NIT-09

Amount

SCHEDULE 'A' PART-I : BOQ OF WORKS FOR B/R WORKS.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and as directed by Engineer-In-Charge.

Rendering 15mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:6, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-In-Charge.

Dismantling of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and as directed by Engineer-In-Charge.

Brickwork with subclass ‘B’ bricks, old size bricks, straight or curved on plan exceeding 6.0mtrs mean radius built in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

Description all as per serial item No- 1.04 here-in-before but except bricks .

Preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of chalk whiting, on plastered surfaces, preparatory to distempering, complete all as specified and as directed by Engineer-In-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement paint over one coat lime wash, complete all as specified and as directed by Engineer-In-Charge.

Repalcement of broken tiles with new non-skid, matching to existing colour, ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, fixing in repairs of floors in pacth work. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including laid over screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6, complete all as specified and as directed by Engineer-In-Charge.

Plain cement concrete M-15(1:2:4), type B-1, (using 20mm graded crushed stone aggregate), nominal mix, as in copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work, complete all as specified and as directed by Engineer-In-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed by Engineer-In-Charge.

Sheet glass, 3.0mm thick, ordinary quality and glazing with oil putty or with wooden beadings, fixing in square not exceeding 0.50Sqm in each pane, complete all as specified and as directed by Engineer-In-Charge.

Sheet glass, 3.0mm thick, sheet glass, sheet glass is ground or obscured or frosted on one side and glazing with oil putty or with wooden beadings, fixing in square not exceeding 0.50Sqm in each pane, complete all as specified and as directed by Engineer-In-Charge.

Aluminium handles, cast type, anodised, size 150mm, complete all as specified and as directed by Engineer-In-Charge.

Aluminium anodised, barrel tower bolts of extruded Section, size 200mm long and fixed, complete all as specified and as directed by Engineer-In-Charge.

Aluminium alloy, anodised, sliding door bolt, size 250mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed by Engineer-In-Charge.

Aluminium alloy, anodised, sliding door bolt, size 300mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed by Engineer-In-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, cverall length of cover plate 140mm, fixed in floor, complete all as specified and as directed by Engineer-In-Charge.

Mild steel spring for doors, 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed by Engineer-In-Charge.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, fixed in repairs, complete all as specified and as directed by Engineer-In-Charge.

Resecuring or easing and adjusting with out taking down shutters of any descriptions, area exceeding 1.00 Sqm but not exceeding 2.00 Sqm and re-fixing in the same openning, complete all as specified and as directed by Engineer-In-Charge.

Resecuring or easing and adjusting with out taking down shutters of any descriptions, area not exceeding 1.00 Sqm re-fixing in the same openning, complete all as specified and as directed by Engineer-In-Charge.

Taking up or down steel tubing of 15mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed by Engineer-In-Charge.

Tubes, 'medium grade' galvanised, 15mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Old tubes, 'any grade' galvanised, 15mm bore, with all new fittings such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Taking up or down steel tubing of 20mm bore pipe and connections, including cleaning for re-fixing or removal to store, complete all as specified and as directed by Engineer-In-Charge.

Tubes, 'medium grade' galvanised, 20mm bore, ISI marked with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

Old tubes, 'any grade' galvanised, 20mm bore, with all new fittings such as bends, tees, elbows, unions, short pieces, connectors, back nuts, etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-In-Charge. Note: Cost of cutting/ chasing for pipe line making concealed in surfaces shall be deemed included in quoted rates.

PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, capacity 10.0 litres and making good to dismantled/ damaged floor/ surfaces, fixing in repair, complete all as specified and as directed by Engineer-In-Charge.

Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern, complete all as specified and as directed by Engineer-In-Charge.

PVC connections 15mm size with brass nuts of length 450mm, complete all as specified and as directed by Engineer-In-Charge.

Bib taps, long body, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Bib taps, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Bib taps, 2-way, with wall flange and aerator, cast copper alloy, chromium plated, fancy type, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No- F3002211 of Cera/ Jaquar/ Parko/ Hindware.

Stop valves, 2-way, cast copper alloy, chromium plated, fancy type, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No- F3002211 of Cera/ Jaquar/ Parko/ Hindware.

Bib tap, long body, standard of PTMT any colour high pressure screwed for iron pipe and fixed for 15mm bore pirpe, (Minimum weight 15mm-120gms), fixing in repairs, complete all as specified and a sdirected by Engineer-In-Charge.

Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed for 15mm bore iron pipe (Minimum weight 15mm-90gms), fixing in repairs, complete all specified and as directed by Engineer-In-Charge.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed for 15mm bore pipe, fixed in repair, complete all as specified and as directed by Engineer-In-Charge.

Angle valve/ cock, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Angle stop valve of PTMT any colour, with long shank and cup (concealed type), high pressure screwed for iron pipe and fixed for 15mm bore pipe, (Minimum weight 15mm-110gms), fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Brass chromium plated shower rose 150mm square size, fancy type, fixed for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No- F7010506 of Cera/ Jaquar/ Parko/ Hindware.

Low density polyethylene (LDPE) pipes of pressure rating 6.0 kgf/Sqcm, 32mm bore and 900mm long, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges, brass chromium plated, fancy type, including end brackets, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Tubular towel ring 20mm dia, brass chromium plated, universal type, including end brackets, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Rotational moulded polyethylene water storage tanks of 1000 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Rotational moulded polyethylene water storage tanks of 500 liters capacity, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

PVC valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 20mmbore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

PVC valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed for 15mmbore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Waste coupling of PTMT (half or full threaded) for 32mm bore/ dia of discharge pipe, complete all as specified and as directed by Engineer-In-Charge.

PVC (SWR) pipes, 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-In-Charge.

Brass chromium plated hat and coat hooks, solid body, 175mm to 250 mm including screws of same metal, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Glass corner shelf, made with 6 to 8mm thick transparent glass, three teirs including anti rust screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Hand shower (Health faucet), ABS body with 8mm dia and 1.0mtrs long SS braided flexible tube with wall hook, complete all as specified and as directed by Engineer-In-Charge. Make: Cera cat part No- F8030101 or equivalent in Orient/ Jaquar/ Riviera.

Soap dish, fancy type, fixed to plugs with chromium plated brass screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Toilet paper holder, fancy type and chromium plated, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Sinks with drainage board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm, including waste coupling, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Plate rack (kitchen stand) stainless steel, size 760x910x230mm, thickness of stainless steel sheet not less than 0.80mm, weight not less than 8.00Kg each, fixing by means of electrical drill machine, fasteners and screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Basin mixer for hot and cold water, chromium plated, for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No-F3001461 of Cera/ Jaquar/ Parko/ Hindware.

Waste coupling of brass chromium plated (half or full threaded) for 32mm bore dia of discharge pipe, complete all as specified and as directed by Engineer-In-Charge.

Wall mixer with bend pipe for overhead shower with built-in non return valve, for hot and cold water, chromium plated, for 15mm bore pipe, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge. Make: Cat Part No- F1003403 of Cera/ Jaquar/ Parko/ Hindware.

Water storage tank lid, PVC lid , suitable for rotational moulded polyethylene water storage tanks of 500/ 1000 liters capacity, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Stainlees steel grating, chromium plated, size 125mm, heavy duty, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Sheet glass shelf assembly, consisting 5.50mm thick sheet glass, 120mm wide including anti rust screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Door seal metallic, powder coated, at least 25mm in wide and 1.0mtr in length with nylon fibre brussels, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and as directed by Engineer-In-Charge.

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) door/ window shutters, aluminium section weighing 0.55 Kg/mtr including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc and fixing 5.50mm thick plain glass sheet with rubber packing/ beading, complete all as specified and as directed by Engineer-In-Charge. Note : Cost of Glass and other filling material in panels shall be deemed included in quoted rate.

Anodised aluminium powder coated (minimum thickness of powder coating 50micron) sliding door shutters with frame section size 65mmx37mmx1.50mm with door handle locking system (Godrej/ Link/ Harrison), shutters frame weighing 0.55 Kg/mtr including necessary joining cleats, glazing clips, ruber neoprene packing, 150mm long handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc and fixing 5.50mm thick plain glass sheet with rubber packing/ beading, complete all as specified and as directed by Engineer-In-Charge. Note : Cost of door frame, shutter, glass and other filling material in panels shall be deemed included in quoted rate.

Anodised aluminium powder coated grills of any size, pattern and any aperture, complete all as specified and as directed by Engineer-In-Charge. Note: Weight of grill per square meter shall be decided by BOO for payments.

Door closer, aluminium extruded body section, hydraulically regulated, designation No-01, universal type, suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Curtain rod, 20mm dia, mild steel, fancy type, any colour coated with fixing and inlcuing end knobs, fixing brackets, stops, round rings to hold the curtain, fixing in repairs with wall plugs and screws, complete all as specified and as directed by Engineer-In-Charge.

Mild steel flat clamps, colour coated decorative types, made to shape to hold the curtain rods with wall plugs and screws, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

PTMT end knobs, colour coated decorative types, suitable for curtain rod's ends, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Mild steel handle for steel windows of any type, size 100mm, including fixing with welding/ rebating at site, fixing in repairs, complete all as specified and as directed by Engineer-In-Charge.

Mild steel stay arm for steel windows of any type, including fixing with welding/ rebating at site, complete all as specified and as directed by Engineer-In-Charge.

Amount of Schedule of credit of for Rs 39,430.00 shall be deducted from quoted amount.

M/S JEEVAN LAL SHARMA

CHOPRA CONSTRUCTIONS