State border to Savalde, Karit, Ranala, Shanoumandal, Chadvel, Brahmanvel, Dahiwel upto Pimpalner from Morvis upto Savali Vihir (Improvement to Prakasha Chhadvel Dahivel Samode Raod SH-7 Km.80/00 to 81/200 and 90/00 to 92/00 Tal.Sakri Dist.Dhule)

Excavation for catch / side water gutter in all sorts of soils to the specified section including stacking the excavated stuff in a regular bund and disposing of unsuitable or excess stuff as directed all sorts of soils.

Providing earth work in embankment with approved materials obtained from departmental land upto lead of 50 metre including all lifts, laying in layers of 20 centimetre to 30 centimetre thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with vibratory roller to achieve not less than 97 % of standard proctor density Etcetera complete (Material obtained from departmental Land)

Watering and compacting of embankment formed of materials obtained from the road cutting within a lead of 50 metre, not less than 97 % of standard Proctor density after laying them in layers of 20 centimetre to 30 centimetre with vibratory roller.

Dismantling of existing Black Top Surface (flexible Pavement) to a depth of 50 milimetre manually including loading of dismantled material to transport vehicle at site excluding lead charges.

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 metre and spreading for embankment or stacking as directed.

Conveying materials obtained from road cutting including all lifts, laying in layers of 20 centimetre to 30 centimetre breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard Proctor density for a lead of over 50 metre to 300 metre inclusive from the site of excavation to the site of deposition as directed.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at Optimum Moisture Content, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material

Construction of dry lean cement concrete Sub-base over a prepared sub-grade with coarse and fine aggregate (natural sand/ Verticle Shaft Impactor grade finely washed crushed sand) conforming to Indian Standards: 383, the size of coarse aggregate not exceeding 25 milimetre, cement content not to be less than 150 kilogramme per cubic metre, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etcetra complete. with fully automatic micro processor based Programmable logic controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetra complete.

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to Indian Standards 3395 : 1997 below concrete pavement including all materials and labour complete.

Providing and laying in-situ Mix-40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand/ Verticle Shaft Impactor grade finely washed crushed sand) conforming to Indian Standards 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @ 0.6 metre X 0.6 metre centre to centre, admeasuring 80 milimetre at bottom and 40 milimetre at top with depth of 75 milimetre and maintaining the same throughout curing period by any other method approved by Engineer-in-charge. with fully automatic micro processor based Programmable logic controller with Supervisory Control and Data Acquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etcetra complete.