Construction of Labour Commissioner Office Complex at Batamaloo Srinagar

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Demolishing cement concrete 1:3:6 or richer mix (i/c equivalent design mix) manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge.

Demolishing cement concrete 1:4:8 or richer mix (i/c equivalent design mix) manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge:In cement mortar . (serviceble material to be handed over to the concerned department)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead Of area beyond 3 sqm.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead.(serviceble material to be handed over to the concerned department)

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of :G.S. Sheet (serviceble material to be handed over to the concerned department)

Carriage of Building Rubbish/Material at an average lead of 5KM by Mechanical Transport including loading, unloading and stacking.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge All kinds of soil :

Extra for every additional lift of 1.5 M or part therefore in all kinds of soil All kinds of soil :

Excavating, supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Carriage of Building Rubbish/Material/ Earth Work at an average lead of 10KM out side Muncipal Limit by Mechanical Transport including loading, unloading and stacking.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed.

Extra for laying concrete in or underwater and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete Note for item No. 4.22:- The quantity wil

l be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under subsoil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m, 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.

Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of specified grade concrete mix, diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embeded in the pile cap etc. all complete including removal of excavated earth with all lifts and leads(Length of pile for payment Shall be measured from top of shoe to the bottom of pile cap) 21.2.1 By percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, (M-30)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including Admixtures in recommended proportions, (as per IS 9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All work upto plinth level.

Extra for laying concrete in or underwater and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete Note for item No. 4.22:- The quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under subsoil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m, 0.05m or more shall be taken as 0.1m and less than 0.05m ignored.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including Admixtures in recommended proportions, (as per IS 9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All work above plinth level upto floor V level.

Extra for providing richer mixes at all floor levels. Note:- Excess/ less cement over the specified cement content used is payable/ recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. (of approved make).

Add or deduct for using more or less cement in the items of design mix over and above the specified cement content there in.

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars. (Thermo-Mechanically Treated bars of grade Fe-500D or more.)

Columns, pillars, piers.

Lintels, beams, plinth beams.

Suspended floors, roofs, landings and access platforms.

Edges of slabs and breaks in floors and walls upto 20cm wide.

Weather shades, chajjas, corbels etc. including edges.

Wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc

Stairs (excluding landings) except spiral stair cases.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and laying DPC 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and curing complete.

Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 (1 cement : 4 fine sand).(Below Plinth upto Plinth level)

Providing and laying autoclaved aerated cement blocks masonry with 230mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately).

Extra for brick work/tile brick/AAC block masonry in superstructure above floor V level for each four floors or part thereof by mechanical means:

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in superstructure above plinth level upto floor V level in cement mortar 1:4 (1 Cement : 4 coarse sand ) and curing complete. The rate includes providing and placing in position 2 nos. 6 mm dia M.S bars at every third course of masonry work.

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:6 (1 cement : 6 fine sand).

Extra for brick work in super structure above plinth level upto floor V-level.

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand).

Extra for half brick work in super structure above plinth level upto floor V-level.

Extra for providing and placing in position 2 Nos 6mm dia M.S Bars at every third course of half brick masonary .

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand).

Making of grove 12mm x 10mm between brick and RCC.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded brick aggregate 40 mm nominal size below flooring, retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing.

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections.

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed.

Brick edging 7 cm wide 11.4cm deep to plinth protection with bricks of class designation 75mm including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

(c)Fire Exit signage at each stair on every floor, indicating the direction of fire exit, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.

Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and

the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm.

Providing and laying Full Body vitrified floor tiles 600x600 mm (in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete job

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying 18mm thick Granite of any colour and shape (area of slab over 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in groundin Existing DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required. 3.5 C X 300 Sq.mm A2XFY

Extra for providing edge moulding to 16 mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Wooden planking, tongued and grooved in flooring including fixing with iron screws complete: 12 mm thick Second class teak wood.

Providing and fixing Ist quality ceramic glazed wall tiles(300X600) conforming to IS : 15622(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing of Fabric Acoustical Wall Paneling with square edges made of Rockwool with Glasswool Tissue substrate 25mm thick and wrapped on the front side with an acoustically transparent and fire-resistant fabric with an option of colors as per the choice of the Architect/ Engineering- in charge of size 600x1200 or 600x600 mm, 300X300 mm or adjust as per site providing a minimum sound absorption level of 0.90 NRC. The GI stud system includes G.I Stud having Size 48 mm X 36 mm X 34 mm X 0.50mm, length 3600mm, and Floor Channel Size 50 mm X 32 mm X 32 mm X 0.50 mm, length 3600 mm is fastened vertically/ horizontally at every 600mm filled with 50mm 1000GSM non-woven thermal bonded polyester wadding. Then 8 mm HDMR perforated Board of Gyptech Make should be Screwed to the GI frame with the help of 25 X 6 mm metal screw 25mm thick fabric acoustical panel should be pasted on the 8 mm HDMR perforated Board with the help of rubber base Adhesive of Pidilite or equivalent make as per drawing and design of Engineer-in-Charge. Make: Gyptech / Armstrong / Anutone.

Providing and fixing of charcoal wall panelsrectangular in shape made of charcoal and polystyrene proportionately 12mm thick and fire-resistant, waterproof, termite proof, weather resistance, durable material, anti static, and premium quality with an option of colors as per the choice of the Architect/ Engineering- in charge of size 300x2850 or 270x600 mm providing a minimum sound absorption level of 0.90 NRC. Then 8 mm HDMR perforated Board of Gyptech Make should be Screwed to the GI frame with the help of 25 X 6 mm metal screw 25mm thick fabric acoustical panel should be pasted on the 8 mm HDMR perforated Board with the help of rubber base Adhesive of Pidilite or equivalent make as per drawing and design of Engineer-in-Charge.

Providing and fixing of 9.5 mm thick GRC wall Cladding (Tiles) of pattern BRICK castle (size 4” x 10”) on exterior wall / surface. Including scafolding Unistone make as per the approved sample. All complete as per architectural drawings and the directions of Engineer-in-Charge.

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc with all necessary Acessories and fittings complete job. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. a. Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm &mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqmu pto 5.00 sqm).

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.or wherever required as per the direction of Engineer Incharge. (of approved make).

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinderwith keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all

corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water et cwith all necessary Acessories and fittings complete job. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. a. Casement door with 3D hinges made of (big series) frame 67 x 64mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing of glass panes weighing 12.50 kg/sqm (5.0mm thick)

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured)

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coated 50 microns).

Providing and fixing of Epoxy (Baby) insulators with its all accessories like fabricated steel cliffs of adequate sizes and nuts & bolts complete for resting/fixing of G.I earth upto lighting arrestor

Providing and fixing of Al.Solder Less Clamps for HT Transformer duly fitted with necessary nuts & bolts.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm).

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand andmanufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge with brass cover plate.

Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms. (of approved make).

Filling the gap in between aluminum frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper.

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter.

Single tee with door 110 x 110 x 110mm.

Bend 87.5* 110mm.

P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc. (HILTI :- NUTS & BOLTS (HST-4))

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacture,over the plasterted wall surface to prepare the surface even and smooth complete

Finishing wall with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm) having Algal & fungal Resisitance.

Finishing walls with textured exterior paint (Rustic Regular)of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Providing and fixing Fabric vertical /roller blinds as per Design and concept as per direction of Consultant approval .

Providing and fixing Plane floor trap with heavy class SS grating and setting in floor with cement mortar to match the floor finish as per direction of Engineer-in-charge (size 100 X 75mm mm dia) ISI marked. (of approved make).

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of 275 gram/m2 .the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

FLASHINGS/ APRONS (UPTO 600MM)

GUTTER (600MM OVER ALL GIRTH)

Supply and Making end Termination with Brass Compression Gland and Aluminium Lugs for the Following Sizes of PVC insulated and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Comet) 3½ X 300 sq. mm (70mm)

BARGE BOARD (UPTO 600MM)

PLUMBING Providing & fixing of white vitreous China wall hung concele type water tank (European Type) with cistern with Push Back, CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge. (of approved make)

Providing and fixing 2nd class Deodar wood plained eaves boarding.250x32 mm (nominal size)

Providing flat iron brackets 50 x 3 mm size with necessary bolts, nuts and washers etc. for fixing asbestos cement/ G.S. sheets gutters with purlins.

Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to t

he main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with GI Metal Ceiling Clip in plain Beveled edge global white colour tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and fixing of glass panes weighing 12.50 kg/sqm (8.0mm thick) with all Necessary fittings & Acessories complete Job. As per Engineer in Charge.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items(galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with:8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) : Second class teak wood.

Providing and fixing specified board medium density exterior grade (Grade I) to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately) : Flat pressed 3 layer particle board or graded wood particle board IS:3087 (18MM).

Providing and fixing 2nd class teak wood lipping/moulded beading or Taj beading of size 18x5mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the pre laminated particle board as per directions of the engineer-in-charge.

Providing and fixing ply wood 4mm thick one s

ide decorative veneer conforming to IS: 1328(type 1), for plain lining/cladding with necessary screws, including priming coat on unexposed surface with. Decorative veneer facings of approved manufactures.

Melamine polishing on wood work (one or more coats).

Providing and fixing of glass panes weighing 12.50 kg/sqm (5.0mm thick) with deodar wood fillets.

Providing & Fixing of p.v.c sheet signages &bond in front of every Accomodation / Room fix with s.s. screw.

Providing & Fixing of stainless steel 3d letter in (304 grade ) including fixing with all necessary fitting and Scaffolding size as /the direction of Consultant .

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-incharge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing & fixing commercial 20 LPH water purifier of required capacity 8 LTR. Including all components as per manufacture specifications, including connection from water supply line, and final connection to water cooler electric wiring & plug top etc. with all accessories. (of approved make)

Providing and fixing water closet squatting pan (Indian type W.C. pan) , including flush pipe (of approved make) with manually controlle

d device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 18.1.2 White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.(of approved make).

Supply & fixing of Anticlimbing Devices for HT /LT Poles.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 18.11.1 Kitchen sink with drain board 18.11.1.1 510x1040mm bowl depth 250mm (of approved make).

Providing and fixing, testing and commissioning of C.P brass Sink mixer with regular swinging spout (wall mounted model) with connecting legs and wall flanges complete as required and making good as per direction of Engineer-in-charge (of approved make).

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931. (of approved make).

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (of approved make).

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 19.16.2 150 mm diameter (of approved make).

Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931. (of approved make).

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.(of approved make).

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: 18.28.1 Semi rigid pipe 18.28.1.1 40 mm dia (of approved make).

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: 18.69.2 Waste coupling 38mm of 83 mm length and 77 mm breadth weighing not less than 60gms. (of approved make).

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. (of approved make).

Spreading of sludge, dump manure or/and good earth in required thickness as per directions of officer in-charge (cost of sludge, dump manure or/and good earth to be paid separately)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300mm (W) x 50 mm (H) wide cable tray perforated type

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern , including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:18.2.1 W.C. pan with ISI marked white solid plastic seat and lid. (of approved make).

Providing and fixing complete set of sanitary fixtures for handicapped toilets, comprising of EWC 710X370X770MM, , Cistern, Seat Cover, Twin Flush Fittings, Wash Basin 665X545X190MM, l, 1 faucet with spatula lever, 1 hinged rail and 1 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge. (of approved make)

Fine dressing of the ground

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.

Supply ,Installation ,Testing and comissioning of Pole Top mounted 2 Way Pole bracket fabricated out of 42-50 mm dia , 3.2 mm thick Mild Steel pipe of 0.75 Mtrs length on either sides from pole top as per IS 2062/IS 1239 having hot dip galvanization of as per IS 2629/IS 4759 suitable for for suitable for holding of 150 Watts LED fixture(Excluding cost of fixture) of same make as of pole (Sample to be approved by department not less than the rank of SDO)

Supply ,Installation ,Testing and comissioning of Pole Top mounted Single Way Pole bracket fabricated out of 42-50 mm dia , 3.2 mm thick Mild Steel pipe of 0.75 Mtrs length from pole top as per IS 2062/IS 1239 having hot dip galvanization of as per IS 2629/IS 4759 suitable for for suitable for holding of 150 Watts LED fixture(Excluding cost of fixture) of same make as of pole (Sample to be approved by department not less than the rank of SDO /DO)

Supply, assembling ,Installation, Testing and Commissioning of 150W LED Street lights (IP66) having minimum 140 lm/W , high power LED,S with lens plate, LM6 PDC housing , high efficiency glass cover, cool white, IP66 protected, with system power of Philips /Regent /Endo /Trulux /Wipro make (Sample to be approved by department not less than the rank of SDO) Approved make Philips / Lighting techology / Trilux /wipro/ Endo / Igguzini /Regent make The Agency / firm must submit the Techanical data sheet (TDS) on OEM Letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO /DO ,prior to the supply of materials

Supply ,Installation ,Testing and comissioning of Pole Top mounted 2 Way Pole bracket fabricated out of 42-50 mm dia , 3.2 mm thick Mild Steel pipe of 0.75 Mtrs length on either sides from pole top as per IS 2062/IS 1239 having hot dip galvanization of as per IS 2629/IS 4759 suitable for for suitable for holding of 150 Watts LED fixture(Excluding cost of fixture) of same make as of pole (Sample to be approved by department not less than the rank of SDO)

Supply ,Installation ,Testing and comissioning of Pole Top mounted Single Way Pole bracket fabricated out of 42-50 mm dia , 3.2 mm thick Mild Steel pipe of 0.75 Mtrs length from pole top as per IS 2062/IS 1239 having hot dip galvanization of as per IS 2629/IS 4759 suitable for for suitable for holding of 150 Watts LED fixture(Excluding cost of fixture) of same make as of pole (Sample to be approved by department not less than the rank of SDO /DO)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. (of approved make).

Providing & fixing of white vitreous china counter top oval wash basin/circular basin with CP brass waste assembly, CP cast brass bottle trap with extension piece 450mm long CP copper connections pipes , wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge. (of approved make).

Providing and fixing of C.P. brass Central Hole Basin Mixer/ Table top Mixer without Popup Waste System including with 450mm Long Copper Pipes & Brass Nuts with all fittings and accessories as per direction of Engineer-Incharge. (of approved make).

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points or wherever required as per the direction of Engineer Incharge of approved make conforming to IS : 8931. (of approved make).

Providing & fixing C.P. hand spray with lever control (health faucet) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge. (of approved make).

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality, make and colour, weighing not less than 300 gms.

10 sq mm 2 Core

Centering and shuttering including strutting, propping etc. and removal of form work for :- (a). Foundations, footings, bases of columns.

Mixing earth and sludge or manure in proportion specified or directed by officer in charge.

DISMATLING Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.(serviceble material to be handed over to the concerned department)

Providing of Chemical eating with G I to G I of 2 mts in length and 50 mm in Dia G I Pipe placed vertically in ground by boring 100 mm dia bore with hand drill and filling with 2 bags of chemical complete. The Earthing is connected with 25 mm width G I strip for Earth electrode to feeder Pilar.

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and panelling to be paid for separately). 12 GUAGE (a). For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).

Providing and fixing white vitreous china flat back type lipped front urinal basin of 430x260x350 mm and 340x410x265mm sizes respectively.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. (MAKE:- Kerovit, Essel, CERA Hindware)

earthing of poles with GI rod of 6 ft long to be embedded in a pit with extending of earthing from rod to pole by way of p/l of 25 mm flat iron strip

Providing and fixing16mm/18mm stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and finished smooth. White Agaria Marble Stone

Wiring for Circuits / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface l recessed medium class PVC conduit as required. of Polycab / Finolex /Anchor / Salzer /RR Cables make.(25 mm dia PVC Unbreakable conduits upto 6 sq.mm and 32/38 mm dia conduits above 6 sq.mm wires of Anchor /Finolex /Ravinder /Paraflex make including cutting of walls and refacing of walls to original position with cement concrete ,pop and painting of cutting portion inorder match to existing walls complete Job including conduits and allied accessories ) 2 X 1.5 sq. mm +1 X1.5 sq. mm earth wire

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

32 mm dia. nominal bore (Medium)

40mm dia. nominal bore (Medium)

32 mm dia. nominal bore

40mm dia. nominal bore

Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed.

110MM dia

Supplying, fixing, testing and commissioning of Dismantling Joint of PN 1.6 rating of Ductile Iron ISI marked complete with nuts, bolts, washers, gaskets of following sizes as required : 150 mm dia

150MM dia

Supply, installation, testing and commissioning of Rubber Expansion Joint, Rubber Bellows (Flexible coupling) with required flanges,nuts,bolts & accessories 150 mm

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :- (a). Coupler 110mm.

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

150 mm dia

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design Inside dimensions 455x610 mm and 45 cm deep for single pipe line-

ELECTRICAL Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable of Polycab / Finolex /Anchor / Salzer /RR Cables make to be laid in surface / recessed medium class PVC conduit (25 mm dia PVC Unbreakable conduits of Anchor /Finolex /Ravinder /Paraflex make including cutting of walls and refacing of walls to original position with cement concrete ,pop and painting of cutting portion inorder match to existing walls complete Job including conduits and allied accessories ), with 6 Amps modular switch, modular plate of Anti backteria series ( Anti bacteria series of ABB /L&T /Legrand /Simens make , ) , suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(P+N+E is to be provided sperately for normal and invertor points ) .The Job further includes providing and fixing of concealed Lighting deep /fan deep (heavy duty sheet steel) as per site requirement as per instructions of Engineer Incharge.

Supply and errection of 7 mtrs hot dip galvanized octagonal poles Utrakash India Ltd. /Crompton Greaves /Philips /KEI / Mayfair Lighting &poles /Bajaj make, fabricated out of High Tensile steel (Grade S355 or Equivalent as per BS EN 10025 /IS 2026 & pole shall be in single section, having Top dia 90 mm and bottom dia 150 mm with thickness of minimum 3 mm having galvanizing thicness of 70 Microns twin hot dip galvanization suitable for climatic and seimic conditions as laid in relevent IS-specification ammended up to date .The pole shall be desined wind speed of 180-250 KM/h (as per IS 875 Part-3) . The pole should have base-plate made up of galvanized steel conforming to IS-2062 with the dimen

Supplying and fixing orifice plate made out of 6 mm thick Stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

sions 260 X 260X 16mm ...The pole should have door opening reinforced and weather protected with all accessories plate mounting strips 20x4 mm . The length of the door opening should be 500 mm and should be 1200 mm above the concrete level... The pole will have arrangement inside for fixing of the cable termination connector complete job. 2 No. SP MCB Of required amperage with detachable covers. Required length of PVC Copper wire multistrand 1 sq mm. 1 set of foundation bolts of required size and length. Required size of lugs duly crimped and cable termination gland wherever required. 1 No. 4 pole heavy duty termination connector

Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 200x10mm.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125MM

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard designInside dimensions 600x850 mm and 45 cm deep for single pipe line with three or more inlets.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor pile method and preparation of pile head or construction of test cap and dismantling of test cap after test etc complete as per specification & the direction of Engineer-inCharge. 21.6.1 Single pile upto 50 tonne safe capacity 21.6.1.2 Routine test (Test Load 1.5 times the safe capacity)

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked)

Providing and fixing 100 mm sand cast iron grating for gully trap.

(b) 1620 (20mm OD) pipe.

(c) 2025 (25mm OD) pipe.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : (a). RIDGES PLAIN (500-600MM)

Designing, fabricating, testing, protection, installing and fixing inposition semi (grid) unitized system of structural glazing (with openjoints) for linear as well as curvilinear portions of the building for allheights and all levels, including:(a) Structural analysis & design and preparation of shop drawings for thespecified design loads conforming to IS 875 part III (the system mustpassed the proof test at 1.5 times design wind pressure without anyfailure), including functional design of the aluminum sections for fixingglazing panels of various thicknesses, aluminium cleats, sleeves andsplice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc.,structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness,pressure equalization &drainage and protection against fire hazardincluding:(b) Fabricating and supplying serrated M.S. hot dip galvanized /Aluminium alloy of 6005 T5 brackets of required sizes, sections andprofiles etc. to accommodate 3 Dimensional movement for achievingperfect verticality and fixing structural glazing system rigidly to theRCC/ masonry/structural steel framework of building structure usingstainless steel anchor fasteners/ bolts, nylon separator to preventbimetallic contacts with nuts and washers etc. of stainless steel grade316, of the required capacity and in required numbers.(c) Providing and filling, two part pump filled, structural silicone sealantand one part weather silicone sealant compatible with the structuralsilicone sealant of required bite size in a clean and controlled factory /work shop environment, including double sided spacer tape, settingblocks and backer rod, all of approved grade, brand and manufacture, asper the approved sealant design, within and all around the perimeter forholding glass.(d) Providing and fixing in position flashings of solid aluminium sheet1mm thick and of sizes, shapes and profiles, as required as per the siteconditions, to seal the gap between the building structure and all itsinterfaces with curtain glazing to make it watertight.(e) Making provision for drainage of moisture/ water that enters thecurtain glazing system to make it watertight, by incorporating principlesof pressure equalization, providing suitable gutter profiles at bottom (ifrequired), making necessary holes of required sizes and of requirednumbers etc. complete. This item includes cost of all inputs of designing,labour for fabricating and installation of aluminium grid, installation ofglazed units, T&P, scaffolding and other incidental charges includingwastages etc., enabling temporary structures and services, cranes orcradles etc. as described above and as specified. The item includes thecost of getting all the structural and functional design including shopdrawings checked by a structural designer, dully approved by Engineerin-charge. Theitem also includes the cost of all mock ups at site, cost o All samples of the individual components for testing in an approvedlaboratory, field tests on the assembled working structural glazing asspecified, cleaning and protection till the handing over of the building foroccupation. In the end, the Contractor shall provide a water tightstructural glazing having all the performance characteristics etc. allcomplete as required, as per the Architectural drawings, as per itemdescription, as specified, as per the approved shop drawings and asdirected by the Enginee

r- in-Charge.Note: - 1. The cost of providing extruded aluminium frames, shadowboxes, extruded aluminium section capping for fixing in the grooves ofthe curtain glazing and vermin proof stainless steel wire mesh shall bepaid for separately under relevant items under this subhead. However,for the purpose of payment, only the actual area of structural glazing(including width of grooves) on the external face shall be measured insqm. up to two decimal places.Note:-2. The following performance test are to be conducted onstructural glazing system if area of structural glazing exceeds 2500 Sqmfrom the certified laboratories accredited by NABL (NationalAccreditation Board for Testing and Calibration Laboratories),Department of Science & Technologies, India. Cost of testing is payableseparately. The NIT approving authority will decide the necessity oftesting on the basis of cost of the work, cost of the test and importance ofthe work. Performance Testing of Structural glazing system Tests to beconducted in the NABL accredited lab or by any other accreditationbody which operates in accordance with ISO /IEC 17011 and accreditslabs as per ISO/ IEC 17025.1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa)& (+50pa to +300pa) as per ASTM E-283-04 testing method for a rangeof testing limit 1 to 200 mVhr2. Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09testing method for a range up to 2000 ml.3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01-05 testing method for a range upto 2000 ml4. Structural Performance Deflection and deformation by static airpressure test (1.5 times design wind pressure without any failure) as perASTME-330-10 testing method for a range upto 50 mm5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testingmethod for Qualitative test, Tests to be conducted on site.6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa(35psi) upto 2000 ml

Carriage of material by Mechanical Transport including loading / unloading and stacking at site complete. (a). Sand for an average lead of 15 Kms.

80 mm dia

Providing and fixing heavy class SS grating plane including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked)

(b). Stone aggregate size for an average lead of 15 Kms.

100 mm dia

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks.

50 mm dia

(c)Bricks for an average lead of 25 Kms

80mm dia

150mm dia

Providing, storing, handling, shifting, installation, testing & commissioning of vertical / horizontal storage type hot water heater fixed to wall with anchor bolts & nuts, 20mm CP brass cock and 20mm non return valve complete including making connection with 15 mm dia CP connecting pipe on Inlet and Outlet, suitable length of power cable and 15A plough (for pantry & Toilets). (Make : of approved make) (a). Capacity 10 liters

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks.

50 mm dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supply, installation, testing & commissioning of Gun Metal Fire brigade suction hose coupling (Draw-out Connection) with nut for female coupling as per IS:902-1974 complete with 100 mm dia. GI suction pipe and 100 mm dia. 1 No. CI foot valve flanged (to be connected to static water tank).

200 mm dia

Internal work concealed with clamps at 1.00 meter spacing including cutting the chases and making good the wall etc., (a) 1216 (16mm OD) pipe.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank(5000 Ltrs), ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

metre

Providing and fixing Weather proof hose cabinets for internal & yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe and one fireman's axe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).

(b). Capacity 25 liters

65 mm Dia

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

150 mm Dia

Providing and fixing Polyethylene- Aluminum- Polyethylene (PE-AL-PE) Composite Pressure Pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80ºC, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. Elbows, tees, reducers, couplers and connectors etc.This includes testing of joints complete as per direction of the Engineer-in-charge: Internal work-exposed on wall with clamps at 1.00 meter spacing (a) 1216 (16mm OD) pipe.

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. Including with all Necessary fittings & Acessories Complete job. INTERNAL WORK-Exposed on wall (a). 25 mm dia. nominal bore (Medium)

(b). 32 mm dia. nominal bore (Medium)

(c)40 mm dia. nominal bore (Medium)

3.5 C X 95 Sq.mm A2XFY

3.5 C X 25 Sq.mm A2XFY

12 C X 2.5 Sq.mm Copper Armoured

3 C X 2.5 Sq.mm Copper Armoured

4 C X 2.5 Sq.mm Copper Armoured

Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etcIncluding with all Necessary fittings & Acessories Complete job. (External work) 40 mm dia. nominal bore (Medium)

3½ X 95 sq. mm (45mm)

3½ X 25 sq. mm (28mm)

12 C X 2.5 Sq.mm Copper Armoured

3 C X 2.5 Sq.mm Copper Armoured

4 C X 2.5 Sq.mm Copper Armoured

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete copatable to connection with composite pipe (a). 25 mm nominal bore

225mm (W) x 50 mm (H) wide cable tray perforated type

100mm (W) x 50 mm (H) wide cable tray perforated type

32 mm dia

125 mm dia

Providing and fixing MS cabinet (to enclose above Draw-out/Fire brigade inlet connections) fabricated from 16g sheet with full front glass door and locking arrangement duly painted with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade and suitably mounted on a raised masonry platform as required (Approx.0.6 m x 0.6 m x 0.45 m).

Supply, installation, testing and commissioning of 1 cu m/hr Open Well Type Submersible Pump including the cost of Electrical Panel with Following Specifications:- Flow Rate:- 1.2 cu .m/hr,Head 20 mtr,Motor Body:-SS,Casing:- cast iron

(b). 32 mm dia. Nominal bore

Providing, installation, testing and commissioning of Pressure Guages

Providing and Fixing of Electromagnetic Type 150 mm D

(c)40 mm dia. Nominal bore

100 mm dia

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks.

50 mm dia

ia Flow meter made out of SS 304 Material with pressure withstand capacity of 25 Kg/Sq.cm with Flange End Connection for the test run pipe.

Supplying,Installation,Testing and Commissioning of CO2 Type Fire Extinguisher 4.5 Kg. Capacity ISI Mark(IS:15683)suitable for 'B' and 'C' class fires - inflammable liquids, gaseous fires like L.P.G. and acetylene, and electrical fires

100 mm Dia

Supply,Installation,Testing & Commissioning of 11 kv Gang operating Switch with Handle and complete hardware (Heavy Type ) complete with nuts & bolts and handle

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work. (a). 25 mm dia. nominal bore (Medium)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing of 1 No. of Shovel and 1 No. of Beater and Mild Steel Fire Sand Bucket, Capacity 5 Kg thickness not less than 6 mm painted in Red with "FIRE" written in Black Paint (Refer IS : 2546-1974) mounted on MS painted structure to carry / hold 4 fire buckets made out of Angle 40mm x 40 mm 5 mm .

Supplying,Installation,Testing and Commissioning of MAP 90 ABC Type Fire Extinguisher 4.0 Kg. Capacity ISI Mark(IS:15683)suitable for Class A/B/C Type Fires .

Wiring for lightl power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable of Polycab / Finolex /Anchor / Salzer /RR Cables in surfacel recessed medium class PVC conduit (25 mm dia PVC Unbreakable conduits of Anchor /Finolex /Ravinder /Paraflex make including cutting of walls and refacing of walls to original position with cement concrete ,pop and painting of cutting portion inorder match to existing walls complete Job including conduits and allied accessories ) alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. Complete job

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

2 X4 sq. mm + 1 X4 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

2 X 6 sq. mm + 1 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

4 X 10 sq. mm + 2 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

4 X 16 sq. mm + 2 X 6 sq. mm earth wire with p/f of Copper thimbles of required size and numbers to be fixed on i/p and op sides dully crimped with termination and rolling of colour coded tape

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. ( Anti bacteria series of ABB /L&T /Legrand /Simens make , )

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing of 2 No's of 3 pin 5/6 A modular socket outlet and 2 No's of 5/6 A modular switch, connections etc. as required.( Anti bacteria series of ABB /L&T /Legrand /Simens make , )

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.( Anti bacteria series of ABB /L&T /Legrand /Simens make , )

Supplying & fixing suitable size Gl box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supply and laying of 25 mm dia medium class PVC medium grade Conduit to berecessed on walls / floor complete with all allied accrues like bends, tees etc. for paving way of laying of wires of haeting points /circuits ,machine points /circuits and sub mains .The Job includes cutting of walls / floors with required hydraulic cutter and refacing of walls with cement plaster of required ratio or with P.O.P after laying of conduits refacing to its original position by way of supply and applying of painting of required colour to effected area's.Anchor/Polycab/Finolex/TMT Plus / Paraplex make. for LAN /Fire detection etc except)

Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC)Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factornot less than 0.9, Service Value (CM/M/\N) minimum 6.00,Air deliveryminimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speedcontrol and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75 degree C (ma><.), insulation resistancemore than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. of Usha /Crompton /Havels /Orient /Helonix make

Supply and fixing of extra 25 mm GI rod heavy guage having length upto 76 CM with powder coated paint ,including cost of dash fastners complete job

Supply, Installation testing and commissioning of 200-250 mm sweep Exhaust Fans of Usha / Crompton / Havel's incl making of necessary connections and making of necessary space in walls / Windows as per site.The Job includes providing and fixing of shutter of suitable size hylum sheet for fixing of exhaust fan of Usha /Crompton /Havels /Orient /Helonix make

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 40 mm dia. nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work). 25 mm dia. nominal bore

Supply and fixing of 18 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. Luminaire shall be designed to emit initial system lumen output of greater than 2500 lumens with minimum system efficacy of 140 lumen/watt .The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL

accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver .Approved makes Signify (Philips)/ Igguzini / Lighting Techonology / Endo / Regent /Trilux /Wipro make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 3-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reasons

Supply ,installation ,Testing and Commissioning of 20-22 Watts ,4 ft long LED tube light fitting having aluminium body of standard make dully isi marked ,incl ceiling rose and 2-core transparent wire for connections complete job.The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit initial system lumen output of 2400 lumens with minimum system efficacy of 120 lumen/watt. The luminaire shall comply to lifetime of 50000Hrs @ L70B50 with design ambient temp 45°C. The electronic driver used shall have a power factor ≥0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, THD≤10%, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I. The luminaire should be of Class B serviceability. The luminaire should be at least IP20 & IK02 rated. . The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. .Approved makes Signify (Philips)/ Igguzini / Lighting Techonology / Endo / Regent /Trilux /Wipro make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 3-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reasons

Supply, Installation, Testing and commissioning of 2 ft x 2 ft 36-40 watt LED surface/recess mounted Down lighter panels of Standard make dully Isi marke incl making of necessary Connections.The luminaire shall be IP20 & IK02 compliant. The luminaire shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K/4000°K, SDCM≤5 & CRI≥80.Luminaire shall be designed to emit initial system lumen output of greater than 5000 lumens with minimum system efficacy of 140 lumen/watt The luminaire driver shall comply to following parameters at 220V to 240V: PF≥0.95 (@full load), THD ≤ 5% (@full load), current ripple≤ 5%, EMI/EMC complaint & in-built surge protection of 4KV. The driver shall mandatorily be housed in metal casing & not plastic casing. The luminaire shall emit minimum initial system lumen output of 3600lumens with system efficacy of minimum 140lm/w. The input voltage range shall be 140V to 270V.The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successfu

l bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79, Type Test report for luminaire, EMI/ EMC compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver .Approved makes Signify (Philips)/ Igguzini / Lighting Techonology / Endo / Regent /Trilux /Wipro make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 3-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reasons

Supply and fixing of 12 Watts LED surface /recess (Commercial type) downlighter having following specficafications .The luminaire should have a colour temperature of 6500°K, CRI≥80 and SDCM≤5. Luminaire shall be designed to emit initial system lumen output of greater than 1600 lumens with minimum system efficacy of 140 lumen/watt .The downlighter shall be back-lit & not side-lit. The driver shall have THD≤10% (@full Load) and PF ≥ 0.95 (@full load). The luminaire housing should made of pressure die-cast aluminium. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The luminary shall have average life of 50000 hrs operating temperature -10 C to + 45 C The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab & BIS certificate for LED Luminaire & Driver .Approved makes Signify (Philips)/ Igguzini / Lighting Techonology / Endo / Regent /Trilux /Wipro make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 3-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reasons

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia

Supply ,installation ,Testing and Commissioning of 10-12 Watts ,2 ft long LED tube light fitting having PVC Body (Commercial type) of standard make dully isi marked ,incl ceiling rose and 2-core transparent wire for connections complete job.The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit initial system lumen output of 1400 lumens with minimum system efficacy of 120 lumen/watt. The luminaire shall comply to lifetime of 50000Hrs @ L70B50 with design ambient temp 45°C. The electronic driver used shall have a power factor ≥0.95 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, THD≤10%, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I. The luminaire should be of Class B serviceability. The luminaire should be at least IP20 & IK02 rated. The minimum dimensions of the batten shall be 44mm X 51mm X 1157mm. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer

must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals: LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. .Approved makes Signify (Philips)/ Igguzini / Lighting Techonology / Endo / Regent /Trilux /Wipro make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 3-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out what so ever reasons

Supply ,Installation ,Testing and Commissioning of IP66 , 50-60 Watt LED Flood light Luminaries having Aluminium body of of standard make dully isi marked ,to be fitted on walls / poles with necessary cliffs /Clamps with nuts and bolts complete job.The system efficacy of the luminaire shall be ≥120lm/w. The LEDs used in the luminaire shall be from either Lumileds, Osram, Nichia, APT Electronics and CREE make, shall have CCT of 5700°K, CR≥70, SDCM≤5, Life of 50000Hrs @ L70B50. The luminaire shall have IP rating of IP66 & IK rating of IK07. The luminaire shall have lens made of polycarbonate & optical cover made of toughened glass. The LED driver shall have operating voltage range of 140V to 270V, PF≥0.95 @ full load, THD≤ 10% @ full load, In-built surge protection of 4KV, HV Cut off @ 325V (±15V). The luminaire shall have 10KV SPD in-built inside the luminaire. The maximum dimensions of the luminaire shall be, L: 264M, Depth: 52MM & height without cradle: 203MM. The nominal weight of the luminaire shall be maximum 2.4KGs. The luminaire driver & it’s SPD shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79, Type test as per IS10322, FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material for approval. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, BIS certificate for LED Luminaire & Driver. Approved make Philips / Lighting techology / Trilux /wipro "

Supply installation testing and commissioning of IP65 led Bulk head 10 W +/- 1 W LED Surface Pressure Die Cast Aluminum system lumen efficacy of 100 lm/W with Polycarbonate Opal Diffuer and P.F.>0.95 ,THD<10% ,CCT 5700K, CRI 80, IK rating IK08. The LED with Useful life of 50000 Hrs at L70. The Input voltage range shall be 150V to 265V. The Fixture should have In-built Surge Protection of 2.5kV Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised lab .

16 way, Double door for Stilt parking floor

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioninq etc. as required of Legrend /L&T /ABB / Schneider (Acti 9 series ) / Simens make

Supplying and fixing of 63 Amps rating DP 240/415 volts (10KA) of Legrend /L&T /ABB /Schneider (Acti 9 series ) / Simens make dully isi marked complete with making of necessary connections.

Supplying and fixing of 63 Amps rating TPN 415 volts (10KA) of Legrend /L&T /ABB /Schneider (Acti 9 series ) / Simens make dully isi marked complete with making of necessary connections.

Supplying and fixing of 40 Amps rating TPN 415 volts (10KA) of Legrend /L&T /ABB /Schneider (Acti 9 series ) / Simens make dully isi marked complete with making of necessary connections.

3 1/2 X 95 sq.mm(45 mm)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore

Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm. 20 mm dia

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

3 1/2 X 50 sq.mm(35 mm)

3 1/2 X 70 sq.mm(38 mm)

4X10 sq.mm(25 mm)

Supply,Laying,Testing & Commissioning of 95 sq.mm 31/ 2- core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq. make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. (a). 1200mm

necessary connections.

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supply,Laying,Testing & Commissioning of 70 sq.mm 31/ 2- core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq. make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : (a). 150 mm dia

Supply,Laying,Testing & Commissioning of 300 Sq.mm ,31/2 core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 150 mm dia

Supply,Laying,Testing & Commissioning of 300 Sq.mm ,31/2 core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections

Providing,

Supply,Laying,Testing & Commissioning of 50 sq.mm 31/ 2- core armoured Al Cable XLPE/ PVC Insulated and Steel sheathed of Havells/ Eq. make, including cost thimbles on input aswell as output sides dully crimped with hydraulic crimping tool incl making of necessary connections.

63 mm dia (OD-63 mm & ID-51 mm nominal)

installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 32 mm dia

Earthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoall coke and salt as required.The job includes providing and fixing of main hole PVC Chamber with its cover complete job

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100mm dia

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel,ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Telephone Socket (RJ11)

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply ,Installation Testing and commissioning of 24 x 10/100/1000BASE-T PoE ports 2 x Gigabit SFP ports 2 x 10G SFP+ ports Layer 2 management and security with Layer 3 capabilities Static Routing and MSTP security features L2+ Static Routingncluding intergration with main network (D link/Juniper/ Brocade)

Supply ,Installation Testing and commissioning of L3 Core Switch 24 x 10/100/1000BASE-T ports, 2 x 10GBASE-T ports, 4 x 10G SFP+ ports (D Link /Juniper / Brocade)

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying,Installation,Testing and Commissioning of CO2 Type Fire Extinguisher 4.5 Kg. Capacity ISI Mark(IS:15683)suitable for 'B' and 'C' class fires - inflammable liquids, gaseous fires like L.P.G. and acetylene, and electrical fires

100 mm Dia

Supplying,Installation,Testing and Commissioning of Ceiling Mounted Automated Modular Fire Suppression System (ABC MAP90 Powder Based ) - 10KG suitable for Class A, B, C and Electrically started fires.

12 U Rack with Width 600 mm & Depth 400 mm + 100 mm

Providing and laying of shock proof Rubber mats of 2mt. x 1 mt. and 12 mm thick in size of standard make dully isi marked

300 mm width X 50 mm depth X 1.6 mm thickness

200 mm width X 50 mm depth X 1.6 mm thickness

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.The Job includes Comphrensive maintenance contrct for a period of three years reckoned from sucessful handing over the site to intending/user department ,the CMC Includes servicing and repairs /replacement of damaged /defective /mul functioning devices during operation complete job.

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.The Job includes Comphrensive maintenance contrct for a period of three years reckoned from sucessful handing over the site to intending/user department ,the CMC Includes servicing and repairs /replacement of damaged /defective /mul functioning devices during operation complete job.

Supplying, installation, testing & commissioning of fault isolator complete with base as required..The Job includes Comphrensive maintenance contrct for a period of three years reckoned from sucessful handing over the site to intending/user department ,the CMC Includes servicing and repairs /replacement of damaged /defective /mul functioning devices during operation complete job.

Supplying, installation, testing & commissioning of addressable manual call point complete as .The Job includes Comphrensive maintenance contrct for a period of three years reckoned from sucessful handing over the site to intending/user department ,the CMC Includes servicing and repairs /replacement of damaged /defective /mul functioning devices during operation complete job.

Supplying,Installation,Testing and Commissioning of 55 Inches Full H.D LED Display Monitor as per the Specifications attached.

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR Fixed Lens Dome Camera, 1/2.7" CMOS or better, 5MP (2880 x 1620) @ 25fps or better, triple stream at various resolution & Frame Rates, Min. Illumination required 0.007 lux (color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 30m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/2-1/100000S,Adavance Video Compression technology such as H.265, H.264 & MJPEG , Fixed Lens 2.8mm, Field of View FoV H:90°, V:50°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Manual, Minimum Edge Intelligence Video Analytics, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2-Way Audio Full Duplex Line IN/Out, 256GB SD card support, Alarm: 1In/1out, PoE (802.3 af) and 12V DC, Max 5W, IP 66/67 & IK10 with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T Compliant, CE, FCC, EN, RoHS & NDAA Section 889 compliant.

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR Fi

xed Lens Bullet Camera, 1/2.7" CMOS or better, 5MP (2880 x 1620) @ 25fps or better, triple stream at various resolution & Frame Rates, Min. Illumination required 0.007 lux (color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 30m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/2-1/100000S,Adavance Video Compression technology such as H.265, H.264 & MJPEG , Fixed Lens 2.8mm, Field of View FoV H:90°, V:50°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Manual, Minimum Edge Intelligence Video Analytics, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, 2-Way Audio Full Duplex Line IN/Out, 256GB SD card support, Alarm: 1In/1out, PoE (802.3 af) and 12V DC, Max 5W, IP 66/67 & IK10 with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T Compliant, CE, FCC, EN, RoHS & NDAA Section 889 compliant.

Supply , Installation , Testing and commissioning of 24 Channel NVR (Network Video Recorder) Embedded Linux based for recording upto 32CH at D1 960fps with 04 nos. SATA HDDs minimum 40TB storage or more (recording requirement all cameras recording at D1, 25fps for 30 days), H.265 HEVC/H.264/MJPEG codec decoding, Front Panel with LEDs Indication for Power & HDDs Status, 3 nos. USB, ONVIF S, Time Sync with NTP, Encrypted Streaming & Control, 2-Way Audio Line & Out, PTZ Operation Pan, Tilt, Zoom, Support, Pre & Post Alarm Recording Support, Recording/Evidence Clip Export to USB, 16 Channel Synchronous Playback, Playback control i.e Play, Pause, Stop, Fast Forward, Backward, Speed Control, Timeline & Zoom; Snapshot, Web Client, Central Monitoring Software, iPhone; iPad; Android based Mobile clients, 02HDMI & 01VGA Output, 04 On Board HDDS each up to 10TB, Alarm Input (06 nos.), Alarm Output (02 nos.), 196 Mbps throughput, NDAA Section 889 Compliant, Operating Temperature –10°C to 55°C, Certification : Certifications: ONVIF compliant, UL/CSA 62368-1, CE (EN 50130-4), FCC Part 15, EN 55032, NDAA & RoHS (EN63000) compliant. Including fixing accessories and cable termination with required connectors/Jack, complete in all respect as per instruction of engineer in-charge.

SITC of 10TB 7200 rpm SATA 6 Gb/s 3.5" Internal Enterprise Hard Drive

Supplying and Laying of 20 Mtr HDMI Optical Fiber Cable AOC 2.0, 4K with Bandwidth 18Gbps

Supplying and Fixing of S.D Card 256 G.B in the Existing Camera

SITC of CAT 6 F/UTP 16 Port Modular fully loaded patch Panel TIA/EIA-568-C.2:2009 EN 50173- 1:2011 Class E, ISO/IEC11801:2010 (Ed 2.2) Class E, FCC Subpart F68.5 UL Listed.

SITC of CAT 6 F/UTP 24 Port Modular fully loaded patch Panel TIA/EIA-568-C.2:2009 EN 50173- 1:2011 Class E, ISO/IEC11801:2010 (Ed 2.2) Class E, FCC Subpart F68.5 UL Listed.

Supply, Installation, Testing and Commissioning of Layer 2, PoE enabled, with PD: minimum 370 Watt (should have minimum 15.4 Watt per Port), fully managed, 1RU, GE Switch to be operated on 200-240VAC, 50 Hz Supply, with perpetual license of OEM,having minimum technical specification: a) 16 x 10/100/1000Base-T Mbps PoE+ enabled host ports (Minimum); b) 4 x 10GE SFP+ port; c) Forwarding performance/stacking bandwidth/ backplane speed (Minimum) of 95.2Mpps; d) Fanless operation with operating temperature up to 50°C; e) DRAM and Flash RAM as per OEM; f) Software support with IPv4 routing (542 routes), multicast routing (IGMP) including necessary software license; g) Minimum switching capacity of 216Gbps; h) Number of VLAN Supported: 64 (Minimum).; i) Total number of MAC Address: 8,000 (Minimum); j) Minimum Security: User privilege management and password protection, DoS attack defense, ARP attack defense, and ICMP attack defense, Binding of the IP address, MAC address, interface, and VLAN, Port isolation, port security, and sticky MAC, MFF, Blackhole MAC address entries, Limit on the number of learned MAC addresses, 802.1x authentication and limit on the number of users on an interface, AAA authentication, RADIUS authentication, HWTACACS authentication, and NAC, SSH v2.0, Hypertext Transfer Protocol Secure (HTTPS), CPU defense, l; l) REGULATORY: RoHS, WEEE, IEC 61000-4-2:2008, CISPR Class, ICES-003 Class A,UL,CSA 22.2,FCC,EN 300 386, CCC, ICES -003, CB. The OEM should have 24x7 TAC support center with India toll free number reflected in official website.

Supply, Installation, Testing and Commissioning of Layer 2, PoE enabled, with PD: minimum 370 Watt (should have minimum 15.4 Watt per Port), fully managed, 1RU, GE Switch to be operated on 200-240VAC, 50 Hz Supply, with perpetual license of OEM,having minimum technical specification: a) 24 x 10/100/1000Base-T Mbps PoE+ enabled host ports (Minimum); b) 4 x 10GE SFP+ port; c) Forwarding performance/stacking bandwidth/ backplane speed (Minimum) of 95.2Mpps; d) Fanless operation with operating temperature up to 50°C; e) DRAM and Flash RAM as per OEM; f) Software support with IPv4 routing (542 routes), multicast routing (IGMP) including necessary software license; g) Minimum switching capacity of 216Gbps; h) Number of VLAN Supported: 64 (Minimum).; i) Total number of MAC Address: 8,000 (Minimum); j) Minimum Security: User privilege management and password protection, DoS attack defense, ARP attack defense, and ICMP attack defense, Binding of the IP address, MAC address, interface, and VLAN, Port isolation, port security, and sticky MAC, MFF, Blackhole MAC address entries, Limit on the number of learned MAC addresses, 802.1x authentication and limit on the number of users on an interface, AAA authentication, RADIUS authentication, HWTACACS authentication, and NAC, SSH v2.0, Hypertext Transfer Protocol Secure (HTTPS), CPU defense, l; l) REGULATORY: RoHS, WEEE, IEC 61000-4-2:2008, CISPR Class, ICES-003 Class A,UL,CSA 22.2,FCC,EN 300 386, CCC, ICES -003, CB. The OEM should have 24x7 TAC support center with India toll free number

reflected in official website.Make: Cisco, Juniper, Extreme/Netgear/Allied Telesis

Supply,Installation,Testing and Commissioning of Media Converter.

Supply and installation of Following Sizes of Puddle Flanges made out of high quality G.I Pipe.The puddle flange to be tested up to 25 bar water pressure and should work excellently on any weather conditions. (For Details Refer the Drawing) 25 mm Dia

Supply & Erection of Termination Box complete as per specification and as desired by EIC.

Supplying and installing of in position the following type of sign boards made out of 3mm thick "Opaque" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyle painted foam board, complete with mirror fasteners. (a). Signage with printed "IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE" of 1.5cm height letters in red with white back ground. The size of the board shall be 25cm x 30 cm and shall be fixed at the height of 2 mts. from finished floor near Manual call points.

Supplying,Installation,Testing of 12 Core Optical Fibre Cable Single Mode.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.l. tube, having single prong at top, with 85 mm dia 6 mm thick G.l. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.l. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.l. strip, 125 mm long, with 4 nos. of G.l. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.l. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supply/ installation/testing and commissioning of UPS Floor Panel ( Wall / floor mounted) compartmentalized , 415 volts TPN MCCB Mian Distribution panels ,fabricated out of sheet steel of 16 gauge dust protected, painted incl earth terminal with all necessary accessories as required for panel with internal wiring of panel .The Panel is to provided and fitted with following adjustable type controlling /Protection switch gear devices

Supply,Installation,Testing & Commissioning of 400 KVA , (11/ 0.433 KV ) Kv) 3-phase outdoor type oil immersed ONAN cooled Transformer complete with all fittings such as oil Conservator with drain plug,Silica gel,Breather,thermometer,tap changer,oil guage lifting lugs,Drain cum sampling value,filter valve with plug,first filling of fresh transformer oil ,weather proof HT Cable /LT cable Box earthing terminals etc complete .( Energy Efficient Level-2 ). of ALBA / Northsons /Northern / Zain Electricals make The transformer should be of standard make dully isi marked and manufacture unit should have CPRI Registration and BIS Certificate upto required capacity level The complete testing of transformer will be carried out at manufacturing site by departmental representatives before assembling of same and contracting firm has to facilate in all aspects the deptt representatives upto manufacturing site for the said job. The job further includes comphrensive maintenance contract (with p/f of spares if needed) of Transformer for a period of two years reckoned from date of sucessful comissioning (As per Annexure ' A'') "

Providing and fixing of DG Output panel front operated cubical panel 2 mm thick pressed sheet steel enclosure powder coated , dust free and vermin proof panel with hinged gasket and lockable arrangement doors of adequate size complete with interconnections. The panel is fitted with bus bars and provided with following accessories. Incomer 400 Amp TPN Panel type Change over Switch of Havells / Eq. make=1 No 630 Amps TPN Aluminium Bus Bar with heat shrinkable sleeves and shall be colour coded = 1 Set Digital Multi function Volt Meter with C T of proper ratio. = 1 set each indicators = 1 Set each Outgoing 250 Amps TPN MCCB with 36 KA Breaking capacity of L&T /ABB /Legrend /Simens make = 2 No's 125 Amps TPN MCCB with 26 KA Breaking capacity of L&T /ABB /Legrend /Simens make = 1 No's The Job includes angle iron stand of required size whose legs are to grouted on cement concrete block including cost of civil materials and its carriage upto site

Providing and fixing of Servo Output panel front operated cubical panel 2 mm thick pressed sheet steel enclosure powder coated , dust free and vermin proof panel with hinged gasket and lockable arrangement doors of adequate size complete with interconnections. The panel is fitted with bus bars and provided with following accessories. Incomer 630 Amp TPN MCCB (50 KA Havells / Eq. make=1 No 630 Amps TPN Aluminium Bus Bar with heat shrinkable sleeves and shall be colour coded = 1 Set Digital Multi function Volt Meter with C T of proper ratio. = 1 set each indicators = 1 Set each Outgoing 400 Amps TPN MCCB with 36 KA Breaking capacity of L&T /ABB /Legrend /Simens make = 2 No's 125 Amps TPN MCCB with 26 KA Breaking capacity of L&T /ABB /Legrend /Simens make = 1 No's The Job includes angle iron stand of required size whose legs are to grouted on cement concrete block including cost of civil materials and its carriage upto site

Supply,Installation,,Testing & Commissioning of 400 Amps 4-Pole Bypass Changeover Switch of Havells make ,with Angle iron stand to be whose legs are grouted on cement concreate block including cost of civil materials

Provision for construction of cement concreate Bed of required Size with CGI roofing for housing ofof Servo voltage stabilizers and f DG Set. (as per approved drawings)

Supply and Errection of 9 mtrs long Steel Tublur poles with base plate and caps duly welded,the pole is planted at 5- feet deep pit to be excavated and refilled with stones/boulders (SP33)

Providing and Laying of cement concrete for pole bottoms laid in 1:2:4 ratio of cement ,sand and 20 mm nominal size of aggregates complete job including its form work and carriage of materials upto laying site.

Providing of G.I Plate earthing with 6-feet long G.I rod embedded underground with insertion of G.I pipe for watering and filling of char coal or Clay & salt in alternate layers also extension of eathing from rod to lighting arrestors , transformer body & Neutral of Transformer with Al. Strip fitted on poles with Epoxy insulators with cliffs of Sub Stations frame.

Supply and applying of one coat of Red oxide paint & two coats of Aluminium Paint Complete job.

Supply,Installation,Testing & Commissioning of H.T trivector Comparising of C.T (required ratio for 400 KVA (33/0.433 kV -X-mer) ,P.T unit and H.T Energy modium meter capable of recording various electrical paramaters like KVA ,Amps,KVAR ,etc The Job includes providing and fixing of H.T ,ABC Cable 50 Sq.mm of required length for input supply to H.T and output supply to Transformer with required no.& Size of thimbles duly crimped with hydraulic crimping tool & making of necessary connections or cable termination Cable of required size as per instructions of engineer concerned.(including cost of foundation as per approved drawing).The contracting firm has to get meter sealed from concerned division of PDD including all testing and inspections and charges for said job are to paid by contractor

Supply & Fixing of Channel Iron Cross Arms of Size /Angle Iron Braces of required size and length duly painted with red oxide and Al. paint fitted with required size of nuts & Bolts

Supply & Fixing of 200 mm dia ,2 mm thick GI Pipes having length of 10 ft long

(b). Floor identification signage ( i.e., GROUND FLOOR …etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.

Supply,Laying , stringing , jumpering , binding , testing & commissioning of 0.05 ACSR ,incl making of all necessary connections

Supply,Installation,Testing & Commissioning of Earthing to poles using 1 inch dia GI Strip from battom upto pole

Supply,Installation,Testing & Commissioning of 11 kv lighting Arrestor heavy type/station type with nuts & bolts

Supply,Installation ,Testing & Commissioning of 11 kv fuse set with allied fittings complete job. complete with nuts & bolts.