ADDN/ALTN AND SPECIAL REPAIR TO BLDG NO P-07 POLO ROAD AND 03 NOS MINOR WORK FOR COVERED SHED NEAR GIRLS HOSTEL DGNCC CAMP, BLDG NO P-16 MALL ROAD AND BLDG NO P-42/02 URBAN VILLAGE

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n.exc 4 sqm each and removing to store complete all as specified and as directed.

Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) and 8mm thick tinted/frausted glass. (Note: The unit rate quoted by contractor include cost of glass and all other connected accessories. Net opening including frame will be measured for payment purpose.) Make:-Okotech Aparno, H20 Solution, Fenesta or equivalent

Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) and with stainless steel wiremesh (0.36mm nominal dia of wire and average width of apreture 1.40mm. (Note: The unit rate quoted by contractor include cost of wiremesh and all other connected accessories. Net opening including frame will be measured for payment purpose.) Make:-Okotech Aparno, H20 Solution, Fenesta or equivalent

Aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double revated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed.

Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty “SAMRAT” , locking arrangement “GODREJ”, rubber gasket and door stopper complete all as specified and as directed.

S & F for 1st class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed

S & F for Factory made door shutter 35mm thick 1st class hard wood for plain framed panelled shutters (any number of panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS: 1003(Part 1), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S & F for Factory made window with side hung shutters with glazing beads, shutter 35mm thick 1st class hard wood for plain framed panelled shutters (any number of panels)of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per SSR Part I, Section 8 clause 8.24(b), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S & F for Factory made window with side hung shutters without glazing beads, shutter 35mm thick 1st class hard wood for plain framed panelled shutters (any number of panels)of 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per SSR Part I, Section 8 clause 8.24(b), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S & F 35mm thick 1st class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. devided into squres with sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples include for fixing with beads.

S & F 5.5mm thick tinted glass sheet glass glazing with oil putty in squares n exc 0.5sqm in each panes complete all as specified and as directed.

Preparation of new wooden surface and applying polish for a glossy finish over 10cm width or girth, complete all as specified and as directed.

S & F 150mm size brass butt hinges complete all as specified.

S & F 150 mm long brass barrel tower bolt, fixed complete all as specified and directed.

S&F 300 mm long brass coated sliding door bolts, plate type, stove enamelled black, with brigh bolt not less than 12 dia with and incluidng 1 minimum of 6 bolts and nuts four or bolt plate and tow on staple plate complete all as specified.

S & F 150 mm long brass handle oval type, complete all as specified and as directed.

M & L for Vitrified coloured ceramic tiles light shade 10mm thick, square/rectangular(with pattern and boarder work as required at site), area of tiles exceeding 0.42Sqm and not exceeding 1.0Sqm each tiles as in flooring over and including 15mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match over or filling spacers as per requirement at site or as directed by Engr-in-Charge or GE, including dismantling of old tiles with cement mortar bedding but not backing complete all as specified and as directed.

M & L for Vitrified coloured ceramic tiles light shade 10mm thick (square/rectangular) polished, as in skirting/dados on vertical surfae of walls etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 including dismantling of old tiles with cement mortar bedding but not backing complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for glazed coloured ceramic tiles in vertical surface 300x600x7 mm thick (with pattern and border work as required at site) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick rendering in CM 1:4 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M & L Vetrified tiles (square/ rectangular) of size 600 x 600 x 10 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including cement screed bed 15mm thick in cement mortar 1:6,including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M&L Wooden interlocking floor tiles 1215mm x 168mm x 8mm thick rectangular tiles fixed in floor/dado over existing floor with foam sheet of best quality including jointing/end covering strip including all other fixing materials, including taking down existing wooden flooring of any type complete all as specified and as directed. (Make kajaria catlog No AC 3 or equivalent in Somany/Cera).

Taking down cement or cement lime plaster , any description on brick or stone walls or from ceilings etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces and finished even and smooth without using extra cement in any position incl scaffolding etc, complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement in any position incl scaffolding etc, complete all as specified.

M & L rendering 10 mm thick on concrete surfaces as in ceiling in CM 1:3, finished even and smooth without using extra cement including complete all as specified and as directed.

M& L for screed bed 15mm thick on top of cleaned concrete surfaces in cement mortar 1:4 mixed with water proofing compound, including taking down existing roof treatment of any type and also taking down cement plaster on concrete surfaces, including raking out joints, hacking for key, scrubbing down with water etc., to receive further treatment, complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately under respective item.

Supply only water proofing compound, to be mixed in cement mortar or concrete as per proportion specified by manufacturer, complete all as specified and as directed.

Providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Make: SmartCare Damp Proof of Asian Paints or equivalent in Berger and Nerolac. Notes: (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the ter proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M & L 20 mm thick granite of any type work table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in over and incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching and moulding complete all as specified and as directed .

M & L for Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radious built in CM 1:6 including demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified.

S & F tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F tubing 25mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F in repairs 25mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

S & F Rotational moulded polyethylene water storage tanks 2000 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete all as specified and as directed.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavatged matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

Excavation in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning, filling in ramming earth or broken rubble in layers not exceeding 25 cm, watering and removing of surplus soil to a distance not exc 50m and making good surfaces, complete all as specified and as directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and similar work; vertical or to batter complete all as specified and directed.

M & L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular rough finished surfaces of concrete laid flat complete all as directed.

M & L for form work to soffits of suspended slabs such as roof slabs, floor, slabs landings and stair and similar work not exc. 20 cm thick flat rough to receive plaster all as specified and directed.

M & L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete.

M & L for mild steel TMT bar 10mm dia and over cut to length,bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All same as per srl item No 51 above but 8mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M & L for RCC 1:1.5:3 using 20mm graded agg as in footings, plinth beam and bases of columns complete all as specified and as directed.

M & L for RCC 1:1.5:3 using 20mm graded agg as in columns , piers posts and struts complete all as specified and as directed.

M & L for RCC 1:1.5:3 using 20mm graded agg as in slabs, supported on walls, landings, balconies and in shelves and the like complete all as specified and as directed.

S & F for Mild Steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed

Demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished even and smooth without using extra cement including demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed

S & F painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F painted galvalume aluminum zinc coating GI based corrugated steel (Curvical Shape) sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F 2mm thick fibre glass reinforced translucent Plain/corrugated sheeting with additional reinforcement of chicken mess with two corrugation side lap fixed with 'L' or 'J' type or crancked hook bolts complete all as specified and directed.

M&L for galzed cooured ceramic tiles in vertical surface area of each tile exc 0.18 Sqm but not exc 1.18 Sqm (with pattern and border work as required at site) set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick rendering in CM1:4 incl dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for Coloured Chequered cement concrete tiles 25cm x 25cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over and incl 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) confirming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid dry in floor/path complete all as specified and as directed.

S & F in repairs 15mm bore Angle valve of CP high pressure screwed for iron pipe and fixed complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs Two way Angle valve 15mm bore dia or pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repair 15mm bore, fancy type CP bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified. (Make: Jaquar/Marc/Kohler)

S & F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S& F in repair Brass chromium plated towel rack of size 600 mm x 350mm, fixed with brass screws, fixed in repairs, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F Stainless steel Grating dome 125mm dia with or without hole for waste pipe, fixed in repairs, complete all as specified and as directed.

S & F in repairs CP toilet paper holder fixed with plug and brass screws, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs Brass CP basin mixer central hole, for mixing hot and cold water fixed as per manufacture's manual, with long shunk and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. KUP-35051BPM, Jaquar-Cat No. KUP-35005BPM, Kohler-Cat No. K-74013IN-4BND-CP, Kohler-Cat No. K-74026IN-4BND-CP.

S & F in repairs Brass chromium plated wall mixture 3 in 1 system with provision for hand shower and overhead shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls, fixed in repairs, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. CON-281KN, Jaquar-Cat No. COP-281PM Kohler-Cat No. K-98754IN-4-CP.

S & F in repairs Vitreous china floor mounted WC ( Cascade) one piece type (off white) including connecetion in drain etc incl water closet seat cover CP jet spary, Health Faucet, flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed. (Make : Jaquar or equivalent in Cera/Parryware).

S & F in repairs Vitreous chinaware table top wash hand basin (WHB) of size 595mm x 440mm x 185mm complete including 32 mm dia chromium plated waste coupling, complete all as specified and as directed. (Make : Jaquar Cat Part No. KUS-WHT-35901 or equivalent in Somany/Cera/Hindware).

S & F in repairs PVC (SWR) Floor/Nahani trap, plain dia of outlet 125mm, complete all as specified and as directed.

S & F in repairs 100mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or fixed to wall or in floors complete all as specified and as directed.

S & F 100mm dia Cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S & F 100mm dia Cast iro Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

S & F in repairs 100mm dia cast iron cowls complete all as specified and as directed.

S & F 100mm dia Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position including taking down sanitary pipes, eaves gutters and rain water pipes (any size or pattern), in any type and position including all fittings,heads,shoes, bends, swan-necks, branch pieces, couplers, reducers, vent cowl, stack clamps etc. complete all as specified and directed.

S & F 110mm bore PVC (SWR) bends any radius complete

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of wall and ceiling including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying two coats of Oil bound distemper including 2mm thick wall care putty JK or Birla complete all as specified and directed.

M & L for preparation of Old plaster external wall and ceiling surfaces by completely removal of existing painting surfaces, filling the cracks, holes with POP/Putty and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including priming coat of exterior primer applied 2mm thick wall care putty in two layers complete all as specified and as directed.

M & L for Preparation of old painted steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including priming coat of exterior primer applied and 1mm thick wall care putty over new surfaces complete all as specified and as directed.

M & L Preparation of newly plastered /unplastered surfaces of walls and ceilings over 1mm thick Birla White/J K White wall care putty, again sand papering thus making surface good and applying Two coats of Oil Bound Distemper on wall surfaces over a coat of primer ,complete all as specified and directed.

M & L two coat of synthetic enamel paint (finishing coat) over one coat of primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

M & L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

M & L for Hard core of gauge exc 63mm but not exc 100mm(broken bricks) deposited spread and leveling in layers n exc 15cm thick watred and raming to a true surface complete all as specified and directed.

M & L for brick work in CM 1:6 using Sub class "B" bricks straight or curved on plan exc. 6mmean radius complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for glazed coloured ceramic tiles in vertical surface 300x600x7 mm thick (with pattern and border work as required at site) set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M & L 20 mm thick granite of any type work table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in over 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching and moulding complete all as specified and as directed .

M&L Machine cut kota stone slab flooring 20-25mm thick over 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

S & F 20 mm bore tubes medium grade galvanised with all fitting and fixed complete to wall and ceilings or laid in floor.

S&F 15mm bore tubes medium grade galvanised with all fitting and fixed complete to wall and ceilings or laid in floor.

S & F 2000 ltr capacity rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia brass float valve complete all as specified.

S&F bib tap fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe, 15mm dia, fancy type, cast copper alloy, chromium plated long body with flange complete all as specified.

S & F framed work such as in door frame, door shutters / gate of angel or other section with gusset plates, rails, braces, etc complete , drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings, including hings hold fast of Fe 410-W (Gde E-250 quality) etc complete all as specified.

S & F Mild steel, plain, black sheet 1.60mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S & F 300mm long Mild steel sliding door bolt with haps, stapple ( bolt type ) and fixing clips of sheet, cast of extraded sections and fixing bolts and sliding bolts of extraded sections complete.

S & F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S & F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars complete all as specified.

S & F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5sqm in each panes

S & F Mild steel framed work as in grills, gratings etc, with end of bars shouldered and or riveted forged into spikes, framed guard bars, barred iron doors, ladder, framed balusters, railing, frame work for water tanks and similar works, complete conforming to Fe 290 Gde E-165, complete all as specified and directed.

Aluminium alloy powder coated standard hollow section for ventilotors as per approved sample and as per IS specifications, shutters weighting 0.55 kg/RM, rectangular frames of section 101.6mm x 44.45mm x 3.18mm weighing not less than 2.54Kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings, including aluminum powder coated grills complete all as specified and as directed.

S & F PVC (SWR) Floor/Nahani trap, plain dia of outlet 125mm, complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position complete all as specified and directed.

S&F wall mounter multiple function shower panel incl all fittings and fixture as per product code make Jaquar/Hindware description below:- (a) Item Product Code- 511686 (Size-1650mm x 150mm x 550mm) Make- Hindware. (b) Item Product Code- JPL-SSF-ST88148B (Size-1600mm x 200mm) Make- Jaquar. (c) Item Product Code- JPL-WHT-TMCURVENEO (Size-1500mm x 230mm x) Make- Jaquar.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F 100mm size stainless steel butt hinges complete all as specified and as directed.

S & F Aluminum Anodised 150mm size barrel tower bolt complete all as specified and as directed.

S & F 150mm size aluminum anodised handles complete all as specified and as directed.

S & F for Full pedestal pattern wash hand basin, size of basin 630mm x 510mm and pedestal of 900mm long ivory colour as approved by GE including fixing waste pipe and chromium plated brass waste fitting complete all as specified and as directed.

S & F fancy type CP bib tap with crutch or butterfly handle, screwed down, screwed for iron pipe 15mm di , fancy type, cast copper alloy, chromium plated long body with flange complete all as specified (Make: Jaquar/Marc/Kohler)

S & F vitreous china pedastal pattern water closet (EWC) including flush pipe & seat cover 'P' or 'S' trap complete all as specified and directed.

S & F water closet (Squat Pattern) complete incl provn of lime concrete bedding Orissa pattern size 580 x 440mm white with integral foot rests (excluding flush pipe or flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor as directed .

S & F CP shower rose fancy type 150mm x 150mm size with 600mm long shower arm fixed to 15mm bore pipe, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket and flush pipe etc complete all as specified and directed (Make: Jaquar/Marc/Kohler)

Fabrication & fixing of Modular wardrobe/ cupboard made out of 18-20 mm thick HDHMR boards with 2.00mm thick fabric colour laminate sheet of approved quality and texture on all exposed sides with edge band including providing cabinet for keeping baskets/ drawers etc. complete all as specified and as directed. (Design and pattern as approved by GE). (Make : Rajshree or equivalent)

S & F for 18-20mm thick HDHMR boards with laminated fabric colour on both sides, fixing in partitions of Modular kitchen cabinet & wardrobe/ cupboard complete all as specified and as dirfected. (Make : Rajshree or equivalent)

S & F for Fancy type Stainless steel bright polished handles oval type of size 150mm size, complete all as specified and as directed.

S & F for Hettich soft closure hinges of premium quality, fixed in door/cup board shutters complete all as specified and as directed

S & F Prelaminated particle board 18/19 mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination as in kitchen cabinets/shutters fixed with screws to timber framework all as specified and directed.

S & F Continuous (piano) hinges, Mild Steel, bright finish or electrogalvanised (width of flap 40mm when open) complete all as specified and as directed.

Supply only Stainless steel Cutlary basket of size 500mm x 370mm x 100mm made of 4mm th S.S.wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers as approved by Engr-in-Charge.

Supply only Stainless steel basket (plain) of size 500mm x 370mm x 160mm made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers as approved by Engr-in-Charge.

Supply only Stainless steel bottle full out of size 500mm x 400mm x 160mm in two tier made of 4mm th S.S.wire approved quality with suitable arrangement for fixing Telescope basket (channel) 18'/20' length two way extruded MS galvanised over rollers as approved by Engr-in-Charge.

M & L 20 mm thick granite (Z black colour) of any type work table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in over and incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching and moulding including demolition of existing granite complete all as specified and as directed .

S & F in repairs Fancy type sink mixer for mixing hot and cold water with swinging port, screwed for iron pipe,15mm bore complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repair Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap with connection to drain and to flushing pipe antisyphonage pipe, and making good to floor complete all as specified and directed.

Taking up or down 15mm steel tubing and connections including fittings complete all as specified.

Taking down shutters of any description not exceeding 2.00 Sqm each complete all specified and directed.

S & F for flush shutters 40 mm thick solid core constructions with block boardcore , ply wood face panels commercial type on both side complete all as specified and as directed.

S & F 35mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. devided into squres with sash bars, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S & F Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperature 1.4mm and fixed to doors and widows with necessary 12mm iron flats with welding and including dismantling of old wire cloth complete all as specified and directed.

M & L for preparation of new wooden surfaces & applying 2 coats of synthetic enemel paint over a coat of wood primer complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, removing materials to store for keeping for taking credit and making good disturbed surfaces of complete all as directed.

Taking down LED tube light fitting, Wall light fittings, bed light fittings etc. removing materials to store for keeping in safe custody and then refixing in position after repair work complete all as directed.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked and including PVC concealed conduit ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends, elbow, reducers etc including FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl MS Box/ Metal flush box and 3mm thick hylem sheet/ cover plate of suitable sizes for fixing modular switches/sockets/fan regulator etc , complete all as directed.

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

One socket outlet point 15 amps on the independent board. with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire complete.

Additional light fitting wiring with 1.5 sqmm copper conductor cable on the same circuit ( 3 runs considered as one run)

S&F in replacement of Modular switch 6 Amp, 1 way, 1 module size complete all as directed.

S&F in replacement of Modular socket 6 Amp, 2/3 pin, universal type, 2 module size complete all as directed.

S&F in replacement of Modular switch 16 Amp, 1 way, 1 module size with indicator lamp complete all as directed.

S&F in replacement of Modular socket 16 Amp multipurpose shuttered type, 2 module size complete all as directed.

S&F in replacement of Modular Fan regulator step type, 120 watts, 2 Module size complete all as directed.

S&F in replacement of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

Supply and fixing in replacement of of LED tube light fitting 20 W wall mounting type with and including all electric connections complete all as specified.

Supply and fixing in replacement of of LED mirror light fitting 10 watt, cool/warm white and making all electric connections complete all as directed.

S&F in replacement of LED bed side light, 5/6 Watts, wall mounted type and making all electric connections complete all as specified and as directed.

S&F of LED ceiling light fitting 15 watt, in round shape, surface/recess type cool/warm white with inbuilt driver and making all electric connections, complete all as specified and as directed.

S&F of LED ceiling light fitting 10 watt, in round shape, surface/recess type cool/warm white with inbuilt driver and making all electric connections, complete all as specified and as directed.

S&F of Flexible LED strip light tubular type , cool/warm white , including AC to DC adapter and making all electric connections, complete all as specifed and as directed.

S&Fof AC to DC adapter suitable for tubular type LED strip light cool/warm white, complete all as specified and as directed.

S & F in replacement of energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed.

Supply and fixing in replacement of street light fitting bracket, 1.0 mtr long made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc complete all as specified and as directed.

S&F in replacement of ceiling fan of size 1200mm sweep 240V single phase, 50Hz DB, BEE, 5 Star rating compete and depositing the old u/sto MES store yard complete all as specified and as directed by Engineer in Charge.

Supply and fixing in replacement of Ventilation fan 250mm sweep,1250 RPM,non metalic resin body,air delivery > 800 CMH, 5 nnumber of blades single phase 240 volts AC 50 Hz and connecting up complete incluiding louvers and provision of copper cable 3 core of size 0.5 sqmm complete all as specified and as directed.

Supply and fixing Wall Mounted Fan 400 mm sweep plastic body type including making all electric connections complete all as directed.

S&F replacement of Geyser 25 litre capacity vertical type with steel tank and glass inner linen , 5 star rating complete including fastners (4No.) for hanging and CP and PVC connection for inlet and outlet upto stop cock including taking down the old u/s geryser and depositing to MES store yard complete all as specifed and as directed.

M&L in replacement of Sub main wiring with 2 run of 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into PVC concealed conduit 25 mm dia medium grade with all fittings and including 10.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

M&L in replacement of Sub main wiring with 2 run of 6 .0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into PVC concealed conduit 25 mm dia medium grade with all fittings and including 6.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

M&L for Sub main wiring with 2 run of 4 .0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn into PVC concealed conduit 25 mm dia medium grade with all fittings and including 4.0 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to sub main DB complete all as directed.

S&F in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 08 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

S&F in replacement of MCB SP, C Curve type, 10 KA, 10 to 32 Amp, with over load and short circuit protection complete all as directed.

S&F in replacement of MCB SPN C Curve type, 10 KA, 40 to 63 Amp, with over load and short circuit protection complete all as directed.

Supply and fixing in replacement of MCCB incommer Distribution Board ( Vertical Load line DB) double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, VTPN 04 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB as incommer and MCB as outgoing and making all necessary connections and taking out the old unserviceable DB complete all as directed.

S&F in replacement of MCCB 3P 125 Amp with breaking capacity 16 KA suitable for 415 volts AC supply, with over load and short circuit protection complete all as specified.

S&F of LED Bollard Fittings 10W suitable for pathway lights including making electric connections, complete all as specified and as directed.

S&Fof rigid non metallic PVC conduit 20mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc complete including cutting chasis in wall and making good the surface, complete all as specified and as directed.

S&F of MCB DB confirming to IP 43 - 09 with single door, SPN 02 way double door complete with din rail , Neutral and earthing bar after taking out the old u/s DBs, connection and making good the disturbed surface, complete all as specified and as directed.

S&F of aluminium cable 1100 Volt grade, served with inner sheathing of PVC tape and overall PVC sheathed twin core cable circular of size 4 Sqmm ISI marked in service connections, including taking down old unserviceble cable, complete all as specified and as directed.

S & F for switch piano, flush type single pole, one way 5 Amp complete all as directed.

S & F for switch piano, flush type single pole, one way 15 Amp complete all as directed.

S & F for of socket outlet 2 in 1, 3 pin, 5A, flush type complete all as directed.

S & F for of socket outlet 2 in 1, 3 pin, 5 and 15A, flush type complete all as directed.

S&F of step type Fan regulator , 120 watts, piano flush type complete all as directed.

Supply and fixing LED tube light fitting, 20 watt. with and including all electric connections complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic and accessories, 230 V, 1200 mm sweep with service value not less than 6.00 BEE. Five star rated with brushless direct current motor (BLDC).Complete all as specified and as directed

Supply and fixing exhaust fan upto 450 mm sweep metalic body type heavy duty industrial type and making all electric connections complete all as directed and specified.

Supply and fixing of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 8 way, 240 volts with bus bar rating 200 Amps, suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

Supply and fixing of MCB C Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection complete all as directed.

Supply and fixing of isolator 40 Amp, SPN type with over load and short circuit protection complete all as directed.

Supply and fixing LED security light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete all as directed.

Supply and fixing of security light fitting bracket, 1 mtr long made out of galvanized iron pipe of 25 mm dia size light grade bent to shape complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Material and labour of LT underground cable XLPE insulated, PVC Sheathed armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 2 core on wall with clamps,saddles etc including all connections with thimbles of suitable size, complete all as directed.

S & F LED energy efficient integrated battens fittings, PVC extruded heat sink with shatter proof opal shell of polycarbonate compound, 10 Watts, cool/warm white as per site requirement complete all as specified and directed.

Supply and fixing of Ventilating fan 200 mm sweep plastic body type including self cosing louver and making all electric connections complete all as directed.

Supply and fixing high pressure booster pump with 8 ltr capacity pressure tank, coupled with electric motor of capacity 0.98 HP, 230 volts, single phase, 50 Hz incl Pressure Guage, Pressure switch & connecting accessories of GI i.e bend, nipple, socket, tee of requisite size etc incl cutting of existing pipe complete all as directed.

M&L for sliding/openable glass door 12mm thick (toughened glass) of approved quality incl necessary all stainless steel powder coated hardware fittings (as like sliding rail, guide, clips, frame, brackets, clits, jammers, stopers, locking arrangement etc) door fixed with floor spring, with two Nos stainless steel handle on each leaf/door n exc 30 cm long 25 mm thick complete drilled for fixing with all fitting and fixture complete all as specified and as directed.

M&L for 12mm thick (toughened glass) of approved quality fixed in any position (partition, bathroom enclosure and the like) incl necessary all stainless steel hardware fittings (as like frame, brackets, clips, jammers, stoppers etc) complete drilled for fixing with all fitting and fixture, complete all as specified and as directed.

The new hut furnitures