Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹3.3 Cr
EMD Value
₹6.6 L
Closing Date
29 Oct 2024, 5:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Facilities Management Division, Bangalore
HINDUSTAN AERONAUTICS LIMITED Facilities Management Division, Bangalore
Renovation of Ground Floor and Part of Third Floor at Corporate Office, Bangalore.
9874
TENDER NOTICE/NCP/30/24-25/02
Works
Contract Section Civil-FMD-Bangalore
₹0
₹6.6 L
29 Oct 2024
3 Oct 2024
3 Oct 2024
29 Oct 2024
HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION
NAME OF THE WORK: Renovation of Ground Floor and Part of Third Floor at Corporate Office, Bangalore. CONTRACT NO. HAL/FMD/C-64/24-25
Name of the Contractor :
Sl. No. Specification Quantity Unit Rate in Figs [Excluding GST] Rate in Words Amount
Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The Tenderer shall abide by prevailing GST act. (2) L1 (lowest quote) will be determined based on the total quoted amount including GST. (3) This BOQ specification has to be read in conjunction with detailed technical specification and tender drawings if any.
Part 'I' - Civil Works
1 Disposal of moorum / building rubbish / malba / similar unserviceable, dismantled materail or waste material of partitions, ceiling boards, tiles, frames, etc., by mechanical transport including loading, transporting, unloading in all lifts / loads upt 10km distance from HAL and disposal of the same as per the regulations, etc., all complete as per directions of Engineer-in-Charge. 15.00 Cu m 0.00
2 Providing and laying cement concrete in parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal sizederived from natural sources), etc., all complete as per direction of Engineer-in-charge. 12.00 Cu m 0.00
3 Supply and casting Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level with finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources), etc., all complete as per direction of Engineer-in-charge. 2.00 Cu m 0.00
4 Formwork for Lintel Beams, window sills, etc., by providing timber, wooden planks, runners / M.S. sheets with all supports, struts, braces, wedges, scaffolds, bracings, ladders, gangways, dressing with oil including M.S. bolts nuts and washers, temporary openings, filleting for a stop, chamfered edges, internal / external splayed, rounded angles or grooves for forming throating including making temporary openings in the forms for pouring concrete etc as per drawing, etc., all complete as directed by the Engineer-in-Charge 62.00 Sq m 0.00
5 Supplying, straightening, fabricating and fixing Steel reinforcement of HYSD TMT bars of not less than Fe 500 conforming to IS 1786 for all concrete reinforcment members / works including cutting to length, bending to shape required, including cranking, bending spirally for hooping for column, hooking ends and binding with mild steel wire (Annealed) not less than 0.90mm dia or securing with clips, including fixing and bracing, wastage, welding, supporting or otherwise holding firmly in position so that the placing and ramming of concrete will not displace it, etc., all complete as per specifications, drawings and as directed by the Engineer-in-Charge. Note :1. For measurement, the weight of steel sections, plates, reinforcement steel bars, wire fabrics etc., shall be calculated from the tables given in relevant Indian standards or actual whichever is less. Where the weight is not given in Indian standards, it shall be calculated at 7850 kg/m³. No tolerance on account of rolling margin shall be allowed on the nominal weight of steel sections etc. complete as per direction of Engineer-in-Charge. 400.00 Kgs 0.00
6 Supply and laying Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level in all floors level in all shapes and sizes in 1:6 Cement mortar including curing etc as per drawing, etc., all complete as per direction of Engineer-in-Charge. 30.80 Cu m 0.00
7 Supply and laying Half brick masonry in Partition walls with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level in all floors level with 1:4 Cement mortar (1 cement :4 coarse sand) etc as per drawing, etc., all complete as per direction of Engineer-in-Charge. 30.00 Sq m 0.00
8 Providing and fixing Granite stone slab of 18mm thick, like Ruby Red / Black / Cherry with gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish, etc., all complete at all levels as per direction of Engineer-in-Charge. 11.22 Sq m 0.00
9 Providing and fixing Ceramic glazed wall tiles (Light / dark shade) conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black , in skirting, risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.30Kgs per Sq m, including pointing in white cement mixed with pigment of matching shade of any size, etc., all complete as directed by Engineer-in-Charge. 302.00 Sq m 0.00
10 Providing and fixing expansion hold fasteners on C.C. / R.C.C. / Brick masonry surface backing including drilling necessary holes and the cost of bolt of Wedge expansion type, etc., all complete as per direction of Engineer-in-Charge.
a) Fastener with threaded dia 6mm. 150.00 Nos 0.00
b) Fastener with threaded dia 10mm. 20.00 Nos 0.00
c) Fastener with threaded dia 12mm. 36.00 Nos 0.00
11 Providing and fixing 18mm thick skirting with Pre-laminated matching to wooden grains (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs, etc., and priming coat on unexposed surface, etc., all complete as per direction of Engineer-in-Charge. (HAL will finalize the pattern / colours) 21.00 Sq m 0.00
12 Providing and fixing Second Class Teak wood for frames of doors, windows, hand rails, frame work for partitions, etc., cut to shape and required curvature and preparing the surfaces to receive the polishing fixed in position with hold fast lugs / with dash fasteners of required dia & length / SS Screws at all heights, with necessary moisture content test, etc., all complete as per direction of Engineer-in-Charge. (Fastners / hold fasts / SS Screws to be paid separately) 17.00 Cu m 0.00
13 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section [90 x 45]mm having single rebate of [32 x 15]mm to receive shutter of 30mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, etc., all complete as per direction of Engineer-in-Charge. 50.00 R m 0.00
14 Providing and fixing 30mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856 of approved brand/type, etc., all complete as per direction of Engineer-in-Charge. 24.00 Sq m 0.00
15 Providing and fixing 12mm thick commercial ply conforming to IS : 1328 BWR type. plain lining with necessary screws/nuts & bolts / nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work / Plastered surfaces, etc., complete as per direction of Engineer-in-Charge (Frame work shall be paid for separately) 1250.00 Sq m 0.00
16 Providing & Fixing decorative high pressure 1.0mm thick laminated sheet of plain / wood grain in gloss / matt / suede finish to required pattern and combinations as per the drawings, etc., on plywood with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality / brand, etc., complete as per direction of Engineer-in-Charge. 1600.00 Sq m 0.00
17 Providing [40 x 5]mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block [30 x 10 x 15]cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size), etc., all complete as per direction of Engineer-in-Charge. 30.00 Nos 0.00
18 Providing and fixing 35mm thick flush door shutters conforming to IS :2202 (Part I) non-decorative type of approved brand / make, core of block board construction with frame of 1st class hard wood & lipping with 2nd class teak wood battens 25mm minimum depth on all edges and well matched commercial 3 ply veneering with vertical grains or cross bands including ISI marked Stainless Steel butt hinges with necessary screws and face veneers on both faces of shutters and making rectangular vision panel of 0.10Sq m with 6mm thick clear heat strengthened glass, etc., all complete as per direction of Engineer-in-Charge. 30.24 Sq m 0.00
19 Providing and fixing panelling with minimum 5mm thick glass panes or glazing in panelled or glazed shutters 25mm to 40mm thick for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured), etc., all complete as per direction of Engineer-in-Charge. 75.00 Sq m 0.00
20 Providing and fixing bright finished brass handles of 125mm size with screws, etc., all complete as per direction of Engineer-in-Charge. 36.00 Nos 0.00
21 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc., all complete as per direction of Engineer-in-Charge. 18.00 Nos 0.00
22 Providing and fixing bright finished brass tower bolts of [250 x 10]mm (barrel type) with necessary screws, etc., all complete as per direction of Engineer-in-Charge. 36.00 Nos 0.00
23 Providing and fixing bright finished brass 100mm mortice latch and lock with min. 4 levers and a pair of lever handles of approved quality with necessary screws, etc., all complete as per direction of Engineer-in-Charge. 30.00 Nos 0.00
24 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35Kgs and door width upto 700mm), with necessary accessories and screws, etc., all complete as per direction of Engineer-in-Charge. 30.00 Nos 0.00
25 Providing and fixing aluminium sliding door bolts(aldrop) of [250 x 16]mm , ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws, etc., all complete as per direction of Engineer-in-Charge. 12.00 Nos 0.00
26 Providing and fixing 20mm dia chromium plated brass curtain rod / Towel rail of 600mm long having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves, etc., wherever necessary, etc., all complete as per direction of Engineer-in-Charge. 12.00 Nos 0.00
27 Providing and fixing STAINLESS STEEL RAILING ( Grade 304) made of Hollow tubes, channels, plates combination of various members, etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts, etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-Charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.,) 224.00 Kgs 0.00
28 Providing and laying Glazed vitrified floor tiles Matt / Antiskid finish of Size [600 X 600]mm as indicated below for Paper Joint in different sizes (Thickness to be sepcified by the manufacturer) with water absorption less than 0.08% and confirming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement: 4 course sand), including grouting the joints with grey cement slurry @ 3.30Kgs / Sq m including grouting the joints with white cement and matching pigments, etc., all complete as per instructions of Engineer-in-Charge. 76.00 Sq m 0.00
29 Providing and laying Double charged Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average thickness of 6mm including, pointing and grouting the joints with white cement and matching pigment, etc., all complete as per direction of Engineer-in-Charge. 954.00 Sq m 0.00
30 Providing and laying Double Charged Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6mm thickness, including grouting of joints (Payment for grouting of joints to be made separately), etc., all complete as per direction of Engineer-in-Charge. 44.00 Sq m 0.00
31 Providing and laying Polished Granite stone flooring and stiar case raiser and steps in colour Black, Cherry / Ruby Red or Equivalent in required design and patterns, in linear as well as curvilinier portions of building as complete as per the architectural drawings / Site condition with 18mm thick stone slab or 20mm (average) thick base of cement mortar 1:4 ( 1 cement : 4 coarse sand) laid and jointed with cement slurry and pointed with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing, nosing, chamfering and making grooves, etc., all complete as per direction of Engineer-in-Charge. 204.00 Sq m 0.00
32 Providing and fixing FALSE CEILING with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks of approved brand) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.60mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.50mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of [25 x 10 x 0.50]mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels [45 x 15 x 0.90]mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.50mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.50mm, at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size [3.50 x 25]mm at 230mm c/c, including jointing and finishing to a 625.00 Sq m 0.00
flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, etc., all complete as per drawings, specification and direction of the Engineer-in-Charge.
33 Providing and fixing Single socketed pipes of 110mm diameter unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A of approved brand, on wall face including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, etc., all complete as per direction of Engineer-in-Charge. 60.00 R m 0.00
34 Providing and fixing Single socketed pipes of 75mm diameter unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A of approved brand, on wall face including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, etc., all complete as per direction of Engineer-in-Charge. 60.00 R m 0.00
35 Plastering to internal brick wall with 15mm thick on the rough side of single or half brick wall of cemnet mortar (1:6) including leveling, curing and making the level smooth and at all heights and execute the work, etc., all complete as per direction of Engineer-in-Charge. 200.00 Sq m 0.00
36 Providing and applying internal wall and ceiling painting with two coats of premium acrylic emulsion paint of interior grade (Colour and texture range from dark anti reflective to light rlective), having VOC (Volatile Organic Compound ) content less than 50Grams / Litre after applying white cement based putty of average thickness 1mm over the plastered wall surface including preparation of the surfces, with a coat of low VOC primer with emery paper to bring to smooth and even including applying additional coats wherever required to achieve even shade and colour of approved brand, etc., all complete as per direction of Engineer-in-Charge. 1200.00 Sq m 0.00
37 Providing and finishing old walls in two or more coats with Premium Acrylic Smooth exterior paint with Silicone additives of approved brand of required shade @ 1.43Ltr / 10Sq m over existing cement paint surface after Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches, etc., all complete as per direction of Engineer-in-Charge. 164.00 Sq m 0.00
38 Providing and applying synthetic enamel paint of approved brand and manufacture of required colour to give an even shade in One or more coats on old work by cleaning and srcapping to make the surface smooth before appling paint, etc., all complete as per direction of Engineer-in-Charge. 54.00 Sq m 0.00
39 Providing and applying synthetic enamel paint in Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture, etc., all complete as per direction of Engineer-in-Charge. 18.00 Sq m 0.00
40 Providing and applying with ready made wax polish on old wood work of approved brand and manufacture in One or more coats, etc., all complete as per direction of Engineer-in-Charge. 94.00 Sq m 0.00
41 Dismantling 15 to 40mm dia G.I. / CPVC pipe including stacking of dismantled pipes (within 50metres lead) including making temporary arrangements for continuing ongoing services to toilets, etc., all complete as per direction of Engineerin-Chare. 100.00 R m 0.00
42 Fixing chowkhat in existing opening in brick / RCC wall with dash, fasteners / Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners / chemical fastener, etc., all complete as per direction of Engineer-in-Charge. 18.00 Nos 0.00
43 Providing and fixing bright finished brass hard drawn hooks (coat hooks) and eyes of 300mm size, etc., all complete as per direction of Engineer-in-Charge. 12.00 Nos 0.00
44 Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba, making temporaray arrangements for blocking service lines to avoid water leakages, etc., all complete as per directions of Engineer-in-Charge. 12.00 Nos 0.00
45 Repair to plaster of thickness 12mm to 20mm in patches of area lesser than 2.50Sq m including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, without causing hindrance / protecting the existing floor finish work, etc., all complete as per the direction of Engineer-in-Charge. 40.00 Sq m 0.00
46 Demolishing cement concrete manually / by mechanical means including disposal of material within 50metres lead as per direction of Engineer- in-Charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) and including stacking material and disposal of dismantled materials up to a lead of 10kilometre outside HAL, after making temporary proetction for existing service lines, etc., all complete as per direction of Engineer-in-Charge. 10.00 Cu m 0.00
47 Demolishing cement concrete manually / by mechanical means including disposal of material within 50metres lead as per direction of Engineer-in-Charge. Nominal concrete 1:4:8 or richer mix (i/c equivalent design mix) and including stacking material and disposal of dismantled materials up to a lead of 10kilometre outside HAL, after making temporary proetction for existing service lines, etc., all complete as per direction of Engineer-in-Charge. 6.00 Cu m 0.00
48 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts, etc., complete and stacking within 50metres lead of area 3Sq metres and below, including stacking material and handing over the useful materials to HAL maintenance department and disconnecting the service lines if any, etc., all complete as instructed by Engineer-in-Charge. 35.00 Nos 0.00
49 Dismantling wooden boardings in lining / partitions of walls / work stations excluding supporting members after disconnecting the electrical / AC service lines if any but including stacking within 50metres lead and including stacking material and disposal of dismantled materials up to a lead of 10kilometre outside HAL, etc., all complete as per direction of Engineer-in-Charge. 388.00 Sq m 0.00
50 Dismantling cement asbestos or other hard board ceiling or partition walls of minimum 75mm thick including stacking of serviceable materials after disconnecting the electrical / AC service lines if any and disposal of unserviceable materials within 50metres lead and disposal of dismantled materials up to a lead of 10kilometre outside HAL, etc., all complete as per direction of Engineer-in-Charge. 754.00 Sq m 0.00
51 Dismantling of road gully chamber / trap of various sizes including C.I. grating with frame and making temporary arrangements to protect ongoing service lines,including stacking of useful materials near the site and disposal of unserviceable materials within 50metres lead including refilling the excavated gap, etc., all complete as per direction of Engineer-in-Charge. 25.00 Nos 0.00
52 Dismantling aluminium / Gypsum partitions, doors, windows / ventilators, fixed glazing and false ceiling after disconnecting the electrical service and AC lines if any including disposal of unserviceable material and stacking of serviceable material with in 50meters lead, etc., all complete as directed by Engineer-in-Charge. 116.00 Sq m 0.00
53 Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 10kilometre outside HAL, stacking serviceable and unserviceable material separately including cutting reinforcement bars,after making temporary proetction for existing service lines, etc., all complete as per direction of Engineer-in-Charge. 4.00 Cu m 0.00
54 Demolishing brick work with cement mortar manually / by mechanical means, after disconnecting the electrical service and AC lines if any, including stacking of serviceable material and disposal of dismantled materials up to a lead of 10kilometre outside HAL, etc., all complete as per direction of Engineer-in-Charge. 24.00 Cu m 0.00
55 Dismantling / removing tile work (for thickness of tiles 10mm to 25mm) of in floors and in walls laid in cement mortar after disconnecting the electrical service and AC lines if any, including stacking material and disposal of dismantled materials up to a lead of 10kilometre outside HAL, etc., all complete as per direction of Engineer-in-Charge. 400.00 Sq m 0.00
56 Dismantling of flushing cistern of all types (C.I. / PVC / Vitrious China) including stacking of useful materials near the site, making temporary arrangements to avoid water leakage and disposal of unserviceable materials within 50metres lead, etc., all complete as per direction of Engineer-in-Charge. 18.00 Nos 0.00
57 Providing and fixing Glass shelf of size [600 x 120 x 5]mm with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs, etc., all complete as per direction of Engineer-in-Charge. 8.00 Nos 0.00
58 Providing and fixing C.P. brass toilet paper holder of approved brand and fixing with screws, raw plugs, etc., all complete as per direction of Engineer-in-Charge. 12.00 Nos 0.00
59 Providing and fixing beveled edge mirror of size [600 x 450]mm of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers, etc., all complete as per direction of Engineer-in-Charge. 10.00 Nos 0.00
60 Providing and fixing Wall hung half pedestal Vitreous China Wash basin size of approx size [630 x 450]mm fixed with with C.I. brackets / rack bolts, single 15mm C.P. brass pillar taps, 32mm C.P. brass waste coupling of standard pattern,P.V.C. waste pipe with waste fittings of 40mm dia and make it function of approved brand/make, including painting of fittings and brackets, cutting and making good the walls wherever required, etc., all complete as per direction of Engineer-in-Charge. 10.00 Nos 0.00
61 Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink of size [510 x 1040]mm bowl depth 250mm with drain board as per IS:13983 with C.I. brackets and stainless steel plug 40mm, P.V.C. waste pipe with waste fittings of 40mm dia, including painting of fittings and brackets, cutting and making good the walls with counetr matching sealant if required, etc., all complete as per direction of Engineer-in-Charge. 3.00 Nos 0.00
62 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) of approved brand with ISI marked white solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all connecting fittings and fixtures to make it operational completely, including cutting and making good to the walls and floors wherever required, etc., all complete as per direction of Engineer-in-Charge. 4.00 Nos 0.00
63 Providing and fixing 8mm dia C.P. / S.S. Jet (Health Fuacet) with flexible tube minimum 1.0metre long with S.S. triangular plate on walls / Eureopean type W.C. material of approved make and quality, etc., all complete as per instructions of Engineer-in-Charge. 12.00 Nos 0.00
64 Providing and fixing white colour wall hung vitreous china battery based infrared sensor operated urinal of approx. size [610 x 390 x 370]mm having pre & post flushing with water (250 ml & 500 ml consumption approx.), having water inlet from back side, including fixing to wall with brackets embedded in cement mortar (1:3), connecting the waste pipe / waste coupling to floor trap with all necessary fittings and accessories like 32mm dia semi-rigid PVC waste pipe (concealed in the wall) including PVC waste fittings, clamps etc making it operational, etc., all complete as per manufacturers specification and direction of Engineer-in-Charge. 7.00 Nos 0.00
65 Providing, fixing, testing and commissioning trap (floor trap) of approved make with 100mm inlet and 75mm outlet of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors, connection with PVC soil / waste pipe, necessary 150mm thick cement concrete (1:2:4) for embedding the trap, etc., all complete as directed by the Engineer-in-Charge. 12.00 Nos 0.00
66 Constructing masonry Chamber [60 x 60 x 75]cm inside or outside (or approx. size as per site condition), in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : 18.33.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5, etc., all complete as per direction of Engineer-in-Charge. 2.00 Nos 0.00
67 Providing and fixing 15mm nominal bore dia C.P. brass bib cock of approved quality conforming to IS:8931, etc., all complete as directed by the Engineer-in-Charge. 12.00 Nos 0.00
68 Providing and fixing 15mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms, etc., all complete as per direction of Engineer-in-Charge. 4.00 Nos 0.00
69 Providing and fixing Concealed Chlorinated Polyvinyl Chloride (CPVC) pipes of approved brand, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, fixing the pipe with clamps at 1.00m spacing, necessary reducers, tank adaptors, etc., This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints and making good the walls, etc., all complete as per direction of Engineer-in-Charge.
a) 15mm dia 30.00 R m 0.00
b) 20mm dia 40.00 R m 0.00
c) 25mm dia 20.00 R m 0.00
d) 32mm dia 30.00 R m 0.00
e) 40mm dia 40.00 R m 0.00
70 Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50m lead and disposal of unserviceable materials into municipal dumps and making temporary arrangements to protect / countinue ongoing service lines of other floors, etc., all complete as per direction of Engineer-in-Charge.
a) 100mm diameter 40.00 R m 0.00
b) 150mm diameter 50.00 R m 0.00
71 Supply and Making connection of drain pipes of 100 to 250mm diamete or sewer line with existing manhole including breaking / cutting into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with C.M 1:3 ( 1 cement : 3 caorse sand ), finished with a floating coat of neat cement and making necessary channels for the drain, etc., all complete as directed by the Engineer-in-Charge. 4.00 Nos 0.00
72 Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, filling up the gaps at junctions, with dash fasteners and EPDM rubber / neoprene gasket, etc., all complete as per architectural drawings and the directions of Engineer-in-Charge. (Glazing, paneling and dash fasteners to be paid for separately) : 54.48 Kgs 0.00
73 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions, etc., With float glass panes of minimum 5mm thickness (weight not less than 12.50 Kgs / Sq m) along with EPDM rubber / neoprene gasket, required clips, etc., all complete as per the architectural drawings and the directions of Engineer-in-Charge. 5.40 Sq m 0.00
74 Providing and fixing mineral fibre false ceiling tiles (of approved brand/make) with 16mm thick beveled tegular edge with (NRC 0.55 to 0.60) at all heights of size [595 X 595]mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%,Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7) in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33mm thick (galvanized @120 gsm) comprising of main T runners of [15 x 32]mm of length 3000mm, cross T of size [15 x 32]mm of length 1200mm and secondary intermediate cross T of size [15 x 32]mm of length 600mm to form grid module of size [600 x 600]mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50mm long 8mm outer diameter M-6 dash fasteners, 6mm diameter fully threaded hanger rod up to 1000mm length and L-shape level adjuster of size [85 x 25 x 2]mm, spaced at 1200mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size [24 x 24 X 3000]mm made of 0.40mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450mm centre to centre & 40mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-Charge. 276.00 Sq m 0.00
75 Providing and fixing horizontal level Knauf Cellio Open cell GI lay-in ceiling CELL with border panels forming board edge of size [600 x 600 x 38]mm (Nominal) having cell size of [100 x 100]mm made of 120 gsm galvanized steel as per IS 277 (2003) suitable for architectural finishes in 0.35mm thickness as per in IS:513 (1994) in Global white color. The tile shall be electrostatically polyester powder coated using RoHS compliant powder having coating thickness ranging from 60-80 microns. The powder coating shall pass Salt Spray Test for 750 hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5% at 60˚ as per ASTM D523. Tile shall have a Fire Performance class A1 as per EN-13964 SUSPENSION: The tile shall be laid on Knauf Suprafine 38 with 15mm wide T - section flanges colour global white (matching to tile colour) having double stroke rotary stitching on all T sections i.e., the Main Runner, 1200mm & 600mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.50 Kgs/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15 Kgs/m. The end details of the cross tee shall be made of pre hardened steel clip fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull-out strength of more than 100Kgs. The T Sections shall be made of hot dipped galvanized steel 90gsm and pre-painted steel with baked polyester paint of 0T bending capability. 240.00 Sq m 0.00
INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using Knauf suspension system (specifications below) at 1200mm maximum. The First / Last Knauf suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form [1200 x 600]mm module. Cut cross tees longer than 600mm require independent support [600 x 600]mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees. Perimeter trim to be Knauf wall angles of size [3000 x 19 x 19]mm, secured to walls using screws at 450mm centre to centre maximum. All border cut tiles shall be laid, using Knauf lay-in end cap for installation to have a Microlook effect on perimeters. Installation shall be carried out as per Knauf recommended procedure. Note: MTC of material sto be submitted by agency to HAL.
76 Providing & fixing horizontal level suspended ceiling comprising of Knauf Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063 T5. The baffle blade shall be in size of [100 x 25 x 3600]mm in powder coated to Woodgrain / Plain finish (Red Oak, Cherry, Black / White). The baffle shall be electrostatically polyester powder coated to a coating thickness of 60-80 micron. The powder coating shall pass Salt Spray Test for 750 Hours as per ASTM B117, QUV –A Test for 1000 hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000 hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation within a manufacturing batch shall be delta E<1 using Excite / BYK Gardner instrument and gloss level 25±5% at 60˚ as per ASTM D523 (Not applicable of Wood Grain Shade). The baffle blade shall be suspended using Slotted U-profile of [20 x 30 x 3700]mm (Thk-1.5mm) having slots in module of 25mm to keep baffles at an on-center spacing in multiples of 25mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. SUSPENSION: Shall be hanged using baffle hanger from U-profile made of mild steel with powder coating thickness of 60-80 micron. The U – profile to comprise of alternate square & rectangular slots of [6.5 x 6.5]mm & [28 x 6.5]mm respectively on the web for locking the baffle hanger using plugin clip to secure the hanger in perfect position and achieve uniform spacing between baffles. The overall dimension of the U – profile is 20(W) x 30 (H) x 3750 (L) mm and is rolled form from 1.50mm thick mild steel with a powder coating thickness of 60-80micron. U- Profile to be connected to each other using U –Profile Splice. 150.00 Sq m 0.00
The U- profile shall be hanged from the true ceiling using threaded rod using a U- Profile hanger. Installation of U-Grid. Note:MTC of the materails to be submitted by agency to HAL. The U profile to be suspended at every 1200mm center to center using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.7M. 1st U-Grid Channel must be no more than 400mm from the perimeter. Installation of Knauf Baffles: Locate the slot for Baffle Hangers in U Profile section at 1200mm centers. Hangers are inserted into the slot, then rotated 90° and fixed into position by tightening the grub screw. Baffle to be lifted into position and hangers engage over lip of U-Grid Channel. Each Hanger to be secured into position by inserting the Locking Clip. When doing continuous installation, Baffles blades are to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into open Baffle slots. Note: MTC of materials to be submitted by agency to HAL.
77 Supply and Installation of Kanuf ceiling solution ULTIMA CREATE [600 x 600 x 19]mm Microlook Edge Tile with Silhouette 38 Grid system & standard wall angle (Including grid system). The work should be excuted at all heights including necessary scaffoldings all suitable for architectural finishes as instrcuted by Engineer-in-Charge. (Shop drawing to be submiited by agency and obtain approval from HAL before finalizing tiles/pattern/design) Note: MTC of material to be submitted by agency. 200.00 Sq m 0.00
78 Supplying and Fixing of Curviliniear urinal Partitions Plates / wall made out of 8mm thick glass with frosting and fixed to the walls with SS Fittings of size 900 H nd 450mm W at requuisite levels as per the manufacturers instruction including necessary screws, fittings and fixures, etc., all complete as directed by Engineer-in-Charge. 8.00 Nos 0.00
79 Supplying and fixing wooden flooring made up of 12mm thick solid core wooden lanminated plankings tounged and grooved flooring with unilin /tounge-grrove locking arrangement) having min 0.20mm thick abrasive layer. The wooden flooring shall be laid over 2mm thick under layer of polythurethane foam laid over 250micron polythene sheet of 250micron over a hard subfloor including requisite accessories like end profile, transition profile, reducer T profile, etc., The rate quoted shall be including all incedental itms required for completion of the work. The work shall be carried out as per Manufacturers instructions and execution as per instructions of Engineer-in-Charge. 90.00 Sq m 0.00
80 Supplying, laying, testing and commissioning the following dia PVC pipes of 6 kg/cm² SWR grade and of approved make with rubber ring joints conforming to IS 5382, jointed together with solvent, in trenches, floors and walls, including all necessary fittings & specials, bends, branches, sockets, pipe cutting and wastages, cutting and making good the floors etc., all complete as directed by the Engineer-in-Charge.
a) 75mm dia 30.00 R m 0.00
81 Providing and fixing C.P. brass toilet paper holder of standard size and brand on wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88gms, etc., all complete as per direction of Engineer-in-Charge. 12.00 Nos 0.00
82 Providing and fixing S.S. liquid soap holder with dispenser of available size / shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105gms, etc., all complete as per direction of Engineer-in-Charge. 10.00 Nos 0.00
83 Providing and fixing CP brass Angle cock with all necessary with washers, leak proof rubber gasket arrangement, etc., and packing with white cement, etc., all complete as directed by Engineer-in-Charge. 20.00 Nos 0.00
84 Providing and fixing Wall mounted white vitreous china water closet with ISI marked, auto close white solid plastic seat and lid with concelaed S.S. flush valve fixed over steel plate with all connecting fittings and fixtures to make it operational completely, including cutting and making good the walls and floors wherever required, etc., all complete as per direction of Engineer-in-Charge. 10.00 Nos 0.00
85 Supplying and fixing Roller Blind consisting of control unit idler, head of rail, roller tube, bottom rail operating chain, brackets and clamp / nuts / bolts /of approved colour / pattern including necessary supporting hangar holder / screws and all complete as directed by EIC of approved design, shade and pattern, made up of lined single layer of fabric, hemmed at the bottom and sides and top with eyelid ring studs including curtain rod, holder, etc., all complete as directed by the Engineer-in-Charge. 202.00 Sq m 0.00
86 Providing and fixing bright finished brass handles of 200mm size on doors with necessary screws, etc., all complete as per instructions of Engineer-in-Charge. 36.00 Nos 0.00
87 Supply and fixing wall Paneling with 12mm thick ply on pine wood frame of size [50 x 50]mm placed at 600mm c/c filling the frame with 50-75mm thick material (wool / bed) in panes and covering the pane area with spreading designer leatherite cover over it using steel button screws or pin headed buttons to the required shape / pattern as per drawing & as instructed by Engineer In-charge. Note: 1. Cost of fabric/leatheraite should not be less than Rs 3000 / Sq m. 2. The leatherite will be selected by architect. 141.00 Sq m 0.00
88 Supplying and fixing etching sticker min. 70 micron thick and of approved design fixed with adhesive over glass, etc., all complete as directed by the Engineer-in-Charge. 50.00 Sq m 0.00
Sub-Total of Part 'I' - Civil Works (Excluding GST) 0.00
PART II A - ELECTRICAL, VOICE & DATA WORKS
LED Light fixtures
1 Supply, fixing in flush with the false ceiling including suitable fixing arrangment using Chain links, testing & commissioning of recess mounting type square(2'X2') LED lighting fixture of wattage not exceeding 36watt made out of white powder coated CRCA housing/ aluminium housing, front frame with translucent /polycarbonate cover including control gear. The luminaire should have Lumen efficacy ≥100 lm/watt and lumen output not less than 3600lumens with PF >0.9 and Colour temperature shall be ≥5700K operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections and other standard accessories complete in all respects and as directed by Engineer incharge. LED used in the lighting fixtures should be one of the approved make. LM79 certification for luminaires & LM80 certificate for LED shall be produced.The LED Light fixture shall be of Crompton model no:LCTLRNE-36W-FO-CDL/Equivalent model in other approved makes luminaries which meets the above technical specification. LED used in the luminaire should be one of approved make as per approved make list of HAL. 75.00 Nos 0.00
2 Supply, fixing in flush with the false ceiling including suitable fixing arrangment using Chain links, testing & commissioning of recess mounting type Merged octagon design-Geometrically aligned LED lighting fixture of wattage not exceeding 36watt made out of white powder coated CRCA housing/ aluminium housing, front frame with translucent /polycarbonate cover including control gear. The luminaire should have Lumen efficacy ≥100 lm/watt and lumen output not less than 3600lumens with PF >0.9 and Colour temperature shall be ≥5700K operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections and other standard accessories complete in all respects and as directed by Engineer incharge. LED used in the lighting fixtures should be one of the approved make. LM79 certification for luminaires & LM80 certificate for LED shall be produced.The LED Light fixture shall be of Crompton model no:LCTLRF2-36W-TL/Equivalent model in other approved makes luminaries which meets the above technical specification. LED used in the luminaire should be one of approved make as per approved make list of HAL. 17.00 Nos 0.00
3 Supply and fixing on ceiling/in flush with the false ceiling as per site requirement testing & commissioning of round type Surface/recess mounted LED downlighter with PDC aluminium housing and high translucent frosted plastic diffucer makes it a robust luminaire, wattage not less than 18W LED lighting fixture, lumens efficiency ≥ 100lm/w at luminaire level, effficent heat sink, Colour temprature shall be ≥5700K, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V. 79 certification for luminare & LM80 certificate for LED shall be produced. including control gear, power factor of control gear shall be >0.90. Crompton model no:LCDSPLN-S-18-CDL/LCDSPLN-R-18-CDL/Equivalent model in other approved makes luminaries which meets the above technical specification. LED used in the luminaire should be one of approved make as per approved make list of HAL. 95.00 Nos 0.00
4 Supply and fixing on existing wall / ceiling, testing & commissioning of surface mounting, Batten LED light fittings (four feet) of wattage not exceeding 40W made out of aluminium extruded Housing integrated LED batten, equipped with 4kv in-built surge protection, IP20 Protection rating including control gear. The luminaire should have Lumen efficacy ≥110/120 lm/watt and lumen output not less than 4400/4800lumens with PF >0.9 and Colour temperature shall be ≥5700K, operating on single phase 240V voltage 50 Hz AC supply with voltage range 150-275V including necessary interconnections and other standard accessories complete in all respects and as directed by Engineer incharge, offered model shall of Crompton model no:CIS-305-40-57-SL-DP-NWH/equivalent model of other approved makes. LED used in the lighting fixtures should be one of the approved make. LM79 certification for luminaires & LM80 certificate for LED shall be produced. 2.00 Nos 0.00
5 Supply and fixing in flush with the false ceiling as per site requirement testing & commissioning of round type recess mounted LED downlighter in gypsum/Wooden false ceiling with aluminium die-cast body, finish with drop down diffuser with optimized heat sink for efficiant heat dissipation, wattage not less than 3W LED lighting fixture, lumens efficiency ≥ 100lm/w at luminaire level, effficent heat sink, Colour temprature shall be =>6500K, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V. LM 79 certification for luminare & LM80 certificate for LED shall be produced. including control gear, power factor of control gear shall be >0.90. Bajaj make model no:Havells LHEBHDP7IZ1W003 /Equivalent model in other approved makes luminaries which meets the above technical specification. LED used in the luminaire should be one of approved make as per approved make list of HAL. 200.00 Nos 0.00
6 Supply, fixing directly to the designer baffle ceiling/wall/column using suitable mounting arrangements testing & commissioning of Pureline Slim suspended/ surface minimum 18W LED light 50/52mm aluminium extruded linear lighting, 1200 mm long including suitable LED driver, the driver shall have PF >0.9 and Colour temperature shall be =>5700K, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections between driver and lighting fixtures complete in all respect and as directed by EIC. The lighting fixture shall be Crompton model no:CCP-121-18-57-SL-NWH or Equivalent make in other approved makes. 61.00 Nos 0.00
7 Supply and fixing on ceiling testing & commissioning of round type Surface mounted LED downlighter with Slim surface mounted, wattage not less than 24W LED lighting fixture, lumens efficiency ≥ 100lm/w at luminaire level, effficent heat sink, Colour temprature shall be ≥6500K, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V. 79 certification for luminare & LM80 certificate for LED shall be produced. including control gear, power factor of control gear shall be >0.90. Havells LHEAAHP7IL1W024/Equivalent model in other approved makes luminaries which meets the above technical specification. LED used in the luminaire should be one of approved make as per approved make list of HAL. 6.00 Nos 0.00
8 Supply and fixing on ceiling testing & commissioning of 20W LED Track light fitting made of aluminium material, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V, including necessary Track light Stanchion & interconnections between driver and lighting fixtures complete in all respect and as directed by EIC. The lighting fixture shall be Philps make Model no-31446 Track light Stanchion Track White 20W Head/Equivalent make in other approved makes.. 6.00 Nos 0.00
9 Supply, fixing directly to the ceiling/wall using suitable mounting arrangements testing & commissioning of surface mounting Decorative type 10W LED mirror light fitting, including driver, the driver shall have PF >0.9 and Colour temprature shall be ≥5700K, THD <20% operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections between driver and lighting fixtures complete in all respect and as directed by EIC. The lighting fixture shall be Bajaj make Model-BCLSB 10W WH/Equivalent make in other approved makes. 5.00 Nos 0.00
10 Supply, fixing directly to the ceiling/wall/Floor using suitable mounting arrangements testing & commissioning of 28W, 2400 Lumens for 5 meter with suitable 1no driver for each 5mtrs length of LED strip having reliable performance and anti-dust LED strips with professional design for Decorative lighting applications(Cove lighting) and Colour temperature shall be =>3000K, operating on single phase 230V voltage 50 Hz AC supply with voltage range 140-270V including necessary interconnections between driver and lighting fixtures complete in all respect and as directed by EIC. The lighting fixture shall be model no: Philips Linea Bright Cove light or Equivalent make in other approved makes. 300.00 Mtrs 0.00
11 Supply and fixing on ceiling using suitable mounting hardwares like chain link etc., testing & commissioning of LED based Decorative Coco Flower Pendant Lamp of approximate size 25.5Cm x 25.5Cm including supply of E27 type Holder & Plug and 1no 9W LED bulb with necessary inter-connections complete in all respects and as directed by Engineer-in-chage. Note: Being an Antique light fixtures Contractor has to obtain the approval from OIC/EIC by showing the model/catalogue of light ficture before perchasing. Fitting shall procured as per the approval of OIC/EIC during execution of work. 4.00 Nos 0.00
12 Supply and fixing on ceiling using suitable mounting hardwares like chain link etc., testing & commissioning of LED based Decorative Brass Detail Flower Pendent Lighting made of Brass, Glass with Antique finish and colour of clear glass of approximate size 55 x 55 x 15Cm including supply of E27 type Holder & Plug and 1no 9W LED bulb with necessary inter-connections complete in all respects and as directed by Engineer-in-chage. Note: Being an Antique light fixtures Contractor has to obtain the approval from OIC/EIC by showing the model/catalogue of light ficture before perchasing. Fitting shall procured as per the approval of OIC/EIC during execution of work. 4.00 Nos 0.00
13 Supply and fixing on ceiling using suitable mounting hardwares like chain link etc., testing & commissioning of LED based Decorative Mogul Pendent Light(Patina) made of Brass, wood with Brass, wood finish of approximate size 30.4 x 30.4 x 122Cm including supply of E27 type Holder & Plug and 1no 9W LED bulb with necessary inter-connections complete in all respects and as directed by Engineer-in-chage. Note: Being an Antique light fixtures Contractor has to obtain the approval from OIC/EIC by showing the model/catalogue of light ficture before perchasing. Fitting shall procured as per the approval of OIC/EIC during execution of work. 4.00 Nos 0.00
14 Supply and fixing on ceiling using suitable mounting hardwares like chain link etc., testing & commissioning of LED based Decorative Vntage Patina Pendent Light Lamp made of Steel with Patina finish and colour of Gold, patina of approximate size 34.5 x 34.5 x 25Cm including supply of E27 type Holder & Plug and 1no 9W LED bulb with necessary inter-connections complete in all respects and as directed by Engineer-in-chage. Note: Being an Antique light fixtures Contractor has to obtain the approval from OIC/EIC by showing the model/catalogue of light ficture before perchasing. Fitting shall procured as per the approval of OIC/EIC during execution of work. 4.00 Nos 0.00
15 Supply and fixing on ceiling using suitable mounting hardwares like chain link etc., testing & commissioning of LED based Decorative Autumn Petals Walnut Pendent Lamp made of Birch with Matt finish and colour of walnut of approximate size 38 x 38 x 43Cm including supply of E27 type Holder & Plug and 1no 9W LED bulb with necessary inter-connections complete in all respects and as directed by Engineer-in-chage. Note: Being an Antique light fixtures Contractor has to obtain the approval from OIC/EIC by showing the model/catalogue of light ficture before perchasing. Fitting shall procured as per the approval of OIC/EIC during execution of work. 4.00 Nos 0.00
16 Supply & fixing on wall using suitable mounting arragements, fixing hardwares, testing and commissioning of 400mm dia, wall mounting, oscillating type fan along with speed regulator, power cord with 6A, 3 pin plug top and other connected accessories etc., including necessary interconnections complete in all respects and as directed by the Engineer-in-charge. 50.00 Nos 0.00
17 Supply, installation, testing & commissioning of 300mm dia 900 rpm heavy duty exhaust fan of any approved make with louvers, connecting cord with 6A, 3 pin plug top and with all necessary accessories, including making wall openings and replastering to smooth finish with matching paint etc., complete in all respects and as directed by Engineer-in-charge. 5.00 Nos 0.00
18 Supply, fixing, testing & commissioning of the following factory built powder coated Double door MCB/MCCB DB of any approved make fabricated out of M.S. sheet steel enclosure & necessary cutouts for operating the MCB knobs & comprising of 200 amps tinned copper busbars & earthing bus with tapped holes including internal wiring with stranded copper PVC wires or suitable size copper strips etc. & fixing the DB in flush with wall/ on wall as per site requirement with necessary M.S. angle supports, chipping the wall and replastering to smooth finish etc., wherever required as per site condition, complete in all respects, as directed by Engineer-in-charge and comprising the following as detailed below:
a) 6 way (4 + 18), Double door Horizontal MCB DB 8.00 Nos 0.00
b) 6 way (4+18) Double door VTPN MCCB DB 1.00 No 0.00
c) 63 amps. ratings, 4P MCB, "C" curve, 10 KA breaking capacity. 6.00 Nos 0.00
d) 32 amps. ratings, TPN MCB, "C" curve, 10 KA breaking capacity. 3.00 Nos 0.00
e) 32 amps. ratings, TP MCB, "C" curve, 10 KA breaking capacity. 3.00 Nos 0.00
f) 6-32 amps. ratings , SP MCB, "C" curve, 10 KA breaking capacity. 147.00 Nos 0.00
Lighting Point wiring
19 Wiring for light point / fan point / exhaust fan point/call bell point from nearest switch box with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, fan regulator, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (as per detailed CPWD specifications for Group C wiring)
a) Wiring to single light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects. 185.00 Pts 0.00
b) Wiring to two light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects. 25.00 Pts 0.00
c) Wiring to three light point controlled by 1 No 6A, 250V gr. flush modular type SP switch complete in all respects. 55.00 Pts 0.00
d) Wiring to four light point controlled by 1 No 6A, 250V gr. flush modular type SP switch complete in all respects. 20.00 Pts 0.00
e) Wiring to exhaust/wall mounting fan point using 6A, 250V gr. flush type modular SP switch housed along with other lighting switches/separate switch box if required and 3pin 6A, 250V gr. modular type socket housed near the exhaust fan complete in all respects. 55.00 Pts 0.00
f) Wiring to Staircase light point controlled by 1 No 2 way 6A, 250V gr. flush type modular SP switch. 8.00 Pts 0.00
20 Supplying and drawing of 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed medium class PVC conduit as required 400.00 Mtrs 0.00
Wiring-Lighting circuits/submain ckts
21a Wiring for circuit/submain wiring along with earth wire with the 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 1200.00 Mtrs 0.00
Wiring for Power Points(6A & 16A power sockets)
21b Wiring for power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 3000.00 Mtrs 0.00
22 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
a) 6A one-way flush type modular SP switch. 270.00 Nos 0.00
b) 16A one-way flush type modular SP switch. 40.00 Nos 0.00
c) 6A, 3 pin flush type socket outlet. 410.00 Nos 0.00
d) 16A, 6 pin flush type socket outlet. 40.00 Nos 0.00
23 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.
a) 1 or 2 Module 70.00 Nos 0.00
b) 3 Module 140.00 Nos 0.00
c) 6 Module 80.00 Nos 0.00
d) 8 Module 70.00 Nos 0.00
24 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding plate as required 70.00 Nos 0.00
25 Supplying and fixing of follwing size Modular GI box/PVC box as per site requirement in flush with wall/on wall/on partition including cutting the wall and making good finish with same.
a) 1 or 2 Module 40.00 Nos 0.00
b) 3 Module 100.00 Nos 0.00
c) 6 Module 40.00 Nos 0.00
d) 8 Module 40.00 Nos 0.00
26 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
a) 20MM PVC Conduit 2000.00 Mtrs 0.00
b) 25MM PVC Conduit 1500.00 Mtrs 0.00
c) 32MM PVC Conduit 500.00 Mtrs 0.00
d) 40MM PVC Conduit 400.00 Mtrs 0.00
e) 50MM PVC Conduit 400.00 Mtrs 0.00
27 Supply & laying in the already excavated cable trench/cable tray/fixing on wall/duct wall with necessary M.S clamps / encasing in pipes etc., testing & commissioning of following size XLPE insulated Aluminium (Al) /Copper (cu) conductor 1.1 KV grade confirming to IS: 7098 ( part-I)/1998 with upto date amendment earthed Armoured (Arm)/un Armoured (un Arm) U.G cables and as per technical specification including stacking at site, proper storage complete etc. as required. (Note:- Excavation, sand & Brick Protection, concrete cutting, reconcreting, casing pipes will be measured separately.)
a) 4 CX 16 Sqmm Copper Un armoured conductor 150.00 Mtrs 0.00
b) 4 CX 10 Sqmm Copper Un armoured conductor 80.00 Mtrs 0.00
c) 3.5 CX 70 Sqmm Aluminium armoured conductor 5.00 Mtrs 0.00
d) 3.5 CX 70 Sqmm Copper Un armoured conductor. 20.00 Mtrs 0.00
e) 3.5 CX 50 Sqmm Aluminium armoured conductor. 5.00 Mtrs 0.00
f) 3.5 CX 35 Sqmm Aluminium armoured conductor. 5.00 Mtrs 0.00
g) 3.5 CX 25 Sqmm Aluminium armoured conductor. 5.00 Mtrs 0.00
h) 4 CX 16 Sqmm Aluminium armoured conductor. 5.00 Mtrs 0.00
i) 4 CX 10 Sqmm Aluminium armoured conductor. 5.00 Mtrs 0.00
j) 4 CX 6 Sqmm Aluminium armoured conductor. 5.00 Mtrs 0.00
k) 3CX 4 Sqmm Copper armoured conductor. 200.00 Mtrs 0.00
28 Supply and connecting indoor type cable end joints for the following size 1.1 KV gr., PVC insulated and PVC sheathed / XLPE Aluminium(Al)/ Copper(Cu) conductor armoured (Arm)/un armoured(un Arm) LT UG cables by employing necessary glands, terminals(Al/Cu), bolts & nuts etc., complete in all respects and as detailed below:
a) 4C x 16 Sqmm.Cu un arm LT cable. 10.00 Nos 0.00
b) 4C x 10 Sqmm.Cu un arm LT cable. 6.00 Nos 0.00
c) 3.5C x 70 Sqmm. Cu un arm LT cable. 6.00 Nos 0.00
d) 3.5C x 70 Sqmm. Al Arm LT cable. 14.00 Nos 0.00
e) 3.5C x 50 Sqmm.Al Arm LT cable. 5.00 Nos 0.00
f) 3.5C x 35 Sqmm.Al Arm LT cable. 5.00 Nos 0.00
g) 3.5C x 25 Sqmm.Al Arm LT cable. 5.00 Nos 0.00
h) 4C x 16 Sqmm.Al Arm LT cable. 6.00 Nos 0.00
i) 4C x 10 Sqmm.Al Arm LT cable. 6.00 Nos 0.00
j) 4C x 6 Sqmm.Al Arm LT cable. 5.00 Nos 0.00
k) 3C x 4 Sqmm. Cu Arm LT cable. 20.00 Nos 0.00
29 Supplying and making straight through joint with heat shrinkable kit including ferrules and jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required
a) 3.5C x 70 Sqmm. Al Arm LT cable. 1.00 No 0.00
b) 3.5C x 25-50 Sqmm.Al Arm LT cable. 1.00 No 0.00
c) 4C x 6-16 Sqmm.Al Arm LT cable. 1.00 No 0.00
30 Disconnecting and removing the following size existing LT cables from the existing LT panels and lifting from the cable duct/cable trench as-is-basis without damaging the cable, re-routing/re-laying the same as directed by Engineer-in-charge including testing & commissioning of the cable complete in all respect. Note:- 1)For cables which are to be laid in existing cable duct/pullout chamber/cable tray: scope includes removing exiting Precast concerte slab/ falls ceiling panels/ Chequerred plate and refixing of same after laying of cable including chipping and reconcereting to match with existing fiinish complete in all respect. 2)Cable end termination will be measured separately.
a) Upto 35Sqmm LT cables 200.00 Mtrs 0.00
b) Above 35Sqmm and upto 95 sqmm LT cables 100.00 Mtrs 0.00
c) Above 95Sqmm and upto 185 sqmm LT cables 100.00 Mtrs 0.00
a) Supply, Fixing, in flush with wall/on wall as per site condition, suitable size modular GI box/PVC box with base plate, glossy front cover for supply and housing of 1 No. of Twin RJ-11 telephone socket outlets with shutter including supply of suitable size modular type GI concealed/open PVC mounting box with base plates, front covers, etc., with necessary interconnections and chipping the wall, replastering to smooth finish etc., wherever required complete as directed by Engineer-in-charge. 1.00 No 0.00
b) Supply & drawing of 0.5 mm dia copper conductor PVC insulated 4 pair colour coded and twisted unarmoured telecommunication cables in the existing PVC conduit as per standard practice including necessary inter connections & end terminations. 1400.00 Mtrs 0.00
c) Supply, laying in the already excavated cable trench/existing duct/fixing on wall/cable tray/ steel structure using suitable clamps etc./ encasing in pipe, testing and commissioning of 50 pair jelly filled armoured copper conductor of 0.5mm dia polyethylene insulated cover, twisted into pairs, colour coded, pairs laid up, fully filled with petroleum jelly as a moisture barrier, core wrapped with non-hygroscopic polyester tape to contain the jelly, covered with aluminium poly-laminates screen, polyethylene sheath extruded over aluminium screen, polyethylene tape over the above sheath, armoured with galvanised steel tape and outer polyethylene sheath underground telecommunication cable including both end terminations on the existing krone type junction box complete in all respects and as directed by EIC. 60.00 Mtrs 0.00
d) Supply, laying in the already excavated cable trench/existing duct/fixing on wall/cable tray/iron structure using suitable clamps etc./ encasing in pipe, testing and commissioning of 20 pair jelly filled armoured copper conductor of 0.5mm dia polyethylene insulated cover, twisted into pairs, colour coded, pairs laid up, fully filled with petroleum jelly as a moisture barrier, core wrapped with non-hygroscopic polyester tape to contain the jelly, covered with aluminium poly-laminates screen, polyethylene sheath extruded over aluminium screen, polyethylene tape over the above sheath, armoured with galvanised steel tape and outer polyethylene sheath underground telecommunication cable including both end terminations on the existing krone type junction box complete in all respects. 160.00 Mtrs 0.00
e) Supply & fixing on wall/grouted to floor upto 1200mm above ground level as per site requirement using suitable size MS angle iron frame work finished with two coats of enamel spray paint over a good primer 50 pair krone type telephone junction box with necessary mounting frame housed in suitable size FRP box with hinged lockable cover complete in all respects. Note:-50 pair krone type telephone connector will be measured separately. 1.00 No 0.00
f) Supply & fixing on wall/grouted to floor upto 1200mm above ground level as per site requirement using suitable size MS angle iron frame work finished with two coats of enamel spray paint over a good primer 20 pair krone type telephone junction box with necessary mounting frame housed in suitable size FRP box with hinged lockable cover complete in all respects. Note:-50 pair krone type telephone connector will be measured separately. 2.00 Nos 0.00
g) Supply & fixing in the existing junction box of 50 pair krone type telephone connector including necessary interconnections complete in all respects as directed. 1.00 No 0.00
h) Supply & fixing in the existing junction box of 20 pair krone type telephone connector including necessary interconnections complete in all respects as directed. 3.00 Nos 0.00
32 Supply & fixing in flush with wall/on Aluminium partition as per site condition, testing & Commissioning of 2nos of Single Module RJ-45 sockets for Two numbers of Data points in a 2 modular GI box/PVC box including supply of suitable size modular type GI concealed/open PVC mounting box with base plates, front covers, etc., with necessary interconnections and chipping the wall, replastering to smooth finish etc., wherever required complete as directed by Engineer-in-charge. 75.00 Nos 0.00
33 Supply and drawing in the existing PVC conduits / wall / above false ceiling, Cat 6 UTP 4-Pair cable including necessary interconnections complete for LAN & Internet point as directed by Engineer-in-charge. 7500.00 Mtrs 0.00
34 Supply, installation, testing & commissioning of Following LT Panels(PTA)
Design, fabrication, supply, installation, testing and commissioning of Indoor type LT Panels (PTA) suitable to be mounted on the wall/Duct/on M.S channel/angle frame work as per site requirement including M.S channel/angle frame work for erection of panel, with cable entry from bottom/top as per drawing coordination by EIC with removable gland plates with required knock-outs for incoming and outgoing cables. Panel shall be fabricated out of CRCA sheet steel folded and braced as necessary to provide a rigid support for all components,totally enclosed and degree of protection shall not be less than IP-54, multi-tier cubicle type formation with front hinged lockable doors for the individual feeders / compartments, preparation of surface and treatment by seven tank process, powder coated with approved colour for not less than 50 microns and all doors and covers shall be fully gasketed using good quality EPDM gasket and/or rubber strips, and to provide good quality locking arrangment, durable door opening & closing mechanism, Aluminium bus bars for three phases and neutral, bus bar insulators, heat shrinkable PVC sleeves etc., with necessary interconnections as specified in Technical specifications for electrical & mechanical works, comprising of following switchgear and accessories complete in all respects and as directed by Engineer-in-charge.
Note:-1) Current density shall not exceed 0.8A/sq.mm for Aluminium bus bars in LT Panel
2)All MCCBs in the LT panels shall be adjustable with thermal settings(80% to 100%), overload and short circuit releases including door interlocking device, front operating handle complete,ON and OFF indication of LED module etc. complete in all respects.
3)The operating height of the Panel shall not exceed 2.1 mtr. from FFL.
34.1 Supply, installation, testing & commissioning of LT Panel-1(PTA) at Electrical shaft ground, first & second floor. 3.00 Nos 0.00
i) 1-no 125A 415V gr 4P 36KA MCCB.
ii) Lot - 200A, 4P, 415V, short circuit rated 36KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.
iii) 1Nos- Multi function meter (MFM/MDM) suitable for 3ph, 4 wire, 240V(L-N), 5A, CL-1, RS 485 Port Digital MFM/MDM of EM6400NG of Schneider or any equivalent make meeting technical specification of above MFM complete in all respect.
iv) 1 Set-125/5A current transformers of suitable class and VA burden for metering.
v) 1no-(0-500V)range digital type Voltmeter with a push button option for selecting the phases.
vi) 1Set - RYB indicating lamps of LED module with 6A, 230V, 10KA, SP MCB.
vii) 1Set- 6A, 230V, 10KA, SP MCB for the protection of measuring instruments.
i) 10-Nos 63A 415V gr. 4P 10KA MCB.
ii) 10-Nos 32A 415V gr. 4P 10KA MCB.
iii) 10-Nos 32A 250V gr. DP 10KA MCB.
34.2 Supply, installation, testing & commissioning of LT Panel-2(PTA) at Electrical shaft Third floor. 1.00 No 0.00
i) 1-no 200A 415V gr 4P 36KA MCCB.
ii) Lot - 250A, 4P, 415V, short circuit rated 36KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.
iii) 1Nos- Multi function meter (MFM/MDM) suitable for 3ph, 4 wire, 240V(L-N), 5A, CL-1, RS 485 Port Digital MFM/MDM of EM6400NG of Schneider or any equivalent make meeting technical specification of above MFM complete in all respect.
iv) 1 Set-200/5A current transformers of suitable class and VA burden for metering.
v) 1no-(0-500V)range digital type Voltmeter with a push button option for selecting the phases.
vi) 1Set - RYB indicating lamps of LED module with 6A, 230V, 10KA, SP MCB.
vii) 1Set- 6A, 230V, 10KA, SP MCB for the protection of measuring instruments.
i) 1-No 100A 415V gr. 4P 10KA MCCB.
ii) 10-Nos 63A 415V gr. 4P 10KA MCB.
iii) 10-Nos 32A 415V gr. 4P 10KA MCB.
iv) 10-Nos 32A 250V gr. DP 10KA MCB.
34.3 Supply, installation, testing & commissioning of LT Panel-3(PTA) at Stair case area all floor. 4.00 Nos 0.00
i) 1-no 125A 415V gr 4P 36KA MCCB.
ii) Lot - 200A, 4P, 415V, short circuit rated 36KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.
iii) 1Nos- Multi function meter (MFM/MDM) suitable for 3ph, 4 wire, 240V(L-N), 5A, CL-1, RS 485 Port Digital MFM/MDM of EM6400NG of Schneider or any equivalent make meeting technical specification of above MFM complete in all respect.
iv) 1 Set-125/5A current transformers of suitable class and VA burden for metering.
v) 1no-(0-500V)range digital type Voltmeter with a push button option for selecting the phases.
vi) 1Set - RYB indicating lamps of LED module with 6A, 230V, 10KA, SP MCB.
vii) 1Set- 6A, 230V, 10KA, SP MCB for the protection of measuring instruments.
i) 6-Nos 63A 415V gr. 4P 10KA MCB.
ii) 6-Nos 32A 415V gr. 4P 10KA MCB.
iii) 10-Nos 32A 250V gr. DP 10KA MCB.
34.4 Supply, installation, testing & commissioning of AC Indoor units LT Panel (PTA) at Electrical shaft 3rd floor. 1.00 No 0.00
i) 1-No 63A 415V gr 4P 36KA MCCB.
ii) Lot - 200A, 4P, 415V, short circuit rated 36KA for 1sec, Aluminium bus bars with busbar insulators, heat shrinkable PVC sleeves etc.
iii) 1No-(0-500V)range digital type Voltmeter with a push button option for selecting the phases.
iv) 1Set - RYB indicating lamps of LED module with 6A, 230V,10KA, SP MCB.
v) 1Set- 6A, 230V, 10KA SP MCB for the protection of measuring instruments.
i) 18 Nos - 32A 250V gr DP 10KA MCB
35 Supply and fixing on wall/ partition wall using necessary mounting arrangements for 105/100x50mm size DLP-PVC adaptable trunking system with separation partition for laying power and Data/Telephone cables/wires with full top cover, necessary accessoires such as end caps, flat angle, T joints, external/internal angle, flat junction, Body joint, cover joint, required cabling accessories etc., complete in all respects as directed by Engineer-in-charge. 120.00 Mtrs 0.00
36 Supply and fixing on wall/on Aluminium partitoins / floor / above false ceiling of 32X16 mm dia DLP mini plastic trunking of OBO/LEGRAND/MK INDIA/SCHNEIDER halogen free, including necessary accessories such as end caps, tees, joints, bends, Covers, bends, dividers, reducers, junction boxes,etc., as required as per site conditions and as directed by Engineer In-charge. 50.00 Mtrs 0.00
37 Supplying and fixing of Hot dip galvanised Perforated type cable tray of following sizes, steel: As per IS:2062 / 1079, Galvanising : As per IS: 2629 / 4759 including all accessories like base slotted angle , horizontal elbow, horizontal tee, horizontal cross, horizontal reducer, vertical elbow up, inside, vertical elbow down, outside, coupler plate, fasteners etc., and duly suspended from the ceiling/fixing to the wall/RCC beam/iron structures upto a height of 3/4mtrs from FFL., complete in all respects and as directed by Engineer in charge
a) Supplying and fixing of 200/225 x 50 x 1.6mm size Hot dip galvanised Perforated type cable tray 200.00 Mtrs 0.00
b) Supplying and fixing of 300 x 50 x 1.6 mm size Hot dip galvanised Perforated type cable tray 160.00 Mtrs 0.00
c) Supplying and fixing of 600 x 50 x 2 mm size Hot dip galvanised Perforated type cable tray 35.00 Mtrs 0.00
38 Supply & drawing/laying of 2C X 6 Sqmm PVC insulated 1100V gr. flexible multi stranded Copper cable with ISI mark for DB's earting using suitable copper lugs including necessary interconnections, clamps & hardwares complete as directed by Engineer -in-charge. 100.00 Mtrs 0.00
39 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. 10.00 Nos 0.00
a) Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. 2.00 Nos 0.00
b) Supplying & laying 25 mm X 5 mm GI strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of GI nut bolt & spring washer spaced at 50mm) 120.00 Mtrs 0.00
c) Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 100.00 Mtrs 0.00
41 Supply, fixing on wall using suitable angle iron frame work, testing and commissioning of the following capacity powder coated, Switch disconnector fuse unit with equal rating DIN type HRC fuses, front operating handle, door interlocking system, ON and OFF indication using LED module etc. enclosed in sheet steel enclosure, including suitable cable end box wherever necessary complete in all respects and as directed by Engineer-in-charge.
a) Supply,installation, testing and commissioning of 125A, 4 pole, 415Vgr. SDFU, 3.00 Nos 0.00
b) Supply,installation, testing and commissioning of 200A, 4 pole, 415Vgr. SDFU, 1.00 No 0.00
a) Supply and fixing of floor Mountable 22U Network Rack with Power Distribution unit and Dual cooling Fan, earthing cable etc. with all standard Accessories, complete in all respects as per technical specification and as directed by Engineer-in-charge. Approved. Make:APC/VALRACK/NETRACK/RITTAL 1.00 No 0.00
b) Supply and fixing of wall Mountable 15U Network Rack with Power Distribution unit and Dual cooling Fan, earthing cable etc. with all standard Accessories, complete in all respects as per technical specification and as directed by Engineer-in-charge. Approved Make:APC/VALRACK/NETRACK/RITTAL 1.00 Nos 0.00
c) Supply and fixing of Loaded, 24 Port CAT6 UTP Jack Panel, complete in all respects as per technical specification and as directed by Engineer-in-charge. Approved Make:COMMSCOPE TYCO/ PANDUIT/ MOLEX 3.00 Nos 0.00
d) Supply and fixing of Loaded, 48 Port CAT6 UTP Jack Panel, complete in all respects as per technical specification and as directed by Engineer-in-charge. Approved Make:COMMSCOPE TYCO/ PANDUIT/ MOLEX 3.00 Nos 0.00
e) Supply and fixing of Cat 6 UTP 4-Pair 0.5Meter length Patch cord, complete in all respects as per technical specification. Approved Make:COMMSCOPE TYCO/ PANDUIT/ MOLEX 72.00 Nos 0.00
f) Supply and fixing of Cat 6 UTP 4-Pair 1Meter length Patch cord, complete in all respects as per technical specification. Approved Make:COMMSCOPE TYCO/ PANDUIT/ MOLEX 130.00 Nos 0.00
43 Disconnecting/dismantling & removal of the following items as-is-basis without any damage and handing over the same to the place as shown by Engineer-in-charge including loading, transportation, unloading etc., complete in all respects. The scope also includes disconnecting the existing cables from panel, complete in all respects and as directed by the engineer-in-charge. at Ground & third floor finance dept. & corridor 1.00 LS 0.00
i)Disconnecting & dismantling of 100nos 1/2 x 28/36/40W Tube light fittings including removing of wiring.
ii)Disconnecting & dismantling of 25nos (2x2) 36/72W light fittings/ including removing of wiring.
iii)Disconnecting & dismantling of 50Nos ceiling Fans including removing of wiring.
iv)Disconnecting & dismantling of 10Nos Wall Mounting Fan/exhaust/aircirculator fans including removing of wiring.
v)Disconnecting & dismantling of LT cables-1)3/3.5CX6-50sqmm Al Arm cable-300Mtrs.
vi)Disconnecting & dismantling of Lan & Telephone cables-4000Mtrs.
vii)Disconnecting & dismantling of 440V Cubicle/industrial type MCCB's/SFU's/DB's enclosure-10Nos
viii)Disconnecting & dismantling of 440V Cubicle type LT Panel comprising of MCCB's/SFU's-4Nos
44 Removing, re-fixing & re-connecting the existing smoke/heat detectors using new wiring at Ground & Third floor including required fixing accessories and necessary connection complete in all respects as directed by EIC. (Wiring will be measured separately) 52.00 Nos 0.00
45 Removing, re-fixing & re-connecting the existing response indicators using new wiring at Ground & Third floor including required fixing accessories and necessary connection complete in all respects as directed by EIC. (Wiring will be measured separately) 7.00 Nos 0.00
46 Removing, re-fixing & re-connecting the existing Manual Call Point using new wiring at Ground & Third floor including required fixing accessories and necessary connection complete in all respects as directed by EIC. (Wiring will be measured separately) 6.00 Nos 0.00
47 Removing, re-fixing & re-connecting the existing Electronic Hooter cum Flasher using new wiring at Ground & Third floor including required fixing accessories and necessary connection complete in all respects as directed by EIC. (Wiring will be measured separately) 6.00 Nos 0.00
48 Supply, laying and fixing directly to the ceiling/on wall / above false ceiling etc, testing & commissioning of 2 Core X1.5 sqmm copper XLPE insulated FRLS with ISI mark armoured RED/Black colour LT cable as per site requirement along with required accessories, terminations glands, as directed by EIC to complete the installation as per the technical specification.(Fire alarm work) 300.00 Mtrs 0.00
Sub-Total of Part PART IIA - ELECTRICAL, VOICE & DATA WORKS (Excluding GST) 0.00
PART II B - Airconditioning Works
Airconditioning Works
1 Design, Supply, erection, testing and commissioning of 14HP capacities Air-cooled variable refrigerant volume/variable refrigerant flow(VRV/VRF) modular type Outdoor unit mounted on suitable MS angle frame for connecting multiple indoor units of different capacities including suitable size communication copper control wiring up to each indoor units, minimum two energy efficient inverter driven rotary/ Scroll compressors 3 phase, 380-415 V, 50Hz AC power supply input including microprocessor control panel, starter controls for all compressors and condenser fan motors along with internal control and power wiring, cooling coil with internally interconnected refrigerant pipes for interconnecting various capacity modules , charging port and the entire unit shall be with weather resistant powder coating paint for withstanding for continuous outdoor operation, all other required accessories, & hardware’s, full charge of eco friendly R 410A/R407 /R32 Refrigerant, safety devices and all other standard accessories etc., complete in all respect as per technical specification and as instructed by the Engineer-in-charge. MS frame work for mounting unit will be included in the scope. Note: 1)Power supply to 14HP unit will be provided near ODU. Contractor have to tap power supply from this to respective control panel. 1.00 Set 0.00
2 Design, Supply, erection, testing and commissioning of following Four directional/ Rounded air flow Cassette type Indoor Air Conditioning Units of following capacity suitable for mounting inside false ceiling, each comprising of cooling coil, blower with multi speed motor, electronic expansion valve, supply & return air grilles, filter, insulated connection of refrigerant circuit, provision for fresh air intake, condensate water drain pump with electronic level sensor, including necessary cutting of false ceiling and suitable size LT copper cable connecting to the nearest existing plug & socket, necessary mounting arrangement for suspending the unit from ceiling etc. All the indoor units shall be compatible to work with VRV / VRF type condensing unit. Scope includes Remote controller (Cordless) including batteries. Note: Power supply to individual indoor unit will be tapping from nearest power point provided under electrical scope of work.
a Minimum 1.0 TR capacity Cassette type unit having 4 way / rounded uniform air flow as required. 6.00 Nos 0.00
b Minimum 1.5 TR capacity Cassette type unit having 4 way / rounded uniform air flow as required. 2.00 Nos 0.00
c Minimum 2.0 TR capacity Cassette type unit having 4 way / rounded uniform air flow as required. 1.00 No 0.00
3 Design, Supply, erection, testing and commissioning of suitable size refrigerant copper pipe with required bends and couplings by good quality pipe joints which laid between IDU and ODU . The Minimum copper pipe gauge shall be as per the gauges indicated by manufacturer. The Pipe sizes to be used as per manufacturer design recommendation. The Refrigerant pipe shall be insulated with Class O nitirle rubber of 19 mm thick for Gas line and 19 mm thick for liquid line. The piping shall be laid on walls / roof / ceiling well supported at specific intervals with metallic supports screwed with anchor fasteners. All the necessary accessories, jointing / brazing etc shall be carried out as required. All piping inside the ceiling shall be properly supported using necessary clamps. The pressure testing of refrigerant piping has to be done as per manufacturer design recommendation. 120.00 Rmtrs 0.00
All the copper fittings shall be suitable for R 410 A/R 407/R-32 refrigerant. Refer IDU/ODU layout tender drawing . Make: Mandev/Piyush/Totaline (Note: 1. Irrespective of diameter both gas and liquid piping shall be measured as a single item. The single item measurement comprising of gas line, liquid line, insulation and its accessories. Contractor make a note of it and quote accordingly. 2. Before commencement of work, shop drawing to be submitted to OIC/EIC for approval. 3. Scope of work includes charging of refrigernt after completion of piping network before commissioning of plant. 4. Piping inside the building to be clamped to ceiling using suitable clamp. Cost of clamp & hardwares to be included in the scope work. Only piping coming out side the building will be fixed to existing cable tray. 5. Necessary wall openings and closing the same using cement mortar and matching paint finish after taking out pipes is included in the scope of work.
4 Design, Supply, erection, testing and commissioning of variable refrigerant flow distribution REFNETS (Y – Joints) in the suction & liquid lines as per manufacturer design for IDU/ODU. 8.00 Nos 0.00
5 Design,supply,Installation testing & commissioning of suitable sizes as per OEM recommonadation not less than 2mm thick CPVC drain water / fresh air arrangement pipe including reducer, bends, collars & elbow etc, all complete and duly insulated with 9 mm thick tubular insulation of closed cell elastomeric nitrile rubber as required.The PVC drain water pipe/fresh air pipe shall be complete with fittings, accessories and duly insulated using bends, elbows, tees, wall sleeves, hangers, supports, anchors etc.(Note:.1 Pipe used for fresh air intake to IDU shalll be coverd with mesh. 2. Necessary wall openings and closing the same using cement mortar and matching paint finish after taking out pipes is included in the scope of work. ) Make: Supreme/Finolex/Hycount/Saroplast 100.00 Rmtrs 0.00
Sub-Total of Part IIB-Airconditioning Works (Excluding GST) 0.00
Total of Part 'I' + 'II A' +'II B' (Excluding GST) 0.00
Add 18% GST 0.00
Grand Total (Including GST) 0.00
HINDUSTAN AERONAUTICS LIMITED
Facilities Management Division
Pre-Qulification Profile (To Be uploaded along with Part A)
Tender Ref No. or Contract No.: HAL/FMD/C-64/24-25
Name of Work: Renovation of Ground Floor and Part of Third Floor at Corporate Office, Bangalore.
Estimated Amount in lakhs.: 33070000
Tender Notice Date:(DD/MM/YYYY) 21.09.2024 Can we give in DD/MM/YYYY
Complition Period(In months) 6
PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3 Kindly mention at Col I J &K as " Any Other related Information"
Sl.No Description Details Enclosed / Not Enclosed Any Other Related Information Remarks
1 Name of the Individual / Firm / Company: * Mandatory Pls enter name
2 Type of ownership Related Document to be Uploaded to eProcurement Portal
3 Year of Estblishment of Company/Business
4 If Other, please specify
5 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, etc., If not enclosed reasons be to recorded here
6 Address for correspondence:
8 PAN no and Name of Holder
9 PF number (If any)
11 (a) Service Tax Registration No
11 (b) Goods and Service Tax ID No.
12 Contact details
Contact person name Pls
Ph. No. with STD code
FAX No. with STD code 5 6
13 Registered Contractor
If Registered Contractor with HAL Yes/ No Pls Enter Related Document to be Uploaded to eProcurement Portal * Category: A = Above 25 Crores B = 15Crore to 25 Crores C = 5Crore to 15 Crores D = 1 Crore to 5 Crores E = Lessthan 100 Lakhs to 75 Lakhs F = 75 Lakhs to 50 Lakhs 0 7 .A1 1
Name of Organisation 199999 7 A 2
Category and Registration No. 200000 6 B 3
PEMD Amount ( If paid ) 499999 6 C 4
not required Need to Fill Column 19 no comparision 500000 5 D 5
14 I.T Returns for past 03 years 999999 5 E 6
2023-24 Pls Select 'Yes','No' for IT Returns for all the 3 years 2499999 4
15 Maximum value of works excuted during the followinf 5 years. . (In Lakhs)
2018 - 2019 Pls enter Finiancial Turnover in Rupees for all the years NOTE: The value of max work to be supported with the details of Works executed for each year including name of the organisation with period of execution. Here last 3 years cells to be considered to Check Annual Turn Over for 30 % value of Estimation given above 1 6.00 7.00 0 0
Avg Annual Turnover criteria is not met
16 DETAIL OF WORK ON HAND UPTO N-Months (N-contract period) [For Bid capacity calculation] NOTE : PROVISION for 10 works are given. If more, a separate similar sheet to be made showing all the works with all details as per this FORMAT and same to Uploaded. However, 9 works details to be provided and balance work value of other works to be added and to be provided in 10th row as OTHER works.
Sl.No(work No) Name of Organization with address Name of the work on hand Amount of Contract Rs (in Lakhs) Period of CONTRACT in months Date of Commencement of work as Work Order in dd/mm/yyyy Probable date of Completion as Agreed Actual progress achieved till date of Tender Notification Rs (in Lakhs) Balance value of work on hand [Col.(3)-Col.(7)] Rs (in Lakhs) Remarks If Any 0.00
8 0.00 Max Turn Over 07-08 8500000
9 0.00 Current Level to be brought by adding 10% for every year 10-11 8500000 X 1.1 X 1.1 X 1.1
10 0.00 Turn Over to considered A 11313500
0.00 Balance Work On Hand 207452000
Bid Capacity 0.00 Bid Capacity Criteria is not Met this shouldf be hidden while uploading
17 Work Schedule for completion of works with in stipulated time [Please enclose action plan / bar chart as to indicate the completion of work, within the scheduled time (contract period)] Bid Capacity (2 X A X N) - B
Related Document to be Uploaded -162198000
18 Quantity of work Excuted during the last three years
Earthwork [in Cum]
Concrete work [in Cum]
Reinforcement steel [in MT]
Any other quantity of items tenderer would like to mention
19 Bank(s) details: [Copy of the cheque leaf to be uploaded]
19a Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)
Name of the Bank
Type of Account
19b Bank Statement for past three month
19c Latest Over draft Facilties with Bank enter Name of Bank, Date of Issue and Value of Over Draft
20 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the date of Tender Notice. SOLVENCY solvency cal
Name of Bank & Branch Pls Related Document to be Uploaded to eProcurement Portal 21.09.2024 1-Jul 0 40000
Date of Issue(dd-mm-yyyy) #VALUE! 200000 40000
Value Rs. In Lakhs 200001 150000
Solvency value is as per NIT
21 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Work experience certificates / Completion certificates should be uploaded for verification]. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of the estimated cost. [Amount put to the Tender] 2000000 500001 250000
Completed similar works during last 7 years You are Not Eligible Pls Select Works Completed during last 7 years 1000000 250000
Work NoI Type of Work [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000
Name of The organisation
Brief Description of Work: 2000000 500000
Completed value of Work in Rs. Lakh: 2000001 1000000
Date of Commencement of Work [DD/MM/YYYY]: 4000000 1000000
Date of Actual Completion of Work[DD/MM/YYYY]: 4000001 2000000
Work No II Type of Work [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000
Name of The organisation
Brief Description of Work
Completed value of Work in Rs. Lakh:
Date of Commencement of Work [DD/MM/YYYY]:
Date of Actual Completion of Work[DD/MM/YYYY]: work done
Work No III Type of Work and Organisation name [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 21.09.2024 2555
Name of The organisation
Brief Description of Work: #VALUE!
Completed value of Work in Rs. Lakh:
Date of Commencement of Work [DD/MM/YYYY]:
Date of Actual Completion of Work[DD/MM/YYYY]:
Work Competion is NOT with in 7 years
Valid Class I Electrical Licence [or] Undertaking for engaging Electrical Contractor possessing valid Class I Electrical Licence Please Enter Electricial Licence No Electricial Licence valid upto Related Document to be Uploaded to eProcurement Portal
22 DEAILS OF TECHNICAL PERSONNEL AVAILABLE( if space provided is insufficant separate sheet to be uploaded with the same format as below)
Sl.No Name of members or technical personllel avalable in the organization Qualification of similar nature number of years of experience
23 DETAILS OF MACHINERY AVAILABLE
Sl.No Name of Mechinery No Make Year of Manufacture
1 Concrete Mixers - Type etc
2 Vibrators - Diesel - Electrical
3 Weiding equipment's
4 a) Rectifiers
5 b) Welding Generators
6 Erection equipment's
10 Water Lifting motor pumps
13 Drilling Equipment's
16 Stone crushers
17 Bitumen hot mixture plant
18 Bitume boiler
20 Batching plants
21 Vibratory rollers
23 Cranes-Details
24 Concrete pumps
26 Rock breakers
27 Transit mixers
29 Weight batches
24 Details of person holding the power of Attorney (If different from contact person)
Name Related Document to be Uploaded to eProcurement Portal
Ph. No. with STD code
FAX No. with STD code
I/We declare and confirm that - 1. All information and attachments submitted in this application are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my application and suspension of any registrations granted. 3. I/We shall not make refund claims of expenditure incurred in processing this application. Pls enter
26 Tender Document Cost and EMD details
Descipttion Enclosed / Not enclosed Valid upto [in case of BG] Related Document to be Uploaded to eProcurement Portal
Tender cost Enclosed
27 Average annual financial turn over during the last 3 years, ending 31st March 2023 [ should not be less than 30% of amount put to tender] and details for last 5 years to be provided to assess the bid capacity. The values provided to be supported by uploading Balance Sheet along with Profit & loss account statement. . (In Lakhs)
2022-23 Pls Select 'Yes','No' for Annual financial turn over for all the 3 years
Average 0.00 FALSE
Balance sheet and Profit & loss statement for last 05 years
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
raw.json
RAW_JSON
TN30.pdf
TENDER_DOCUMENT • 1.16 MB
CivilTenderDrawing04.pdf
TENDER_DOCUMENT • 0.21 MB
CivilTenderDrawing03.pdf
TENDER_DOCUMENT • 0.35 MB
64Undertaking.pdf
TENDER_DOCUMENT • 0.57 MB
CivilTenderDrawing01.pdf
TENDER_DOCUMENT • 0.29 MB
ElectricalTenderDrawing02.pdf
TENDER_DOCUMENT • 0.43 MB
ElectricalTenderDrawing06.pdf
TENDER_DOCUMENT • 0.14 MB
ElectricalTenderDrawing07.pdf
TENDER_DOCUMENT • 0.39 MB
64PQ.pdf
TENDER_DOCUMENT • 0.21 MB
ElectricalTenderDrawing01.pdf
TENDER_DOCUMENT • 0.35 MB
64TB.pdf
TENDER_DOCUMENT • 4.05 MB
64PBF.xlsm
TENDER_DOCUMENT • 0.08 MB
64PB.pdf
TENDER_DOCUMENT • 0.56 MB
ElectricalTenderDrawing05.pdf
TENDER_DOCUMENT • 0.26 MB
64PQF.xlsm
TENDER_DOCUMENT • 0.04 MB
ElectricalTenderDrawing04.pdf
TENDER_DOCUMENT • 0.26 MB
Amendment.pdf
TENDER_DOCUMENT • 0.09 MB
ElectricalTenderDrawing03.pdf
TENDER_DOCUMENT • 0.29 MB
64ECSForm.pdf
TENDER_DOCUMENT • 0.48 MB
64Checklist.pdf
TENDER_DOCUMENT • 0.19 MB
CivilTenderDrawing02.pdf
TENDER_DOCUMENT • 0.21 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .