SPL REPAIR TO ROOF OF BLDG NO P-84, P-284, P-1175, P-106, P-576A OF IBSC AND STN HQ AND SPL REPAIR TO BLDG NO P-337/01 TO 04 (CIVILIAN GOVT MD ACCN) OF GE ALWAR AT ITARANA MIL STN ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete .

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete .

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete .

Demolition of cement concrete (un-renforced) in ground floor and paving. N exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc laid, beded and pointed in any mortar including removing the dismantled material complete .

M&L for Granite (of any type) tiles 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete

Taking down Chowkatts or frames with shutters (without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each.

Taking down Chowkatts or frames with shutters (without taking off shutters from the frame n. exc 1.5 sq. m each.

Taking down shutter of any descriptioon exc 1 Sqm but n exc 2 Sqm each.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate), 25mm thick, as in Sub base complete .

M&L for Non Skid white ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, Complete.

M&L Non skid white Ceramic tiles7 to 8 mm thick in light shade(square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick cement screed in cm 1:6 complete.

All as per srl item No 13.00 but on walls over 10 mm thick rendering in CM 1:4 complete.

M&L 75 mm thick PCC(1:3:6) type C2 (using 40mm graded stone aggregate ) as in plinth protection finished even and smooth without using extra cement complete.

M&L Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete .

M&L Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete .

Supply and fixing GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the size 15 mm bore. Note :-excavation earth work will be measured and paid saperatly.

Supply and fixing GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the size 20 mm bore. Note :-excavation earth work will be measured and paid saperatly.

Supply and fixing GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe of the size 25 mm bore. Note :-excavation earth work will be measured and paid saperatly.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed tinned tacks or GI wire stampe or nails and screws .

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete.

S&F Butt hinges 100mm long medium weight, stainless steel complete.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete.

S&F 150mm 'D' type Aluminium handles, anodised complete.

S&F 150mm extruded aluminium alloy handles ,fabricated type anodised all as specified.

S&F exctruted aluminum alloy with galavanisied mild steel hing pin Butt hinges 100mm long type B-21 .

S&F aluminium anodised barrel tower bolt 200 mm long extruded section and fixed

S&F aluminium alloy anodised sliding door bolt with hasp and staples type, 300mm long bolt type and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections fixed all as specified.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, cooler stands (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete confirming Fe 410 (Gde E-250 quality A) & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.

M&L for flat iron as in hold fast, hooks, cleats welded to angle iron door/window frames etc complete all as specified and directed

S&F anodised aluminium powder coated (Mimimum thickness of powder coating 50 micron) frame for doors, windows, ventilators, with one or more rebates including joining cleat for fixing etc complete .

S&F aluminium powder coated (Mimimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,anodised aluminium fitting such as peg stays 150 mm long (01 Nos),hinges type B-1 100 mm long (2 nos) suitable handle (1 no) complete all as specified complete.

S&F Sheet glass, ordinary quality, in squares exc 0.5 sq. m each pane 5.5 mm in thickness complete.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer .

Cutting holes in brick/stone walls n. exc. Half brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as specified and directed

S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete . Note :- The measurement shall be taken of front elevation and not girthwise.

S&F in repairs 25 mm dia stainless steel curtain rod complete with SS brackets as required at site and SS side caps fancy type fixed in position by drilling holes in walls and fixed the brackers with rawl plug and steel screw compete .

M&L Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in landing, chajjas, shelves and similar articler as directed including necessary scaffolding complete.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete.

All as per srl item No 45.00 above but 6 to 8 mm dia TMT bars.

Taking down cement plaster any description on brick or stone any description complete.

M&L Rendring 10mm thick in CM 1:6 on brick work or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement all as specified.

M&L for rendering 15mm thick in CM 1:4 on brick or concrete wall surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & fair complete.

Supply only Integral waterproofing compound complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two or more coats of 100 % premium acrylic emulsion Paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004 ,Alkali and fungal resistance dirt resistance ,exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of Exterior primer @ 0.9 litre /10 sqm over 1mm thick Birla white wall care putty complete all as specified and directed.

M&L for complete removal of existing treated surfaces of wall and applying two or more coats of 100 % premium acrylic emulsion Paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance dirt resistance ,exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of Exterior primer @ 0.9 litre /10 sqm over 1mm thick Birla white wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of Oil bound distemper over a coat of alkali resistant primer on walls including 1 mm thick wall putty complete all as specified and directed.

M & L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint over and inclucluding 1 mm thick Birla white wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

Material and labour preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

Material and labour complete removal of existing treatment of ceilings & applying two coats of white wash complete all as specified and directed.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including taking down of existing tank complete all as specified and directed.

S&F in repair ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified and directed.

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed bore in dia 15mm complete all as specified and directed.

S&F in repair white vitreous china wash hand basin 'Flat back' of size 450x300mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as specified and directed.

S&F in repair stop valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified and directed.

S&F in repair Stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified and directed.

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F in repair PVC waste pipe of 32mm bore of suitable length for WHB/Urinal/sink complete all as specified and directed.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs, vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of Cement concrete bedding, connection to trap and Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level etc complete including making good to disturbed surfaces of floor to match with existing surface all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets fixed in repairs complete all as specified and directed.

S&F 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete all as specified and directed.

S&F in repair Stainless steel plate rack 1mm thick of size 900mm x 900mm x 250mm including fixed with rawl plug and screws on walls complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls/floor including taking down of existing complete all as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm complete all as specified and directed.

S&F PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/walls and making good the disturbed surface as per existing including taking down of existing complete all as specified and directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as specified and directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete all as specified and directed

S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

Taking out existing roof treatment of any description including plaster cement concrete etc rubbing with water including 20mm thick cement plaster in CM 1:3 on roof slab mixed with WPC 3% by weight of cement including finishing fair and even complete all as specified and directed. Note :- WPC shall be measured and paid seperately.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified and directed.

M&L water proofing treatment to RCC roof slab including parapet comprising of following course of treatment/specified from bottom to top (a) (i) The surface shall be painted with one coat of cold applied bituminous primer conforming to IS:3384, @0.40 Kg per Sqm applied a coat of hot blown bitumen @ 1.20 Kg per Sqm over a coat of bituminous primer, conforming to IS:338 (iii) APP based polymeric membrane not less than 3 mm thick weighing not less than 3.5 Kg/sqm, reinforced with polyst non-waver fabric (weighing not less than 150gm/sqm) aed. It shall be laid by torch application (two coat of heat resisting paint over App membrane all as specified and directed by Engineer-in-charge. side overlaps shall be 75 mm and the ends shall be 100 mm and all overlaps and joints shall also be sealed by torch application. for parapets, membrane shall be taken to a height of min 60 cm and then inserted inside the parapet in a groove. the same shall be finished by a membrane flashing. (iii) Coved fillet in PCC (1:2:4) tpe B0 of radius 75 mm shall be provided at the junctions of roof and parapet wall / mumty / chimney/ other vertical surfaces complete all as specified and directed.

M&L 75 mm thick PCC(1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for 25mm thick Sand cushioning under floors complete all as specified and directed.

M&L 60mm thick machine pressed precast conctete interlocking rubberized paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 , M-35 Grade complete all as specified and directed.

M&L Plain cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) set in cement mortar 1:4 as in kerb blocks with plain fair faces including chamfered weathering throating etc complete all as specified and directed.

Cutting holes in brick walls Exc half brick but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar etc for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 TYpe B1 as required complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) all as specified & as directed.

M&L for Precast RCC (1:2:4) type B-1 in manhole/soack well/septic tanks slabs/covers etc including necessary form work complete set in cement mortar 1:6 complete all as specified and directed.

M&L for RCC (Nominal mix ) in chajjas, kitchen shelves Type B1 1:2:4 (20mm graded stone) complete all as specified and directed.

Form work to chulla hoods ,chajjas,troughs ,kitchen slab and similar items including edges and fair finished surfaces complete all as specified and directed.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165 complete all as specified and directed.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even .The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation or for shafts, walls, manholes etc not exc. 10 Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and directed.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and directed.

Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete all as specified and directed.

M&L for 150 mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars including forming cradles all as specified & as directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment alongwith the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear meter incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors drilling and plugging holes etc all as specified and directed.

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment of soil under existing floor using chemical emulsion 300mm apart incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors using emulsion @ 1 litre per hole complete all as specified and directed.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around complete all as specified and directed.

M & L for writing letters or figures (Block, Roman, Itslic or Indian) n. exc 30 cm height with thick synthetic enamel paint. complete all as specified and as directed by Engr- in - Charge.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm/110mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 3/4" (20 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 3/4" (20 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 3/4" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 3/4" (20 mm) GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

S & F for Pipe Supporting Clamping - Single Pipe of dia 1/2" (15 mm) down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt R/M system running vertically with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket for 1/2" (15 mm) pipe having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 1/2" pipe, Wall distance 3" - 1 Nos. 2. U Bolt R/M for 1/2" (15 mm) GI / UPVC / CPVC pipe Dia. - 1 nos and 3. Justi Khilla 2 1/2" - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing no. : CE Jaipur Zone - Jaipur; TD/2022/102. Make : Shaivi or equivalent as approved by GE.

Treatment for sunken portion is as follows:- M&L for water proofing treatment in sunken floors as described hereunder:- 1) Demelotion of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. 2) PCC (1:2:4) type B0, covered filling in sunken portion 75mm thickness shall be provided at the junctions of RCC slab and adjoining walls. 3) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick plaster in CM 1:4 wixed with WPC@ 3% by weight of cement. 4) Applying bitumen primer of sunken floor & side surfaces TANKMASTIC of M/s STP Ltd @ 0.40 ltr/Sqm. 5) Sunken portion shall be filled with lean concrete (1:5:10), Type E-2 using 40mm aggregate after carring out of satisfactory testing of CIpipes/Joints & Slab/walls by filling water 72 hrs. The sunken portion of Nahani trap/floor trap and pipes, joints shall be emmbeded in PCC (1:3:6) blocks 6) GI Spout pipe 32mm dia and 450mm long cross cutted ends shall be inserted at the time of repair to Sunken portion as directed. Note:- i) In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. This process of grouting and testing shall be repeated till leakage/seapage/dampness is elimaneted ii) Horizontal flat area only measured. iii) Above aspets are deemed to be included in quoted rate.

Dismantling Asbestos Cement Corrugated or Semicorrugated in Roof covering complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:4 complete all as specified & as directed.

Extra over stone walling for hammer dressing to face stone and dressing of face, beds and joints as specified of random rubble walling with maximum depression on face from straight edge held against the dressed surface n.exc 20mm complete all as specified and directed.

M&L for preparation of newly plastered surface of wall & applying two coats of cement base paint over a coat of primer chalk whiting, complete as specified and directed.

M & L for preparation of old treated surfaces of walls, plastered or unplastered and applying one coat of cement base paint of approved shade/tint. complete all as specified and as directed by Engr- in - Charge.

M & L for brooming down old decorated surfaces of walls, plastered or unplastered including cornices, plasters etc and applying one coats of white wash complete all as specified and as directed by Engr- in - Charge.

M&L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, and eves board fixed with self tapping screws complete all as specified and directed.

M&L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tesile strength of 550 Mpa as in roof covering to wall, fixed with self tapping screws complete all as specified and directed.

M & L rolled sections as in main and cross beam, hip and jack rafters purlins where connected rafters and running rails and guides for sliding doors: fixed with angle cleats other connecting plates complete all as specified and directed.

S&F for steel work in tubular section for purlin/rafters etc including special shaped washer etc. complete using induction butt welded tubes conforming to I.S. 1161-1998 grade St- 240 complete all as specified and directed.

M & L for plate (plain or chequred channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement complete all as specified and directed.

M & L for preparation of old painted steel surfaces over 10 cm in width or girth and applying one coat of synthetic enamel paint on old painted surfaces, complete all as specified and as directed by Engr- in - Charge.

M&L For False Ceiling Complete With Armgyp-FB ceiling Tiles of Size 595x595,9mm thick (as approved by GE) fixed with and including galvanised iron Powder coated inverted 'Tee" or "L" section (Concealed GI frame Work) Suspended From Ceiling with provision of Galvanised wire 4mm dia and wall tapping screws including butterfly clips,hold down clips for fixing the board to frame complete all as per manufacturer's instruction,complete all as directed and specified.

M&L Plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in coping of brick masonry wall chajja including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified& directed by Engr-in-Charge.

Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduit and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor fire resistant low smoke and halogen (FRLSH) PVC insulated and unsheathed cable 1100 Volts grade confirming to IS-694 drawn through non metallic rigid PVC heavy duty conduit in concealed (min 20 mm external dia) but shall be increased as per actual site requirement in accordance with clause No. 19.125 of SSR Part-I ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling including 1.5 mm FRLSH PVC insulated unsheathed copper earth wire including sunken type sheet metal flush box electro plated of suitable size with modular cover plate of required module with frame for one light point controlled by one way switch including cutting chasis in stone/brick wall as required on site all as specified & directed. Note :- (a) The rates quoted by the contractor shall be deemed to be included the cost of cutting chases in stone/Brick wall and making good to the disturbed surfaces by matching the colour of wall/ceiling as per existing. (b) The rates quoted by the contractor shall be deemed to be included the cost of modular cover lplate with frame of required module, cost of sunken sheet metal flush box and no additional payment shall be made on account of the same.

All as per item No. 132.00 here-in-before but for one fan point controlled by one switch and regulator

All as per item No. 132.00 here-in-before but for one exhaust fan point/Fresh Air Fan Point controlled by one switch .

All as per serial item No. 132.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No. 132.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per item No 132.00 here-in-before but for one bell/buzzer point controlled by one bell push

All as per item No 132.00 here-in-before but for one light point controlled two, two way switches

All as per serial item No 132.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

All as per serial item No 132.00 here-in-before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

S&F modular switches piano type flat surface type, single pole, one way, 5/6 Amp, 230 Volts.

S&F modular switches piano type flat surface type, single pole two way 5 Amps 230 Volts .

S&F modular bell push flat surface type, 5 Amps 240 V complete all as specified & directed.

S&F modular bell buzzer, AC 230 volts single pole complete all as specified & directed.

S&F modular switches piano type flat surface type, single pole, one way, 15 Amp, 230 Volts.

S&F modular socket outlet flat surface type, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

S&F modular socket outlet flat surface type, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

S&F modular ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified.

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete including all as necessary fitting accessories complete all as directed. Make : Philips/Havells/Crompton

Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fixing sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar, 8 way, 240 Volts.

S & F MCB 32/40 Amp, single pole & neutral,240 Volt complete all as pecified & directed.

S & F MCB 6-40 Amp, single pole 240 Volt complete all as pecified & directed.

Supply and fixing Vertical sheet metal enclosures double door type , suitable for fixing MCB, TPN with 200 amps rated bus bar , 4 way. 415 Volts with inbuilt MCCB 4 pole 63 Amp,16 KA

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed. Note : - Quoted rate shall be deemed to include for earth wire with protection pipe up to 7.5 meter length.

Disconnecting form elect connection and taking down carefully the existing electric energy meter of any capacity, any make,any size and depositing same the electric energy meter in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same inside the Old Meter Box carefully incl necessary electric connections complete all as directed.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing same the Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Geyser carefully incl necessary electric connections complete all as specified and as directed by Engr-In-Charge

M/L for GI pipe (Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore complete all as specified and directed.

Supply and fix ceiling fan complete with electronic type regulator, copper winding and accessories 230v 1200mm sweep BEE 5 star rated with brushless direct current motor (BLDC) including taking down old unserviceable ceiling fan complete all as specified and directed by engineer-in-charge.

S&F in repair cubical metallic box of size 1.00m x 0.90m x 0.30m depth made out of 2mm thick mild steel sheet, front openable, double door with locking arrangement with & including 3mm thick plain sheet clear glass of suitable size fixed to facilitate meter reading, all internal & external steel surfaces painted with two coats of synthetic enamel paint over a coat of red oxide primer, internal wiring with PVC insulated single core multistranded copper conductor FRLS cables IS-694 marked of adequate size but not less than 6 sqmm with proper ferrule & cable gland, box shall be fixed on wall with ‘Anchor’ type /fastener type bolts & nuts (Set of 6 bolts of 12mm dia 200mm long with nuts & washers) grouted into the wall properly to hold the box, writing MES No/Qtr No for each energy meter with thick white synthetic enamel paint, Neoprene rubber gasket shall be provided for proper sealing, box shall have arrangement for fixing electric energy meters – 04 Nos, MCB DB TPN 4 way -01 No complete all as directed.

S&F exhaust fan heavy duty metal body with copper winding motor of 120 watt, AC single phase 230/240 V of size 300 mm sweep with louver including making suitable opening/hole in wall all as specified and directed by ebgineer-in-charge

S&F Fresh air fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 MM complete all as specified and directed by Engr-In-Charge

shiva construction (BID ID -3438059)

Radha Enterprises (BID ID -3432364)