SPECIAL REPAIRS TO BLDG NO P 362 DSC LINE AND KOTE P 267 HEAVY VEH GARAGE P 268 LIGHT VEH GARAGE P 272 MT OFFICE AND P 116 IN MT AREA OF MILIT

Amount

Dismantling plain or corrugated steel sheeting,any gauge ,thickness including Nainital or similar pattern roof covering complete all as specified and directed.

S & F for Pre- painted galvaniume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling structural steel work incl door, gate etc complete all as specified and directed.

S & F Joist, channel, angle, or tee sections, grill ,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-410- W(Gde- E-250) quality-B complete all as specified and directed.

M &L two coat of synthetic enamel paint to steel surface over a coat of rex oxid primer exc 10 cm width or girth incl preparation of new surfaces complete all as specified and directed .

M & L for preparation of old painted surfaces of steel & Iron of any description over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) including necessary scaffolding required for painting work & safety measures at any height of bldg all as specified and directed by Engr-in-Charge.

Taking down of cement plaster of any desc including racking out of joints hacking for keys and scrubing down with water etc complete all as specified and directed.

Rendering 15mm thick in two layers, 5mm thick using WPC @3% by weight of cement over 10mm thick on cement concrete block masonry/concrete surfaces in cement mortar 1:4 finished surfaces even and smooth without using extra cement, complete all as specified and directed.

Rendering 15 mm thick on brick surfaces in cement mortar 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of surfaces and applying 2mm thick wall care putty in two layers on walls/concrete over new plaster surfaces internally complete all as specified and directed.

M&L for two coats of oil bound distemper over a coat of primer on New surfaces of wall complete all as specified and directed.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43litre/10sqm over and including priming coat of exterior primer applied @ 0.90litre/10Sqm over Old/New surfaces of wall including necessary scaffolding required for painting work, safety measures etc complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area not exc.1.5 sqm each complete all as specified and directed.

Taking down shutters of any description, area not exc.1 sqm each complete all as specified and directed.

S & F for pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, as per ISI mark, including PCC (1:3:6), type C-0,( using 12.5 mm graded stone aggregates) as in filling of pressed steel frames complete all as specified and as directed .

Welding in repairs n.exc. 2.5 cm in length and thickness of metal/steel to be welded n.exc. 6mm complete all as specified and as directed.

Supply and fix for 30mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including second class hard wood plain cover fillets 35X6mm all around the shutters complete all as specified and as directed

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel ventilator with top hungshutter including hinges, steel pegstay, complete all as specified and directed by Engr - in - charge.

S & F for factory made solid Panel PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 4mm thick moulded PVC sheet on the front face and 4mm moulded prelam colour PVC sheet on back face wirth wood free EPS, fixed in frame at site as per specification and drawing including fittings complete all as specified and as directed.

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

Supply and fix for aluminium powder coated louvered ventilator with provision of exhaust fan using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed.

S & F for aluminium powder coated three track sliding window with two glazed shutters, one 4mm thick float glass ordinary quantity and one shutter of stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, PVC rubber lining etc complete all as specified and as directed. Catlouge numbers of Jindal company or equivalent make as specified. Sections of Jindal company : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

M&L machine cut Granite slab 18 to 20 mm thick as in walls,floor,steps, pillars, window cills, parapit tops,and like and incl 10mm thick (avg thickness) cement mortar 1:4 screeding and setting coat in cement morter 1:2:3mm thick, with araldite adhesives set and jointed with white cement sturry mixed with pigment to match the shade of slab incl cutting, waste, rubbing and polshing etc complete all as spd.Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish complete all as specified and directed.

S & F for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified Add Extra for Powder Coating to Item to (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S & F for anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.Add to item No for powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and directed.

S & F for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, ISI marked, complete all as specified and as directed.

S & F for 300mm long brass sliding door bolts with sand or die cast brass hasp, staple (bolt type) and fixing bolt with roller or drawn brass bolts, ISI marked, complete all as specified and as directed.

S & F for 200mm long aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed.

S & F for 150 mm long aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed.

S & F for butt hinges, 100mm size, mild steel cold rolled, medium weight complete all as specified and as directed.

Supply and fix for 75mm size butt hinges, extruded brass with mild steel hinge pin, bright polished and fixed type D-11 complete all as specified and as directed.

Supply and fix for floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, overall length of cover plate 150mm complete all as specified and directed.

Supply and fix for 100mm size brass handles, extruded, fabricated type, polished complete all as specified and as directed.

Supply and fix for 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

Supply and fix in repairs for 300mm, mild steel, ordinary rat tail rod pattern spring (helical spring) including roller and roller plate complete all as specified and as directed.

Supply and fix in repairs for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed

Supply and fix in repairs for floor door stopper of brass body and tongue with hard drawn steel spring of over all length of cover plate 150mm complete all as specified and as directed.

Supply and fix in repairs for 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

Preparation of new surface of wooden applying two coat of synthetic enemal paint over one coat of zinc chrome primer complete all as specified and directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore steel tubing with all fittings and connections including cleaning for refixing or removal to store complete all as specified and directed.

S&F for 20mm dia CPVC pipes SDR 11 including all Brass CPVC fittings for 20mm bore pipe on walls/ceiling or laying in floors and including 20 to 15mm dia fittings for fixing of sanitary fittings complete. Including taking up or down steel tubing and connections or removal to store complete all as specified and directed.

S&F for 15mm dia CPVC pipes SDR 11 including all Brass CPVC fittings for 15 mm bore pipe on walls/ceiling or laying in floors and including 20 to 15mm dia fittings for fixing of sanitary fittings complete. Including taking up or down steel tubing and connections or removal to store complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedding and pointed in any mortar complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7-8 mm thick,400x400 mm/ area exc 0.11sqm but nexc 0.18 sqm of each tile in floor etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile on 15mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed.

M & L for vtrified colour dark shade Ceramic tiles 10 mm thick (square/ rectangular) dark shade /ultracharged polished,Light shade area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match on 15mm thick screed bed in Cement Mortar 1:6 as specified

Glazed ceramic tiles in colour tiles vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match such as skirting /dados over 15 mm rendering in CM 1:4 complete all as specified and directed.

M & L 100 mm thick for cement concrete PCC type B-o , 1:2:4 12.50mm graded aggragate finishing concrete surface even and smooth as in subbase thick complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for cement concrete complete all as specified and directed.

M & L for Plinth protection 50 mm thick in PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) laid in alternate bays (not exceeding 2 Sqm each) finished even and smooth without using extra cement and providing joints complete all as specified and directed.

M & L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade A complete all as specified and directed.

S&F for glossy finished chequered cement concrete tiles 30cmx30cmx30mm /20 cm x 20cm x 25 mm (as approved) thick set jointed with grey cement and pigment and pointed in neat cement slurry with and including 15 mm thick screed bed of CM(1:6) in floors complete all over 25mm thick PCC 1:2:4 type B0 (using 12.50mm graded crushed stone agg , floor complete all as directed by Engr-in-Charge.

M & L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade on 15mm thick screed bed in Cement Mortar 1:4 over 25mm thick PCC 1:2:4 type B0 (using 12.50mm graded crushed stone agg , or floor complete all as directed by Engr-in-Charge.

Providing precast ce- ment concrete in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any sectionindicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match set in cement mortar 1:4 precast cement concrete type Bo 1:2:4 (12.50 mm graded aggregate )Ditto, but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

M & L for Walling of random rubble stone masonry, well bonded, bedded and solidly hearted built in cement mortar 1:4, brought up to courses, complete all as specified and directed.

All as per Item No 59.00, but except stone complete all as specified and directed.

M & L for raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cm 1:4 complete all as specified and directed.

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C-1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6, complete all as specified and directed.

Rendering 10mm thick on cement concrete block masonry/concrete surfaces in cement mortar 1:6 finished surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for one coats of cement base paint on old surfaces of wall complete all as specified and directed.

M&L for one coats of Ditto with distemper oil emulsion,old surfaces of wall/ceiling complete all as specified and directed.

M&L for one coats of white wash , old surfaces of wall/ceiling complete all as specified and directed.

Excavation in trenches not exc 1.50mtr wide and not exc 1.50mtr in depth for foundation etc and getting out in soft / loose soil complete all as specified and directed.

Returning filling in, well watering ramming in layers not exceeding 15cm thick complete all as specified and directed.

Removing of excavated soil to a distance not exc 50mtrs and depositingwhere directed at a level not exc 1.50 mtrs above the starting point complete all as specified and directed by Engr-in-charge.

Complete removal of entire existing water proofing treatment in any position including tarfelt, Plaster, lean concrete of any thickness, gravels etc. and removing the debries out side MD land complete all as specified and directed.

M & L for PCC 25 mm thick type B-0, 1:2:4 (12.5mm graded aggregate) as in roof surface complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:4 over concrete surfaces mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. Note: Water Proofing compound shall be measured and paid for seprately as "Supply Only" complete all as specified and directed.

Supply only water proofing compound complete all as specified and directed.

M&L Acrylic emulsion polymer of acrylic single component low viscosity polymer for preventing leakages over exisitng/New surface of slab, terrace, exterior, interior wall, Chajjas etc complete as per following procedure :- (a) Surface & surface preparation : Remove all the loose particles , dirt & dust clean by water , wire brush & mechanical cleaning , grease & oil should be cleaned using solvents, If the surface is previously coated with tar, it should be thoroughtly scraped off. The surface should be dry before application . All the cracks and crevices in the concrete slab to be filled with polyurethene based sealent with and including application of PU based primer all as directed by Engr-in-Charge. (b) Finish paint : Apply water based polyurethenene modified dispersion (single component cold applied ,non toxic,VOC complaint)in 03 coats icluding 01 coat of primer of same materials after dillution of water at 50 % or specific primer matching same material as per manufacturers specificationand as dircted by EIC/GE

M&L grouting the joints of flooring any type and any size of tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade 0.10 kg of hardener and 0.20 kg of resin per kg, including filling grouting and finishing complete as per direction of Engrineer -in charge

Hacking out old broken glass (any thickness, size quality of description) from wooden frames or stone, concrete or brick sorrounds, glazad with putty or fixed with beeds complete all as specified and directed.

S & F for sheet glass, 04 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F in Stainless Steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repairs 25mm dia stainlesss steel rods corrugated of approved quality complete all as specified and directed.

S&F in repairs stainlesss steel decorative end brackets suitable for 25mm dia pipes complete all as specified and directed.

Supply and fix for vitreous china coloured wash down water closet EWC cascade type ‘P’ trap / S trap in built seat cover and flushing cistern, low level, valveless, symphonic action type complete with inlet ball valve, float and handle complete all as specified and as directed by Engr In Charge

S & F for vitreous China wash basin, white, flat back, size 630x450mm including brackets including brass waste coupling, CP bottle trap 32mm size with 250mm & 190mm long wall connection pipe & wall flange, 15mm dia fancy type single lever tall boy swan neck pillar tap chromium plated with 150mm extention body fixed spout without popup waster system with 600mm long braided hoses complete all as specified and directed.

S&F Chromium Plated Push type, auto closing concealed Urinal Flush valve with wall flange complete all as specified and as directed.

S&F Bib taps fancy type chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as dierected.

S&F fancy type, chromium plated angular stop cock fixed with wall flange for 15mm bore of pipe complete all as specified and as directed.

S&F stainless steel grating doom 125mm dia complete all as specified and directed.

S&F soap dish any type fixed type fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F Hand shower (health faucet) (ABS Chromium plated) with 8mm dia, 1.2mtr long flexible tube and wall hook complete all as specified and as directed.

S&F 15mm dia bore, two way bib tap, long body, fancy type, brass chromium plated, with crutch handle, screwed down for uPVC/iron Pipe complete.

S&F brass chromium plated tubular towel rail 20mm dia including brackets both side complete all as specified and directed.

S&F brass chromium plated bracket for towel rail complete all as specified and directed.

M&L for 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L Gun metal globe or gate valve with iron wheel head screwed both ends size 20mm for iron pipe, fixed complete all as specified and directed.

M&L for cutting chases, pinning in brick, stone, concrete block walls making good to facings where required and pointing in cement mortar 1:3 to concealed water tubing and making good complete all as specified and directed by Engr-in-Charge.

M&L for PVC (SWR) waste and vent pipe 100mm bore in any length with rubber ring joint laid in floor or wall complete all all as specified.

S&F PVC (SWR) bends of any radius 110mm bore complete all as specified and directed.

S&F 110mm dia PVC (SWR) vent cowl complete complete all as specified and directed.

S&F PVC (SWR) junction double ( single T) of size 110mm bore jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) reducer 110mm to 75mm bore jointing with solvent cement complete all as specified and directed.

S&F 500 ltrs capacilty, Rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and in position including ball brass valve 20 mm high pressure with polythene float and fly nut complete all as specified and directed.

Dismantling wall /ceiling board (fiber,pulp,insulation,etc.incl all fitting ) or insulation board /slab/blankets, any thickness, including cover fillets.

S&F of gyproc white water proofing gypsum moisture resistance boards rectangular for false ceiling 10 mm thickness moisture resistance < 5% total water absorption, acoustic waterproofing suspended ceiling system with prima fine fissured tile with semi concealed grid, the tile should have humidity in module sizeof 600x 600x10 mm with Bio block coating on the face of the tile, impact resistant and suitable for green bldg application, eith recycled content of 63 %. The tile shall be laid on semi concealed grid system with 15 mm white flange incorporating 6 mm central reveal in white/black colour and with web height of 38 mm and load carring capacity of minimum 11.68 kg/sqm.Silhouette. main runner and cross tees to have mitred ends & birdmouth notches to provide mitred cruciform junction. The T sections have galvanising of 120 gms/sqm and passed through 500 hrs of salt test. all as per manufacutrer's instructions Complete all as specified and as directed.

E/M PORTION Taking down carefully aluminium / copper point wiring complete (light, fan socket & power) including unserviceable fixtures and fittings such as switches ceilimg roses pendents regulators sockets light fittings etc complete removing material for taking credit & making good disturbed wall / floor etc complete all as directed by Engineer-in-Charge.

Taking down sub main wiring complete including fitting and fixtures, removing materials for making good disturbed surfaces of walls, floors, roof etc, complete all as specified and directed.

Taking down carefully unserviceable DBs any type/size With MCCBs/MCBs//Isolator etc and disconnecting and making good disturbed surfaces complete all as specified and directed.

M&L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked including concealed PVC conduit and drawn through heavy duty PVC conduit fixed in walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, indluding cuttting and chasing, concealed modular flush boxes, modular cover plates with frame mounting for housing the switches, socket outlets etc, all as specified and directed . (a) One light point controlled by one way switch.

(b) One fan/exhaust fan point controlled by one switch and one regulator.

(c) One 3 pin switch socket outlet point 5 Amps on independent board.

(d) One 3 pin switch socket outlet point 5 Amps on same board with other switch.

All as per item No 107.00 with copper conductor cable for one 3 pin socket outlet, 15 amp independent, with cable 2.5 sqmm size complete all as specified and directed.

S & Fix modular switch 1 way 6A, 1 module complete all as specified and directed.

S & Fix modular switch1 way 16A, 1 module complete all as specified and directed.

S & Fix modular socket out let 6A 2/3 on combined 2 module complete all as specified and directed.

S & Fix modular socket out let 6A/16A-2/3 pin combined 2 module complete all as specified and directed.

S & Fix Ceiling rose surface backlite 65x50mm 3 terminals complete all as specified and directed.

S&Fix fan regulator electronic 2 modular type volts AC 50 HZ, 300 Watts,4step complete all as specified and directed.

Supply and fix 18/20 Watts LED plastic Batten (white / warm white as directed) with acrylic cover sleek design & high efficency for wall and surface mounted applicaiton with necessary braket, clamps, incl. bolts, nuts & washers for fixing arrangement etc complete all as specifed and directed .

M&L for lamp holder pendant/angle type insulated body with back plate complete all as specified and directed.

S & Fix of recess mounted 2' x 2' square LED panel 36 watts, Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling all as specified & directed.

S&F LED Tube light fitting 10 watt, 230 volts, sleek and seamless profiled extruded aluminium batten with an efficient diffuser to illuminate work and retail spaces complete with all accessories all as specified & directed by Engr-in-Charge.

S & Fix 30 Watts LED new generation energy saving and environmental friendly long life LED building light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08.

S & Fix 60 Watts LED new generation energy saving and environmental friendly long life LED building light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08 complete all as specified and directed.

Taking down the defective ceiling fan / Exhaust fan of any sweep and make after disconnecting electrically & mechanically and examine & carry out the servicing/overhauling the ceiling fan by thoroughly cleaning the bearing, shaft, stator, rotor & applying the lubricant / grease to the bearing including applying one coat of painting re-fixing, testing in all respect for smooth running complete all as specified and directed.

Supply and fix ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, Five star rated with brushless direct current motor (BLDC) and deposit the old fan to the store complete all as specified and directed.

S&F exhaust fan, AC, single phase, 240 V, 250 mm sweep, PVC body with louvers, including connected with 3 core 1.5 sq mm copper conductor cable from ceiling rose to exhaust fancomplete all as specified and directed.

S & Fix double door sheet metal enclosure distribution board TPN, 4 ways 240 volts, with 200 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed including taking down old MCB DB complete all as specified and directed.

S & Fix double door sheet metal enclosure distribution board SPN, 8 ways 240 volts, with 200 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed including taking down old MCB DB complete all as specified and directed.

S & Fix double door sheet metal enclosure distribution board SPN, 12 ways 240 volts, with 200 amps rated bus bar, with IP 43 protection and double door, suitable for mounting MCBs all as specified and as directed including taking down old MCB DB complete all as specified and directed.

Supply and fix MCB Four pole, 415 volts, 40 Ampere, rupturing capacity 16 KA, in the DB complete all as specified and directed.

S & Fix of MCB single pole and neutral, 240 volts, 6 to 40 Ampere, rupturing capacity 10 KA, ‘C’ series complete all as specified and directed.

S & Fix of MCB single pole, 240 volts, 6 to 40 Ampere, rupturing capacity 10 KA, ‘C’ series complete all as specified and directed.

S & Fix sheet metal enclosure distribution board SPN DB's 2 way with MCB complete all as specified and directed.

M & L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC casing and capping with its accessories all as specified and directed by Engr-in -charge for the following:- (a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

(b) 2x2.5 sq mm and 1x2.5 sq mm as earth wire

(c) 2x6.0 sq mm and 1x6 sq mm as earth wire

M & L for submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable , multistranded on the surface through and including suitable size of PVC conduit concealed in walls/floors with its accessories all as specified and directed by Engr-in -charge for the following:- (a) 2x1.5 sq mm and 1x1.5 sq mm as earth wire

(b) 2x6.0 sq mm and 1x6 sq mm as earth wire complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth and getting out in Soft / loose soil including forming bottom surface etc complete all as specified and directed.

Returning, filling in including spreading, levelling ,watering and well ramming in layers not exceeding 25 cm thick complete in soil complete all as specified and directed.

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 50 mtr above the starting point complete all as specified and directed.

Supply & Laying 50 mm outside dia double wall corrugated pipe (DWC) of HDPE ISI Mark for enclosing cable below ground / road surface, to a required depth, including suitable size coplers for jointing of pipe all as per site requirement

M &L for GI pipe light grade in repair for road crossing / on wall / on pole for cable protection of 50mm dia complete all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode 60x60cmx06mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed. NOTE: GI Earth lead wire & GI pipe upto 7.5 m length is deemed to be included in the quoted rate.

J.G.Goel (BID ID -3155163)

Mehta and Co. (BID ID -3146749)

sagar construction (BID ID -3155214)