SR (MC and EW) for illumination of Laxman Temple, Sirpur, Village- Sirpur, Distt-Mahasamund

Amount

Provision for providing and fixing of energy efficient, environment friendly, long life, exclusive innovative designed RGBW projector light with 150W having 25- degree beam angle, digitally designed based on DMX 512 protocol to obtain the desired color combination out of 16 million colors, suitable for architectural and heritage illumination; operating temperature: -20°C to +50°C, operating voltage range: 100V to 300V AC, ingress protection IP66, impact resistance IK07, average life L70B50: 50000 hours; luminaire constructed with pure polyester powder coated aluminum die-cast housing in grey finish featuring aesthetically contoured heat sink for efficient thermal management; integrated with built-in potted IP67 electronic LED driver incorporating Active Power Factor Correction (APFC), lower Total Harmonic Distortion (THD), open circuit protection, over voltage protection, surge voltage protection up to 10kV with SPD, and tested for compliance with IS 15885 Part-2/Sec 13 and IEC 60598-1 standards; additionally equipped with high-level waterproof IP67/IP68 and VDE/UL approved nylon connectors molded with cable for carrying DMX signal from DMX controller to fixture or between fixtures without signal loss or noise generation; including adjustable stainless steel mounting brackets, tamper- proof hardware, and provision for earthing and surge protection as per site requirement along with necessary accessories for fully functioning like DMX MALE/Female SUPPLY CABLE 1M 4 PIN, DMX EXTENSION CABLE1M/3M 4 PIN as directed by engineer incharge

Provision for providing and fixing of energy efficient, environment friendly, long life, exclusive innovative designed RGBW projector light with 90W power rating and a 10-degree beam angle, digitally designed based on DMX 512 protocol to obtain the desired color combination out of 16 million colors, suitable for precise architectural or monument highlighting applications; operating temperature range: -20°C to +50°C, operating voltage range: 100V to 300V AC, with ingress protection rating of IP66 and impact protection IK07, average life L70B50: 50,000 hours; constructed using pure polyester powder coated aluminum die-cast housing in grey finish with an aesthetically engineered heat sink for advanced thermal management; integrated with a built-in potted IP67 electronic LED driver featuring Active Power Factor Correction (APFC), lower Total Harmonic Distortion (THD), Open Circuit Protection, Over Voltage Protection, and Surge Voltage Protection up to 10kV with SPD, conforming to IS 15885 Part-2/Sec 13 and IEC 60598-1 safety standards; equipped with high-level waterproof IP67/IP68-rated VDE/UL approved nylon connector molded with cable to transmit DMX signals seamlessly from controller to fixture or between fixtures without signal loss or noise interference with necessary accessories for fully functioning like DMX MALE/Female SUPPLY CABLE 1M 4 PIN, DMX EXTENSION CABLE1M/3M 4 PIN as directed by engineer incharge

Provision for providing and fixing of Retro look post top which delivers excellent illumination & comfort, Long life &photo biologically safe LED’s, High performance electronic driver ensures, zero maintenance, No harmful UV & IR radiations, Environment friendly as it does not contain Mercury, Instant light with low running temperatures, Operating temperature: -10°C to +35°C, Operating voltage range: 140-270V, Average life L70B50: 50000 hours, Elegantly designed die-cast aluminum housing with heat sink for efficient thermal management sturdiness and excellent corrosion resistant Al. canopy with classic design to enhance the aesthetic of the fixture. Two nos. die-cast aluminum arms & AL. Die cast Spigot are provided to support the housing.70W, IP65,IK07 with Epoxy powder coated black after phosphochromate treatment, High quality UV Stabilized poly carbonate opal cover is used over LED module to provide glare free Light, Powered by built-in, isolated potted electronic LED driver with APFC (SMPS based constant current supply) with lower THD, Output Short/Open Circuit protection, Over Voltage protection, Surge Voltage protection up to 10kV with external SPD & other reliability test as per IS 15885 Part-2/Sec 13 along withnecessary accessories as directed by engineer incharge

Provision for providing and fixing of stand-alone DMX 512 controller capable of managing a wide range of DMX systems from basic RGB/RGBW to advanced moving lights, color-mixing luminaires, DMX-enabled audio players, and fountains, featuring dual-channel DMX output with real-time clock (RTC), calendar-based scheduling, multi-zone programming, dry contact trigger ports, and SD card memory, programmable via Havells DMX software on PC and fully integrable with Smart LitM DMXC platform for seamless control / USB-C protection along with necessary accessories as directed by engineer incharge

Provision for providing DMX lighting system programming and commissioning through a certified professional, including customized light design configuration, scene setting, and synchronization as per site-specific requirements, ensuring full functionality and compatibility with installed DMX-compatible fixtures.

Supplying and laying ISI marked double wall HDPE pipe (IS 14930 Part II) having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good of 63 mm outer dia and 50 mm Inner diaetc. as per specification

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, multi strand wire in the existing surface/ concealed, FRLS PVC conduit / PVC casing caping as per specification and IS: 694 (2010) 3 x 1.5 sq. mm as per direction of officer in charge

Supplying and laying following sizes 4 x 16 sq. mm. one number FRLS PVC insulated/XLPE, PVC sheathed, steel armoured, aluminum conductor power cable of 1.1 KV grade direct in ground at a depth not less than 40 cm and upto 90 cm including excavation, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1).

Supplying and making end termination with brass compression gland and aluminum lugs for following size 4 X 16 sq. mm (28 mm) armoured aluminum conductor power cable of 1.1 KV grade as per specification.

Supplying and fixing water tight terminal box made of 1.6mm thick M.S. sheet with detachable gland plate in bottom, hinged front open able cover, rubber gasket, having 1 Nos 4way connector and 1 No SPMCB inside the box for cable connection, fixed to pole with 2 Nos clamp made from 40x3mm M.S. flat with 2 No nut bolt dully painted with 2 coat of red oxide paint and 2 coat aluminum paint complete as per specification

Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification

Providing maintenance free earthing with following size GI pipe including making bore pit of minimum 150mm dia, providing and laying approved make Earthing Electrode of Pipe-in-Pipe technology as per IS 3043(R 2016) -1987 made of corrosion free G.I. Pipes having outer pipe of 80mm dia and inner pipe of 50mm dia and filling with specified qty highly conductive compound around pipe and above that with soft soil in bore pit complete and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. as per specification

Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as per specification

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS powder coated sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as per specification

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminum bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc. complete as per specification

Providing and fixing metal clad, TP&N switch fuse unit (re-wirable), 415/500 volts, with porcelain re-wireble fuses including drilling holes on the board, connections, earthing the body etc. as per specification

Providing and fixing metal clad, TP&N motorized change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as per specification

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as per specification

Providing and fixing panel mounting digital type VAF (Volt-amp-frequency combined) Multi-Function meter of size 100x100 (NS) in existing cubical panel including connection, testing and commissioning etc. as per specification

Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as per specification

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu

Supplying and fixing DP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification

Supply of 15 KVA THREEphase Silent DG Set comprising of EICHER/TMTLmake engine model 220A0- EG015, coupled to CG/KEC/LS/MCAL make 15KVA/12KW, 415 Volt alternator mounted on a common base frame along with other accessories. AMFControl Panel, Fuel tank, Battery with leads.

RAM KISHOR JHA (BID ID -3280456)

SHASANK SEKHAR NAYAK (BID ID -3280404)