SPL REPAIR TO BLDG NO P69 AND P120 AND ALLIED WKS AND PROVN OF CAR PARKING AND ALLIED INFRA NEAR OFFICE COMPLEX AT HQ NORTHERN COMMAND AND RENOVATION OF FOUNTAIN TILING AND ALLIED WKS AT DHRUVA WAR MEMORIAL UNDER GE SOUTH UDHAMPUR

Amount

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sqm on plan and getting out in any type of soil, complete all as specified and as directed.

Excavating in post holes (or similar holes ) each n. exc 0.5 cum in soft /loose soil getting out, returning filling in and ramming around in layers not exceeding 25 cm complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil, complete all as specified and as directed.

Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Taking down frames with shutters (without taking off shutters from the frame ) area not exc 1.5 Sqm each incl iron mongry complete all as directed.

Taking down frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each incl iron mongry complete all as directed.

Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar any description complete all as specified and as directed

Dismantling of cast iron or reinforced concrete drain pipe/PVC pipe 100/110 mm dia and below jointed in cement mortar and taking out of floor/walls etc complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Demolition of cement concrete any description and any position not otherwise specifically provided complete all as specified and as directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M&L for 75 mm thick PCC type CI 1:3:6 using 20mm graded crushed stone aggregate as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 50 mm thick PCC 1:4:8, type D-2 by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M & L for PCC 1:2:4 Type B2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L PCC 1:2:4 type B0 (12.5mm graded aggregate) as in coping, benching, edging of pathway and similar work etc including necessary form work complete all as spcified and directed.

M&L for plain cement concrete1:2:4 type B-2 using 40 mm graded stone aggregate as in channels and drains, foundation and similar work etc complete all as specified and as directed.

M&L Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate ) for manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and as directed.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1(20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n.exc. 50m from the starting point, complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM (1:4) as in drain, walls and similar work etc complete all as specified and as directed.

M&L brick work with subclass B bricks, straight or curved on plan exc 6m mean redius built in CM 1:6 complete all as specified and as directed

M&L Hardcore of broken bricks gauge n exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rolled /rammed to true surfaces complete all as specified and as directed.

Rendering 15mm thick in CM 1:4 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and as directed

Rendering 10mm thick in CM 1:6 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and as directed

M & L for rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces as on ceiling complete all as specified and as directed.

M&L 1mm thick wall care putty on wall complete all as specified and as directed

M & L for preparation of new plaster surfaces of walls/ceiling and applying two coats of oil emulsion distemper (white/tinted) complete all as specified and as directed.

M&L for vitrified tiles (Double charge glossy finish), area of each tile exc 0.42sqm but not exc 1.00 Sqm, 8-10mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Ditto as per item No above but in vertical surfaces such as skirting/dado and including 10mm thick rendering as back coating etc complete all as specified.

M & L for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for Glazed Coloured Ceramic tiles in vertical surface 300x600x7mm thick laid over 10 mm thick screed bed in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

M & L 18-20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed.

S&F Vitrified Dura stone pathway tiles of size not exc 0.36 Sqm of 8-10mm thick as in floors and over & including 15mm thick screed bed or bedding layer in cement mortar 1:6 including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles, complete all as specified and directed

M&L for coloured chequered cement concrete tiles 30cmx30cmx25mm, machine pressed; set jointed and pointed in neat cement slurry in floors, with grey cement and pigments laid over 15 mm thick screed be in CM 1:6 complete all as specified and as directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi?chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

M & L for sheet glass 5.5mm thick of one side view, ordinary quality and glazing with beads fixed with metal panel pins, EPDM washers or connected accessories exc 0.5 sqm in each pane complete all as specified and as directed

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F 4 mm dia galvanised steel wire 50 mm x 50 mm mesh made up in to matresses or cages etc all as specified and as directed.

M&L for preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Eco cell or equivalent make

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type wire mesh solid door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). Make : Eco cell or equivalent make

Supply and fixing factory made uPVC white/coloured fixed glazed window/ventilator/Partition walls made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).

M&L for 25-30 mm Thick Polymer modified fiber reinforced ready mix mortar in screed bed using guniting process for laying floor and wall finishes of swimming pool mosaic tiles in single layer concrete surfaces including making groove of appropriate size, on other than fair faces of concrete/brick surfaces (internal surface) and finished even & smooth witjhout using extra cement, complete all as specified and as directed by Engineer-in-Charge.

Under tile water proofing membrare in two layers and over screed bed floor and wall finishes of swimming pool mosaic tiles complete all as specified and as directed by Engineer-in-charge. Make : WPM 002 of Adrex Endura or Dr. Fixit Fastflex or equivalent as approved by Engineer-in-Charge.

S&F for stainless steel sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S & F 150mm long stainless steel barrel tower bolts of extruded section complete all as specified and as directed.

S&F butt hinge 100mm size, medium weight, cold rolled mild steel complete all as specified and as directed.

S & F 150mm stainless steel handles, oval type complete all as specified and as directed.

S & F 150mm double action spring hinges, mild steel with steel wire spring, stove enamelled, black complete all as specified and as directed.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm complete all as specified and as directed.

M&L for cupboard/almirah in required size at site made out 18 mm thick one side decorative lamination sheet/sunmica consisting of carcass 18/20 mm thick PVC sheet & provn of shutters made out of 18mm thick one side decoartive laminated PVC sheet all reqrired brackets SS screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edbes shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work complete as per make and specification mention as per drawing with locking arragement approved by Engr-in-Charge (Make: Rajshree/Sintex/Action Tessa or equivalent) Complete all as directed.

S&F PVC steel catcher of superior quality all as specified and directed by Engr in charge

S&F Hetich softcloser hinges of stainless steel premium quality complete all as specified and as directed.

S&F Fancy type Brass handles 100mm size fixed with screws, complete all as specified and as directed.

S&F 20mm dia mild steel powder coated fancy type tubular curtain rail with brackets and end bulb as per reqirement. all as directed.

S&F blow moulded rotational moulded polyethene water storage tank 1000 ltr capacity hoisted and fixed in position having 20mm dia PVC float valve and tank nipple, including dismantling of existing tank, complete all as specified and as directed.

S&F in repairs gun metal globe or gate valve 20mm , with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down old tubing, complete all as specified and as directed.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs including taking down old tubing, complete all as specified and as directed.

S&F in repairs PVC connection 15 mm size with PTMT nuts 600mm long, fixed in repairs, complete all as specified and as directed.

S&F in repair countertop vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including provision of pair of mild steel angle iron brackets of suitable size duly painted, 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete. Make : Jaquar Make :KUS-WHT-35601 or its equivalent in Hindware/Cera/Parryware

S&F in repairs 5 mm thick looking mirror of required size, fixed on walls with dash fasteners and chromium plated screws purposefully made to fix the glass by drilling hole in the glass complete all as directed.

S&F in repair Water closet single piece/wall hanged pattern coloured of size 535 x 380 x 400 mm in repair as approved and complete all as specified and directed. Make : Jaquar Cat part No KUS-WHT-35851S300UF or equivalent in Hindware/Cera/Parryware

Supply only vitreous China valveless, 10 litres capacity, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and as directed.

S & F in repair Vitreous china squatting pan 'Orissa' pattern size 580x440 mm white with integral foot rest including connection to trap and flushing pipe complete all as specified and as directed.

S & F in repairs 15 mm dia WHB mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed. Make - Jaquar Cat No KUP-35011BPM or equivalent in Hindware/Parryware

S & F in repairs 15 mm dia wall mixer chromium plated screwed down high pressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specifie and as directed. Make - Jaquar Cat No FON-40119 or equivalent in Hindware/Parryware

S&F 200 mm dia brass chromium plated shower rose with swivel joints in repair complete all as specified and directed.

S&F 15 mm bore Bib tap in repair complete all as specified and directed. Make : Jaquar Cat Part No CON 107KN and equvalent in CERA/Parryware.

S&F in repairs 15 mm dia Angle valves/ stop cock ,fancy type and chromium plated screwed down highpressure with crutch or butterfly handle screwedboth ends for iron pipes or for unions and fixed complete all as specified and as directed. Make - Jaquar Cat No KUP-35053PM or equivalent in Hindware/Parryware

S&F Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe in repair complete all as specified and directed. Make : Jaquar/Parryware and equivalent .

S&F chromium plated toilet paper holder in repair complete all as specified and directed. Make : Jaquar Cat Part No ACN 1153N and equivalent in CERA/Parryware.

S&F 600 mm long brass chromium plated towel rail fancy type in repair complete all as specified and directed. Make : Jaquar Cat Part No ACN-1111NM and equivalent in CERA/Parryware.

S&F soap dish in repair complete all as specified and directed. Make : Jaquar Cat Part No ACN 1131N and equivalent in CERA/Parryware.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking sweeping cleaning & washing down with water to remove dust etc incl removal of old treatment of any description and 15mm thick screed bed in cement mortar 1:4 and applying one coat of neat cement slurry @ 3.00 kg/Sqm and applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Min wt of memebrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm including two coats of bituminious aluminium paint all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall complete all as specified and as directed.

S&F 110 mm PVC (SWR) bends any redius with access door complete all as specified and as directed.

M&L for SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and as directed.

M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to IS complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding, eves board and similar work to wall fixed with self tapping screws all as specified and as directed.

M&L for rolled section as in main and cross beams , purlins , rafters ,posts where connected to common rafter and running rails,frame work of eves board, tank staging work etc conforming to Fe- 410-w complete all as specified and as directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and as directed.

S&F rolled mild steel Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide on steel surfaces .

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete including fitting such as switch, sockets, ceiling rose, pendants socket,fan regulators any type, rectangular board ,light fittings,terminal boxes etc removing materials for taking credit and making good disturbed surfaces of walls floors and ceiling complete all as directed.

Taking down main switches, distribution boards and cut outs etc. of any type and capacity along with the existing boards and removing the same from site and making good the disturbed surface/portion of walls complete all as specified and directed By Engr-in-Charge.

Taking down carefully sub main wiring of any nos of wire and size with earth wire on wooden batten/surface conduit/casing caping complete with its all accessories complete all as specified and directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLSH copper conductor cables (multistranded) PVC insulated and unsheathed in and including PVC concealed conduit pipe as per site requirement (size not less than 20mm dia), medium grade with Modular sunken boxes & PVC/metal back plate for mounting modular type switches, sockets & regulators etc with cover plate modular type including supplying and laying PVC insulated and stranded unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire connected to earth dolly including cutting of chases in wall /ceiling etc and making good the disturbed surfaces match to existing with cement mortar and putty white /colour wash complete all as directed . Make: Havells/ Finolex/ Polycab.

All as per item No 95 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on an independent board.

All as per item No 95 above but cable 2.5 sqmm FRLSH for one 3/5 pin 6 Amp socket outlet point on the same board with other switch.

All as per item No 95 above but for one bell/buzzer point controlled by one bell push single pole one way .

All as per item No 95 above but for one 3/6 pin 16 amps socket outlet point on an independent board with cables of size 2.50 sqmm.

All as per item No 95 above but an independent board with cables of size 4.0sqmm.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge.Make:Legrand/Havell crabtree/L &T

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with outer cover complete all as specified and directed by Engr In charge. Make:Legrand/Havell crabtree/L &T

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr In charge.Make:Legrand/Havell crabtree/L &T

S&F in repair Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F LED retrofit lamp of capacity 12 watt, B-22 holder base with polycabonate body and aluminium heat sink warm white/day light complete all as specified and directed. Make- Syska/Havells/Bajaj.

S&F in replacement ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F in replacement electronic step type fan regulator 100 watt 230 volts 50Hz two module C/S deluxe type complete all as specified and directed. Make: Havells Crabtree/ Legrand/ L& T

S&F in replacement Sheet metal enclosure double door type for MCB TPN DB upto 4 way vertical type 415 volts with suitable busbar and neutral link , chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make: Schneider/ Legrand/Havells

S & F in replacement MCB TPN 415 volt any rating 63 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and directed. Make: Schneider/ Legrand/Havells

S&F in replacement sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way 240Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed. Make- Lauritz Kunudsen/ Sciender/Legrand

Supply and fixing in replacement 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning. Make- Lauritz Kunudsen/ Sciender/Legrand

S&F in replacement MCB Single Pole, 6 to 32 Amps 240 volts, 10KA breaking capacity, convenient to 'C' Curve complete all as specified and directed. Make- Lauritz Kunudsen/ Sciender/Legrand

Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make- Havells LED Pride Plus Neo Batten 10 W Cat Part No LHEXACP7IN1W010 or Equivalent make in Bajaj/C&S

S & F in repair LED light fitting 1x9W/10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.Make- Wipro / Bajaj /Philips

S& F in replacement LED tube light fittings of 20 wattage including rawl/plug ,making connection with and including 23/0 0076 flexible copper wire three core from connector to ceiling rose not more than 1.2 mtr fixed to wall firmly , complete all as specified and directed. Make - Syska/Philips /Havells

S & F in repairs LED wall mounting Decorative bed side wall light fixture made up of Polycarbonate, suitable for 9 W retrofit LeD Lamp B22 base with driver holder and LED lamp including connecting up with flexible copper conductor cable of suitable size complete all as specified and as directed. Make: Philips /Bajaj/Havells

S & F Wall fan made of sturdy Engineering plastic body complete voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 450mm direceted by Engr-in-charge. Make:Havells/Bajaj/CG.

S&F in replacement 25 Watt lighting luminaire with unique peanut optics to ensure uniform distribution, higher spacing between poles and maintenance free system for city roads and Streets, 50% Energy Savings, IP66 Protection PC and FG Cover, High Impact Resistance complete including LED Lamps and all accessories including bracket made out of 25mm bore GI pipe (light grade), 1.20 m long made to shape and fixed to existing pole or bldg by means of 2 Nos mild steel flat iron 40x6mm clamps with suitable size bolt, nuts & washers and connecting with three core flexible copper wire of size 23/0.0076 from ceiling rose to existing junction box complete all as specified and directed. Make Philips/ Havells/ Bajaj/ Crompton greaves.

M & L for Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5 connected to main control board all as specified and testing on completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc If earth resistance of earthing is not found (2 to 5 Ω) satisfactory earthing shall be redone by the contractor.

S&F sub main wiring with two single core FRLSH PVC insulated unsheathed multistranded copper conductor of size 6 Sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area FRLSH PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25 mm dia 'medium grade' PVC concealed conduits and fittings, complete all as specified and directed. NOTE: One unit length shall measured as two run of main wire and one run of conduit & earth wire Make: Havells / Finolex / Polycab.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE.Five star rated with brushless direct current motor (BLDC) all as specified and directed by Engr-In-Charge.Make-Usha Techno Air /Khaitan Magma/Bajaj Energos

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm all as directed and specified. Make-CG/Havells/Bajaj.

Supply and fix electric water heater, storage type plastic body with stailness steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection Pipe etc. Make- Bajaj Endure Series Gracio or Techno commercial equivalent make in Havells/Racold.

Supply, laying and testing (in replacement) of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core

M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand upto 18 cm thick and consolidated complete all as specified and directed. Note : Punned thickness 18 cm shall be measured only.

Supply and laying dry well burnt locally available brick sub class 'B' modular bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as specified and directed.

S &F for 40 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standing including taking down old /unserveciable existing pipe complete all as specified and directed. NOTE : Excavation and earth work shall be measured & paid separately.

vijay constrction co (BID ID -3346984)

M/S Ashok Kumar Jaswal (BID ID -3342772)

VIRINDER SINGH (BID ID -3347163)

khajuria builders (BID ID -3347369)

JOGINDER SINGH (BID ID -3347300)

SINGH CONST CO (BID ID -3347004)

RAMAN CONSTRUCTION CO (BID ID -3347141)

RAJ MOHD (BID ID -3346223)

PARDEEP SHARMA (BID ID -3346137)

ASHOK KUMAR GUPTA (BID ID -3347207)

VISHWANATH AND SONS (BID ID -3347428)

vmd traders (BID ID -3346995)