixed in any position with nails complete all as specified and directed .

S & F for hot dipped GI imposed grid with 24mm wide T section exposed flanges powder coated frame work comprising of main runner made from 0.33 mm thick GS sheet of size 24mmx32mmx3000 mm @1200 mm C/C GI wire 4mm dia fixed by rawl plug,level adjusters and screws etc flush fitting of 1200mm long cross tee interlocked between main runners @ 600mm c/c to form 1200mmx600mm modules cross tee longer than 600 mm to be supported independently 600mmx600mm modules shall be formed by fitting 600mm long cross tee centrally between 1200mm cross tee ,perimeter wall angle shall be GS of size 19mmx19mm and 0.45 mm thick 300mm long including 600mmx600mmx8 to 10mm thick armstrong gypsum reinforced board with painting with two coat of plastic emulsion paint over primer complete all as specified.

S&F 18/19 mm thick prelaminated partcile board both sides , exterior grade , of approved shade and pattern fixid with screws to timber frame for cupboard and shelves and all necessary fittings ( hinges , scrowes , beeding piece haspstaple ), complete all as specified and directed.

Demolition of lime concrete or lean concrete from sunken floor including floor tiles, hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MOD land complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) in sunken portion, as per requirement complete all as specified and directed.

M&L for PCC 1:2:4, type-B, using 20mm graded stone aggregated as in sub base of floors and for any other propose in any location mixed with WPC @ 2% by weight of cement, complete all as specified and directed. Note: Supply only WPC will be measured and paid separately.

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fyber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid . (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

Taking up or down steel water tubing and connections of size 15mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 20mm bore, complete all as specified and directed.

Supply & fix 15mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fix 20mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F in repairs cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs bib taps, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated complete all as specified and directed.

S&F in repairs pillar taps; of cast copper alloy with capstan; head chromium plated screwed downend with pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe& fixed complete all as specified and directed.

S&F in repairs stop cock cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pip e or for brass chromium plated with fancy shank and cup(concealed type) complete all as specified and directed.

S&F in repairs CP grating doom 125mm dia of size complete all as specified and directed.

S&F in repairs chromium plated shower rose 125mm size with or without swivel joint for fixing in 15mm dia pipe complete all as specified and directed.

S&F in repairs corner wash basin vitreous china coloured size of 400x400 mm including GI brackets ,waste coupling ,and waste pipe cutting for and pinning in ends of brackets complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick as in flooring, treads, risers, landing etc over 15mm thick cement screed base CM 1;6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M & L for Makrna white Marble work 25mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following type including cutting and polishing, laid over and including 15 mm thick screed bedding layer in CM 1:4, complete all as specified and directed. Note: Marble to be provided as border of any type flooring as approved by Engr-in-Charge.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. over screed bed or bedding layer of morar 15 mm in cement mortar 1:4set and jointed in neat cement slurry and pointed in white or coloured cement to match Colour is approved by GE

M & L for Machine cut cudappah stoneslab 18-20mm thick over cementscreed base, laid and mixedwith pigment to match the shade of the slab window cills and jambs to full thickness of wall fixed in steps over cement screed bed 10mm thick in CM 1:4 and jointed with grey cement paste and slurry including rubbing and polishing complete all as specified and directed

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement in place of old one and re-fixing the same shuters in existing position etc, complete all as specified and directed

Dismantling cast iron or reinforced concrete drain pipes , water pipes (any size or pattern ) including all fittings, balance under credit ( measure overall as fixed along the centre line over fitting and accessories ) all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls all complete all as specified and directed.

All as per item no. 56 above, but 75mm bore complete all as specified and directed.

S&F Vitreous china squatting pan orrisa pattern of size 580 x 440mm with integral foot rest and 'P' or 'S' trap including lime concrete bedding connecting flushing pipe and taking out old WC pan & lime concrete and unserviceable connections and making good for floor etc complete all as specified and as directed.

Removing plant/growth including its roots upto 1.00m of plant height at any location/at any storey and of any description and treating the surfaces with Acid (HCL) and making good surfaces with cement mortar 1:4, complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal complete all as specified and directed.

All as per item No 60 above but 110 mm dia bend complete all as specified and directed.

S &F PVC (SWR) branch piece,single(single Y) 75mm bore equal or unequal complete all as specified and directed.

S &F PVC (SWR) bends, 75 mm bore, any radius complete all as specified and directed.

S &F PVC (SWR) junction single(single T), 110 mm bore, equal or unequal complete all as specified and directed.

S &F PVC (SWR) junction single(single T), 75 mm bore, equal or unequal complete all as specified and directed.

S &F PVC (SWR) branch piece,double( double Y) 75mm bore equal or unequal complete all as specified and directed.

S &F PVC (SWR) branch piece,double (double Y) 110 mm bore equal or unequal complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) Sqm but not exc 1.5 Sqm each including complete all as specified and directed.

Taking down shutter of any description but exceeding One Square Metre and not exceeding Two Square Metre each complete all as specified and as directed.

Taking down steel shutter of any description but exceeding One Square Metre and not exceeding Two Square Metre each complete all as specified and as directed.

S& F second class hard wood plain, solid straight chowkats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good disturbed surfaces of wall complete all as specified and directed

Refixing of shutter same opening exc 1.50 sqm not exc 4.00 sqm each complete all as specified and as directed.

S&F Factory made Plain framed, panelled shutters, 35 mm thick of second class hard wood (Hollock) (any numbers of panels) with panels of 12 mm thick veneered particle board exterior grade medium density with commercial veneering on both faces with sheesham wood beading all round the panel made out of 20 by 15 mm , on one side and fitted to chowkhats complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed. Make: SYNTEX/SHALIMAR/RAJSHRI

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F 100 mm long stainless steel butt hinges fixed with stainless screw complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 200 mm length complete all as specified and directed.

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised complete all as specified and directed.

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 250 mm complete all as specified and directed.

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-410-0 or Fe-310-0 all as specified & directed.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate etc including necessary form work complete all as specified and as directed.

M& L for preparation surfaces of new or previsouly untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M& L for preparation surfaces of old or previsouly treated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc, complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50m & making good surface complete all as specified and directed.

M&L Plain Cement Concrete Type B2 1:2:4 (using 40 mm graded stone aggregate) in foundations, filling and mass concreteand surrounding posts complete all as specified and directed.

S & F MS steel work in tubular trusses and tubular posts and square tubes including special shaped washers etc., complete using but welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and directed..Note: (structural desigen ,bent,shape,approval by GE)

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 gde E complete all as specified and directed.

S & F Stainless Steel railing, baulster, hand rail, pole with 304 grade with any dia, including cutting hole on any surfaces and fixing with cement mortar and araldite , complete all as specifed and directed. ( design , dia, bent,shape,approval by GE)

M & L two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of previously untreated surfaces of steel and iron exc 10 cm width or girth complete all as specified and directed.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Demolition of brick/cement concrete (unreinforced) / pcc tiles from existing roof/terrace etc and also removing/taking down of existing water proofing treatment of any thickness in any position including cleaning the surfaces of roof etc with wire brush complete and removing the retreived debris out side MD land, complete all as specified and directed.

Dismantling / taking out existing water proofing treatment (including cement screed bed below) from roof including loosened cement plaster and exposing the top surface of RCC slab and removing rubbish, etc. to a distance exceeding 500m and not exceeding 1.0km complete all as specified and as directed.

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof surface to achieve required slope, benching etc including making rounded or chamfered on edges mixed with WPC as per manufacturer's instructions, complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

M&L for screed bed 10 mm thick on brick work or concrete surfaces finished even and fair in cement plaster 1:4, complete all as specified and as directed with mixing water proofing compound.Note:( WPC shall be measured and paid separately)

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%.

M&L for applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane for non accessible roof complete all as specified and directed.

M&L Preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10 centimetre width or girth and applying Two coat of synthetic enamel paint complete all as specified and directed.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

Supply only 4mm thick plain transparent fibre glass sheet, ordinary quality fixed in aluminium window along F section all as specified and directed

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation etc and 10 Sqm on plan and not exc 1.5 metre in depth for pits indipendent holes etc, including getting out in any type of soil, complete all as specified and directed.

Returning, filling in with approved earth including spreading, leveling, watering and well ramming in layers n exc 25 cm thick, complete all as specified and directed.

Removing excavated material/soil to a distance not exc 50m and depositing where directed at a level not exceeding 1.5metre above the starting point , complete all as specified and directed.

M&L for reinforced concrete pipes, class NP - 2, 250 mm bore, laid and jointed complete with collars Complete all as specified and directed.

M&L for Pre-cast cement concrete cover slab for manhole and drain cover in plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4 with plain faces including demolition of existing Rcc cover complete all as specified and as directed.

M & L for Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built CM 1:4 complete all as specified and directed.

M&L for Plain Cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for Plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, drain complete all as specified and as directed.

M&L for Plain cement concrete 1:2:4 Type B-1 using 20mm graded stone aggregate as in benching, coping including necessary form work complete all as specified and as directed

S&F aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel including drilling as required in RCC sections in rectangular or architectual type balcony opening in existing building, complete all as specified and directed. Note: The Grills shall be of Model DG-100/DG-102 of Make Deco or equivalent make as approved by the GE.

M&L for applying two coat coats of component elastomeric acrylic polymer modified cementinious waterproofing coating , smart damp block 2K or approved equivalent , having 80% elongation as per ASTm D412, resisiting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.50. the mixing ratio of the coating shall be a 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc, complete as per manufactures specification

M&L Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along external wall where the apron is nor provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

M&L for At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ .5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed.

Taking out old unserviceable underground cable XLPE insulated, PVC sheathed armored heavy duty aluminum conductor LT 1100 Volts grade of size 4 Core 10 to 95 Sqmm 3.5 Core fixed on pole, wall and laid in trenches etc after disconnecting Note - Excavation and earth work will be mesured and paid seprately.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.50 mtr depth for laying of underground cable, erection of poles etc. and getting out in soft/loose soil including separating serviceable bricks for re-use at site obtained during excavation complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250mm x 150mm x 40mm laid in trenches complete all as specified and directed.

M & L for sand cushioning by spreading in trenches fine dry river sand by gently by punning down manually as in cable protection all as specified and as directed.

Supply & Lay XLPE insulated, armoured heavy duty 1100 volt grade electric LT UG cable ISI Marked with aluminium conductor of size 95 Sqmm 3.5 Core in trenches/along the wall/pole including making all connections complete as required at site and as directed by Engr-in-Charge -

All as per item no 125 above but of size 70 Sqmm 3.5 Core complete all as specified and directed.

All as per item no 125 above but of size 10 Sqmm 4 Core complete all as specified and directed.

Supply and fix in replacement of FRP looping box of size 250x200x100 mm with connector, MCB 6 Amps, Din Rail, GI clamps made out of GI flat of size 25mm X 3 mm channel including making connections all as specified and directed. Make - confirm to Cat No GSJB -2520 of Sintex/ National /Hensel.

M&L for Multistandarded Copper Conductor cable of 3 Core 1.5 Sq mm size for interconnection of cable looping box to Street Light Fitting complete all as specified and directed.

Dismantling of steel pole / struts of any size from various location and transporting to store for keeping in safe custody or for taking credit all as specified and directed.

Supply, Fixing and connection of hot dip galvanised octagonal poles of height 6 mtr with 130 mm bottom A/F & 70mm top A/F made up of 3mm thick HT sheet along with base plate of size 200 x 200 x 12mm thick including 4 nos of M20 x 600 long J type foundation bolts and 1 mtr long hot dip galvanised single arm standard bracket, including MCB of 6 Amps, with connector 4 way to be provided as termination point complete all as specified and directed.

M & L for TMT bars of Fe-500 D grade conforming to is:1786, 10 mm dia & over, including cutting to length, bent to shape equired, cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc, complete all as specified and directed.

M & L for TMT bars of Fe-500 D grade conforming to IS: 1786, 8 mm dia bars as in binders, spacers, strippus including cutting to length, bent to shape required, cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc, complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams , side and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter, for rough finished surfaces of concrete, complete all as specified and directed.

M&L for reinforced cement concrete nominal mix M-20 (using 20mm graded stone aggregate) for foundations, including rafts, footings, foundation beams, plinth beams, bases for column etc and mass concrete, complete all as specified and directed. (Note - Reinforcement and form work will be measured and paid separately).

M&L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying GI tube ;returning filling & well rammaing watering finish suraface 10 cm from top using PCC 1:3:6; including removal of surplus soil all as directed by Engr-in-Charge.

S&F of HDPE pipe 63 mm dia, PN-10 for laying in ground, road crossing etc for cable protection including necessary fittings, clamps for supports, etc all as specified and directed.

Supply and fix street light fittings LED type 60 Watts Watt complete with and including drivers, pressure die cast aluminium housing, prewired complete including taking down of old fitting complete all as specified and directed. The fitting shall conform to cat No-SZPSLPM060 of Shakti or Equivalent to Crompton /Philips/bajaj.

M&L for earthing using GI earthing strip 32 x 6mm complete with galvanised steel earth plate electode 600mmx600mmx6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level connection to and including GI strip of size 32x6mm to the extend 7.5 mtr as earth lead by means of GI bolts, Nuts etc. with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I including water arrangement with GI Pipe 20 MM dia (medium Grade), earth lead protection pipe 50mm madium grade with bends, elbow etc. from earth plate to test point, excavation and earth work returning, filling, ramming and removing of soil to distance not exc 50mtr, make good to match with existing surface making PCC pit (Earth chamber) having internal size 30cm x 30cm x 30cm and outer size 60cm x 60cm x 60cm with RCC reinforced cover 50mm thick with one lifting handle made of 8mm dia MS bar funnel wie mesh and testing on completion including making test point on wall as per SSR specification all as specified and directed.

M&L for earthing complete with copper earth plate electrode 600x 600x 3.15 mm buried directly in ground with top edge of the plate not less than 1.5 mtrs below normal ground level and connected to earth test point by means of copper Strip of size 20x3 mm all as specified and shown in electric plate No 3 of MES SSR Part-I including necessary excavation and earthwork, PCC chamber, CI cover, protection and watering pipe, funnel, mesh etc all as required at site and all as directed and including taking down of old earthing materials, complete all as specified and directed. Notes: (1). Cost for provision of 7.5 RM Copper strip and G I protection pipe 25mm bore, light grade sahll also deemed to be included in quoted rates. (2). Earth resistance of earth pit should be less than 0.5 Ohms. On testing, if the desired earth resistance is not obtained, the earthing will be redone at no extra cost. (3) Rate quoted by the tenderer shall also be deemed to include salt & Charcoal fillings upto & above 450 mm top of Copper plate.

M&L Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20x3 mm copper strip complete all as specified and directed.

Taking down copper/ aluminum point wiring (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, socket, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc.

Taking down of Old MCB DB of any size complete all as specified and directed.

Taking down of Old metal enclosure AC Socket with 20 Amps MCB complete all as specified and directed.

M & L for point wiring with PVC insulated unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC concealed conduit of suitable size and accessories, fixed on wall / ceiling etc with neccessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 2 mm thick pressed steel terminal boxes concealed in wall covered with laminated sheet top cover 3 mm thick for mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws all as specified for the following: (a) One light / fan / bell point controlled by one switch.

(b) All as per item No-146 One 5A 2pin/3pin socket out let multipurpose on the same board with other switches complete all as specified and directed.

(c) All as per item No-146 One 5A 2pin/3pin switch socket out let multipurpose on independent Board complete all as specified and directed.

All as per item No. 146 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board complete all as specified and directed.

Supply & Fix Bell push flush type 5 amp, 230 Volts complete all as specified and directed.

Supply & Fix switch piano single pole flush type 5A, 240 V one way complete all as specified and directed.

Supply & Fix switch socket combination 2 in 1 , 5 Amps multipurpose flush type complete all as specified and directed.

Supply & Fix switch socket combination 2 in 1, 3 pin, 5 and 15 Amps flush type universal complete all as specified and directed.

Supply & Fix Ceiling rose surface bakelite three terminal, 240 V complete all as specified and directed.

S&F fan regulator, electronic stepped (5 step), 230 volts, 100 watt, flush type and connecting-up, complete all as specified and directed.

Supply and fix bell ding dong AC 230 V single pole complete all as specified and directed.

Taking down carefully by unscrewing from boards/outlet boxes and refixing of same 5 Amps modular and piono switch,switch socket combination complete all as specified and directed.

Taking down carefully by unscrewing from boards/outlet boxes and refixing of same 15 Amps modular and piono switch,switch socket combination complete all as specified and directed.

S&F in repairs decorative recessed type LED light fitting 40 Watt (size '2x2') including driver, including provision of 3 core flexible copper cable 1.5 sqmm conductor wire for connecting from ceiling rose to connector, including making addition/altn to existing false ceiling shets aluminium frames including fixing arrangement complete all as specified and directed.Confirm to Cat No SZSBLMX040 of Shakti or equivalentto Bajaj/Cromton

S&F Channel/fitting batten for LED T8 tube rode CRCA Batten powder coated complete with all accessories suitable for T8 retrrofit tubes suitable for T8 batten double (2x20W T8 LED tube rode), 3 core 1.5 Sqmm cable for connection between ceiling rose & fitting and provision of 15mm dia GI pipe 3 feet for hanging complete all as specified and directed.The fitting shall conform to Confirm to Cat Ref SZSRFMX2X20 of Shakti or equivalent from philips/Bajaj.

S&F Channel/fitting batten for LED T8 tube rode CRCA Batten powder coated complete with all accessories suitable for T8 retrrofit tubes suitable for T8 batten single (1x20W T8 LED tube rode), scews , 3 core 1.5 Sqmm cable for connection between ceiling rose & fitting and provision of 15mm dia GI pipe 3 feet for hanging complete all as specified and directed.The fitting shall conform to Confirm to Cat Ref SZSRFMX1-20 of Shakti or equivalent from philips/Bajaj. Note: Serviceable LED Tube lights fitting deposite in KV Store for reuse

S&F LED T8 Retro LED tube rod 20 Watts, 230 volts, LED retrofit solution for T8 FTL tube light with LED rod of aluminium extruxted housing, opaque diffuser for optimum and glare light output, the rod shall conform to Cat No SZFRTMX020 of Shakti or Equivalent from Philips/Bajaj complete all as specified and directed.

Taking down ceiling fan/exhaust fan, sealing cable end dismantling blades and removing fan and blades and keeping in safe custody for refixing if found serviceable or issuing under credit complete all as specified and directed. Note: Serviceable Ceiling fans and Exhaust fans to be deposite to KV School

Re-fixing only ceiling fan 1200mm sweep including provision of cable from ceiling rose/ conductor to fan and spray painting of ceiling fan with two coats of synthetic enamel paint, after preparation of surfaces, complete all as specified and directed.

Supply & Fix ceiling fan complete with down rod and acessories 230 V, 1200 mm sweep all as specified and directed by Engineer –in –Charge. confirm to Kassels 50 ISI Code 250467* of Bajaj or equivalent Havells/Orient.

Re-fixing only exhaust fan upto 450 mm including provision of cable from ceiling rose/ conductor to fan and spray painting of ceiling fan with two coats of synthetic enamel paint, after preparation of surfaces, complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers all as specified and directed by Engineer –in –Charge. confirm to FRESHEE MK II Code 70003 of Bajaj or equivalent Havells/Orient.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep with, blades, and frame and louvers all as specified and directed by Engineer –in –Charge. confirm to SUPREME PLUS Code 70064 of Bajaj or equivalent Havells/Orient. Note: Serviceable Exhaust Fans deposite in KV Store for reuse

M & L for Cutting holes into or through brick walls built in cement mortar for fixing the Exhaust fan and making good the distrubed surfaces in cement mortar 1:3 complete all as specified and directed.

Supply And Fix IP: 43 Protection MCCB DB TPN 4 Way double door prewired suitable for Triple Pole 125 A MCCB as incomer and provision of the following acessories:- a) MCCB TP 125 A 16 KA 415 Volt - 1 Nos b) Bus bar, Din rail , Neutral link c) including cutting chassis in wall and concealing in wall & making good the surface CM to match with the existing surface. The DB Shall Conform to Cat No - 811888 Optium F 1 + 12 of Indo Asian or Equivalent from Stanrad/Havells Location : Adm Bldg Ground Floor KV School

Supply And Fix IP: 43 Protection MCCB DB TPN 4 Way double door prewired suitable for Triple Pole 100 A MCCB as incomer and Provision of the following acessories, a) MCCB TP 100 A 16 KA 415 Volt - 1 Nos b) Bus bar, Din rail , Neutral link c) including cutting chassis in wall and concealing in wall & making good the surface CM to match with the existing surface. The DB Shall Conform to Cat No - 811888 Optium F 1 + 12 of Indo Asian or Equivalent from Stanrad/Havells Location: Primary and Secondary Bldg Ground Floor KV School

Supply And Fix IP: 43 Protection MCB DB TPN 4 Way double door prewired suitable for Triple Pole 63 A MCB as incomer and provision of the following acessories, a) MCB TP 63 A 16 KA 415 Volt - 1 Nos b) Bus bar, Din rail , Neutral link The DB Shall Conform to Cat No -811870 and module 8 + 12 of Indo Asian or Equivalent from Standared/Havells Location : First & Second Floor KV School

Supply & Fix MCB DB Double Door SPN 12 way 240 volts all as specified and directed.

Supply & Fix MCB DB Double Door SPN 8 way 240 volts all as specified and directed.

Supply & Fix MCB DB Double Door SPN 4 way 240 volts all as specified and directed.

M&L for MCB SP, 240 volt, 6 to 32 Amps, 10 KA all as specified and directed.

M&L for MCB SPN, 240 volt, 40 Amps, 10 KA all as specified and directed.

M&L for MCB TPN, 415 volt, 40 Amps, 10 KA all as specified and directed.

M&L for MCB TPN, 415 volt, 63 Amps, 10 KA all as specified and directed.

M&L for sub main wiring with two run single core 4.0 Sqmm PVC insulated FR multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including one run PVC insulated 4.0 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed including taking down of old sub main wiring Note : 1 Two Run of 4.0 Sqmm Wire, one run of earth wire PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two run single core 6.0 Sqmm PVC insulated FR multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including one run PVC insulated 6.0 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed including taking down of old sub main wiring Note : 1 Two Run of 6.0 Sqmm Wire, one run of earth wire PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with two run single core 10.0 Sqmm PVC insulated FR multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including one run PVC insulated 10.0 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed including taking down of old sub main wiring Note : 1 Two Run of 10.0 Sqmm Wire, one run of earth wire PVC casing capping will be measured and paid one unit.

M&L for sub main wiring with four single core 16.0 Sqmm PVC insulated FR multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including one run PVC insulated 16.0 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed including taking down of old sub main wiring. (TPN DB to Floor TPN DB) Note : 1 Four Run of 16.0 Sqmm Wire, Two run of earth wire PVC casing capping will be measured and paid one unit.

Supply and fix in earthed metal clad socket outlet with earthed plug top 20 Amps capacity with sheet metal enclosure and one 20 Amps MCB SP all as specified and directed.

mp construction co

Joy builders

Parmatma Enterprises

Nexus Infratech

ORIENT ELECTRIC CO

Garima Construction Co

S R INFRASTRUCTURE

Modern Engineering Co

AGRAWAL ASSOCIATES