REPAIR/MAINT OF PIPELINE OF FIRE FYDRANT AND MISC AREA AND WATER SUPPLY IN MAP ACCN IN ZONE B AND C AND MODERNISED INFRA OF COD UNDER AGE E/M OF GE (EAST) JABALPUR

Amount

Excavation in trenches, not exc 1.5 mtr wide and not exc 1.5 mtr deep for fundations, manholes, laying GI/CI pipes etc n.exc 10Sqm on plan and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exce 25Cm thick complete all as specified and directed.

Removing excavated soil to a distance not exc 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

Cutting existing the following cast iron pipes in position for insertion of new pipe/tees, branches etc. complete all as specified.

250 mm bore

200 mm bore

150 mm bore

100 mm bore

Taking up the DI water mains (including all fittings) of size 150 mm dia incuding flanged ends rubber joints with spigot and socket ends and lead joint including burning out joints and recovering lead of size. Note : Excavation/earth work shall be measured and paid separately under relevant items.

S&F Ducitile iron pipe double flanged ISI marked 150 mm Daimeter, 3- 6 mtr length in Each pipe, 4 mm thickness, finished polished in round shape for drinking water all as specified and directed by Engr-in-Charge, Location : Mandir line & Church line.

M&L for run lead joints for the following size of pipes complete for water mains with spigot & socket pipes and fittings complete all as specified and directed :-

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F the following rubber tyton joint of following size :-

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F rubber gasket joint for flanged end pipe & fittings of following size :-

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F in repairs machanical Gypsum joint ISI marked for spigot end pipe of following sizes:-

250 mm bore

200 mm bore

150 mm bore

100 mm bore

80 mm bore

S&F 200/250mm bore spigot/flanged/ socketed CI fittings such as bends (any type radius and angle), tapers, tees, collars & tail piece socket/flanged/spigot etc complete all as specified.

Dismantling/taking out unserviceable sluice valve of size 80mm to 250mm bore dia by opening/cutting rusted nuts, bolts etc all as specified and directed.

S&F the following CI sluice valves both ends flanged and drilled, bonnet wedge stuffing box. Gland trust plate, hand wheel made out of grey CI, complete valve confirming to IS 14846/2000 and its fittings suitable for hydraulic test pressure of 15 Kg/sqcm PN 1.0 ISI marked complete all as specified and directed :- Make : Kirloskar/L&T/Upadhiya

80 mm bore

100 mm bore

S&F the following CI sluice valves both ends flanged and drilled, bonnet wedge stuffing box. Gland trust plate, hand wheel made out of grey CI, complete valve confirming to IS 14846/2000 and its fittings suitable for hydraulic test pressure of 15 Kg/sqcm PN 1.6 ISI marked complete all as specified and directed :- Make : Kirloskar/L&T/Upadhiya

150 mm bore

200 mm bore

250 mm bore

Dismantling/taking out unserviceable air release valve/non return/foot valve/fire hydant valve of any size by opening/cutting rusted nuts, bolts etc all as specified and directed.

Supply and fix CI double end flanged and drilled non return valve of size 200 mm PN-1.6 dia ISI marked. Make : Kirloskar/Upadhyay/L&T

Supply and fix CI double end flanged and drilled non return valve of size 150 mm dia PN-1.6 ISI marked. Make : Kirloskar/Upadhyay/L&T

Supply and fix CI double end flanged and drilled non return valve of size 100 mm dia PN-1.6 ISI marked. Make : Kirloskar/Upadhyay/L&T

Supply and fix CI foot valve, flanged end and drilled of size 150 mm dia ISI marked. Make : Kirloskar/Upadhyay/L&T

Supply and fix CI foot valve, flanged end and drilled of size 100 mm dia ISI marked. Make : Kirloskar/Upadhyay/L&T

Supply and fix cast iron double ball air release valves of size 80mm as per IS 14845, PN rating H-7 ISI marked. Make : Kirloskar/Upadhyay/L&T

Cutting of road / hard standing for laying / dismentling of pipe line and making good surfaces matching with the existing surface after laying of pipe line.up to 30 cm.

Dismantling of existing valve pit and M&L for construction of masonry valve pit (as per drawing No CEJZ/TD/819/91 dated 16/04/91) with the following specification :- Necessary excavation earthwork in any type of streta, returning filling, surplus soil removing as directed, Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 1200 x 1200 x 1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mm x 40mm x 5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing.

Dismantling of existing valve pit and M&L for construction of masonry valve pit (as per drawing No CEJZ/TD/819/91 dated 16/04/91) with the following specification :- Necessary excavation earthwork in any type of streta, returning filling, surplus soil removing as directed, Brick work in CM (1:4) with sub class 'B' bricks, 15mm thick plastering in CM (1:4), PCC (1:4:8) type D-2 in foundation, chamber of internal size 900 x 900 x 1200 mm,150mm thick copping on top in PCC (1:3:6), type C-1, 3mm thick MS sheet for cover, angle iron 40mm x 40mm x 5mm for frame all around with suitable handle with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primed on MS work and three coats of white wash and preparation of surfaces complete all as specified and shown on drawing.

Taking up or down the following old unserviceable GI Tubing and connections including cleaning for refixing :- Note :- Excavation/earthwork shall be measured & paid separately under relevant items.

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100mm bore

Refixing the following old GI Tubing and connections in New or old position (walls, Ceiling, Floors etc) of sizes :-

15 mm bore

20 mm bore

25 mm bore

40 mm bre

Laying only the followiing old serviceable removed GI Tubing from site and connection in New or old position (in trenches) of sizes :-

20 mm bore

25 mm bore

40 mm bore

50 mm bore

S&F the followiing GI tubing medium grade with all fittings and fixed complete laid in trenches of size :-

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100mm bore

S&F the followiing GI tubing medium grade with all fittings complete to walls and ceilings or laid in floors of size :

15 mm bore

20 mm bore

25 mm bore

40 mm bore

Taking down/removing the following unserviceable gate valve/stop valve from water supply lines, closing the opening with plug or preparing for new as required necessary fittings complete all as specified.

20 mm bore

25 mm bore

40 mm bore

50 mm bore

S&F the followiing Gun metal Globe or Gate valve with iron wheel head, screwed both ends for iron pipe and fixed with required necessary GI fittings complete :- Make : Kartar/Zolto/Sant/Leader

20 mm bore

25 mm bore

40 mm bore

50 mm bore

Taking down/removing unservieable bib taps 15/20mm bore from pipe line/tanks complete all as specified and directed.

S&F 15mm bore bib tap cast copper alloywith crutch/buterfly handle screwed for iron pipe complete all as specified. Make - Prayag/Polytuff.

S&F 15mm bore bib tap standard of PTMT any colour (minimum wt 15mm - 90gms) screwed for iron pipe complete all as specified. Make - Prayag/Polytuff.

Cutting the following existing galvanised iron pipe in position for insertion of new pipe/tees, branches etc :-

15 mm bore

20 mm bore

25 mm bore

40 mm bore

50 mm bore

80 mm bore

100 mm bore

S&F in replacement the following stainless steel spindle suitable for following dia of sluice valve complete with stainless steel nut and threading as per sample & directed by Engr-in- Charge :-

250 mm bore sluice valve

200 mm bore sluice valve

150 mm bore sluice valve

100 mm bore sluice valve

80 mm bore sluice valve

S&F in replacement Digital water leval indicator system 150 mm size digit direct display, operated on 230v Ac, suitable for upto 20 metre height over head Reservior/underground sump of any capacity, preadjustable alarm for upper & lower level, temp range - 5 to 50 degree, humidity up to 90% RH, reset push switch for silent the alarm including 4 core 1.5 sqmm copper cable. Make: SURYA ELECTRONICS & CONTROLS / RECTRONIC DEVICE & CONTROLS. Location :-HQ CMM OH Tank & Mandir line OH Tank.

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 17.5HP/15 HP Pump Set. (i) Transportation of submersible pump -motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3 phase, taking out burnt winding wire, with & including PVC insulated water proof copper wire with winding wire of appropriate gauge and turn, providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Engr-in-Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, including cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 17.5/15 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer, assembling the pump and motor including testing complete all as specified and directed.

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 12.5/10 HP Pump Set. (i) Transportation of submersible pump -motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3 Phase, taking out burnt winding wire, with & including PVC insulated water proof copper wire with winding wire of appropriate gauge and turn, providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Engr-in-Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, incl cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 12.5/10 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer, assembling the pump and motor including testing complete all as specified and directed.

Taking up Submersible Pump assembly including column pipe approx 50 to70 mtrs using chain pulley block manually and carrying out following phase of work all as directed for 7.5/5 HP Pump Set .(i) Transportation of submersible pump -motor assembly for necessary repair. (ii) Carrying out overhauling of motor assembly 3 Phase ,taking out burnt winding wire,with & including pre insulated water proof copper wire with using winding wire of appropriate gauge and turn, providing insulation materials and replacement of bearing and assembling with repaired/serviceable pump and testing complete all as directed by Eng-in Charge. (iii) Carrying out dismantling and overhauling of multi stage pump, including cleaning and derusting of casing, replacement of worm out spare like bearings, impellar bushing, coupling etc & refixing of existing serviceable components after proper cleaning, machining all as required & assembling testing at workshop complete for 7.5/5 HP submersible pump of any make including carrying out painting by two coats of synthetic enamelled paint over a coat of primer,assembling the pump and motor including testing complete all as specified and directed.

Note for Srl item No 38 to 40. (i) Cost of disconnection of electric connection from LT control panel & starter of submersible pumping set & reconnecting with existing pipe and making electrical connection with panel board & starter shall be included in the quoted rate of these items. (ii) Cost of lowering of submersible pump set of any size after repairs and re-connecting with existing pipe shall be included in the quoted rate of these items. (iii) Cost of spare parts shall be included in the quoted rate of these items. (iv) The contractor shall be repair the submersible pump and motor within 72 hours after receiving the complaint failing which recovery/penalty shall be imposed @ Rs 500.00/day. The same shall be recovered from the RAR/FB.

Disconnecting electrically and disengaging the AC Squirrel cage induction motor 3 phase 415 Vlots, 50 Cycles, and taking out to local workshop induction motor 60/50/40 HP for repair purpose including complete cleaning,varnishing, insulation and greasing and including shifting back to location as directed, installing, testing and commissioning after repair complete all as specified and directed. Note- Rewinding will be measure & paid seperately under relavant item of schedule.

Disconnecting electrically and disengaging the AC Squirrel cage induction motor 3 phase 415 Vlots, 50 Cycles, and taking out to local workshop induction motor 12.5/15/25 HP for repair purpose including complete cleaning, varnishing, reinsulation and greasing and including shifitng back to location as directed, installing, testing and commissioning after repair complete all as specified and directed. Note :- Rewinding will be measure & paid seperately under relavant item of schedule.

M&L for Rewinding the motor with super enamelled copper winding wire with appropriate same gauge of exsisting coil with similar class of exsisting insulation as recommended by manufacturer with high quality normex insulating paper applying best quality insulating varnish on stator/rotor windings drying them completely, testing the insulations as directed by Engr-in-Charge. Make : Atlas/BWC/Swastik/Chetak.

Taking down unservicable existing motor starter of any size/capacity.

M&L Fully Automatic Star Delta Motor starter 50 HP in sheet-steel enclosure type ML with single phase protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 28-42 complete all as specified. Make : L&T cat no SS 91730 or Equivalent of SIEMENS/schneider.

M&L Fully Automatic Star Delta Motor starter 35 HP in sheet-steel enclosure type ML with single phase protection feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 22-32 complete all as specified. Make : L&T cat no SS 91730 or Equivalent of SIEMENS/schneider

M&L Fully Automatic Star Delta Motor starter 25 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 13-21 complete all as specified. Make : L&T cat no SS 91855 or Equivalent of SIEMENS/schneider.

M&L Fully Automatic Star Delta Motor starter 15 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 11-18 complete all as specified. Make : L&T cat no SS 96257 or Equivalent of SIEMENS/schneider

M&L Fully Automatic Star Delta Motor starter 12.5 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 9-14 complete all as specified. Make : L&T cat no SS 96257 or Equivalent of SIEMENS/schneider.

M&L Fully Automatic DOL Motor starter 7.5 HP in sheet-steel enclosure type MK-1 .feature (Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) and Relay Range 13-22 complete all as specified. Make : L&T cat no SS 96228 or Equivalent of SIEMENS/schneider

M&L Fully Automatic DOL Motor starter 3 HP in sheet-steel enclosure type MF-1. feature (Motor Rating AC-1 Duty, 230V, 50Hz, 1-Ph) and Relay Range 10.5-17.5 . Make : L&T cat no cs90319kodo or Equivalent of SIEMENS/schneider.

Taking down unservicable existing cable from motor/pannel to starter any size/capacity

S & F PVC Insulated unsheathed cable 10 sq mm, 3 core, multistranded bright annealed copper conductor 1100 volts, including taking down conf to IS-694 complete all as specified. Make : Policab/Havells/Finolex

S&F in repairs MCCB 250 A 35 KA, 4 POLE, thermal magnetic relese, Ics=100% Icu complete all as specified. Make : L&T / Schneider/Hager

S&F in repairs MCCB 200 A 35 KA,4 POLE, thermal magnetic relese, Ics=100% Icu complete all as specified. Make : L&T / Schneider/Hager

S&F in repairs MCCB 160 A 35 KA, 4 POLE, thermal magnetic relese, Ics=100% Icu complete all as specified. Make : L&T / Schneider/Hager

S&F in repairs MCCB 125 A 25 KA,4 POLE, thermal magnetic relese, Ics=100% Icu complete all as specified. Make : L&T / Schneider/Hager

S&F in repairs MCCB 100 A 25 KA, 4 POLE, thermal magnetic relese, Ics=100% Icu complete all as specified. Make : L&T / Schneider/Hager

S&F in repairs MCCB 63 A 16 KA,4 POLE ,thermal magnetic relese, Ics=100% Icu complete all as specified. Make : L&T / Schneider/Hager

M&L draining water from OH reservoirs not exc. 18 Mtr head/staging, and cleaning internal portion of tank (bottom and walls) by means coir / wire brush etc. and wash the internal portion of tanks by using bleaching powder @ 25 grams per 1000 Ltrs of water after removing sludge and mud etc to a distance not exc 50 mtr including one coat of synthetic enamel paint on all steel surfaces such as ladder, railing, inlet & over flow CI pipes connected sluice valves of the respective OH tanks/ground level reservoir etc writing letters with white paint (date of cleaning and capcity of tank) on black painted surface of tanks all as directed by Engineer-in-Charge.

100000 gallons capcity.

50000 gallons capcity.

Same all as Srl item No 60 above but exceeding 18 Mtr head / staging for the following :-

100000 gallons capcity.

Same all as Srl Item No 60 above but semi underground reservoir/sump of 200000 gallons cap each tanks devided in two poriton.

Same all as Srl Item No 60 above but semi underground reservoir/sump of 100000 gallons cap each tanks devided in two poriton.

Same all as Srl Item No 60 above but semi underground reservoir/sump of 50000 gallons cap each tanks devided in two poriton.

Same all as Srl Item No 60 above but semi underground reservoir/sump of 25000 gallons cap each tanks devided in two poriton.

Supply instll commissining and testing in repairs of CPRI Approved floor mounted outdoor cubicl type LT Feeder Pillar Box of uitabl size abricated out of 3.15 mm thick CRCA Sheet and angle iron 50 x 50 x 6 mm frame factory made totally enclosed dust and vermin proof both side hinge opening arrngement on front and back with locking arrangement cable entry and exist from bottom with cble glands and gaskets, Copper bus bar 750 Amps rating fixed on porcelain insulator with inernal wiiring with suitable size of Copper strips to be used for incoming and outgoing connection of all switchs/MCCB"s & Bus-bar, Bus-bar shall be insulated with colour code sleeves/tapes and to be connected with copper lugs, including two coats of synthetic enameled paint on the surfce externally & internally over a coat of red oxide primer paint incl, necessary PCC (1:3:6) type C2 as in foundation all as directed, comprising of the following :-

(a) INCOMING

(i) Thermal magnetic and microprocessor release MCCB 500 Amps, 4 Pole, 45 KA with front operated locking device - 01 Nos.

(b) OUTGOING

Supply install commissioning and testing CPRI Approved floor mounted outdoor cubical type LT Feeder Pillar Box of suitable size fabricated out of 3.15 mm thick CRCA sheet and angle iron 50 x 50 x 6 mm frame factory made totally enclosed dust and vermin proof both side hinge opening arrangement on front and back with locking arrangement cable entry and exist from bottom with cable glands and gaskets, copper bus bar 450 Amps rating fixed on percelain insulator with internal wiring with suitable size of a copper strips to be used for incoming and outgoing connection of all switches/MCCB's & Bus-bar, Bus-bar shall be insulated with colour code sleeves/tapes and to be connected with copper lugs, including two coats of synthetic enameled paint on the surfce externally & internally over a coat of red oxide primer paint incl, necessary PCC (1:3:6) type C2 as in foundation all as directed, comprising of the following :-

(a) INCOMING

(i) Thermal magnetic and microprocessor release MCCB 300 Amps, 4 Pole, 45 KA with front operated locking device - 01 Nos

(b) OUTGOING

S&F in repairs 15 HP submersible pump set suitable for 150-200 mm boreing, 1-447 mtr head, 30-740 LPM discharge, including all accessories all as specified and directed by Engr-in-Charge. Make -KIRLOSKAR 15 HP BOREWELL SUBMERSIBLE PUMP SET 100HHN-1515 or CROMPTON 15HP BOREWELL SUBMERSIBLE PUMP 8W3K15D-W or Havells Submersible Pumpsets Water Filled Motor H6W6M3F150T 11.2 kW 15 HP.

S&F in repairs 10 HP submersible pump set suitable for 150 mm boreing, 5-306 mtr head, 60-2400 LPM discharge, including all accessories all as specified and directed by Engr-in-Charge. Make- KIRLOSKAR 10 HP BOREWELL SUBMERSIBLE PUMP SET KS6F-1006R orCROMPTON 10 HP SUBMERSIBLE PUMP SET 650CS100-1010 or Havells Submersible Pumpsets Water Filled Motor 7.5 kW 10 HP.

S&F in repair centrifugal pump 1 HP, single phase, 9-22 mtr head, brass impeller, with complete accessories all as specified and directed by Engr-in-Charge. Make-CROMPTON 1 HP MBG12 CENTRIFUGAL WATER PUMP or KIRLOSKAR 1 HP 210V 0.75 KW SINGLE PHASE MONOBLOCK PUMPS KDS-128+ or V-GUARD MONOBLOCK PUMP NEON-WSF100.

Note. Srl Item No 68, 69 & 70 catered against BER items.

Schedule of credit amount of Rs. 4,18,937.00 to be deducted during AOC

Goodluck Enterprises

SHIVALIK ENGINEERING WORKS

shri krishna traders