Construction of Tin Shed work for Shri Annpurna Rasoi near Jhalarbawari Bapparawal chouraha at Nagar Palika area

Earth work in excavation for roadway, including trimming bottom and side slopes in accordance with requirement of line, grades and cross sections, including disposal of surplus material with all lift and lead upto 1000 metre as per MoRT&H specification clause 301. In all type of soil.

Providing and laying lean cement concrete 1:4:8 in Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in concrete mixer, laid manually, compacted with surface vibrator, finishing and curing complete as per clause 601, 112 of MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of diversion.

Random Rubble stone masonry work in cement mortar with mechanical mixer in foundation (at any level) complete as per drawing and technical specification and as per clause 1000 and 1400 of MoRT&H specification including all scaffolding material, labour, machinery but excluding pointing and plastering. In cement mortar 1:4 (1 cement : 4 coarse sand)

Random rubble dry stone Kharanja (soling) under floor.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275gm/m²

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Brick work with FPS bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 20 mm cement plaster of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:4 (1 cement : 4 fine/ coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Wiring of light point/fan point/exhaust fan point/call bell point with 1.5sq.mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1kV grade and 1.5sq.mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1kV grade (IS:694) in recessed ISI marked MMS (IS:9537P-III) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, roundtiles, 1.2mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3pin ceiling rose/Holder/3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/Wiring accessories refer Chapter E-04, E-05 & E-07F or additional technical parameters of product/work refer Annexure 'A' attached with this BSR

Medium point (up to 6 mtr.)

Long point (up to 10 mtr.)

Providing & Fixing of 1200mm sweep BLDC technology power saving ceiling fan which can with stand on voltage fluctuations from 140 volts to 240 volts, power factor not less then 0.9, service value (CMM/W) minimum 6.85, air delivery minimum 220CMM, speed minimum 330 RPM (tolerance as per IS:3742019) THD less then 10% and complete with down rod of 15mm dia. ERW (Electrical resistance welded) of 1.6mm nominal thick medium duty steel pipe up to 80cm, cotter pin with 3×1.5sq.mm pvc insulated flexible copper conduct or making connection testing etc. as required. All as per pre approved by Engineer-in-charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR without Remote

Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer-in-charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR. 450 mm sweep (900/1400 RPM)

Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%, P. F. ≥ 0.95, CRI >80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. 1170mm (±10%) LED batten with min. lumen output 2200 lm

Please Enable Macros to View BoQ information