BWN/Rs.109.33 Lacs/Accessible India campaign in A plus B plus C Block , ADR Center, E- disha Centre , ADC office in mini sectt. at Bhiwani

Amount

[10.1]Providing and laying of base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling.

[10.100.2]Cement Concrete 1:8:16 Flooring 2. Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth.

[10.58]Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

[10.59]Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

[11.4.2]10 mm thick cement plaster 2. 1:3 (1 cement: 3 fine sand)

[11.5.4]12 mm cement plaster of mix : 4. 1:6 (1 cement: 6 fine sand)

[11.6.2]15 mm cement plaster on the rough side of single or half brick wall of mix : 2. 1:6 (1 cement: 6 fine sand)

[11.64.1]Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1. New work (two or more coats) over and including water thinnable priming coat with cement primer

[11.69.1]Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 1. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

[11.71.1]Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade : 1. Two or more coats on new work

[12.108.1]Providing fixing aluminium round shape handle of outer dia 100mm with screws etc. complete. 1. Anodized (AC-15) Aluminium

[12.157.1.1]Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 1.1. For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

[12.21.1]Providing and fixing factory made shutters of Pre-laminated particle board flat pressed three layer or graded wood particle board with one side decorative finish and other side balancing lamination conforming to IS: 12823 Grade l Type ll, of approved design, and edges sealed with water resistant paint and lipped with aluminium `U` type edge beading all- round the shutter, including fixing with angle cleat, grip strip, cadmium plated steel screws, including fixing of aluminium hinges 100x63x4 mm etc. complete as per architectural drawing and direction of Engineer-in-Charge (Cost of `U` beading and hinges will be paid separately). 1. 25 mm thick

[13.41]Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

[17.6]Construction of Embankment with Material obtained from Borrow pits NA Construction of Embankment CBR 8% (for new road/ raising/ berms/ etc.) with approved material obtained from borrow pits, including compensation of earth with all lead and lift transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2, as per technical clause 305 of MORT&H specifications.

[20.20.2.1]Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading 2.1. Including cost of specials 15 mm internal diametre of pipeline

[20.20.2.2]Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading 2.2. Including cost of specials 20 mm internal diametre of pipeline

[20.23.1]Extra for fixing and jointing union couplings in G.I. and W.I. pipelines. 1. 15 mm internal diameter

[20.23.2]Extra for fixing and jointing union couplings in G.I. and W.I. pipelines. 2. 20 mm internal diameter

[20.25.1]Cutting holes up to 23 cm square through brick work in mud walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 1. 11.43 cm thick wall

[20.31.2]Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I. pipelines laid in the ground or inside buildings, including cartage from divisional stores or nearest railway station to site of works. 2. 20 mm internal diametre

[21.84.1]Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement R.C.C. 1:2:4 slab 100 mm thick/cement concrete topping, 50mm thick with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chamber cover and frame weight as per I.S.I. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. 1. Size 450 mm X450 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with C.C. topping

[22.104.1]Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 1. 15 mm nominal bore

[22.107.1]Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1. 15 mm nominal bore

[22.127]Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

[22.181]Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

[22.209]Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

[22.23.1]Providing and fixing white vitreous chinaware pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 1. W.C. pan with ISI marked white solid plastic seat and lid

[22.24.1]Providing and fixing white vitreous chinaware pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chinaware flushing cistern and C.P. flush bend with fittings and C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 1. W.C. pan with ISI marked white solid plastic seat and lid

[22.32.1]Providing and fixing vitreous chinaware dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat and lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: 1. White vitreous chinaware dual purpose WC pan with white solid plastic seat and lid with white vitreous chinaware flushing cistern and C.P. flush bend.

[22.36.3]Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : 3. Coloured (other than black & white) solid plastic seat with lid

[22.88.1]Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 1. 15 mm dia nominal bore

[22.88.2]Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 2. 20 mm dia nominal bore

[23.11]Making suitable hole in the wall suitable for exhaust fan up to 450 mm sweep including finishing the same and fixing of Stainless steel wire mesh 2 mm thick having about 50 meshes per inch at exhaust side complete as required

[23.12]Providing and fixing outdoor duty Ply of 12 mm thick frame suitable for exhaust fan up to 450 mm sweep etc complete as required

[23.3.1.3]COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS) 1.3. Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group C

[23.9]Erection of exhaust fan in existing opening ,complete with necessary earthling of fan including carriage from PWD store to the site of work.

[34.26]Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including Reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

[4.14.1]Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil.

[4.33]Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

[5.23.2]Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 2. Nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

[6.1.1]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1. 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

[6.1.2]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 2. 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

[6.1.4]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 4. 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

[6.1.7]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 7. 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size)

[6.33.3]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level 3. Cold twisted bars

[6.8.2]Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 2. 40mm thick

[7.20.2]Brick work with common burnt clay modular bricks of class designation 10.5 in foundation and plinth in: 2. Cement Mortar 1:6 (1 cement : 6 coarse sand).

[7.22.2]Brick work with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : 2. Cement mortar 1:6 (1 cement : 6 coarse sand)

[8.25.1]Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete : 1. 12 mm thick

[9.11.1]10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: 1. With common burnt clay non-modular brick tile of class designation 10

[9.17.1]Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 1. In 75x75 mm deep chase

[9.18]Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

[9.57.3]Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 3. 150 mm diameter

[9.58.5.3]Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 5.3. Bend 87.5° 150 mm bend

Providing and fixing coloured self addhesive PU tactlie tile ground surface indicators (made of polyorethance) of size 300mmx300mm for guiding/dirction/warning to the visuality impoaruied visitors in the centre/side of the pedstrain/ approach pathway as per design/specificaion and a guidelines complete in all respec to the eniure satisfaction of Engineer-in-charge(N.S.)

Providing and fixing coloured ceremic (tectile), tile ground surface indicators of size 300x300mm of approved make for guiding/direction/warning to the visually impaird visitor in the cenre/side of the pedstrain/approach pathway as specified oe base of 20mm thick cement coarse sand mortar 1:3 and jointd with white cement slurry mixed with pigment to mach the shade to tiles as per design/ specificiation and guidelines complete in all respec to the eniure satisfaction of Engineer-in-charge(N.S.) NOTE: the tile shall be premium quality (Ist Qualiuty) of reputed manuacturer like NITCO,Kajaria,SOMANI, ORIENT and JONHONSONS (NS)

Providing and fixing acrylic Braille indicators of size 170mmx35mm for handrails of the approved design and make having Braille dots raised 0.5mm above base plts to be isntalled at the specified locatioons a pedr directions of the engineerin-chage complete as per design/specifications and guidelines as per entire satisfaction of the Engineer-in-Chage(N.S.)

Proiding and fixing 50mm wiode colour contract EDGE STRIPS sef addhesive on treads of stair cases to held people with visual disbilities and elederly even indim light condition complete in all respect to the entire satisfaction of the Engineer-in-Charge (N.S.)

Proiding and fixing of high intensity reflective conspiculty tape 25 to 50mm width onedges of treads in stairccase including cutting passing etc. of make 3 M of equivalent brand complete in all respect to the entire satisfaction of the Engineer-in-Charge (N.S.)

Providing and fixing retro reflective information SIGNADES to provide clear information about the building/institute in English/Hindi languages clearly visible readable understandable property lit at night and appropriate level, made of 4mm thick ACP sheet with border of 50mm dia round pipe and supports with 200mm dia round pipes of 10 guage fixed in the gate pillars properly designed M-20 grade cement concrete completion all respect as per design/ specifications and guidelines as per entuire satisfaction of the Engineer-in-charge (Size 6 Mtrx 1.2 Mtr) (N.s.)

Providing and fixing of acrylic non glare, tactile audio pictorial building layout as per the approved size design and make having 6mm thick acrylic non glare base of the approved colour and non glare acrylic cut out symbols and upper case sans serif leters of 12mm height raised 3mm above base plats and grade 2/ grade 1 Braille to be integral with the sign face and be raised 0.5mm above base plats. the mape to be installed at the specified location as pe accessibility standards shall be orients to the position of the iewers and to be insalled at a height of 800mm from the finioshed ground/floor level and using the necesry hardware spified by the manufacturer and to be installed upto the height of 800mm from the finished ground/floor leel and using the necesary hardware specified by the manufacturer and to be installed complete as per design/ specifications and guidelines as per the entire satisfaction of the Engineer-in-Charge (N.s.)

Providing and fixing of SS non glare multilingual Braille (raised dots) ENTRANCE SIGNAGE (size 1 ft x1 ft) as per approved design and make idicating the ame of the building having 1.2mm thick SS non glare blue coloured bae plate with the Universal Accessibility Symbol and Upper case sans serif words of ehgith 15mm engraved on i along with the equivalent ward/s written in Hindi using Devanagari scrupt of height 15mm in white colour grade 2/grade 1 Braille to be etched engraved and be raised 0.5mm above base plates. The signage to be installed at the specified location on the compound wall nea the site entrance gate installed at a height of 1200 mm from the finished ground/floor level and using the necesary hardware specified by the manufacturer and to be installed complete as per design/ specifications and guidelines as per the entire satisfaction of the Engineer-in-Charge (N.s.)

Providing and fixing Multilingual and tactile emerency ecacution map of each floor indicating the current position of the viewer saying YOU ARE HERE of 15mm height letters in red with white background indicating the emergency exists, locations of the existing uishers etc. signs shall have a solid header with the text `EVACUATION PLAN` in contrasting uppercase letters no less than 3/4` in height . The size of the board shall be 2 ft x2ft and shall be installed at a height of 1200mm from FFL and shall be oriented to the position of the viewer as per the direction o fthe site engineer complete as per design/ specifications and guidelines as per the entire satisfication of the Engineer-in-Charge (N.S)

Providing and fixing acrylic multiligual Braille (raised dots) DIRECTIONAL SIGNBOARDS of size 6`x9` designed as per accessibility standards and having 4mm thick acrylic base plates with Upper case san serif words made of white acrylic non glare ut out letters of height 15mm raised not less than 0.8mm above base plate and having a non-glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufactured specifications on wall at the approved location and at a height of 1200mm from FFL complete as per design/specification and guidelines as per the entire satisfaction of the Eingineer-in-charge (N.S)

providing and fixing acrylic multilingual braille (raised dots) signboard (DOOR SIGNBOARD) of size 6`x9` for rooms tiles, designed as per the Drawings issued and having 4mm thick blue acrylic base plate with upper case San serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and equivalent word written in Hindi with Devanagari non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate. Grade 2/ Grade 1 Braille to be integral with the sign face and be raised 0.5mm above base plate. Each signboard to be fixed as per manufactures specifications on the wall adjoining the respective room door at a height of 1200mm from FFL complete as per design / specifications and guidelines as per the entire satisfaction of the Engineer-in-charge (N.S)

Providing and fixing of SS, non-glare signage board (2 ft. x 2 ft. - 1No.) for the accessible parking, as per the approved design and make, having 1.2mm thick SS non glare base plate and grade 2/ Grade 1 Braille (raised dots) to be etched/engraved and be raised 0.5mm above base plate and upper Case San serif words and univesal Accessbility Symbol to be etched/engraved and signage to be installed at aheight of 2100mm from the Ground level using a post of MS hollow square section (50mm x 50mm) as per the installation procedurespecified by the manufactrer and as per accessibility standard as per the entire satisfaction of the Enginner-in-charge (N.S)

Providing and fixing `U` shaped `flip Bar` 650mm long and 30mm - 40mm thick diameter of 18-gauge with hinge made up of stainless steel of international standard in the toilet to make them `unisex toilet` for visually impired visitors as per design / specification and guidelines complete in all respect to the entire specification of Engineer-in-charge (N.S)

Providing and fixing `L` shaped `Grab Bar` 650mm long and 30mm - 40mm thick diameter of 18-gauge with hinge made up of stainless steel of international standard in the toilet to make them `unisex toilet` for visually impired visitors as per design / specification and guidelines complete in all respect to the entire specification of Engineer-in-charge (N.S)

Providing and fixing `U` shaped `Flip Bar` 650mm long and 30mm-40mm thick diameter of 18-gauge with hinge made up of `stainless steel` of International Standard in the toilets to make them `Unisex Toilet` for visually impaired visitors as per design / specification and guidelines complete in all respect to the entire satisfaction of Engineer-in-charge (NS)

Providing and fixing `L` shaped `Grab Bar` 600mm long and 30mm-40mm thick diameter of 18-gauge made up of `stainless steel` of International Standard in the toilets to make them `Unisex Toilet` for visually impaired visitors as per design / specification and guidelines complete in all respect to the entire satisfaction of Engineer-in-charge (NS)

M/s Hisar Construction Company