Construction of residential colony sub division office type IV and type III in Bhognipur Division LGC Etawah

Amount

Clearing jungle including uprooting of trunk vegetation grass bush wood trees and sapling of girth upto 30cm. Measured at a height of 1 meter above ground level and removal of rubbish upto a distance of 50m. outside the periphery of area cleared including all labour, material, t&p as per direction of Engineer-in-Charge.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains All kinds of soil (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. as per direction of Engineer-in-Charge.

Diluting and injecting chemical emulsion for post-constructional anti-termite treatment (excluding the cost of chemical emulsion) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration i/c all material, labour, t&p as per direction of Engineer-in-Charge.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming drassing and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete as per direction of Engineer-in-Charge.

Supplying and filling sand in plinth under floors, including watering, ramming, consolidating and dressing complete as per direction of Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40mm nominal size derived from natural sources) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Brick work with common burnt clay (non modular) bricks of class -150 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Brick work with common burnt clay (non modular) bricks of class -150 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Providing and laying in position M-20 specified grade of reinforced cement concrete excluding the cost of centering, shuttering & reinforcement - All work up to plinth level in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge. Up to plinth level

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge. Above Plinth Lvl

Reinforced cement concrete work in beams, suspended floors, roof having slope upto 15 degree, landings, balconies, shelves, chajjas, lintels, bands, staircases and spiral staircases etc. above plinth level up to floor V level, excluding the cost of centering, shuttering, finishing and reinforcement : in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge. [i] Upto Plinth Lvl

[ii] Above Plinth Lvl

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500 D or more including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-lIl) derived from natural sources : 4 graded stone aggregate 12.5 mm nominal size derived from natural sources) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Half brick masonry work with common burnt clay (Non modular brick of Class designation 7.5 in super structure above plinth level upto fifth floor level in all shapes and sizes in cement mortar 1:4 (1 cement : 4 coarse sand ) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Brick work with common burnt clay bricks of Class designation M-150 in super structure above plinth level upto fifth floor level in all shapes and sizes in cement mortar 1:6 ( 1 cement : 6 coarse sand ) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators frame, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings, glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment) including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

M.S. steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. In grantings, frames, guard bar, ladder, railing, brackets, gates and similar works including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Providing second class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length including their cost including all royalty, labour, material, t&p as per direction of Engineer-in-Charge

Providing and fixing brass tower bolts, approved quality & make with necessary screws etc all complete including all royalty, labour, material, t&p as per direction of Engineer-in-Charge. 250 x 10 mm.

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, including all royalty, labour, material, t&p as per direction of Engineer-in-Charge. [i] Door Chaukhat

[ii] Window Chaukhat

[iii] Vent. Chaukhat

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary fixtures & extra for cutting rebate in flush door shutters including all royalty, labour, material, t&p as per direction of Engineer-in-Charge.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1 mm thick including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory, all complete with 4.0 mm thick glass panes including all labour, material, t&p as per direction of Engineer-in-Charge.

12 mm thick cement plaster of mix 1:6 ( 1 cement & 6 coarse sand ) including all labour, material, t&p as per direction of Engineer-in-Charge.

15 mm thick cement plaster of mix 1:6 ( 1 cement & 6 coarse sand ) including all labour, material, t&p as per direction of Engineer-in-Charge.

15 mm thick cement plaster of mix 1:4 ( 1 cement & 4 coarse sand ) including all labour, material, t&p as per direction of Engineer-in-Charge.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ) finished with floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. 40 mm thick floor 20 mm nominal size stone aggregate including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing & laying rectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to be specified by the manufacturer), of 1st quality confirming to IS:15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grounting the joints with white cement and matching pigmrnts etc., complete including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete including all labour, material, t&p as per direction of Engineer-in-Charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : (25 mm thick) including all labour, material, t&p as per direction of Engineer-in-Charge.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mmincluding all labour, material, t&p as per direction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture including all labour, material, t&p as per direction of Engineer-in-Charge.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre including all labour, material, t&p as per direction of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) . (a) 250mm x 16mm. including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 250mm x 10mm.

(b) 200mm x 10mm.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) (a) 125 mm. including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer in M.S. tube including all labour, material, t&p as per direction of Engineer-in-Charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete including all labour, material, t&p as per direction of Engineer-in-Charge.

Centering and shuttering including stutting, propping etc. and removal of form work including all labour, material, t&p as per direction of Engineer-in-Charge. (i) Beam /Bend

(ii) Column

(iii) Foundation

(iv) Slab

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required including all labour, material, t&p as per direction of Engineer-in-Charge. (a) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Same as above but for European type W.C. pan with white plastic seat and lid. including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including all labour, material, t&p as per direction of Engineer-in-Charge. a) White Vitreous China Flat back wash basin size 550 x 400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink with drain board as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required including all labour, material, t&p as per direction of Engineer-in-Charge. 510 x 1040 mm bowl depth 250 mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete including all labour, material, t&p as per direction of Engineer-in-Charge. Semi rigid pipe (a) 32mm dia

(b) 40mm dia

Supplying & Fixing of C P soap tray fixed to the wall with PVC rubber plug with C P brass screws including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of approved quality including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing & fixing PVC pipes conforming to IS make workinh pressure 6 Kg/cm² including testing, labour, T&P and all complete fittings including all labour, material, t&p as per direction of Engineer-in-Charge. 110mm dia

75mm dia

Providing and fixing on wall face PVC moulded fittings/accessories for PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. (Make : Supreme / Finolex / Prince) including all labour, material, t&p as per direction of Engineer-in-Charge. Bend 110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete including all labour, material, t&p as per direction of Engineer-in-Charge. (internal work) [i] Exposed on wall 25mm dia nominal dia pipes

32mm dia nominal dia pipes

40mm dia nominal dia pipes

[ii] Concealed work, including cutting chases and making good the walls 15mm dia nominal dia pipes

20mm dia nominal dia pipes

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 15mm nominal bore

Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 15mm nominal bore

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 15mm nominal bore

Providing and fixing gun metal gate valve with wheel of approved quality including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 25mm dia nominal bore

(b) 32mm dia nominal bore

(c) 40mm dia nominal bore

Providing and fixing brass stop cock of approved quality including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 15 mm nominal bore

(b) 20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including all labour, material, t&p as per direction of Engineer-in-Charge.

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m including all labour, material, t&p as per direction of Engineer-in-Charge. (a) Pipes 80mm to 300mm diameter.

Providing, laying and joining glazed stone ware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 100mm diameter

(b) 150mm diameter

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 100mm diameter S.W. Pipe

(b) 150mm diameter S.W. Pipe

Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. grating, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design including all labour, material, t&p as per direction of Engineer-in-Charge. 150 x 100 mm size P type

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg) With FPS bricks of class designation 75 as per standard design including all labour, material, t&p as per direction of Engineer-in-Charge. (i) For Sewer Line

Providing and fixing CP Brass bib cock of approved quality including all labour, material, t&p as per direction of Engineer-in-Charge. (a) 15 mm nominal bore

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. including all labour, material, t&p as per direction of Engineer-in-Charge.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required including all labour, material, t&p as per direction of Engineer-in-Charge. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Supply and fixing of LED Tube Light with batten suitable for upto 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. - CAT-AAA including all labour, material, t&p as per direction of Engineer-in-Charge.

Supply of Ceiling Fan with fan motor of A.C. permanent insulation, capacitor rating conforming BEE 5 Star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated voltage 220/240 volts, 50Hz, 1-ph AC the fan assemble should consist of down rod blades, shackle canopies etc and with double ball bearing system. (BEE 5 Star rated - 1200/900 sweep) including all labour, material, t&p as per direction of Engineer-in-Charge.

Supply of 300mm sweep Exhaust Fan including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying and fixing 3 pin, 5A ceiling rose on the existing junction box/ wooden block including connections etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying and fixing brass batten/angle holder including connection etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Installation, Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge. [i] Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge. [i] Single pole

[ii] Single pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. including all labour, material, t&p as per direction of Engineer-in-Charge. 50 sq. mm 3-1/2 core

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. including all labour, material, t&p as per direction of Engineer-in-Charge. Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Supply and burying of 600mmx600 mmx6mm G.I. plate, vertically for earthing with its top atleast 3 mts. below ground level complete with 20mm G.I.pipe and funnel for watering and two earthing leads of No.8to10SWG G.I.wire in 15mm diaG.I. pipe upto switch board (from apron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm. square C.I. frame with hinged cover, masonary housing, alternate layers/of charcoal/ coke and salt at least 150mm thick alround etc. complete in all respects including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying & Laying of 25mmx3mm G.I. Strip for earthing purpose as required complete in all respects including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required including all labour, material, t&p as per direction of Engineer-in-Charge.

Supply and fixing of 12 Watt to 15 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing with extended heat sink, diffuser of Polycarbonate material and driver set complete in all respect. CAT-AAA including all labour, material, t&p as per direction of Engineer-in-Charge.

Supplying and fixing of 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including all labour, material, t&p as per direction of Engineer-in-Charge. MCB 63 Amp. Three Pole 10kA

MCB 40 Amp. FP 10kA

Construction of Boundary Wall super structure height 1.8m & railing height 0.45m Including Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drain,Providing and laying in cement concrete 1:4:8 ,R.C.C. work in Beam M-20 (1:1.5:3), R.C.C. work in Column M-20 (1:1.5:3), R.C.C. work in Footing(Raft Foundation) stone ballast. ( 1:1.5:3 ) M-20, M. S. work in R.C.C. Beam,column&Footing TMT Fe-500, Brick work with common burnt clay (non modular) bricks of class -150 in foundation (1 cement : 6 coarse sand ), Brick work in super-structure (1 cement : 4 coarse sand) and bitumen painting by VG-10 bitumen on DPC, including 12mm thick plaster (1 cement : 6 coarse sand), finishing walls with acrylic smooth exterior paint two or more coats @ 1.43 ltr/10sqm over and including priming coats exterior primer @ 2.20kg / 10sqm i/c centering &shuttering including strutting, propping etc. and removal of form work for all heights and all RCC work, i/c hire and running charges of all equipments, tools, plants and machinery and labour materials required for the job complete in all respect of work as per approved drawing and as per direction of engineer-in-charge.

Construction of M.s. Gate size [4.5m wide & 2.0m height] including earth work in excavation i/c laying cement concrete 1:4:8 & RCC work M-20 grade in beam and columns, including steel work welded in built up sections / framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer @ 0.90 litre/10 sqm using structural steel etc, steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500 D & 12 mm thickcement plaster (1 cement : 6 coarse sand), i/c painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade of two or more coats @ 1.67 ltr/10 sqm to achieve smooth surface i/c hire and running charges of all equipments, tools, plants and machinery and labour materials required for the job complete in all respect of work as per direction of engineer-in-charge.

Construction of Septic Tank size [4.30m X 1.20m X 1.95m] & Soak Pit [1.80m dia] including earth work in excavation and laying cement concrete (1:4:8) over cement concrete (1:2:4), including M-20 R.C.C. work in slab, brick work in foundation (1:4), steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500 D, including 12mm plaster (1:3) with floating coat of neat cement, 25mm thick C.C. M-15 (1:2:4) flooring, 40mm gauge brick ballast, including fixing of soil waste and vent pipes 75mm dia, i/c m.s. foot restsfixing in manholes with 20x20x10cm cement concrete blocks 1:3:6, including pre-cast R.C.C. manhole cover 450mm dia, including pre-cast R.C.C. manhole cover 500mm dia, including centering & shuttering including all material, labour, tools and plants in all respect to complete work as per approved drawing and as per direction of Engineer-in-Charge.

Construction of Rain Water Harvesting Pit size [3.00m X 2.00m X 3.60m] including earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains all kinds of soil from 0.00 mt to 3.00 mt depth or its parts, including cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) i/c form work, including M-20 RCC Slab, brick work with common burnt clay class 150 in (1 cement : 4 coarse sand), steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory TMT Fe-500, 15mm cement plaster in single coat on rough side of single or half brick wall finished with a floating coat of neat cement (1 cement : 4 coarse sand), cement concrete flooring (1 cement : 2 coarse sand : 4 graded stone aggregate), Supply & Laying of 40 mm gauge over burnt brick ballast for filter pit area, including M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 in position pre-cast R.C.C. manhole cover and frame of Circular shape 500 mm internal of approved quality, includingcentering and shuttering including boring/drilling borewell of required data for casing/strainer pipe by suitable method beyond 90m and up to 150m depth below ground level of 300mm dia borehole including supplying assembling, lowering and fixing in vertical position in borewell unplasticized PVC medium well screen pipes with ribs conforming to IS:1:28.8 and IS :2800 (Part-1) with gravel packing in tube well in accordance with IS:4097 including providing gravel fine/medium/coarse in required grading and sizes as per actual requirement including drainage work pipes 80mm to 300mm dia meter of NP-2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar (1 cement : 2 fine sand) i/c tasting of joint etc. and providing and laying cement concrete (1:5:10) upto the haunches of 150mm dia RCC Pipe i/c bed concrete as per standard design and constructing masonrychamber 60x60x75cm inside as per approved drawing supplied by the deptt. during the execution of work and specifications provided by the deptt. i/c hire and running charges of all equipment's, tools, plants and machinery and labour materials required for the job complete in all respect of work as per direction of engineer-in-charge. Centering & shuttering including strutting, propping etc. and removal of form for slab,Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method, beyond 90 metre & upto 150 metre depth below ground level. Drilling of 300mm dia bore hole manually., Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs 150mm Nominal dia. Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms up to 1.50 m depth, Pipes 80 mm to 300 mm diameter, Providing and laying Non pressure NP2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortarin the proportion of 1:2,Providing and laying cement concrete 1:5:10, Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom dia and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix stone agg. 20mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 stone agg. 40 mm nominal size) and inside plastering with cement mortar 1:3 ,12 mm thick including all labour, material, t&p as per direction of Engineer-in-Charge.

Construction of Interlocking road size 4.96meter wide including earth work in excavation in trenches for foundations, pipes, cable etc. in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 50 meter, including preparation of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site (Size range 53 mm to 0.075 mm) having CBR Value-25, M-150 brick work in 1:4, including cement concrete 1:2:4, including sand filling in plinth and floors, including watering, ramming, consolidating and dressing complete & laying factory made chamfered edge cement concrete paver blocks of required strength, thickness & size and shape, made by table vibratory method using PU mould, laid in required colour& pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, including all material, labour, tools and plants in all respect to complete work as per approved drawing and as per direction of Engineer-in-Charge.

M/S S.P CONSTRUCTION

M/S ARVIND KUMAR DUBEY

M/s PARI ENTERPRISES