Renovation/rehabilitation of various building under IGMC Shimla (SH- replacement of roofing of Ortho OPD, Block D porch, renovation of waiting area and Ortho OPD etc

Amount

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within all leads and lift complete including carriage of materials within all leads and lifts.For thickness of tiles 10 mm to 25 mm

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within carriage of material in all leads and lifts:-Multi Wall polycarbonate Sheet.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto all leads and lifts, including getting out the excavated soil and disposal of surplus excavated soil as directed, within all ledas and lifts. (i) All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) including carriage of materials in all leads and lifts.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc:- Sal wood complete in all respects as directed by the Engineer-in-charge including carriage of materials in all leads and lifts.

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). including carriage of materials within all leads and lifts.(i)9mm thick commercial ply conforming to IS : 1328 BWR type

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). including carriage of materials within all leads and lifts.(i) 12mm thick commercial ply conforming to IS : 1328 BWR type

Providing and fixing 12 mm thick Pine Wood wood Tongued and Grooved lining of approved quality with butt jointing and nails(frame work and cover fillets to be paid for separately).including carriage of materials in all leads and lifts.

Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood.(i) 50x50 mm (base and height) including carriage of materials in all leads and lifts.

Providing and fixing 19mm thick commercial board in shelves/box for cup board with butt joints and fixing with nails and screws etc. complete including carriage of materials in all leads and lifts.

Providing and fixing 19mm thick Commercial Board shutters for Cup boards i/c fixing with nickel plated piano hinges with screws etc complete including carriage of materials in all leads and lifts.

Providing and fixing square edged cover fillets (beading) 19 x 6 mm section including mitring at junction with wooden screws / nails etc complete of hard wood including carriage of material in all leads and lifts.

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18mm X5mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge including carriage of materials in all leads and lifts.

Providing and fixing 1.00 mm thick coloured or plain laminated sheet (sunmica) on boards / ply wood sheets with approved adhesive and nails complete including carriage of material in all leads and lifts.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete including carriage of materials in all leads and lifts.. (i) Triple strip vertical type

Providing and fixing Stainless Steel. Haps and Stapples with necessary screws etc. complete :(i) 90 mm including carriage of materials up to all leads and lifts.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lifts.:(i) 125mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) including carriage of materials within all leads and lifts.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15) including carriage of materials within all leads and lifts.

Providing and fixing 12mm thick preleminated partical board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. Pre-laminated particle board with decorative lamination on both sides complete including carriage of materials in all leads and lifts.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -in-charge. (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) including carriage of materials within all leads and lifts.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials in all leads and lifts.(i) 250x16mm

Providing and fixing Aluminium hanging type floor door stopper with necessary screws, etc. complete including carriage of materials within all leads and lifts.

Providing and fixing Aluminium Powder coated American Handles (of approved quality) complete including carriage of materials in all leads and lifts. (i) 300 MM

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.(i) With stainless steel cover plate minimum 1.25 mm thickness including carriage of materials in all leads and lifts.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :(i) Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials in all leads and lifts.

Providing and laying granite stone in wall linning/ flooring etc. 20mm(average) thickness base of cement mortar 1:3 (1cement:3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of materials within all leads and lifts:- 20mm thick.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete within carriage of material in all leads and lifts.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. including carriage of materials in all leads and lifts.

Providing and fixing prepainted galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as per the direction of Engineer-in-Charge including carriage of material in all leads and lifts.

Providing and fixing prepainted galvanised steel sheet roofing accessories 0.50mm (+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete including carriage of materials in all leads and lifts:- Ridges plain (500 - 600mm).

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. including carriage of materials in all leads and lifts.

Steel work bolted in built up sections,including cutting , hoisting ,fixing in position and applying priming coat of red lead paint Including carriage of material within all leads and lifts.(i) In Gratings Framed Guard Bars Ladders and similar works.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.(i) Hot finished seamless type tubes

Providing and fixing M.S. BP sheet 1.66 to 2.00 mm thick in eaves board/facia/soffits/ceiling including cutting , fixing and welding to steel roof member and applying a coat of red lead of primer complete in all respect as per directions of the Engineer-in-Charge.including entire carriage of materials in all leads and lifts

Providing and fixing Powder coated aluminium tower bolts (barrel type) with necessary screws etc. complete .including carriage of materials with in all leads and lifts.(i) 200x10mm

Polishing two or more coats with malamine polish of required shade on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler including carriage of materials in all leads and lifts.

Painting one coat (excluding priming coat) on previously painted wood and wood based surfaces with enamel paint to given and even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping including carriage of materials in all leads and lifts:-With white enamel paint.

Painting one coat (excluding priming coat) on previously painted steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foreign matter including carriage of materials within all leads and lifts in With white enamel paint.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters including carriage of materials with in all leads and lifts complete in all respect as per the direction of Engineer - in Charge. (a) Enamel paint other than white

Painting two coat (excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping including carriage of materials within all leads and lifts in With white enemal paint.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting including carriage of materials within all leads and lifts in Readymixed paint brushing with white lead for priming.

Applying one or more coat of paint based putty made of whiting and POP etc. mixed in required quantity of white enamel paint for application on wood based products after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials within all leads and lifts.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50grams/ litre ( fifty grams per litre ) of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour Two coats complete including carriage of materials in all leads and lifts and as directed by the Engineer in Charge.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.including carriage of materials within all leads and lifts.

Providing and applying white cement based putty of average thickness 1.00mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials within all leads and lifts.

Providing and fixing NRV Packers for PU grouting work including carriage of materials with in all leads and lift.

VIKAS GAUTAM