PROVN OF 01X GUARD REST ROOM WITH TOILET, SPL REPAIR TO COMPLETE DRAINAGE SYSTEM IN CAMP COMPLEX and A MESS BLDG NO T-1 and T-17 (SICK ANIMAL LINE) IN THE AOR OF AGE B/R-I UNDER GE 969 EWS

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out hard and dense soil complete all as specified and directed.

Excavation in trenches n. exc 1.5m wide and 1.5m depth for foundation etc or for shaft well, cesspits etc n.exc on plan and n.exc 1.5m depth and getting out in hard/dense soil complete all as specified.

-Ditto- all as per item ser No 02 but exc 1.5m depth to 3.00m and getting out in hard/dense soil complete all as specified and directed.

M&L plain cement concrete 1:4:8 type D-2, (using 40mm graded stone aggregate), in foundation, filling and mass concrete complete all as specified and directed.

Use & waste of formwork to rough finished surfaces of concrete, form work to sides of plinth beam, footings, bases of columns etc complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) as in foundation, footing, plinth beam, bases for columns etc complete all as specified and directed.

Use & waste of formwork to square or rectangle shape and fair finished surfaces of concrete, to sides of pillars, post , struts etc complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) as in columns etc complete all as specified and directed.

Formwork to soffits of fair finished suspended slabs such as roof slabs, floor slabs, landings and similar work n.exc 200mm thick (horizontal or sloping) etc complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use & waste of formwork finished fair to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M &L RCC (design Mix) M-25 (20mm graded stone aggregate) in beam bressummers, lintels over 1.5m span etc complete all as specified.

M&L TMT bars 10mm dia and over cut to length, bend to shape required including cranking, bending spirally for hookings for coils, hooking ends and binding with and including mild steel wire (aneeled) not less than 0.9mm dia.all as specified and directed.

M&L TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n exc 25 cm all as specified.

Removing of excavated soil not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified.

M&L brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L rendering 15 mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing with using integral waterproofing compound @ 3% by weight of cement including finishing the surface even and smooth without using extra cement complete all as specified. Note - W P C shall be measured and paid separately.

M&L rendering 5 mm thick in cement mortar 1:3 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement on ceiling surfaces complete all as specified.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified.

M&L for preparation of newly plastered surfaces of walls , applying two coats of distemper oil emultion, white or tinted complete all as specified.

M&L for preparation of newly plastered surfaces of ceilings, applying three coats of white wash complete all as specified and directed.

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exce 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L 75 mm thick cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) in sub base of flooring complete all as specified.

M&L 25 mm thick PCC 1:2:4 type B-1, (using 20 mm graded stone aggregate), including finishing surface of concrete topping even and rough as sub base/ flooring complete all as specified.

M&L for machine cut Kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in cement mortar 1:3 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including 15mm thick screed bed cement mortar 1:4 and jointed complete all as specified and directed.

M&L non - skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified.

M&L glazed ceramic tile 450 x 300 and 6-7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified.

S&F roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified.

M&L preparation of new steel surfaces of any description over 10 cm width or girth and priming with red oxide zinc chrome and painting with two coats of synthetic enamel paint on steel sheeting as in roofing complete all as specified.

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as etc complete all as specified.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

S&F 2nd class soft wood (kail) plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified.

S&F 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle boarde with commercial veneering on both faes. The size of rail and stile (second class hardwood) as per IS-1003 (part-I), kiln seasoned and chemically pressure treated, as directed as specified and directed.

S&F 2nd class soft wood (kail) glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkats, all as specified.

S&F glazed and skeleton shutters thickness 30 mm,(2nd class softwood), open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters supplied and fitted to chowkats if windows, ventilators, etc. are provided with stiles and rails as in SSR Part -I, section specified 8 clause 8.24(b), all as specified.

M&L for preparation of newly or previously untreated wooden surfaces of any description over 10 cm width or girth and priming with pink primer over two coats of synthetic enamel paint on wooden surfaces complete all as specified.

S&F 300mm long long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average wide of aperature 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2010 as specified.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item complete all as specified and as directed.

S&F steel ventilators with top hung shutter including hinges steel peg stay, squares no.exc 0.50 Sqm in each pane complete all as specified and directed.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

S&F butt hinges, 75 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

S&F butt hinges, 50 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

S&F 150mm long aluminium anodised, barrel tower bolt ISI marked complete all as specified.

S&F 100mm long aluminium anodised, barrel tower bolt ISI marked complete all as specified.

S&F 150mm long aluminium anodised cast type aluminium handle SI marked complete all as specified.

S&F 100mm long aluminium anodised cast type aluminium handle SI marked complete all as specified.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 110 mm bore of pipe complete all as specified.

S&F for PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore complete all as specified.

S&F for PVC (SWR) gully trap, plain with grating including jointing with solvent cement 110 mm bore complete all as specified.

S&F water closet (Orrissa pattern) complete including provision of lime concrete bedding including vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) in repairs complete all as specified.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single sokete any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F 75mm bore PVC (SWR) pipe single sokete any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F 110mm bore PVC (SWR) bend, plain including jointing with solvent cement complete all as specified.

S&F 100mm bore PVC (SWR) 'T 'any radius complete all as specified.

S&F 110mm bore PVC (SWR) vent cowl, plain including jointing with solvent cement complete all as specified.

S&F 500 Ltrs capacity rotational moulded polyethylene in white coloured three layered ISI marked water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as per specified and directed.

S&F second class softwood (kail) plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exc 13 Sqcm and n.exc 25 Sqcm complete all as specified and directed.

S&F second class softwood (kail) plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exc 3 Sqcm and n.exc 6 Sqcm complete all as specified and directed.

M&L for 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with nails to timber frame work in ceiling etc complete all as specified.

S&F vitreous china wash basin, white, flat back, size 580x450 (for Hospital use) excluding taps, waste, chain and plug and porcelain stopper but including brackets etc complete all as specified and directed.

S&F soap dish chromium plated, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified.

S&F for 4 mm thick figured glass pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified.

Supply only integral water proofing compound complete all as specified.

S&F 3-layer PP-R polypropylene random copolymer) concealed pipes of 16mm outer dia SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed to walls, ceilings or in floors etc complete all as specified and directed.

-Ditto- all as per Ser No 75 above but 20mm outer dia complete all as specified.

M&L lagging to 20mm bore pipe exposed PPR tubing all around (including provisions of lagging on pipe fitting ie., unions, elbows, nipples, tees etc) with 40mm thick bonded mineral wood performed 'SNAP ON' pipe section of density 144 Kg/Cum confirming to IS-9842 with chicken mesh wire netting 25 gauge, 20mm mesh with 0.01 mm aluminium foil complete all as specified and directed.

S&F for bib taps, cast copper alloy chrominium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F PVC connections 15mm dia with PTMT nuts of length 450mm complete all as specified and directed.

S&F chromium plated shower rose 125mm dia with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F stop valves, cast copper alloy fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed to 15mm bore of pipe complete all as specified and directed.

S&F gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia bore pipe complete all as specified and directed.

M&L for PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete etc etc all as specified and directed by Engr-in -Charge.

M & L for walling of random rubble stone masonary uncoursed well bonded solidily hearted built in CM 1:4 etc all as specified and directed by Engr-in-Charge.

M&L for providing cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in coping etc all as specified and directed by Engr-in-Charge.

M&L for rendering 15mm thick in cement mortar 1:4 on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing including finishing to surfaces even and smooth without using extra cement etc all as specified and directed by Engr-in-Charge.

M&L for extra stone walling for hammer dressing in faces stones of random rubble walling uncoursed fro granite or trap stone etc all as specified and directed by Engr-in - charge.

M&L for cement concrete 1:3:6, type C2, (using 40mm graded stone aggregate) as in surface channel and drains all as specified and directed by Engr-in -Charge.

Extra for forming fair finished drain channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc all as specified and directed by Engr-in-Charge.

M&L for providing precast cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) and set in cement mortar 1:6 in landings, cover slabs (for manholes/ drain cover) etc all as specified and directed by Engr-in - charge.

M&L for 75mm thick cement concrete type C-2, 1:3:6 (40mm graded stone agrregate) as in sub base of floors, finished even and fair over well/rammed/ compacted earth complete all as specified.

S&F chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors including screed bed 15mm thick in CM 1:4 complete all as specified and directed.

M&L plain cement concrete, 1:2:4 type B-1 (using 20mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified.

S&F 10 user LLDPE septic tank conventional designed to carry sewae and sludge water, excavation in any type of soil,PCC 1:4:8 below foundation, vent shaft connection etc complete all as specified and directed.

M&L for construction of soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4m dia and 3m depth complete all as specified.

RCC NP3 150 mm diameter Pipes laid on150 mm thick bed with excavation in any type of soil, including manholes/drop manhole of standard size made of Brick masonry/ RCC/Precast RCC with SFRC ventilating cover and frame includes all items and activities to execute and make sewer line functional for depth 0.70m to 1.65m complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B-1, (using 20mm graded stone aggregate) and set in cement mortar 1:6 in landings, cover slabs (for manholes/ drain cover) etc all as specified and directed

M&L plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) surface channels and drains concrete complete, all as specified.

M&L walling of random rubble stone masonary built in cement mortar 1:6, uncoursed, well bounded, bedded and solidly hearted and pointed flush the surface in contact with earth in the same mortar as the work proceeds complete, all as specified.

M&L plain cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in benching, bed plates, coping and the like including necessary formwork and finishing all exposed surface of concrete as per clause 4.11.16.2(a) & (d) of SSR Part-I complete all as specified.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified of random rubble waling uncoursed or brought of to courses with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm granite and trap stone all as specified.

M&L rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brick work in CM 1:6 complete all as specified and directed.

Taking down plastering on lathing (other than wire-netting), without removing lathing, in cement lime or cement mortar complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of wall and celling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness inlcuding cover fillets complete all as specified and directed.

M&L for 4 mm thick veneered decorative plywoode,grade 1 (with decorative face veneers on one faces) in ceiling, fixed with nails to timber frame work complete all as specified.

M&L for 4 mm thick veneered decorative plywoode,grade 1 (with decorative face veneers on one faces) on wall, fixed with nails to timber frame work complete all as specified.

M&L plain fillets square rectangular or triangular in section using 2nd class soft wood (kail) clean swan secured with nails not exc 3 sqcm in section complete all as specified.

S&F in repair 2nd class softwood (kail) in scantling clean swan timber framed and fixed to the position including dismantling complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceed 1.5 Sqm complete all as specified and directed.

Taking down chowkats or frames but with shutters (without taking off shutters from the frame) exceed 1.5 Sqm and not exceed 4.00 sqm complete all as specified and directed.

M&L glazed and skeleton shutters thickness 30 mm, (2nd class softwood), open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters supplied and fitted to chowkats if windows, ventilators, etc. are provided with stiles and rails as in SSR Part I, section specified 8 clause 8.24(b) complete all as specified and directed.

M&L for 2nd class softwood (kail) 35mm thick plain frame panelled shutter with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L preparation of new wooden surface of any description and two coat of synthetic enamel paint, not otherwise described, over 10cm width or girth complete all as specified and as directed.

M&L preparation of old wooden surface of any description and two coat of synthetic enamel paint, not otherwise described, over 10cm width or girth including complete removal complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts 100 mm of extruded section and fixed complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts 200 mm of extruded section and fixed complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 200 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F aluminium handles 100 mm , cast type,anodised complete all as specified and directed.

S&F aluminium handles 150 mm , cast type,anodised complete all as specified and directed.

S&F sheet glass thickness 4.00 mm thick ,ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane including hacking out old brioken glass complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F 2nd class softwood (kail) clean sawn with butt joints eaves boards 20 mm thick complete all as specified and as directed.

M&L weather boarding, 25 mm thick, wrought both sides, V-jointed to give 20mm laps and fixed complete all as specified and as directed.

Dismantling floor hearth wall tilling including cement mortar bedding, removing serviceable tiles to store and rubbish of the permishes complete all as specified and directed.

M&L for 25 mm thick PCC type B1 1:2:4 (using 20 mm graded stone aggregate) as in slope correction under floor tile complete all as specified and directed. .

M&L non skid coloured printed ceramic tile 7 to 8 mm thick (Square / rectangular) area of each tile exc 0.18 Sqm but n.exc 0.38 Sqm,in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colur of tiles over and including 15 mm thick screed bed in CM 1:4 complete all as specified.

Demolition of cement concrete (unreinforced) in any position and any thickness (below or above ground level) complete all as specified.

Taking down carefully copper/aluminum point wiring (light fan, socket or power) complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces to match with existing specifications of walls, floors etc. complete, all as specified.

M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 volt grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked drawn through wiring system surface on wall with the help of heavy duty ISI mark PVC casing capping strip in any length wiring system and along with its all connected fittings accessories including providing of wooden board with bakelite sheet for housing / mounting of switches sockets, regulators etc and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ceiling area of new wiring system for one light point / fan point controlled by one switch of one way point wiring system complete, all as specified & directed by EIC

-Ditto- all as per item No 132 one 3 pin 5 Amp switch socket outlet on independent board, all as specified.

-Ditto- all as per item No 132 one 3 pin 5 Amp switch socket outlet on same board with accessories, all as specified.

-Ditto- all as per item No 132 but 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws guttier/plug etc PVC unsheathed cable into and including wooden board with bakelite sheet and PVC insulated FRLS cable of size 2.5 Sqmm as earth continuity conductor for 15 amps switch socket outlet on independent board, all as specified.

S&F switch piano flush type, single pole, one way 5 Amp 240 Volts, complete all as specified and directed

S&F switch piano flush type, single pole, 16 Amp 240 Volts, complete all as specified and directed

S&F switch piano flush type, single pole, one way 6 Amp 240 Volts, complete all as specified and directed

S&F switch piano flush type, single pole, 15 Amp 240 Volts, complete all as specified and directed

S&F flush type socket 6A/16A 2/3 pin combined, 2 in 1, 3 pin, 5 Amps, complete all as specified and directed

S&F flush type socket 6A/16A 2/3 pin combined, 2 in 1, 3 pin, 16 Amps, complete all as specified and directed.

S&F flush type socket outlet, 2 in 1, 3 pin, 5 Amps, complete all as specified and directed.

S&F flush type socket outlet, 2 in 1, 3 pin, 15 Amps, complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified and directed.

S&F lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fitting complete all as specified and directed

S&F ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body all as specified and directed

S&F 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sqmm 02 core nominal cross section in service connections, all as specified.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V,50 Hz, RPM 1200, copper winding of sweep 300m, all as specified.

S&F sheet metal enclosure MCB DB SPN 12 way with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonary etc and making good of disturbed surface complete all as specified and directed.

S&F in repairs MCB SPN 40 to 63 Amp rating 240V, 10KA 'C' curve complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240 Volts, 'C' curve complete all as specified and directed.

S&F MCB single pole 6 to 32 Amps, 240 Volts, 'B' curve complete all as specified and directed.

S&F LED inverter bulb 12 watt, all as specified.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. all as specified.

S&F building security light LED fitting 35 watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete, all as specified.

Supply, laying & testing cable XLPE insulated screened, PVC bedded glavanised steel strip or wire armoured electric power cable (heavy duty) 1100 V grade with stranded aluminium conductor of size 25sqmm x 02 core complete all as specified.

S&F ceiling fans complete with blades, down, rods, electronic regulator and accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE 5 star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F stepped type fan regulator, 120Watt flush type complete all as specified.

S&F square shape 18 watt 220 Volts AC recessed/surface 1x1 feet type with high efficency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for rof ceiling including connecting upt with three core flexible copper conductor cable of suitable size complete all as specified.

S& F LED light fitting 1x10 bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

Supply spread river sand to required width at bottom and top for cable cushioning all as specified in clause 19.75 of SSR Part-I, all as specified. Note:- Thickness of sand will be measured after pumping.

Supply and laying common burnt bricks of sub class 'B' old size laid at right angle on the cable complete in trenches for cable protection complete all as specified and directed.

S&F GI tubing light grade 40mm dia with all fitting, laid in trenches all as specified and directed.

M&L in repairs for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6, type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion. Note : The rate is ilnclusive of necessary earth work, RFR and removal etc

S&F GI tubing medium grade 25mm dia with all fitttings and fixed complete to walls and ceilings or laid in floors including taking down existing GI/CI pipe complete, all as specified and directed.

S&F Gun metal gate valve 20mm bore with iron hand wheel head, screwed both ends for iron pipes and fixed complete including dismantling old unserviceable gate valve complete all as specified.

M&L for cutting existing pipe line GI/CI pipe for inserting new connection including tee, elbow and connected items complete all as specified and directed.

M/S STARE BUILDERS (BID ID -3441290)

M/S ESS EMM ENTERPRISES (BID ID -3437755)

M/S GHULAM RASOOL LONE (BID ID -3447253)