RENOVATION OF ROOM NO 225 OF BLDG NO P-96 AT SUBROTO PARK PROVN OF RCC MS IRON STEPS/STAIRS AND RAMP WITH MISC WORKS IN LOBBY/CORRIDOR OF AFRO BLG AT SUBROTO PARK AND PROVN OF HEAVY DUTY WALL MOUNTED FANS ALONGWITH LED (2x2) ENERGY EFFICIENT LIGHTS

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge

M&L for Vitrified ceramic coloured (dark/light shade) tiles (600x600)x9/10mm thick in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in cement mortor 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in cement mortar 1:6 complete all as specifed and directed.

M&L for PCC 1:2:4 type B-0 (Using 12.5 mm graded stone aggregates) of 25 mm thick as in leveling course ,finished surfaces even and rough to receive floor finish complete all as specifed and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 7mm/450 x 350 x 7mm thick over and ncluding 10 mm thick rendering in cement mortar 1:4 as in backing coat for tiles on vertical surfaces,set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed and directed.

M&L for Vitrified coloured tiles (600x600)x9/10mm thick in skirting etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick plastering in CM 1:4 as in backing coat of tiles complete all as specifed and directed.

M&L for pvc tiles/ sheets laminates, plain coloured, marbled mosaic, or mottled finish or wooden flooring sheets finish of thickness minimum 2 mm laid with approved rubber based adhesive in floors complete all as specified and directed by engineer in charge.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed by the Engineer-in-Charge.

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets/board fixed in aluminium door or partition, any thickness, including cover fillets & framed work if necessary complete all as specified and directed.

S & F false ceiling at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of Size 595x595 mm, semi perforated 12mm thick micro regular edged of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 476 (part 4) - 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross - T of size 15x32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

S & F 'E' board(Design: LACK & hill) : 605x605x4 mm thick, white pre laminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanized iron imposed grid with 24 mm wide T-section exposed flanges which shall be power coated white. The frame work shall be comprise of main runner made from 0.33 mm thickgalvanised steel sheet and of size 24 mm X32mmX300 mm board spaced at 120 mm maximum center to center, hangers of GI wire4 mm dia to be fixed by approved rawal plug level and fasteners and screws etc.,The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall , flushing fitting of 1200 mm longer cross tee(with double stitching) to be interlocked between main runners at 600 mm center to center from 1200X600 mm modules cross tee longer than 600 mm to be supported independently . 600mm long cross tee centrally between the 1200 mm cross tee(with double stitching) to be interlocked between main runners at 600 mm center to center from 1200X600 mm modules cross Tee longer than 600 mm to be supported independently . The perimeter wall angle shall be 0.45 mm thick GS sheet of size 19 mm X 19 mm and 300 mm long of white colour all as per manufacturer's instructions complete all as specified and directed by Engr-In-Charge.

S&F 5mm thick ACP wall cladding sheet in colour as directed by Engr-in-charge fixed on MS frame . The size of each panel not exc 1.5sqm. MS frame to be fixed on walls, chajja and fasad with Min 08 Nos GI fastener 5" long per 1.5 sqm, including all necessary repairing work as reqd, two coat of synthetic enamel paint over one coat of red oxide primer, including weather sealing sealent, masking tape, including cutting of V groves to fixing moulded ACP sheet self-tapping screw complete all as specified and directed by Engineer-in-Charge. Note 1. MS frame should be fixed on wall after painting.

M&L for PVC profile for wall paneling of size 23cm wide, 8mm over all thick and 01mm wall thickness fixed with screw to mild square tubular steel frame work mad e out of MS Hollow section of size 25mm x 15mm x 2mm spacing 01 meter on both side frame work shall be fixed in wall with the help rawl plug and required length of screws and MS work shall painted with one coat of Red oxide primer for wall panelling,complete all as specified and directed by Engr-In-Charge.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5 Sqm but n exc 4 Sqm each,incl removing complete all as specified and directed by Engr-In-Charge.

Taking down chowkats or frames with shutters (with out taking of shutter from the frame) not exc 1.5 sqm each complete all as specifed and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners not paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid Moulded decorative flush door shutter of 35mm size comprising of virgin polymer of K value 58-60(Suspension Grade), 2, 4, or 6 raised panel design calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus ofelasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F brass 150mm , barrel tower bolts extruded section.complete all as specified and directed by Engr-In-Charge.

S&F for Butt hinges of brass 100mm size, Heavy grade, complete all as specified and directed by Engr-In-Charge.

S&F for Brass Mortice lock, vertical type, size 100mm 4 levers vertical complete all as specified and as directed by the Engineer-in-Charge

S&F brass finish ISI marked magic eye complete all as specified and directed by Engr-In-Charge.

S&F for door closer hydraulically regulated brass (dia cast) body, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg, fixed as in repairs, complete all as specified and directed.

S&F vertical venetian blinds made out of nylon cloth of any clour 100mm wide strip as aprroved including hanging arrangement rollers etc complete all as specified and directed by Engr-in-Charge.

S&F 150mm long extruded brass fancy handles fabricated type complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement of cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc complete all as specified and as directed by the Engineer-in-Charge

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (Cement plaster 1:6) finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge

M&L for 5 mm thick rendering in cement mortar 1:3 on fair faces of ceiling or cement concrete surfaces finished even and smooth without using extra cement complete all as specifed and directed.

M&L for providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for complete removing existing treatment new/old surface of wall and applying two coat distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer by EIC, of required shade and colour over applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth. complete, as per manufacturer's specification. complete all as specified and as directed by Engineer-in-Charge.

S&F decorative laminate type 1 of surface finish , colour, and pattern as approved of thickness 1.5mm , fixed with approved adhesive as per manufacturers instructions complete all as specified and as directed by Engineer-in-Charge.

S&F 12mm thich Toughned glass as in hinged doors, partitions, sliding doors, automatic doors and similar work of approved brand and manufactures, including cutting to shape, drilling holes required, including Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed by Engr-in-Charge. Note:- Rate included all nessesry fitting and frame work for glass fitting, provision of top and bottom pivots, S/S handle, hinges, double action floor spring, stoppers etc. complete all as specified and directed by Engr-in-Charge.

S&F solar control film 50 micron thick reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engr-in-Charge.

M&L for powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Supply and fixing 4.8 mm thick ordianary quality sheet glass exe 0.5 sqm in each pane of glazing with oil putty /beading etc all as specified and directed by Engineer-in-Charge.

S&F for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders;Chajjas, framed balusters; walk ways; railings; cooler stand, stair, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed

M&L for Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges and similar works for flat rough finished surfaces of concrete complete all as specified and directed.

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9mm dia upto four storey complete all as specified and directed

M&L for Reinforced cement concrete (nominal mix) 1:2:4, type B-1 using (20mm graded aggreate) in slabs supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slabs and in chajjas/ shelves and the like complete all as specified and directed

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 M mean radius built in CM 1:4 complete all as specified and directed

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundations filling and mass concrete complete all as specified and directed

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, cladding and like in cement mortar (1:4) including pointing in white cement (1:2) us in granite dust with admix ture of pigment to match with shade of granite and including 15 mm Screed bed or bedding layer or backing coat of CM 1:4 complete all as specified and directed

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified and directed

M&L for preparation to old surfaces of walls and applying two coats of oil bound distemper, oil emulsion on old wall surfaces over a coat of wall care putty and over a coat of primer complete all as specified and directed.

Taking down carefully copper/aluminium point wiring light ,fan, light fittings,socket or power complete, such as switches, ceiling roses, pendents, regulators, sockets etc.removing materials to store for keeping in safe costudy or for taking credit (credit for above items should be made as per conditioned separately) and making good disturbed surface of walls, floors etc. complete all as specified and directed by Engineer-in-Charge.

M&L for Point wiring For one light point controlled by one SP switch using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed stranded cable 1100 volts grade (FRLS),ISI-694 marked in and including heavy duty, PVC concealed conduit after cutting,chasing the wall etc and making good of disturbed surface, including all accessories etc, heavy duty ISI marked, including mild steel sunken boxes with earth dolly duly powder coated suitable for modulater plates of required size, covered with modular plates, suitable for modular switches, sockets etc including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) (FRLS) single core cable as earth continuity conductor to common earth and connecting to earth dolly. ( Note- Modular Switch and sockets will be measured and paid seperately).

All as per item No 47 here in before but For one fan/exhaust fan and wall mounted fan point controlled by one SP switch.

All as per item No 47 here in before but For one bell point controlled by one No bell push

All as per item No 47 here in before but for one 3 pin socket out let, 6 Amps on same board

All as per item No 47 here in before but for one 3 pin socket out let, 6 Amps on Independent board

All as per item No 47 here in before but with 2.5 Sq mm cable for Independent board one 3 pin 15 Amps socket outlet including Single core 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FRLS cable for continuous earth wire 2.5 sqmm FRLS all as specified and directed by Engineer-in-Charge. ( Only one 15 Amp point will be in one circuit)

S & F Modular switch 1 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 6A - 3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S&F Modular switch 1 way 16A, 1 modules suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 16A - 3/5 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

Supply and fix electronic modular Fan Regulator rotary flush step type 120 watt, 240 volt Complete all as specified and directed

Supply and fix bell Modular push flush type 5 Amps suitable for 240 volt Complete all as specified and directed

Supply and fixing ding dong bell AC 230 volt single pole complete all as specified and directed

Supply and fixing of ceiling roses, surface bakelite 65x50mm 2 or 3 terminals , PVC/Polycarbonate, isolated body fixed on PVC round block complete all as specified and directed by Engineer-In- Charge.

Taking down old unsv MCCB/MCB DB of any size Complete all as specified and directed

Supply and fixing MCB distribution board with Bus bar 200A neutral link ,earth bar made out of CRCA mild steel sheet surface mounting SPN 12 way 230 volts double door type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.

Supply and fixing load line vertical distribution board made out of CRCA sheet,double door, surface mounting TPN 4 way 415 volts 200 Amps rated bus bar and stove enamels dust and vermin proof suitable for TP/FP incomer MCCB of 160 Amps complete all as specified and as directed by Engineer-in-Charge. Note :- MCB and MCCB shall be measured and paid seperately.

Supply and fix in replacement of fixed adjustable type, 3 pole MCCB 160 Amps, 50 HZ,Ics=100%Icu, 415 volts with rupturing capacity 36 KA complete all as specified and directed by Engineer-in-charge.

S&F in replacement MCB SP 6 to 32 Amps 10 KA, 240 volt 'C' Series all as specified and directed by engineer-in-charge.

S&F in replacement MCB SPN 32 Amps 10 KA, 240 volt 50 HZ 'C' Series all as specified and directed by engineer-in-charge.

S&F in replacement MCB TP 25 to 63 AMP 10 KA, 240 volt 50 HZ 'C' Series all as specified and directed by engineer-in-charge.

S&F 3 pin plug top 15 Amps all as specified and directed by engineer-in-charge.

Taking down of light fittings of any wattage complete all as specified and directed.

Supply and fixing warm white LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specifed and directed .

S&F focus light round shape LED 10 watt 220 volts AC with high efficiency PMMA diffuser suitable for roof ceiling/wall including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable submain wiring of alluminium two/three/four runs of any size cable including batten/conduit complete etc and making good disturbed surfaces complete all as specified and complete all as specified and directed by Engr-in-Charge.

M & L for submain wiring with three run of 4.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked through suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all concealed in wall and surface conduit on ceiling, complete all as specified .( Note : 3 runs of cable and one run conduit will measured one unit for payment purpose.

All as per item No 74 above but size of wire 10.0 sq. mm

Supply and fix White cover plate with frame,1 module Complete all as specified and directed by Engineer-in-Charge.

Supply and fix White cover plate with frame,2 module Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Metal flush box 1 module Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Metal flush box 2 module Complete all as specified and directed by Engineer-in-Charge.

S & F Modular Socket, 32A - 3/5 pin 2 module, suitable for 240 volt AC Complete all as specified and directed by Engineer-in-Charge.

S&F Modular MCB SP 25 Amps 10 KA, 240 volt 1 module all as specified and directed by Engineer-in-charge.

Taking down including disconnecting the electric connection of exhaust fan and dismantling blades,greasing and painting the whole assembly complete all as specified and directed by Engr-in-Charge.

Fixing only Exhaust fan received from item No 81 above and connecting up including fastner and provision of suitable size of copper cable from connector of fans to ceiling rose complete all as specified and directed by Engr-in-Charge.

Dismantling including disconnecting the electric connection for split AC 1.5/ 2.0 TR indoor and outdoor unit and to be kept in safe custody for refixing complete all as specified and directed

Servicing,Installation,connecting of Split AC 1.5/2.0 TR received from BOQ item No 83 including gas charging if required and testing upto satisfaction of Engineer in charge Complete all as specified and directed. Note: Gas charging and minor parts replacement required at site also included in the unit quote rate of item.

S&F in replacement refrigerant line copper tube1/2" bore incl insulation of AC pipe complete all as specified and directed.

S&F in replacement refrigerant line copper tube 1/4" bore incl insulation of AC pipe complete all as specified and directed.

Supply & Fixing in replacement of PVC pipe of size 20 mm dia fixing on wall by using clamps and screwing including necessary tee, collar ,bend,socket etc complete all as specified and directed.

Supply & Fixing in replacement of flexible thredded from indoor unit to main line size of 15/20 mm dia , fixing on wall by using clamps and screwing complete all as specified and directed.

M&L for point wiring for One C/ fan/Exhaust fan/wall fan point controlled by one switch one way with single core PVC insulated unsheathed 1100 volt grade cable with multi strand copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through and including non metallic rigid PVC conduit, medium grade, ISI marked not less than 20 mm dia, concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and provision of pressed steel terminal modular box powder coated of suitable size for mounting piano switch sockets and regulators and drawing continuous earth wire of PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) For one light point controlled by one SP switch complete all as specified. Note: Cost for cutting, chasing and making good to existing surfaces are deemed to be included in the Quoted Rate.

All as per item No 89 here in before but One light point controlled by one switch one way.

Supply & fix Switch Piano, Flush Button, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

Supply & fix socket outlet 2in1, 3 pin 5 Amps flush type suitable for 240V AC Complete all as specified and directed by Engineer-in-Charge.

S&F wall mounting fan (air circulator metal body) 450 mm sweep, 230 Volts, 100 Watt, 150 CMM, noice level 60 to 65 db turboforce air circulator wall fan motor speed not more than 1400 RPM 3 blade and mechanism for upwad and downword adjustment including necessary fixing arrangement for proper fixing in wall as per site requirement complete all as specified make almonard or equivalent .

Supply and fixing 18 watt LED slim recess panel light , 210mm, white color with high efficiency PMMA diffuser soft glare free light complete with driver, holders suitable for roof all as specified and directed at site.

Supply and fixing 415V 10KA 'C' curve TPN 16 To 32 AMP miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately.

S&F MCB SPN 40 Amps 10 KA, 240 volt 50 Hz 'C' Series all as specified and directed by engineer-in-charge.

M/S MG GROUP (BID ID -3367858)