Providing Additional Work for New office Building in Sivakasi City Municipal Corporation

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Supplying and filling in foundation and basement with Crushed Stone Sand (M- Sand) in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

For Wall upto 1.80mm

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) For plane surfaces such as rectangular or square RCC Beams top and bottom slab of RCC boxing, etc.

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 350Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. For Plinthbeam and foundation

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Painting two coats with ready mixed exterior Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealent on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealent with necessary spatula etc., complete complying with standard specifications and as directed

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating as per Design given by the departmental officers etc, complete as per standard specification

Providing and fixing Bitumen Pad for Expansion joint in between pavement slabs to 12mm thick and fixed as shown in the drawing including cost and conveyence of expansion joints including shalimar pad and joint sealent etc, complete as per standard specification

Supply and placing of Black jet granite including the cost all materials etc.,complete, in front elevations

Granite Nosing for Steps/Platform of full round with smooth finishing including cost of Labour, machinery etc., complete.

Supplying and laying in flooring with fully polished Sinthetic Grey colour Granite stone of 20mm thick (average) of 4' X 2' in size laid over base layer of cementmortar 1:3 (one cement and three sand) - 20 mm thick and applying cement slurry &pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the deparmental officers

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Laying the Flooring with Anti skid coloured ceramic tiles of sizes 305mm X305mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:3 (one cement ,three sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification.

Supplying & Fixing of in the position of best approved colour design & quality of polycarbonate sheet 6mm thick with necessary "u" & "J" Bolts etc completed.

Supplying & fixing door shutters for Medium Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete.

Supplying and Installing metal false ceiling using fire reardant galvanized steel sheet plan lay in tiles size 600mmx600mm, 0.5mm thick, powder coated on external surface grid and shall have flange on all four sides to rest on the exposed grids. (PWD Sor 19-20)

Supplying and Fixing Teak wood Door panelled shutter with frame for door Fully panelled with 50mm Thick T.W. planks the door shutter Styles will be 75mm x40mm & Top rail 100 mm x40mm the lock rail will be of 125mm x40mm and the bottom raill will be 150mm x40mm and including cost of furniture fittings and cost of wind appliances and Labour charges for fixing Furniture etc and fixing up shutters in position and best french (Lac) polishing with two coats . T.W. doors windows ventilator including cleaning the surface etc., complete complying with standard specifications ..

FRP door Shutter with FRP door frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3mm wall thickness for styles and rails etc., of sizes specified by Engineers.

Providing Wall Panelling using one side teak wood sheet with melamine polishing with following specification. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both diretions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws. One side teak wood sheet of 3.5mm thick will be fixed over the plywood using fevical and finishing with melamine polishing and the rate inclusive of conveyance to site and labour charges and as directed by the Departmental Officers. The design pattern, water proof plywood, OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work etc., complete.

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing in position of Alu. Anodised Partition with 62x38x2mm extruded box section at bottom vertical and horizontal members. The vertical member are spaced at 90 cm c/c and to horizontal members are spaced at 1.2M, 2.1M and 2.4M height the bottom panels should be covered with 12 mm thick PLB exterior grade and the top and middle panels should be fixed at 4mm thick glass thick glass with necessary glassing clips.rubber beading, etc., including necessary dismantling holes in RCC columns, beams masonry wherever necessary with power power drill ti the extent required and made good to the original conditions after fixing as directed by the departmental officers. All the Aluminium sections should be anodised to 1.5microns as per ISI specification 1868/1962.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on wor

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes, Bemds, other clamps, screws nails etc., complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications. 160mm dia pipe

110mm dia pipe

75mm dia pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). 110mm dia PVC Elbow

110mm dia PVC Elbow with door

110mm dia PVC Y

75mm dia PVC Elbow

Internal Water Supply Arrangements using PVC pipes and PVC specials Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. Internal Concealed Line 25mm dia

Internal Concealed Line 32mm dia

Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements 25mm Elbow

25mm Tee

32mm Elbow

32mm Tee

32 mm x 25 mm Reducer Elbow

Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellac , thread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. 25mm Gun Metal Valve

32mm Gun Metal Valve

Suppling and fixing in position 15mm.diameter brass / C.P screw down tap / pillar tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary SD Tap

Pillar Tap

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing of SS Sink of size 1200 x 550 x 180mm

Supplying and fixing in position 15mm dia C.P.Shower rose & stop cock of approved make confirming to IS specifications and qulity including cost of Shellac thread etc. complying with standard specification. C.P. Shower Rose

C.P Stop Cock

C.PAngle Cock

Supplying and fixing in position Indian make bewelled edge mirror of size 600 x 450mm quality including cost of Rawal plugs, brass screws. etc. complying with standard specification.

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications

Supplying and fixing in position C.P. Soap tray of size 150 x 150mm including cost of teak wood plug and C.P. screws. etc. complete complying with standard specification.

Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm 'P' os 'S'' trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings etc., complete complying with standard spoecifications,labor inclusive of fixing lowlevel flushing tank.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm White/Colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with Sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two Sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). White

Supplying and fixing in position of Indian Make White/Colour glazed earthen ware lipped mouth Flat Back Urinal of best approved quality with G.I.Pipe connection to suitable length,32mm bell mouthed P.V.C connection ,15mm dia G.M.Wheel valve,fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc.,including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and wheel valve ,painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. -

Supply and fixing of PVC. Nahini / Floor Trap with stainless Steel Gratings- 100 mm x 75 mm including all charges etc, complete as per standard specification.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supply and delivery of clear water vertical wet type submersible pump suitable for 150mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS 9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5%

Supply and delivery of 3 phase panel board star delta with two level guard and auto start to suitable for 10 HPsubmersible pump set etc. complete

Supply and delivery of Open well Submersible pump set conforming to IS 14220/2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (#5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

Supply and Delivery of 150mmdia UPVC casing Pipes including cost and conveyance of materials and Labour charges etc. complete as per standard. Specification

Supply and delivery of 3 phase panel board star delta with two level guard and auto start to suitable for 10 HPsubmersible pump set etc. complete

Supplying delivery of G.I and PVC Pipes and specials of approved quality and best verity of B Class pipe including cost conveyance of materials to work site etc., complete. Connection to tank 50mm GI Pipe

50mm Dia G.I Coupling

50mm Dia G.I Elbow

50mm Dia G.I Union

50mm Dia Non Return valve

40mm Dia G.I pipe

40 mm Dia G.I Coupling

40 mm Dia G.I Elbow

40 mm Dia G.I Bend

G.I Reducer 50 x 40 mm

Supply and fixing of 48W LED Outdoor street light fitting (Philips/Havells) complete with T.W round blocks on wall or ceiling with flu tube with PVC unsheather copper leads from terminals to the filling

Supply of Early Streamer Emission Air Terminal (ESEAT). Model: L The ESEAT has corrosion resistant stainless chrome body made up of AISI 316 grade of height 0.50 metres capable of working in hazardous atmosphere. The Air terminal is non-adioactive and requires no special licensing. The unit is fully autonomous (no battery, no external power supply is required), collects energy from the ambient electric field.The ESEAT model has been tested in a high voltage laboratory in accordance with NFC 17 102 in order to measure the average gain in triggering. The average gain in triggering time (ΔTs) obtained during the lab test for the offered model is 60 μs. The ESEAT works on negative as well as positively polarized discharges. ESEAT has been tested for such discharges in Central Power Research Institute (CPRI). A dedicated tester is avilable to test the healthiness of the ESEAT on request (Page No. 37, Point No. 3 of Clause .6 of the Revised NFC 17-102 version 2011 ). ESEAT Model : L - Radius of protection : 86 MetresLevel of protection considered for the Project-II level

MOUNTING STRUCTURE: Supply of Standard / Speciat Moun 4.5 mts. pipe, and 300 x 300 x Bmm MS plate, 3 mts. 48mm OD class C GI outer Pipe, 1.8 mtr,38mm OD inner PiPe, for roof mounting on concrete base and with FRp adapter (ED P.No 45 item No.2)

DOWN CONDUCTOR: Supply and run of 25mm x 6mm with necessary clamps / supports for earth connection

TEST LINK: Supply of Test Link Box for each Down to disconnect the earth termination measurement of resistance conductor in ordersystem to enable

EARTH ELECTRODE: Supply and insallation maintenance free Gl Eartfiing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 1OO micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp

SURGE PROTECTION: Supply and insallation cabinet Type Class 1 and 2 Combined Model SPD to arrest surges and overvoltages in the power line due to lighning switching action etc. they must be installed in the incoming MCC panel / DB of ther espective buling in paraller to the power circuit. Model: PSV4 -L2.s/4o0TT (3 phase power network)

Supply and fixing of 18W LED 3000K Round Type Recessed Fitting with LED with PVC unsheathed Copper leads from terminals to the fitting (DATA- D)

Supply and fixing of 50W Mono colour flood light luminaire (JETA QUANTO PLUS / equ) with PVC unsheathed Copper leads from terminals to the fitting with angle iron suport on masonary pedestal (DATA -E)

Supply and fixing of 8W LED BOLLARD Fitting (JETA CONE NXG / equ) with PVC unsheathed Copper leads from terminals to the fitting with angle iron suport on masonary pedestal. (DATA F)

Supply and fixing of LED Decorative Golden crystal chandelier with PVC unsheathed Copper leads from terminals to the fitting (DATA-G)

Supply and Installing CCTV 13mp hd resoution dome camera inlcuding cable fixing and all erection charges etc complete CCTV Setup box including hard disc capacity 10TB including cabling works all accssories etc complete. Supply of CCTV camera

Hard disc for NVR

Rack With Accesssories -12U

Armoured LAN & CCTV Cable

Supplying of 10'x 8' Motorized screen

Supplying of 3*1.5 Sqm

Supplying and planting of Mexican lawn in & australian dipling method etc., Complete with all labour, lead and lift and as directed by the engineer-in charge. (All labour, materials, tools and plants etc., by contractor)

Supplying of 10ft Height foxtail palm and planting charges

Supply of ornamentalplants (5ft height) ficus, Exora, Christmas tree,..etc

Supplying diffreent types of border plants 1 feet height and planting labour charges

Supplying and fixing of aluminium dye cast letters of approved size and colour. The colour treatment process is achieved with MRF Colour coat and then the processed coloured layer is set into th klin for the heat treatment process for the following sizes. 60cm(24")

Emblem(15")

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Modular switch box and 5A 1M switch in flush with wall with Cover Plate sheet cover for making good of the concealed portion with suitable colour for PVC concealed modular light point/ fan point (for electronic regulator) (5 pts / coil) (SD-24)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with Modular switch box and 5A 1M switch in flush with wall with Cover Plate sheet cover for making good of the concealed portion with suitable colour for PVC concealed modular light point/ fan point (for toilet / bathrooms) (6 pts / coil) (SD-26)

Wiring with 3 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 1M flush type modular box with cover and 5A FT 1M switch (two way) and making good of the concealed portion with suitable colour for concealed staircase light point (SD-32)

Supply and fixing of single box type 4' 36W LED Wall fitting complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting. (SD-87)

Supply and fixing of single box type 4' 40W LED complete with conduit pipe suspension from ceiling with PVC unsheathed copper leads from terminals to the fitting with LED Tubes (SD-91)

Supply and fixing of 18W square type LED on ceiling with necessary accessories and electrical connection.

Supply and fixing of 24W square type LED on ceiling with necessary accessories and electrical connection.

Supply and fixing of 50W Low bay LED fitting on ceiling with necessary accessories and electrical connection.

Supply and fixing of 9W LED bulb for BH point with electrical connections complete.

Supply and fixing of 15watts WT bulk head fitting with guard with 15W LED bulb with electrical connections complete. (for Semi basement) (using Run of)

Supply and fixing of 1200mm sweep (48") AC ceiling fan High speed complete with stepped electronic 100W 2M regulator with 1.2 mtr down rod on the existing clamp

Supply and fixing of Cabin fan on wall mounting 300 mm sweep with necessary accessories and connections complete.

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch (SD 105)

Supply and fixing of 375mm (15") sweep (Heavy-duty) AC exhaust fan complete without provision of holes in the wall. (SD-117)

Supply and fixing of louvers shutters arrangements for 375mm (15") sweep AC exhaust fan (SD 121)

Supply and fixing of 2M 6A 5 Pin Socket-1 No, lM 6A Switch - 1 Nos in 3M Flush Box with cover Plate in flush with wall and connection (For Set plugs)

Supply and fixing of 16A, 3 pin switched socket 3M in Modular Flush Box and Covered with Cover plate, flush with wall and connection

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For Geyser Plug) (SD 140)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure Distribution board with Double door type with metal door with IP42 protection with 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like Legrand make).

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure Distribution board with Double door type with metal door with IP42 protection with 1 No. 32A DP MCB as incoming and 10 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like Legrand make).

Supply and fixing of 63A Horizontal type 4way triple pole neutral MCB distribution board in sheet steel enclosure double door of double door type with metal door with IP 42 protection with 63A 4 pole MCB isolator as incoming, 6 nos 32A DP MCBs as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (like Legrand make)

Supply and fixing of 63A Vertical type 6way triple pole neutral MCB distribution board in sheet steel enclosure double door of double door type with metal door with IP 42 protection with 100A 4 pole MCB isolator as incoming, 18 nos 6-32A SP MCBs as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark (like Legrand make)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 55)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 57)

Supply and run of 4 of 6 sq.mm.(84 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 63)

Supply and clamping of 3½ x 25 sq.mm PVC LTUG armoured LTUG Alu. cable on post or on wall with MS Clamps. (SD 222)

Supply and fixing of brass cable gland for PVC armoured 3½ x 25 sq.mm LTUG cable with earth connection. (SD 186)

Supply and providing cable end termination of 3½ x 25 sq.mm.PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD 235)

Supply and laying of 2 x 6 sq.mm PVC armoured LTUG Alu. cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (SD 197)

Supply and clamping of 2 x 6 sq.mm. PVC LTUG armoured Alu. cable on post or on wall with MS clamps (SD 215)

Supply and fixing of brass cable gland for 2 x 6 sq.mm. PVC armoured LTUG cable with earth connection (SD 181)

Supply and fixing of 32A DP switch of 500V with metal clad with fuse and neutral (side handle) on suitable TW board with earth connection only (For Street light control) (SD 144)

Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured LTUG Alu. cable on post or on wall with MS Clamps. (SD 221)

Supply and fixing of brass cable gland for PVC armoured 4 x 16 sq.mm LTUG cable with earth connection. (SD 185)

Supply and fixing of 65 mm (2 ½") GI pipe (Class 'B') of 6 mt. Length with 300mm x 300mm x 6mm MS base plate, duly welded at the bottom with concreting with construction of Masonary pedestal with suitable sintex box to house 1 nos. 6-32A SP MCB etc. with suitable angle iron frame work and with supply and fixing of 1 no. 48W LED street light fitting with with cowl arrangements with1 metre of 32mm dia GI pipe (Class 'B') complete, with necessary clamps, on the above post with PVC unsheathed leads with painting of suitable colour. (Data Y)

Supply and fixing of 3 phase 200A aerial fuse unit for 3 Nos. 200A fuse units (500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work on the tapping pole with necessary clamps (Data A1)

Supply, Erection, Testing and Commissioning of 415V/50 Hz 200 A Cubical panel board of size of 5 feet x 5 feet x 1.5 feet with following switches, bus bar chamber and cable chamber on extreme end with 16 SWG thick CRCA sheet with 1"x ¼ " tinned copper flats for 3 phases and neutral with 6mm hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus supports at equal intervals as per IS specification and 2 runs of 1"x 1)8" copper flat on rear side of the panel board for earth buses and with 0-500V digital Voltmeter (0-200) Digital Ammeter CT, with one set of LED pilot lamps set with fuse base, top & l0A HRC fuse link for 3 phases on a separate chamber and with the following switches complete. 1) 200A TPN Double Break switch -1 No 2) 100A TPN Double Break switch -2 Nos 3) 63A TPN Double Break switch - 4 Nos. 4) 32A TPN Double Break switch - 3 Nos. and S & F of 1 No Digital L&T make multifunction meter. and inclusive of Fabrication charges, Erection charges and Commissioning and with 1 No Metallic danger board with powder coated painting, necessary identification of outgoing loads, bus capacity, cable size etc., with bold letter (Data - A5)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection (SD 76)

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work (SD 234)

Supply and Fixinng of 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle

Supply and Fixinng Shock Treatment Chart fixed in glass frame

Supply and Fixinng First Aid Box complete with all First Aid Medicines

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers

Supply and fixing of Carbon-di-Oxide Gas Type 2 kg.capacity Fire Extinguisher as per New IS15683,complete with control valve, discharge hose with horn,wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers.

Supply, erection, commissioning and testing of 62.5 KVA Diesel generator set with acoustic arrangements in accordance with CPCB norms, water / coolant oil cooled type engine with not less than 90 BHP for 62.5 KVA generator at 1500 rpm under NTP conditions with following specifications. The engine should have turbo charged, should be provided with air cleaner, base frame, crank case, lubricating oil, fan and fan drive, fuel and oil filters, flexible fittings, exhaust governor, hydro-mechanical gauges for fuel pressure and oil pressure, tachometer, digital water temperature gauge, charging arms, muffler, exhaust pump for fuel priming, fuel transfer, jacket with radiator engine oil, safety set ups with engine shutdown system

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid- 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP 1 No. (d) Vertical Pump 2-9, 2.00 HP/Single Phase 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA)- 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20" Filter with Housing - 1 No., Low Pressure Switch- 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. RO of 250 litres

Supply, erection, Testing and commissioning of 13 passengers lift Gearless without machine room as per standard specifications. (SR)

Supply and fixing of 2.0 TR Split AC with 5 KVA stabilizer with copper coils 5 star rated of reputed make with required accessories and as directed by the departmental officers

MRADHAKRISHNAN (BID ID -1112983)