Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹64.7 LAccepted-AOC | ₹64.7 L Quoted ₹65.0 L | 1 | Accepted-AOC WORK AWARDED |
| 2 | 2₹67.4 LRejected-AOC 25 A RR SAMY LANE KATTOOR COIMBATORE 641009 | COIMBATORE | COIMBATORE | TAMIL NADU | 641009 | ₹67.4 L | 2 | Rejected-AOC Second Lowest |
| Sl No | Description | Qty | Unit | rv electricals L2 | SETHARAM ELECTRICAL AND CONSTRUCTION L1 |
|---|---|---|---|---|---|
| 1.00 | Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 No 20 persons Capacity Gearless Passenger cum Bed lift with machine room as per the following Technical specifications.
Technical Specifications:
1.Location: GVMCH New CEMONC Block at Mundiyampakkam.
2.No of lift: 1 No
3.Type of lift: Passenger cum bed lift. (1360 Kgs)
4.Capacity of lift: 20 persons capacity Gearless passenger cum bed lift
5.Speed: 1.0 M / sec
6.Type of drive: Specific variable voltage variable frequency V3F drive with enhanced ride
7.No of floors: 5 (Ground + 4 Floors)
8.Total travel: 16.5 Mtrs Travel
9.Leveling accuracy: High level accuracy with smooth & jerk free stopping
10. Construction of Car: 18SWG High quality S.S 304 Grade car neat hairline finish, S.S. hand rail, S.S. floor line finish, Perspex false ceiling, stretcher impact protection.
11. Position of machine: Directly above the lift well.
12. No. of landing entrance: One in front - 5 Nos
13. No. of car entrance: one in the front only
14. Car entrance door: power operated V3F drive side opening sliding 18SWG stainless steel hariline finish.
15. Landing entrance door: power operated V3F sliding, opening 18SWG stainless steel hairline finish with provision for emergency key.
16.Lift well existing: 3000mm X 2400mm
17.Lift pit depth available : 1600 mm
18.Car (Clear inside): 1600mm (wide) X 2400mm (Depth)
19.Car Clear opening: 1200mm width X 2000mm height. | 1 | No | 30,00,000 ₹30 L | 29,00,000 ₹29 L |
| 1.0120.Lift machine room available: 4350mm width X 5500mm 21. Power supply: 400/440V 3 phase, 50 cycles/sec A.C. Supply for power and 230 V, 50 22.Control: Microprocessor based simplex selective collective simplex 23.Car fittings: Sleek LED light fitting with 300mm sweep cabin fan. 24.Lift well: R.C.C. construction with brick masonry. 25. Indication: UP / DOWN digital direction and position indicator for all landing and in car (25mm Height, seven segment Digital Floor position indicator scrolling type). 26.Emergency Alarm Bell: Battery operated alarm bell to be provided with Automatic charging device. 27.Emergency light: Battery operated light to be provided with Automatic charging device. 28.Fireman's switch: To be provided at ground floor. 29.Minor builders work: To be provided by the lift contractor. 30.Scaffolding: To be provided by the lift contractor. 31.Sill angles and facia plates: To be provided by the lift contractor. 32.Steel for lift machinery: To be provided by the lift contractor. 33.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by the lift contractor during the guarantee period of one year. 34.Automatic Rescue Device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, inverter, under voltage protection system etc., complete with all accessories. | |||||
| 1.0235. Provision of intercom with phone: To be provided by the lift contractor 3 points EPABX system at three places vide 1) inside the car 2) Head room 3) at ground floor attender room. 36.Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by the lift contractor. 37. Floor announciator with music, included. 38.Special features a. Infra red door sensor with full height screen. b. Tubular S.S hand rail in cars. c. Voltage stabilizer for circuit control. d. Stainless steel signal fixtures. e. Vendal proof S.S. Button with S.S. cover. f. S.S. hairline finish door frames for landing doors. g. VF door Register signal. h. Call register signal. i. Stainless steel facia plate for car operating panel and landing fixtures. j. Steel ladder for machine room and ladder for lift shaft pit. k. On - Off switch for fan and light. l. Over load warning indicator with audio announcement. m.Fall width half height rear panel mirror. | |||||
| 1.0339.Provision of architraves covering all three sides upto a width of 300 decorum sheet of plywood with TW frame with aluminium beading architraves should also cover the thickness of still level door frame at the landing and indicator boxes at all landings. 40. Other standard features: Voltage stabilizer for control units, Over speed governor, phase failure and phase reversal relay alarm bell, T-Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limits switch, main suspension ropes counter weights lifting hoist for mounting the machineries. 41.Guarantee: Guarantee for the materials workmanship of equipments complete should be offered by lift firm for a period not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over. Necessary spares and tools required for the maintenance for a period of one year. 42. Supply operation and maintenance manual with necessary tools for operation. The list of tools required should be detailed by the contractor in a separate sheet duly signed by the contractor. (Johnson / KONE / Equivalent) | |||||
| 2.00 | Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 No Geared Dump lift without machine room for the capacity of 240 Kgs as per IS 14665 standard and the following Technical specifications.
Technical Specifications:
1.Location: GVMCH New CEMONC Block at Mundiyampakkam.
2.No of lift: 1 No
3.Type of lift: Dump lift.
4.Capacity of lift: 240 Kgs
5.Speed: 1.0 M / sec
6.Type of drive: Single speed drive
7.No of floors: (Ground + 4 Floors)
8.Total travel: 16.5 Mtrs Travel
9.Leveling accuracy: High level accuracy with smooth & jerk free stopping
10. Construction of Car: High Quality Precoated steel-Ivory & yellow.
11. Position of machine: Directly above the lift well.
12. No. of landing entrance: One in front, Total - 5 Nos
13. No. of car entrance: One in front only
14. Car entrance door: No Door.
15. Landing entrance door: Collapsible gate MS painted - Black with landing door frame.
16.Lift well existing: 1900mm X 1900mm
17.Lift pit depth available : 750 mm
18.Car size : 1000mm (width) X 1000mm (Depth) X 1200mm (Height)
19.Car Clear opening: 1000mm (width) X 1200mm (height).
20.Lift machine room available: 1600mm (widt)h X 1500mm (depth).
21. Power supply: 400/415V 3 phase, 50 cycles/sec A.C. Supply for power and 230 V, 50 HZ, single phase, supply for lighting. | 1 | No | 12,00,000 ₹12 L | 11,50,000 ₹11.5 L |
| 2.0122.Control: External Extended push button with / without attendent. 23.Car fittings: Indirect and LED light. 24.Lift well: R.C.C. construction with brick masonry. 25. Indication: UP / DOWN digital direction and position indicator for all landing and in car. 26.Minor builders work: To be provided by the lift contractor. 27.Scaffolding: Included in this scope. 28.Sill angles and facia plates: Included in this scope. 29.Steel for lift machinery: Included in this scope. 30.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by the lift contractor during the guarantee period of one year. 31.Lift License: Preparation of Drawing, payment of charges to CEIG safety certificate as per lift act should be done by the lift contractor. 32.Special features a. Up and Down arrows in landing only. b. Steel cubical for controller. c. Dished stainless steel push box cover with push. d. Automatic bilingual door open voice anounciator. e. MS door frame with suitable MS steel for landing entrance. f. Lift duty motor of adequate capacity, reduction warm gear electromagnet break with compressor springs, over speed governor, phase failure & phase reversal relay alarm bell T-guide backets of car and counter weight Rubbes padding under winding units car safety gears buffers electro mechanical door lock, emergency key, side supporting angle, motor over load protection devices final limit switch, main suspension ropes, counter | |||||
| 2.02weights lifting hoist for mounting the machineries. 33.Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period not less than one year. 34. Site testing in accordance with IS 14665 should be carried out at the time of handing over. 42. Supply operation and maintenance manual with necessary tools for operation and a set of spare required for 1 year. (Dump lift should be Johnson / KONE / OTS / Equivalent) | |||||
| 3.00 | Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End | 16 | Pts | 2,500 ₹40,000 | 2,500 ₹40,000 |
| 4.00 | Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb. | 10 | Nos | 850 ₹8,500 | 820 ₹8,200 |
| 5.00 | Supply and fixing of 1 no. 6A two module 3 pin socket, 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End | 10 | Pts | 750 ₹7,500 | 750 ₹7,500 |
Tender Value
₹64.7 L
EMD Value
₹42,500
Closing Date
12 Mar 2026, 3:00 pmClosed
The Superintending Engineer, PWD.,
The Superintending Engineer, PWD., Buildings Construction and Maintenance Circle,Tiruvannamalai-4.
Providing Additional 1 No. 20 Person Bed cum Passenger Lift, 1 No. Dump Lift and Power Mains Arrangements to the Additional Floors for the Extension of Maternal and Child Health Building (CEMONC) in Government Medical College and Hospital at Mundiyam
2026_PWD_671514_1
86/TVM-CLE/25-26/2/ Dt.03.03.2026
Open Tender
Electrical Works
90 days
Mundiyampakkam
Please refer Tender documents.
8 documents required · 8 mandatory
₹0
₹42,500
12 May 2026
6 Mar 2026
12 Mar 2026
6 Mar 2026
12 Mar 2026
6 Mar 2026
Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 No 20 persons Capacity Gearless Passenger cum Bed lift with machine room as per the following Technical specifications. Technical Specifications: 1.Location: GVMCH New CEMONC Block at Mundiyampakkam. 2.No of lift: 1 No 3.Type of lift: Passenger cum bed lift. (1360 Kgs) 4.Capacity of lift: 20 persons capacity Gearless passenger cum bed lift 5.Speed: 1.0 M / sec 6.Type of drive: Specific variable voltage variable frequency V3F drive with enhanced ride 7.No of floors: 5 (Ground + 4 Floors) 8.Total travel: 16.5 Mtrs Travel 9.Leveling accuracy: High level accuracy with smooth & jerk free stopping 10. Construction of Car: 18SWG High quality S.S 304 Grade car neat hairline finish, S.S. hand rail, S.S. floor line finish, Perspex false ceiling, stretcher impact protection. 11. Position of machine: Directly above the lift well. 12. No. of landing entrance: One in front - 5 Nos 13. No. of car entrance: one in the front only 14. Car entrance door: power operated V3F drive side opening sliding 18SWG stainless steel hariline finish. 15. Landing entrance door: power operated V3F sliding, opening 18SWG stainless steel hairline finish with provision for emergency key. 16.Lift well existing: 3000mm X 2400mm 17.Lift pit depth available : 1600 mm 18.Car (Clear inside): 1600mm (wide) X 2400mm (Depth) 19.Car Clear opening: 1200mm width X 2000mm height.
35. Provision of intercom with phone: To be provided by the lift contractor 3 points EPABX system at three places vide 1) inside the car 2) Head room 3) at ground floor attender room. 36.Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by the lift contractor. 37. Floor announciator with music, included. 38.Special features a. Infra red door sensor with full height screen. b. Tubular S.S hand rail in cars. c. Voltage stabilizer for circuit control. d. Stainless steel signal fixtures. e. Vendal proof S.S. Button with S.S. cover. f. S.S. hairline finish door frames for landing doors. g. VF door Register signal. h. Call register signal. i. Stainless steel facia plate for car operating panel and landing fixtures. j. Steel ladder for machine room and ladder for lift shaft pit. k. On - Off switch for fan and light. l. Over load warning indicator with audio announcement. m.Fall width half height rear panel mirror.
39.Provision of architraves covering all three sides upto a width of 300 decorum sheet of plywood with TW frame with aluminium beading architraves should also cover the thickness of still level door frame at the landing and indicator boxes at all landings. 40. Other standard features: Voltage stabilizer for control units, Over speed governor, phase failure and phase reversal relay alarm bell, T-Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limits switch, main suspension ropes counter weights lifting hoist for mounting the machineries. 41.Guarantee: Guarantee for the materials workmanship of equipments complete should be offered by lift firm for a period not less than one year. 41. Site testing in accordance with IS 14665 should be carried out at the time of handing over. Necessary spares and tools required for the maintenance for a period of one year. 42. Supply operation and maintenance manual with necessary tools for operation. The list of tools required should be detailed by the contractor in a separate sheet duly signed by the contractor. (Johnson / KONE / Equivalent)
Design, Engineering, Supply, Fabrication, Erection, Testing, commissioning and handing over of 1 No Geared Dump lift without machine room for the capacity of 240 Kgs as per IS 14665 standard and the following Technical specifications. Technical Specifications: 1.Location: GVMCH New CEMONC Block at Mundiyampakkam. 2.No of lift: 1 No 3.Type of lift: Dump lift. 4.Capacity of lift: 240 Kgs 5.Speed: 1.0 M / sec 6.Type of drive: Single speed drive 7.No of floors: (Ground + 4 Floors) 8.Total travel: 16.5 Mtrs Travel 9.Leveling accuracy: High level accuracy with smooth & jerk free stopping 10. Construction of Car: High Quality Precoated steel-Ivory & yellow. 11. Position of machine: Directly above the lift well. 12. No. of landing entrance: One in front, Total - 5 Nos 13. No. of car entrance: One in front only 14. Car entrance door: No Door. 15. Landing entrance door: Collapsible gate MS painted - Black with landing door frame. 16.Lift well existing: 1900mm X 1900mm 17.Lift pit depth available : 750 mm 18.Car size : 1000mm (width) X 1000mm (Depth) X 1200mm (Height) 19.Car Clear opening: 1000mm (width) X 1200mm (height). 20.Lift machine room available: 1600mm (widt)h X 1500mm (depth). 21. Power supply: 400/415V 3 phase, 50 cycles/sec A.C. Supply for power and 230 V, 50 HZ, single phase, supply for lighting.
22.Control: External Extended push button with / without attendent. 23.Car fittings: Indirect and LED light. 24.Lift well: R.C.C. construction with brick masonry. 25. Indication: UP / DOWN digital direction and position indicator for all landing and in car. 26.Minor builders work: To be provided by the lift contractor. 27.Scaffolding: Included in this scope. 28.Sill angles and facia plates: Included in this scope. 29.Steel for lift machinery: Included in this scope. 30.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by the lift contractor during the guarantee period of one year. 31.Lift License: Preparation of Drawing, payment of charges to CEIG safety certificate as per lift act should be done by the lift contractor. 32.Special features a. Up and Down arrows in landing only. b. Steel cubical for controller. c. Dished stainless steel push box cover with push. d. Automatic bilingual door open voice anounciator. e. MS door frame with suitable MS steel for landing entrance. f. Lift duty motor of adequate capacity, reduction warm gear electromagnet break with compressor springs, over speed governor, phase failure & phase reversal relay alarm bell T-guide backets of car and counter weight Rubbes padding under winding units car safety gears buffers electro mechanical door lock, emergency key, side supporting angle, motor over load protection devices final limit switch, main suspension ropes, counter
weights lifting hoist for mounting the machineries. 33.Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period not less than one year. 34. Site testing in accordance with IS 14665 should be carried out at the time of handing over. 42. Supply operation and maintenance manual with necessary tools for operation and a set of spare required for 1 year. (Dump lift should be Johnson / KONE / OTS / Equivalent)
Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End
Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb.
Supply and fixing of 1 no. 6A two module 3 pin socket, 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End
Supply and fixing of single box type 4' 18 W LED fitting complete with TW round blocks on wall or ceiling with 18 W LED tube light crystal glass connection ( Havells / equivalant) with PVC unsheathed Copper leads from terminals to the fitting.
Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod with fan clamp with Fan MS Box.
Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall.
Supply and fixing of louvered shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan.
Supply and fixing of Vertical type 4 way Triple pole and neutral MCB Double door Distribution board in sheet steel enclosure with metal door with IP42 protection with 1 No. 63A FP MCB Isolator as incoming and 12 Nos. of 6A to 32A SP MCB outgoing on wall with suitable angle iron frame work with Cable entry box on top or bottom with earth connection only. The MCB DB and MCB's should be with Legrand / Hager make only.
Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40 A FP MCB as incoming and 4 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End
Supply and fixing of 63A FP MCB in flush with sheet enclosure in wall with earth connection. (Legrand (MDS) / Hager (L&T) make).
Supply and fixing of 32A FP MCB in flush with sheet enclosure in wall with earth connection. (Legrand (MDS) / Hager (L&T) make).
Supply and run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour.
Supply and run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire and making good of the concealed position.
Supply and erection of 800A, 4 Pole 50 KA, air circuit breaker (ACB) Microporcessor Based, EDO Breaker switch mounted cubical panel board bus bar chamber dust and vermin proof and accommodating the following sign with Thermal Magnetic Release units with the following items of work complete to satisfy the latest IE rules and CEIG guidelines, Supply and fixing of suitable bus bar chamber made up of 16SWG MS sheet steel (1.6mm) with 8 Nos. of 2 1/2" X 1/2" tinned copper bus bar for 3 phases and neutral (50mm x 10mm) and 2 Nos. of eathing bus of size 1" X 1/8 tinned copper bus (25mm x 3mm) on suitable bus bar insulator (Epoxy insulator) with maximum creepage distance and supported on MS Base channel frame work of size 6' x 3' - 1 set Incoming 1) Supply and fixing of 1 No. 800A, 4 Pole 50 KA, air circuit breaker (ACB) Microprocessor Based, EDO Breaker switch confirming to IS as per CEIG, IE rules in force with inter connection and terminations as required in specification.
Supply and fixing of 45 KVA capacity three phase microprocessor controlled air cooled unbalanced electronic servo voltage stabilizer with Input Volts 29V-465V Output Volts 400V, Voltage Regulation of ±1%, Output Volt Adjust 395V- 405V, Input Frequency, 47 Hz-52Hz, Output Frequency 50 Hz± 0.5%, Voltage Correction - 35V/Sec, with LCD Display for Input and Voltage Reading high / low voltage cut off and single phase preventor and with manual bypass arrangements for lift unit.
Supply and fixing of 30 KVA capacity three phase microprocessor controlled air cooled unbalanced electronic servo voltage stabilizer with Input Volts 29V-465V Output Volts 400V, Voltage Regulation of ±1%, Output Volt Adjust 395V- 405V, Input Frequency, 47 Hz-52Hz, Output Frequency 50 Hz± 0.5%, Voltage Correction - 35V/Sec, with LCD Display for Input and Voltage Reading high / low voltage cut off and single phase preventor and with manual bypass arrangements for lift unit.
Supply and Laying of 3 1/2 x 185 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.
Supply and clamping of 3-1/2 x 185 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.
Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection.
Supply and providing cable end termination of 3-1/2 x 185 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete.
Supply and providing of Plate Earth Electrode with 2mts of Class 'B' GI pipe 40mm and 3mm thick of copper plate of size 12" x 12" x 3mm revitted to the pipe at one end and providing a funnel at the top end with 1 runs of 25mm x 3mm copper flat from the copper plate to the top of the electrode and embedding the above electrode in a pit to be excavated at a depth of 3mt and of size 60cm x 60cm and filling up the pit with charcoal, salt, sand.
Supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.
Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.
Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.20 MB
MundiyampakkamLift_Cond1.pdf
Tender Documents • 0.44 MB
BOQ_806990.xls
BOQ • 0.34 MB
Download all tender documents and submit your bid