SPL REPAIR TO BLDGS NO T-274(SINGLE JCOS ACCN) AND T-60(SINGLE OFFICER ACCN) AND PROVN OF SHED AT FRONT ENTRANCE OF OF STN HQ AND TILLING WORK INFRONT OF OUTER SIDE WALL OF BLDG NO P-06 AGE B/R-I UNDER GE(N) BIKANER

Amount

Dismantling Asbestos cement Corrugated sheets in roof covering including ridges .

Dismantling of existing false ceiling of boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

M&L for pre painted galvalume aluminium zinc cozting GI based corrugated steel Sheet high rib profile tile pattern of slaty color coated 0.5 mm thick of 550 Mpa Tensile strength sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd )

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel designer ceiling pre finished conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster)

Taking down cement plaster/terrazo finish on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed

M&L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement using integral liquid water proofing compound and complete. Note : WPC shall be measured and paid seperately.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick wall care putty on new surfaces including preparation and complete specified and as directed by Engineer in charge.

M&L for Preparing new /old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall care putty complete and as directed by Enginner in charge.

Supply only liquid water proofing compound ISI marked @ 200ml per 50Kg of cement content.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed.

M&L for 75mm thick Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, , finished even and smooth using extra cement , laid in panels including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete.

M&L for Double charge/ultra charge vitrified tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.18 sqm not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match floor including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes complete all as specified and directed by Engineer-In-Charge.

M&L for Double charged Virified/ultra charge Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match floor including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes complete all as specified and directed by Engineer-In-Charge.

Ditto all as above item No 14 but as in skirting over 10 mm cement screed bed backing ( 1:3) complete all as specified and directed by Engineer - in - Charge.

Ditto all as above item No 15 but as in skirting over 10 mm cement screed bed backing ( 1:3) complete all as specified and directed by Engineer - in - Charge.

M & L for non skid ceramic colour (light shade) joint free tiles with matt finish size 400x400x7mm thick ( square/ rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed over Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes confirming to IS-15477:2004 including necessary cutting as per site requirement complete all as specified and directed by Engineer - in - Charge.

M & L for glazed ceramic tiles (coloured) 450x300x7mm/ 350x250x7mmthick on vertical surfaces such as skirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick rendering in Cement Mortars 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed.

Dismantling of floor hearth or existing terrazo dado /flooring or tilles in bath .WC and kitchen /kota stone etc as directed by Engineer in charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified

S&F vitreous china premium/1st quality wall hung water closet with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified. Make : Jaquar (Continental Series-CNS-WHT-963N or equivalent from Parryware/Hindware as approved by GE

S&F concealed flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and 'S' type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and and taking down existing of any description/size complete in all respect all as specified. Make : Jaquar (Concealed Cistern-JCS-WHT-2400S, Flush Plate-JCP-CHR-812415) or equivalent from Hindware/Parryware as approved by GE

S&F health faucet with 8mm dia and 1.2 metre long flexible tube in chorme finish and wall hook including making connections and fixed in position complete in all respect as specified. Make : Jaquar (ALD-573) or equivalent from Hindware/Parryware/Cera as approved by GE

S&F in repair vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including S&F all accessories as recommended by manufacturer and incl. brass CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified. Make : Hindware (WHB-Garnet (Cat No.- 10080), Waste Coupling-Cat No.- F850023 (Economy Model), Bottle Trap-Cat No.- F850072 (Economy Model) or equivalent from Jaquar/Parryware/Cera as approved by GE

S&F single lever central Hole Basin Mixer 15mm bore dia with letter marked for cold and hot complete

S & F in repair brass chromium plated bib cock long Nose body Fancy type with capstan screwed down for iron pipe 15 mm bore complete all as specified & directed.

S & F in repair angle valve cock chromium plated fancy type half/full turn for iron pipe 15 mm bore screwed down high pressure, with capstan head, screwed both ends for iron pipe or for union complete all as specified & directed.

S& F single lever High concealed diverter flow consisting of exposed part kit with operating lever , wall flange & button and concealed body ,cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure all as specified make Cera:(exposed part F1018721, concealed part F4030101, bath Spout F1020661), Jaquar or equivalent in same Pattern

S & F repair PVC connection 15 mm size brass nuts of length 450 mm complete all as specified & directed.

Taking up or down steel tubing and connections 15 mm bore complete all as specified and directed by engineer in charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store as directed complete.

Supplying and laying of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, wall complete all as specified.

Supplying and laying of CPVC pipes of 25 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, walls complete all as specified.

S&F male/female brass threaded adaptor(FTA/FBTA) complete all as specified

S&F in repair triple layer Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, hoisted and fixed in position including all necessaries fitting connecting up pipes complete.

S&F in repair triple layer Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixed in position including all necessaries fitting connecting up pipes complete.

S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms) complete.

S & F in repair gun metal glob or gate valve with iron wheel head , crewed for iron pipe of 20 mm dia fixed in repair complete all as specified & directed.

S&F in repairs Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete.

S&F SS folding Tubular towel rack, 20mm dia, , 60cm long between flangess including all accessories complete all as specified and directed by engineer in charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge..

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules ofelasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). → Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed .

All as per item No-45 above but single extruded & size of WPC Chowkhat/frame of size 65 x 125mm ditto

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (Table 6 of BIS 12817-2020) BIS marked. (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf as per table 1, dia of bolt 12mm as per BIS 15833. (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf, 16mm dia as per BIS marked clause 3(iii) of BIS 15834-2020. (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/gauge skelton door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws including S&F of stainless steel 304 Grade (natural finish) wire cloth, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (Table 6 of BIS 12817-2020) BIS marked. (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf as per table 1, dia of bolt 12mm as per BIS 15833. (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf, 16mm dia as per BIS marked clause 3(iii) of BIS 15834-2020. (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf (f) Stainless Steel (304 Grade) wire cloth fixing as per manufacture (g) Stainless Steel (304 Grade) 300 mm, ordinary rat tail rod pattern springs-01 nos

S&F of Powder Coated aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Powder Coated aluminiuml butt hinges pin anodised and fixed ,type B-21 of 100mm.

S&F for 150mm size Powder Coated aluminium barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F for 150mm size Powder Coated aluminium handle of febricated type and fixed.all as specified and directed.

M & L for preparation of new/old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed.

M&L for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and complete.

Demolition of brick work built in cement mortar including all quions arches pillars etc

M&l for brick work with sub class B bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6.

S& F chromium plated soap dish Holder with round flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer in charge.

S&F Corner glass shelf of size 300mmx200x150mm fancy type, toughned glass, with CP bracket and guard railing, fixed along wall with CP brass screws and PVC plug complete all as specified and as directed.

M&L for 25mm dia stainless steel chromium plated curtain rod incl bracket & knobs fixed in position .

Anti termite treatment of soil under existing floor using chemical emulsion one litre per hole, 300 mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed.

Anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron all as specified.

Supply and Fix 5mm thick Figured glass, pin head type and glazing with beads (either supplied with shutters or to be measured separately as supply only) in squares not exceeding 0.5 Sqm in each pane incl rubber gauscet complete.

Supplyand fix 4.80mm thick Sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane incl rubber gauscet complete all as specified

Removing building materials etc. i.e broken construction material, plaster and like to a distance of 7 km at a suitable location specified by Engineer-in-charge

Mild steel framed work such as grills, gratings, tank staging etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks, cooler stand and similar work conforming to Fe 290 Gd E-165 all as specified .

M&L steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-In-Charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length and length of bolt exc 30 cm long with dia of neck exc 12 mm (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

S&F plates (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement complete all as specified.

M&L for mild steel work as in plates / flats angles/40mmx3mm falt iron as in wind ties for roof etc as in cleats drilling welding etc

S&F PVC (SWR) 110mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) vent cowl for 75mm dia pipe all as specified.

S&F PVC (SWR) diminishing pieces or tapers/ Reducers/ Sockets 110 mm bore fitted with oval access door. all as specified.

S&F PVC (SWR) bends any radius 75 mm fitted with oval access door. all as specified.

S&F PVC (SWR) bends any radius 110mm fitted with oval access door. all as specified.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. .

S&F 50mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. .

S&F stack clamps out of 100mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100mm/75mm bore pipe complete all as specified and directed. .

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F stain less steel peg set with 06 no of hooks mounted on SS plate 4 mm thick with and including screws

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in loose/soft soil complete.

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete (reinforcement to be measured separately)

M&L for TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirallyfor hooping for columns, hooking ends and binding with and including ms wire (annealed) nit less than 0.90 m dia or securing with clips complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia150mm, set in cement mortar complete.

M&L for Cement concrete 1:3:6 type C2 Concrete bed(width of bed is outer dia of pipe plus 30 cm) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested

M&L for DWCPE (SN8) confirming to IS-16098,150 mm Nominal bore (160 mm OD) complete laiding and jointed incl testing along with necessary jointing material tees /union /socket etc complete as per manufacture instructions and complete all as specified and directed.

Cutting into existing manholes for connecting new drains, 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in lean concrete foundation.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

Surface excavation in soft /loose soil not exceeding 30cm deep and average 15cm deep and getting out all as specified & directed

Material and labour for 75mm thick hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in- charge.

M&L 100 mm thick PCC 1:4:8 type D-2 as in sub base

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;

S & F flats angles/40mmx3mm falt iron as in wind ties for roof encluding securing bolts/srews etc

Excavation in post holes (or similar holes) in loose/ soft soil each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exeeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as spcified and directed.

Taking down old U/S existing DB SPN 8 way & TPN DB 4 way including MCB/MCCB/Sheet Metal enclosure plug socket of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

Disconnecting and taking down unserviceable submain wiring form TPN DB to SPN DB and SPN DB 8 way to SPN DB 4 Way complete & removing U/S items from site complete all as directed by Engineer-in-Charge.

Taking down the old unserviceable Fan regulator from site complete all as directed by Engineer-in-charge.

Taking out carefully earthing set complete of any type including earthing wire & removing U/S items from site complete all as directed by Engineer-in-charge. complete all as specified and directed by Engineer-in-charge.

(b) One multi pin socket 5/6Amps, Independent.

(c) One 5/6 amp socket outlet on the same board controlled by another switch.

All as per item No 102 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.5 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 2.5 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .

All as per item No 102 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .

S&F switch Modular type, 5/6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 15/16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F socket outlet 3 Pin 5/6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

.S&F socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified.

Taking down Ceiling fan,sealing cable end, dismantling blades of any make, any sweep, and refixing after necessary repairing such as winding of motor, replacement of capacitor & ball bearing of ceiling fan, cleaning all dust & painting with existing colour synthetic enamel paint by spraying including filling cavities with filler,one coat including writing MES No. all as specified and directed by Engr-in-charge

Supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300 mm sweep with blades and frame including new mosquito stainless steel wire mesh of gauge 0.36 mm with suitable wooden fram eprotection against birds etc including provision of cutting of existing wall for suitable opening as per fan including electric connection with & including new 1.5 Sqmm 2 core flexible copper conductor cable from ceiling rose to fan,fan hanging on wall with 04 Nos steel fastners 10 mm dia 100 mm long and making good disturbed surface with cement mortar complete all as specified and as directed by Engineer-in-charge. Note : (i) Serial no as issued by Engineer-in-Charge of Exhaust Fan and GE Office name shall also be written on Exhaust Fan with red colour permannet marker,cost for the same shall deemed to be included in the quoted unit rate nothing shall be paid extra on this account. with blades and frame including new mosquito stainless steel wire mesh of gauge 0.36 mm with suitable wooden fram eprotection against birds etc including provision of cutting of existing wall for suitable opening as per fan including electric connection with & including new 1.5 Sqmm 2 core flexible copper conductor cable from ceiling rose to fan,fan hanging on wall with 04 Nos steel fastners 10 mm dia 100 mm long and making good disturbed surface with cement mortar complete all as specified and as directed by Engineer-in-charge. Note : (i) Serial no as issued by Engineer-in-Charge of Exhaust Fan and GE Office name shall also be written on Exhaust Fan with red colour permannet marker,cost for the same shall deemed to be included in the quoted unit rate nothing shall be paid extra on this account.

Taking down LED tube light fitting, 1x 20 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Refixing LED tube light fitting, 1x 20 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engr-in-Charge.

S&F LED Bulb 9W, operating voltage- 220-240 volts, starting time < 0.5s, color temperature-6500K, lumens: min 825 complete all as specified and directed by Engineer-in-charge.

Supply and fixing LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-Charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB TPN DB 4 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S& F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB TPN 40-100 Amps, 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S&F in of sheet metal enclosures with socket, plug top complete with one single pole MCB -240 Volt- 20 AMP complete all as specified and as dircted by Engr-in-charge. Note : For AC Point.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

M&L for Sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 cm spread thickness (8 cm in depth before laying the cable and 15 cm in depth after laying the cable) and consolidated (punned) upto 180 mm thickness, complete all as specified and as directed. Note : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for.

Supplying and laying un-reinforced precast concrete cable cover, class LV,type 1 with flat size 250 mm x 150mm x 40mm complete all as specified and as directed by Engr-in-Charge.

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 4 core x 25 Sqmm complete all as specifed and as directed. Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 100 mm dia suitable for 0.4 mpa working pressure

S&F GI tubing light grade 40mm dia for protection of cable on pole/ wall etc complete all as specified and as directed by Engr in charge.

Supply, laying and jointing GI tubes, medium grade40mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Supply, laying and jointing GI tubes, medium grade 20mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in walls/under floors complete all as specified and directed by Engr-in-charge.

Cutting existing steel tubing for alterations or additions done in position without taking down for 10mm to 40 dia pipe (Each cut measured)

S&F Gun metal gate valve 40 mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed for the following sizes-

S&F Gun metal gate valve 15mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .

Materal and labour for construction of brick masonary valve pit chamber of size 900x900x600 mm (Internal dimension) using sub class ,B, bricks complete, earth work, PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation, brick masonary sub class bricks 23 cm build n cement mortar and below ground level PCC with 1:2:4 type B2 using 20mm grade stone aggregate, copng 50 mm thick including frame of size 75x75x6mm made of angles iron and chamber cover made of MS sheet of 4 mm thickness double leaf including MS hinges locking arrangement with provision of locks and keys, painting of the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer including necessary excavation, returning & filling & removing of surplus soil etc complete all as specified and as dircted by Engineer in Charge.

N.K. CONSTRUCTION COMPANY (BID ID -3478657)

M/S ASHRAFI CONSTRUCTION CO (BID ID -3478499)

Beenu Co. Company (BID ID -3483549)

A.S. CONSTRUCTION COMPANY (BID ID -3484285)

BIG B CONSTRUCTION (BID ID -3478643)