Renovation of IIS Department at 3rd floor of Admin Building of NRL Site, Numaligarh

Amount

Providing and fixing 12 mm thick WPC board on WPC frames with all necessary fittings and fixing wherever necessary and as per the direction of E.I.C.

Providing and fixing WPC customised sections for frame work of cubicles and partitions size (90x90)mm including all necessary fittings and fixing.

Providing & applying Duco paint finish on WPC members with phospate coat primer, solid paint white satin finish and clear coat one part and two part formulations are often referred to as 1k and 2k respectively.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound,jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66mm overall thickness Partition with 8mm thick double skin(both side of the frame) Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./ sq.cm all complete as approved & directed by Engineerin-Charge .

Providing and fixing in position glass partition with 12mm thk toughned glass of saint gobian/Pilinkton/Modiguard make fixed to the frame rigidly and at centres wherever required in line and level with SS patch fittings of DORMA/OZONE/HAFELLE make with all enabling works complete as per drawing and direction of EIC

Supply and installation of false ceiling as per the architectural drawings (plan and sections) with Silhouette 15 mm exposed grid system (ISI marked) of 600x600 mm module shall include wall angles with unequal flanges of size 14&20 mm and 0.40 mm thick (minimum dimensions) fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300 mm center to center. The main member, having flange width 15 mm, height 30 mm (minimum dimensions) should be suspended from the immediate roof with help of soffit cleat and wire rod etc. and leveling spring clip at 1200 mm c/c or as required. Cross member having flange width 15 mm, height 30 mm (minimum dimensions) are to be fixed and interlocked into the pre-cut slots in the main member at 600 mm c/c in the perpendicular direction.The cross silhouette having flange width 15 mm, height 30 mm (minimum dimensions) are then interlocked into the pre-cut slots at 1200 mm c/c in parallel direction to the main member. Steppe edged acoustical board of 15 mm thick (minimum) shall be placed into the grid size of 600x600 mm properly with necessary clips and other accessories as required. The size of the board should be 595x595. The work should be executed in accordance with the drawing and prior necessary discussion with electrical, A/C installation team and other vendors as required. Finished and complete in all levels/respects as per the directions of Engineer In-charge. Technical Parameters of Ceiling Board : The board should contain at least the following properties. a) Non metallic Acoustical Board: • Core - Glass fibre/ Mineral fibre • Fire Resistant: 1/A Class Fire Rated. • Acoustical property – NRC; 0.70 to 0.85 • Termite resistance • Light reflectance – 81 - 85 % • Strength - Antisag • Colour : Pre-painted with approved colour.

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm tapered edge Gypboard (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, window, ventilators etc, cut out made with frame of perimeter channel supported suitably to be measured and paid separately where necessary). (ii) 12.5mm thick

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 800 x 800 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red. Area of slab over 0.50 sqm

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) Note: For uPVC frame and sash extruded profiles minus 5% tolerance

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Float glass panes , 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Brick work with common burnt clay machine moulded perforated brick of class designation 12.5 conforming to IS2222 In superstructure above plinth level to floor five level in cement mortat 1:6 (1:cement:6course of sand) With F.P.S (non modular bricks)

Providing and applying polymer modified, flexible cementatious negative side water proofing coating with elastic waterproofing polymer on interior wall plaster surface in three coats @14.35kg/10sqm one coat of self priming of cementatious water proofing polymer (dilution with water in the ratio 1:1) and two coats of cementatetious water proofing polymer (dilution with water in the ratio 3:1) after scrapping and properly cleaning the surface to remove the pre-existing paint flim and loose particles till plaster is visible, complete in all respect as per direction of the engineer in charge.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :: Two or more coats on new work

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in-charge.

Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (In cement mortar)

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm

Dismantling doors, windows and clerestory windows (steel or wood)shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood)shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres leadOf area beyond 3 sq. metres

Taking out doors, windows and clerestory window shutters (steel orwood) including stacking within 50 metres lead :Of area beyond 3 sq. Metres

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable materialand stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge

Disposal of building rubbish/malba/similar unserviceable, dismentaled or waste material by mechanical transport including loading, transporting and unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per direction of engineer in charge.

Glass film /Glass paper : Supplying and installation of good quality commercial Glass film/ Glass paper from brand having good market track record over last five years, of approved colour, pattern and design (where applicable) and fixed with proper adhesive. The joints of Glass film/ Glass paper should not be visible in any case. Complete and finished in all respect and as per the directions of Engineer in-charge. (Minimum MRP of the product should not be less than Rs. 1000.00 per Sqm) only

Supplying & Installation of Workstations cubicals along with partitions. Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Partition: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top.Fabric magnetic and glass markers are provided for each workstation. Modesty Panel: 18mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. 1 Under Structure Support: 18mm thick PLT gable end. Wire Management: Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access. MOBILE PEDESTAL 2D1F SIZE: 400W X 450D X 600HT Specification: Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle and suitable locks. CPU and Keyboard Tray without Mousepad Cost of electrical switch sockets front plate wires and electrician charges are included in the quote.Cubicle: 1500W X 750D X 750HT Table top and 1200 Ht partition, includes additional extended partitions as per the layout.

Supplying & Installation of Workstations cubicals along with partitions. Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Partition: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top.Fabric magnetic and glass markers are provided for each workstation. Modesty Panel: 18mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. 1 Under Structure Support: 18mm thick PLT gable end. Wire Management: Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access. MOBILE PEDESTAL 2D1F SIZE: 400W X 450D X 600HT Specification: Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle and suitable locks. CPU and Keyboard Tray without Mousepad Cost of electrical switch sockets front plate wires and electrician charges are included in the quote. Size: 1500W X 600D X 750 HT table top and 1200HT Partition with 350mm HT intermediate 12mm fabric magnetic screens on studs

Supplying & Installation of Workstations cubicals along with partitions. Specifications: Table top: Made of 25mm thick prelaminated particle board of approved shade. All the edges of workstation surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. Partition: Height - 1200mm frame with top and sides in Aluminium trims and junctions with diecast caps. Partition is made of 50mm thick 1200mm ht NEO based system with fabric above and lamiante below the table top.Fabric magnetic and glass markers are provided for each workstation. Modesty Panel: 18mm thick 450mm ht plt modesty panel is considered.Wich is machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. 1 Under Structure Support: 18mm thick PLT gable end. Wire Management: Raceways are provided BTT only main spine and skirting on main (inside) spine for power and data cable management. 65mm dia grommet hole is provided for wire access. MOBILE PEDESTAL 2D1F SIZE: 400W X 450D X 600HT Specification: Pedestal are made of 18mm thick prelaminated particle board of approved shade. All the edges of pedeatal surface shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. With 2 drawer units and 1 filling folder unit. The drawer units are provided with finger groove handle and suitable locks. CPU and Keyboard Tray without Mousepad Cost of electrical switch sockets front plate wires and electrician charges are included in the quote.Size: 1500W X 600D X 750 HT table top and 1200HT Partition with 350mm HT intermediate 12mm fabric magnetic screens on studs

Supply & Installation of storage units. The storage top 25/18mm thick, shutter & sides panel are made of 18mm thick & back panle is made of 09mm thick prelaminated particle board of approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping glued with hotmelt Eva glue free from any VOC.with finger groove handle & suitable lock.All exposed area PVC edge lipping. size: 750W X 450D X 1200HT

Supply & Installation of storage units. The storage top 25/18mm thick, shutter & sides panel are made of 18mm thick & back panle is made of 09mm thick prelaminated particle board of approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping glued with hotmelt Eva glue free from any VOC.with finger groove handle & suitable lock.All exposed area PVC edge lipping. size: 900W X 450D X 1200HT

Supply & Installation of storage units. The storage top 25/18mm thick, shutter & sides panel are made of 18mm thick & back panle is made of 09mm thick prelaminated particle board of approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping glued with hotmelt Eva glue free from any VOC.with finger groove handle & suitable lock.All exposed area PVC edge lipping. size: 900W X 450D X 750HT

Supply and installation of High mesh back chair with head rest, single lock synchro mechanism, adjustable arms, adjustable lambar support, nylon base. Model: Versa HB or equivelent

Supply and installation of High mesh back chair with head rest, single lock synchro mechanism, adjustable arms, adjustable lambar support, nylon base. Model: Versa HB or equivelent

Supply and installation of Size 4800w x 1200d x 750ht Table top 25 mm prelem particle board with 2mm pvc edge lipping. Understructure powder coated 50 x 50 perform legs and 40 x 20 cross beam support.

Supply and applying of 2D wall painting with water based High quality paint on finished wall surface completed with a coat of water based wall primer.

Providing & fixing 6 mm thick solid surface arylic sheet no porous, homogeneous surfacing material composed of about 1/3 acrylic resin and about 2/3 natural mineral comprising of aluminium trihydrate derived from bauxite with computerized numeric controlled router design cutting

Supplying & fixing glass embossed coloured/ black and white signages of various size as per the approved design including necessary arrangement of fitting and fixing of the same. Prior approval of sample is required from the authority before supply of the signage.

Supply of artificial plant including pot, Plant height should be not less than 800 mm, the diameter of the pot should not be less than 300mm, height of the pot should not be less than 450mm.

Supply & installation of Launge table, model: woodrow cafe- solid wood leg or equivalent. Size 800dia x 750 ht

Supply of launge sofa, Model: Clara 4 leg or equivalent, Lounge single seater sofa, powder coated four legs

Providing & fixing vertical blinds on windows including all necessary fixtures required for its installation.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door (For Power , Light & AC)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door (For Power , Light & AC)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing of RCBO Four Pole 415 V 63 Amps 100mA

Supplying and fixing of RCBO Four Pole 415 V 40 Amps 100mA

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supply of 1.1 KV grade XLPE aluminium cable of following rating 4C x 35 sq mm armoured cable.

Supply of 1.1 KV grade XLPE aluminium cable of following rating 4C x 25 sq mm armoured cable.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe/Tray as required. Upto 35 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV gradeas required 4 X 25 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV gradeas required 4 X 35 sq. mm (32mm)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the ame in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the ame in case of recessed conduit as required.25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the ame in case of recessed conduit as required. 32 mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group A

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group B

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group A

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair

Supply and fixing of Telephone outlet (RJ11) Double type as required as directed by EIC

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run

Supply and fixing of Data outlet (RJ45) with anodised GI box with front plate etc. as required all complete as directed by EIC.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A (5 pin) socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/Lamps etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. (Upto 450 mm sweep)

Supply of 36W 2x2 LED Panel light (Philips Model No: RC383B LED 36S-6500 PSU OD WH PIR )equivalent from other approved make as directed by the E-I-C

Supply and Fixing of Flexi strip cove light.(Havells FLEXISTRIP5MIP2024V equivalent from other approved make as directed by the E-I-C)

Supply of Wall fan 400 mm Sweep Havells model Girik Neo 400 mm Sweep equivalent from other approved make as directed by the E-I-C

Supply of ISI marked 300 mm sweep, 230 Volt AC Ring mounted Exhaust Fan including wire guard etc.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Installation, testing and commissioning of metal/GI raceway necessary supporting to distribute Power, Data and Telecom cables including junction box, riser, coupler etc including all accessories. all complete as directed by EIC 100 mm x 38 mm (1 compartment )

Installation, testing and commissioning of pop up box suitable for furniture fittings.8 module

Installation, testing and commissioning of over floor trunking with cover as required

Supply and fixing of Body plus cover trunking suitable for arteor wiring with inclusion of all accessories end cap,internal and external angles,Flat angles. Size:50X105 mm

Installation, testing and commissioning Arteor and Myrius support 2 module

Installation, testing and commissioning of Arteor and Myrius support 6 module

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supply, Installation, Testing and Commissioning of 25A motor starter for AC (2 module)

Cable termination: Common specification for this and same category of items below.termination of armoured power cables typically PVC/XLPE insulated up to 1100 Volt grade. Job includes earthing the cable armour, connecting to the terminals, supply and marking of up to 1100 V 3/3.5/4 Core of size wire no ferrules/cable tag(SS/Aluminum/Lead, strip minimum 2 mm thick and 20 mm wide at the termination point), drilling in equipment, removal, cutting, fixing of gland plate, fixing of cable glands, supply and fixing of PVC shrouds for outdoor termination, cutting and stripping of cable insulation, crimping the lug on the conductor, clamping of the cable cores, consumable items like crimping paste, insulation tape, including supply of cable WP GLAND and LUGS etc. complete, including all labour and materials complete as per approved drawing, specification of this tender and direction of EIC. Up to 40 mm outer dia.

Installation, testing and commissioning of ceiling fan/wall fan including the wiring the down rods of standard length upto 30 cm with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

M/s M.A. Enterprise

Bodan Baruah