SPECIAL REPAIR TO BLDG NO. 358 (YOS BLOCK) AT CME

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm but not exc. 4.0 sqm each all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm but not exc. 4.0 sqm each all as directed.

S & F 2nd class hard wood plain solid straight chowkats and frames, wrought, framed rebated on the soild rounded or chamferred, put together with glue pinned at joints all as specified and directed.

Taking down shutters only of sizes exc. 1.00 sqm but not exceeding 4.00 sqm all as directed.

S & F 30mm thick flush shutter, solid core construction with block board core and both face is covered with decorative face veneer with lipping/ frame to match complete all as specified and directed.

S & fixed 2nd class hard wood 35 mm thick factory made glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified and directed.

S & F Mild steel works as in bands, straps, hold fasts etc. conforming to IS-2062-2006 (fe-290), embedded portion duly painted with bituminous paint and sanded complete all as specified and directed.

M & L preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc. 0.1 sqm each treated with tar or coal tar black paint complete all as specified and directed.

M & L Cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and directed.

M & L for preparing new wood and wood based surfaces of any description, over 100mm width or girth and applying two coats of synthetic enamel paint (First quality) over a coat of pink primer, complete all as specified and directed.

S & F PVC solid door frame of size 50x47mm made out of 5.0mm plain colour PVC sheet reinforced with mild steel square tube as specified manufacturers instructions complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (Stile) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rails & bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement and fixing in the frame at site as per specifications and drawings, complete all as specified and directed.

Dismantling wrought iron or mild steel work, viz. mild steel flat iron, mild steel bars, bends, straps and similar work including mild steel bolts, nuts etc. fixing to RCC fencing posts, struts etc. complete all as specified and directed.

S & F for framed work such as grills or grating etc with ends of bars shouldered as framed guard bars conforming to Fe-290 Gde E-165 complete all as specified and directed.

S & F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) quality A complete all as specified and directed.

M & L for preparing old wood and wood based surfaces of any description, over 100mm width or girth and applying one coat of synthetic enamel paint (First quality) complete all as specified and directed.

M & L preparing new steel and iron surfaces of any descriptions, over 100 mm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

M & L preparing old steel and iron surfaces of any descriptions, over 100 mm in width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

S & F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 150 mm mild steel pressed handles, oval type, stove enamelled black all as specified and directed.

S & F 300mm mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed all as specified and directed.

S & F 150 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed tinned tacks of mild steel wire staples, fixing etc. complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed tinned tacks of mild steel wire staples, fixing in repair etc. complete all as specified and directed.

S & F in repair 150mm dia double legged door stopper of aluminium alloy with rubber complete all as specified and directed.

S & F for powder coated aluminium anodized three track sliding window with two or more shutter with 4 mm thick plain glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock, etc. rubber beading and glazing clips etc using following sections as given in 'JINDAL' catalogue including taking down existing old window of any description complete all as specified and directed. Note: Size of aluminium sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605.

S & F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc. including taking down existing old window of any description complete all as specified and directed.

S & F aluminium powder coated fixed partition with frame of size 101.6mm x 44.45mm x1.27mm thick and 101.60mm x 44.45mm x 1.20mm thick with total height 3.20m. The panels shall be made out of 5mm thick plain/ tined (frosted) glass in top & bottom of 12 mm thick both side laminated particle board (i.e. 50-50) including door with accessories i.e. floorspring, hydraulic door closer, butt hinges, handle tower bolt, necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screw etc. including making good to the disturbed portion complete all as specified and directed.

M & L for 20mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc. complete all as specified and directed.

Rounding to edges of stone slabs, such as in steps, cooking platform and other similar situation complete all as specified and directed.

M & L 15mm thick cement plastering on block/stone masonry surfaces in CM 1:4 finishing the surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surface etc. including raking out joints, hacking for key scrubbing down with water complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation boards/ slabs/ blankets) any thickness, including cover fillets complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.60 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x 38mm x 0.7mm cross tee of size 24mm x 28mm x 0.7mm using purpose made members interlocking to each other and with 40 mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc. all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacturers instruction make of GI grid work : Armstrong/ swastik/ Techno grid and make E board Gypsum or equivalent approved.

S & F in repair 12 mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces, fixed with screws to timber frame work. Make : Duro/National

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for 75 mm thick PCC type D-2 (1:4:8) using 40 mm graded stone agggregate as in sub base etc. complete all as specified and directed.

M & L for 25 mm thick, type B-1, 1:2:4 (20 mm graded stone aggregate) as in sub base etc. complete all as specified and directed.

M & L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6 all as specified and directed.

S & F light shade Vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed.

S & F coloured Non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed.

S & F light shade Vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting, dado, risers of steps and pillasters etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. complete all as specified and directed.

M & L for rendering 10 mm thick cement mortar in 1:4 as backing coat for fixing wall tiles complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surface, 350 mm x 250mm x7mm/ 450mm x 350mm x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L 75mm PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection including necessary use and waste of formwork complete all as specified and directed.

M & L Hardcore using broken stone boulders not exceeding 63mm deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

Raking out joints/ pointing to random or polygonal rubble uncoursed or brought upto course built in cement mortar complete all as specified and directed.

M & L raised pointing to random or polygonal rubble, uncoursed or brought upto course in CM 1:4 including necessary scaffolding upto all floor complete all as specified and directed.

Dismantling tiling of single layer mangalore pattern roof tile laid dry complete all as specified and directed.

All as per item No.50 above, but bedded in lime or cement mortar complete all as specified and directed.

M & L for roof tiles, mangalore pattern, interlocking at side joints laid dry complete all as specified and directed.

All as per item No.52 above, but except tile complete all as specified and directed. Note :- Serviceable tiles obtained from sl item No. 50 shall be re-used in this item.

M & L for ridge tiles, mangalore pattern, set and jointed in CM 1:6 complete all as specified and directed.

All as per item No.54 above, but excpet mangalore pattern ridge Note :- Serviceable tiles obtained from sl item No. 51 shall be re-used in this item.

Dismantling batten for tiles, shingles etc. of any size including tilting fillets spacing exc. 15 cm complete all as specified and directed.

M & L 2nd class hardwood clean sawn battens at 30cm centres of sectional area exc. 5 & not exc. 15 sqcm complete all as specified and directed.

All as per item No.57 above, but except batten Note :- Serviceable tiles obtained from sl item No. 56 shall be re-used in this item.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete all as specified and directed.

M & L 2nd class hardwood clean sawn in scantling fixed in framed work complete all as specified and directed.

Dismantling boarding, any description in any position with nails complete all as specified and directed.

M & L 2nd class hardwood clean sawn weather boarding, plain, 20 mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps complete all as specified and directed.

M & L for preparing the surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treated with two coats of cresote oil complete all as specified and directed.

M & L for preparing the surfaces of tiles batten any size and spacing prepared and treated all over (measured overall on one side only), spaces not deducted with two coats of cresote oil complete all as specified and directed.

S & F in repairs 15mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees, union etc and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F in repairs 20mm dia steel water tubing medium grade galvanized with and including all fittings such as bend, tees, union etc and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Cutting chase, pinning in making good to facings where required & pointing in cement mortar 1:3 to ends etc. or edges of landings, steps cills, sunshades, shelves, lintels etc. and cutting chases for concealed water tubing and making good, cutting not exc. 10 cm girth in brick wall as directed.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premisses complete all as specified and directed.

S & F in repair 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring, joints fixed to walls complete all as specified and directed.

S & F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring, joints fixed to walls complete all as specified and directed.

S & F in repairs 110 mm dia PVC (SWR) bends any radius, provided with access door complete all as specified and directed.

S & F in repairs PVC (SWR) branch pieces, single (single 'Y') equal or unequal, 110 mm bore provided with access door complete all as specified and directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal 110mm bore, provided with access door complete all as specified and directed.

S & F in reparis 75 mm dia PVC (SWR) bends any radius provided with access door complete all as specified and directed.

S & F in repairs PVC (SWR) branch pieces, single (single Y) equal or unequal, 75 mm bore, provided with access door complete all as specified and directed.

S & F in repairs PVC (SWR) junction single (single T) equal or unequal 75mm bore, provided with access door complete all as specified and directed.

Demolition of brick or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L precast solid block masonry of block in precast cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed.

M&L 15mm thick cement plastering on brick/block masonry surfaces in CM (1:4) finishing surfaces even and fair without using extra cement complete all as specified and directed.

M&L 15mm thick cement plastering on stone masonry surfaces in CM (1:4) finishing surfaces even and fair without using extra cement over and including 10mm thick dubbing out on irregular face of wall in CM 1: 4 complete all as specified and directed.

M&L preparing newly plastered surfaces of wall and applying complete wall with POP/wall putty for making smooth surfaces and applying two coats of 100% acrylic emulsion paint over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces ceiling and applying complete ceiling with 3mm POP putty for making smooth surface and applying three coats of white wash all as specified and directed.

M&L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth with sagol all as specified and directed.

M & L for complete scraping down of old decorative surface of walls with steel wire brushes of smoke spots, moulds, moss efflorecent salts and applying complete wall with 3mm POP/wall putty for making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L preparing newly plastered surfaces of wall and applying complete wall with POP/wall putty for making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed.

M&L for preparation of old plastered surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

S & F in repair table top wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste fittings union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed. Make : Hindware Cat No. 10065 or equivalent model in Cera /Parryware/ Neycer as approved by GE.

S&F in repair viterous china wash down water closet pan (pedestal pattern) white (including fixing bolts, flushing cistern and flush pipe) including provision of flush pipe, plastic seat cover for pedestal pan and cp health faucet including two way angle cock complete all as specified and directed. Make : cera

S&F in repair brass chromium plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specified and directed.

S & F in repair brass chromium plated, 15 mm bore health faucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and directed.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F decorative cabinet looking mirrior necessary fixing arrangement complete all as specified and directed.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia , D type 60cm long between flanges complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stainless steel bracket guard and railing 60 cm long etc. complete all as specified and as directed.

S&F in repair 15mm dia concealed stop valve chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed.

S& F in repair stainless steel Soap dish holder complete as specified and directed. (make: Jaquar or equivalent)

S&F in repair stainless steel Toilet paper holder, of make Jaquar or equivalent

S& F in repair Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed all as specified and directed.

S&F in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair overhead shower 100mm dia round shape single flow (ABS body chromium plated with grey face plate) with Rabit cleaning system complete fixed to ceiling complete all as specified and directed. Make : Jaquar Cat No. DHS-1989 or equivalent approved

M&L cement concrete type E-2, 1:5:10 (40 mm graded stone aggregate) lean concrete as in sunkun floor for filling etc. complete all as specified and directed.

M&L 40mm thick cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in sunkun floor complete all as specified and directed.

M&L 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

Supply only WPC all as specified and directed.

M & L for complete removal of existing treatment from walls, filling the holes/cavities and plastering the surface required, cleaning and preparation of the surfaces and applying complete wall with 3mm POP/wall putty for making smooth surfaces and applying two coats of exterior emulsion paint 100% acrylic over a coat of primer as per manufactured instruction complete all specified and directed. Note : The rate shall be quoted by the contractor including scafolding to carry out the work for height more than 10.00 mtrs.

M&L bitumen blown any grade applied hot, two coats to concrete surfaces at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

M&L Polythene film black 50 micron laid in floor complete all as specified and directed.

S& F in repair Wash hand basin mixer complete all as specified and directed. by Engr-in-Charge. (make : Jaquar or euivalent approved by GE)

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately.

M&L for point wiring with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/caping with all accessories and 1.50 sqmm green in colour PVC copper conductor FRLSH cable for earth continuity connected to common earth dolly incl PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators, etc complete all as specified and directed for one light/fan /bell point controlled by one switch & making good to disturbed surface of wall etc for the following :-

One light point controlled by one switch

One fan/exhaust fan point controlled by one switch and regulator

Socket outlet, three pin 5 Amps on the same board

Socket outlet, three pin, 5 Amp, independent

All as per item No.111 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity for multipin 15 amps socket outlet flush type on independent board.

S & F switch piano, flush type, single pole one way 5 amps complete all as specified and directed.

S & F switch piano, flush type, single pole one way 15 amps complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 amps flush type complete all as specified and directed.

S & F socket outlet 5 in 1, 5 pin, 15 amps flush type complete all as specified and directed.

S & F bell push flush type single pole one way 5 amps complete all as specified and directed.

S & F ceiling rose, 3 terminal PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed.

S & F lamp holder, PVC/polycarbonate type with back plate suitable for batten fitting incl PVC square block complete all as specified and directed.

M&L in replacement of LED lamp 9 watt complete all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed.

S & F in replacemnet Call bell ding dong AC, 230 Volts, single pole complete all as specified and directed.

S&F surface and wall mounted LED batten(LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 No PVC square blocks incl taking down old UNSV fitting. Make- Havells cat No LUMILINEBS20WLED830SPCWH or equivalent of Philips/ Bajaj/ Crompton Greaves/ Wipro/ Shakti/ Halonix/ Jaquar/ C & S / Bentec India Ltd./ Luker.

S & F Decorative ultra slim with polycarbonate housing with high lumen output environmental friendly, energy efficient ready to use pack surface and wall mounted LED batten(LED tube light fitting complete 10W) with integrated electronic driver and 02 No PVC square blocks incl taking down old UNSV fitting. Make: Philips/ Bajaj/ Crompton Greaves/ Wipro/ Shakti/ Halonix/ Jaquar/ C & S / Bentec India Ltd./ Luker.

S&F building security LED light fitting 25 Watt , energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 including suitable size bracket incl taking down old UNSV one. Make:- Havells cat No. ENDURASUNDOWNSL25WLED765PASYBOPCIHD or equivalent of Philips/ Bajaj/ Crompton Greaves/ Wipro/ Shakti/ Halonix/ Jaquar/ C & S / Bentec India Ltd./ Luker.

S & F PVC cable ducts 75 x 45 mm with all accessories for fixing of sub main wiring drawn through cable duct along wall complete all as specified and directed.

M&L for sub main wiring with two run of 6 sqmm single core multi stranded PVC insulated and unsheathed copper conductor of grade 1100 volt FRLSH cable in and including 1100 volt electrical grade PVC Conduit of desired colour not less than1.2 mm thick and 25 mm wide & 6 sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one.

S&F in replacement enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps, 240 volt all as specified and directed.

Taking down ceiling fan of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling greasing etc including providing flexible three core from ceiling rose to connector of fan all as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm all as specified and directed.

S&F in repairs load line vertical TPN distribution board 4 way including 1 incommer MCCB of 125 Amps 4 pole double door IP-43 protection, powder coated, IK08 with provision of suitable size bus bar and cable management kit complete all as specified and directed. Make : Indoasian cat part No 811888 or eqlnt in Hager/ Havells/ Legrand

M & L in replacement MCB distribution board double door 415 volt, TPN 4-way, all as specified and directed.

S & F in replacement MCB distribution board Double door SPN 240 volts 8 way with 200 amps rated bus bar and making good to disturbed surfaces of floors walls etc all as specified and directed.

S & F in replacement MCB SP 6 to 32 Amps, 230 V AC complete all as specificed and directed.

S & F in replacement MCB SPN 40 to 63 Amps, 230 V, AC complete all as specificed and directed.

S & F in replacement MCB TPN 100 Amps,415 V, AC complete all as specificed and directed.

M&L for earthing complete with GI earth plate electrode 60x60cmx6mm thick burried directly in ground in earth pit not less than 2.25 mtr depth below normal ground level with top edge of the plate vertically to depth of not less than 1.5 mtr below ground level connected to & including GI lead 4 mm dia as earthing lead connecting to equipment by means of GI bolts & nuts etc with provision of charcoal and salt etc all as per electrical plate No-3 of SSR part-I 2009 including RCC cover and MS angle iron frame, watering with GI pipe 20 mm dia (medium grade) & MS funnel, concrete pit including excavation and earthwork in any strata returning filling in and removal of surplus soil and testing on completion etc. complete all as specified and directed by Engineer-in-charge.

Taking down electric water heater (Geyser) of 25/50 litres capacity and refixing the same after repair alongwith connected accessories such as PVC connection pipe, fastner etc. complete all as specified and directed. Note :- cost for spare parts for repair of geyser is deemed to be included in the unit rate quoted.

N AND G CONSTRUCTION

vishalconstruction

Sunrise Traders

Mukund Engineers and Contractors

ShreHari Civil Enginneering and Contractors