Hubballi Division: Provision of workmen sheds in Castlerock, Doodhsagar and at Kulem ghat sections.(Maintenance period-12 months)

Item Breakup - B-SCH-B

Preparation of Site plan, GAD and designing Sqm foundation and other structural design, preparation of detailed structural drawing and submission of design calculation with check print for verification and corrections, carrying out correction as per corrected check print and submission of 4 copies of drawing with negative and floppy etc., as per general arrangement drawing and submission of completion drawing as per the execution in tracing paper/tracing film after completion of work duly incorporating any deviation/changes carried out during execution from original approved drawing without completion drawing final bill will not be finalized

Conducting recognized Government Institution HUBLI DIVISION-ENGG/SOUTH WESTERN RLY

Fabrication, Supply and erection of portable Job Cabin using PUP(Polyurethane foam) Body size 8m X 5m X 3.05m H, Including 50mm Thick Wall and roof PUF Panels, Gl Sheets Tubes, Nuts and Bolts, Painting, Welding Sealant for sheet Bunding. Insulation Bed room size 16 feet*9feet, Toilet-2Nos-5*3.5 feet, Kitchen-5*7 feet, Hall 10*16 feet, Passage 6*7 feet. "Components" *Bottom Frame Galvanised Iron C section of size 80mm X 52mm X 2MM Thick. Top Frame C- Section of size 80mm X 52mm X 2mm Thick Side Wall Using PUF sheets of 50mm Thick Verticals. C-Section of size 80mm X 52mm X 2mm Thick. Roofing: Using PUF sheets of 50mm Thick Sretcher: C-Section of size 80mm X 52mm X 2mm Thick Door Im X 2.13m-4No's of Using PUF sheets of 50mm thick with std hardware locks and handle's. Toilet door: 2.5 ft X 1.8 M-1 No's of Using PUF sheets of 50mm thick with std hardware locks and handle's Windows: Im X 1.22m6No's of using double shutter sliding aluminium powder coated windows of 1.3mm thicknesss with 4mm thick glaas with safety grill made of MS rods for all windows and Canopy on the top of windows. Ventilators 211 X 2ft-2 No's Aluminium coated ventilators of 1.2mm thickness with 4mm thick glass with safety grill made of MS rods. NOTE-1. Cost includes fabrication at site, labour charges, transportation, loading, unloading and GST ii. Payment to be done after completion of work in all aspects. Required modifications in design and execution are to be made as per the instructions of Engineer-in-charge at no extra cost. iii. GAD of the prefabricated structure and material test reports from NABL accredited laboratories need to be submitted before dispatching the structure to the site and final decision will be taken by Engineer-in-charge. iv. One sample strucure to be made ready in the manufacturing location and only after inspection and written approval by a representative of the Engineer-in-charge, all structures should be dispatched, v. PG will be released after completion of one year maintenance period. And during one year maintenance period no extra payment will be made if any repair works are carried out. vi. There should be less plumbing work with water light structure. Cost excludes civil work up to plinth level and electrical. (Ubit=total Job) HUBLI DIVISION-ENGG/SOUTH WESTERN RLY

Fabrication, Supply and erection of Ms Job Portable security cabin of size 10x8x8° 5° ft. which includes all necessary electrical Fittings 1.Main Door-1 Nos-size 3*7 2. Aluminum power coated sliding windows with safety grill and canopy-2 Nos-size 3'x3' 3 Shelf-1 Nos Electrical Fittings 4 Led tube light -2 Nos 5. Door lights-1 Nos, 6. cabin fan-1- Nos 7. AC point -1 Nos, MCB single cool-2Nos, Power points-6Amps-2Nos, 15Amps-1Nos (2-switches and 2-sockets) "Fabricating Specifications. 1 Bottom Frame Specially formed 140*60 G-channel, 100*50 C-channel & 100*50mm specially formed MS square tubes 2. Stiffener Bottom- 100*50mm, 50*50mm MS square pipes.1. Top Frame-Frame made of 50*50mm, 50*25mm, 25x25mm MS square tubes 4. Stuffener Top-50*50mm, 25x50 mm &25x25 mm square pipes 5 Side Wall Stiffeners- Specially formed 50*50,50*25mm, 2.00mm MS square tubes 6 Paneling Outside- Specially corrugated 1.2mm thick sheet of 18G welded on MS frame's Marked. 7. Internal Wall Paneling The paneling of side walls and roof shall be of 9 mm thick Pre laminated particle board (OR) MDF Board & all vertical and horizonial corners shall be neatly and smoothly finished with Aluminum sections "Roof Outside - 1.2 mm thick Ms slanted roof with specially formed rain gutters of sheet welded on MS structure frame 9. Bottom Flooring-On the bottom frame 18 mm thick Bison panel ie. Cemented bonded fiber sheets shall be fixed by means of self-taping screw &1.5mm thick PVC vinyl Carpet shall be fixed on the panel (100% water, termite & dimensional proof with vinyl Carpet) 10. Aluminum Sliding Windows - Double shutter sliding aluminum powder coated windows of 1.2mm Thickness with 4mm thick glass for all windows &canopy on the top of windows 11. Main Door-The door shall be of external opening type made out of the same material as wall panels& canopy above the door. Frame work by tubular pipe of 25X25& the door interior shall be finished with same material matching with that of the Cabin interior. Door with standard hardware locks & handles 12. Insulation-25mm Glass woo. density of 48 kg/m3 50mm inside roof with insulation for top &25mm foam on side walls. 13. Wiring Wiring shall be donc using PVC conduit & fire resistance wires of ISI quality suitable for 240V single phase AC supply 1.5sqmm & 2.5sqmm thiet cable for light & fan fittings, Samps switches & sockets, 4mm thick cable for main electric supply with MCB 14. Painting-All components are painted with a coat of primer & 2 coats of corrosion free paint externally and internally 15. Hooks Specially formed for easy lift & shift (Unit-Total job) Total 7845729.00

Item Breakup - D-SCH-D

Item Breakup - D2-SCH-D2