PROVN OF SECURITY POST WITH GUARD ROOM ALONGWITH TOILET AND BATHROOM AT 16 CSR AT NAGROTA MIL STN UNDER GE NAGROTA

Amount

Surface dressing not exc 15 cm deep and getting out in any type of soil.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,cables, etc. n exc 10 sq m on plan and getting out in any type of soil.

Excavating in trenches, n exc 1.5 m wide and exc 1.5 m but n. exc 3.00 m in depth; for foundation, etc. and getting out in hard/dense soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point.

M&L for cement concrete type D2, 1:4:8 mix (using 40 mm graded aggregates)as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix (using 20mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete.

Formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; similar work; vertical or to batter for rough finished surface of concrete(flat), complete all as specified and directed..

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cracking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

Mild steel TMT bars 5mm to 10mm dia, cut to length, in stirrups, spacers & binders.

Mild steel TMT bars 6mm dia and over, cut to length, bent to shape required including cracking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete.

M&L for Reinforced cement concrete (M-25 design mix) as in Columns, pillars, piers, posts and struts.

Formwork to sides and soffits of floor or roof beams, beam haunchings, griders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete.

M&L for Reinforced cement concrete (M-25 design mix) in Beams, cantilevers, bressummers, lintels over 1.5m span (using 20 mm graded aggregates)

M&L for Reinforced cement concrete (M-25 design mix) as in Chajjas

Formwork to chullah hoods, chajjas, troughs and similar items including edges in rough fininshed surface of concrete(flat).

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Reinforced cement concrete (M-25 design mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs and in shelves and the like (using 20 mm graded aggregate)

Brick work with sub-class `B' bricks, straight or curved on plan with modular bricks exceeding 6 M mean radius built in cement mortar 1:6, complete all as specified.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to anyradius in half brick thick walls built in cement mortar 1:4, complete all as specified.

Rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM 1:3 on ceiling finished even and smooth without using extra cement.

Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 on walls finished even and smooth without using extra cement.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 on walls and finishing the surface even and smooth without using extra cement.

Preparing newly plastered surfaces of walls and applying two coats of distempering walls with distemper dry, white or tinted.

Preparing new plastered surfaces of walls and applying two coats of cement base paint.

Preparing newly plastered surfaces of ceilings and applying three coats of white wash.

S&F pressed steel frame for door with two rebate including necessary fixing lugs, hinges, lock strike plate complete all as specified of size 105x60mm.

S&F pressed steel frame for door with two rebate including necessary fixing lugs, hinges, lock strike plate complete all as specified of size 125x60mm.

M&L for cement concrete type C1, 1:3:6 mix, (using 20 mm graded aggregates) as in filling and mass concrete for hold fast and back filling for door frame.

S&F 2nd class hard wood, 40 mm thick plain, framed panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers, fitted to chowkhets.

S&F 2nd class hard wood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc with sash bars, edges of framing plain, chamfered or rounded. Fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) , supplied and fitted to chowkats etc

S & F Box type Steel windows/vent with double shutters (inside for wiremesh & out side for glass), incl guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.Steel window shall be conforming to relevant IS complete all as specified and directed by Engr-in-Charge.

S & F solid PVC door frames of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and as directed.(Make Rajshri Plastiwood limited or Sintex or equivalent)

S & F factory made solid panel PVC door shutter with wood free EPS 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification.(Make Rajshri Plastiwood limited or Sintex or equivalent)

S&F 3mm thick sheet glass, ordinary qaulity,in squares n exc 0.5 sqm in each pane, complete all as specified.

S&F 3mm thick pin head glass, ordinary qaulity,in squares n exc 0.5 sqm each panes etc all as specified.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc all as specified.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section and fixed.

S&F 100mm long aluminium anodised barrel tower bolt of extruded section and fixed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F 100mm mild steel butt hinges, medium weight, cold rolled and fixed.

S&F 150mm long aluminium handles cast type, anodised and fitted.

S&F 100mm long aluminium handles cast type, anodised and fitted.

S&F 300mm long ordinary MS rat tail rod pattern springs including roller and roller plate complete.

M&L two coats of synthetic enamel paint over a coat of pink primer on new wood or wooden surfaces, over 10 cms width or girth including preparation of surfaces.

S&F in repair harrison rails, mild steel, chromium plated with fixing brackets, stops, roller etc

Hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface with material and labour, broken stone or boulders.

M & L for 75 mm thick PCC 1:3:6 type C2 as in plinth protection & finishing the surface even & fair without using extra cement complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 as a sub base to receive topping layer finished even and rough complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement mortar (1:4) 20mm thick screed base laid and mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for machine cut kota stone 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement mortar (1:3) 10mm thick screed base laid and mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for non-skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in while or coloured cement to match etc all as specified.

M&L glazed, coloured, ceramic, tiles of size (450mm x 350 mm) x 7 mm thick, on vertical surfaces, such as dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles all as specified and directed.

S&F vitreous china squatting pan Orrisa pattern 580x440mm white with integral foot rest (excluding flushing cistern) fixed in repairs

S& F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve float and handle including brackets (10 ltr) including mild steel tube 32mm dia flush pipe.

S&F vitreous china wash basin angle back, size 600x480 mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and as directed .

S&F in the wall, soap dish, vitreous china white, approximate size 160x160x90 as in repairs

Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)

S & F 15 mm dia GI tubing medium grade with all fittings and fixed complete to walls or laid in floors.

Cutting chases, pinning in, making good to facing where rerquired and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels,etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth in brick walls

S & F 20mm dia GI tubing medium grade with all fittings and fixed complete to walls or laid in floors.

S & F 25mm dia GI tubing medium grade with all fittings such as bends, elbow, sockets, reducer and fixed complete to walls and ceiling or laid in trenches, complete all as specified.

S & F 15mm bore chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F gunmetal globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe of high pressure complete all as specified and as directed.

S&F gunmetal globe or gate valves 25mm dia with iron wheel head, screwed both ends for iron pipe of high pressure complete all as specified and as directed.

M&L for cutting of existing underground GI tubing water main of suitable size dia including inserting GI Tee of suitable size and all necessary fittings and jointing material complete all as specified and directed by Engr-in -charge

S&F in repair Glass corner Shelf of 300mm long all as specified and directed by Engr-in-Charge

M&L for 75mm dia cast iron Nahani Trap, with grating including jointing to waste pipe fixed in concrete type B1(1:2:4)

S&F PVC SWR gully trap 125/110mm, setting and jointing with solvent cement with grating including jointing to waste pipe fixed in concrete type B1(1:2:4)

S&F Grating doom round 140mm size of PTMT (minimum weight 50gms)

S&F brass chromium plated tubular towel rail,20mm dia, D type, 60cm long between flanges.

S&F PVC connection 15mm size with PTMT nuts of length 600mm

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of bore 75mm.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of bore 110mm.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls of bore 75 mm.

S&F PVC (SWR) vent cowl bore 75 mm.

S&F PVC (SWR) 75 mm bore bends (any radius) fixed with cement joint.

S&F PVC (SWR) 110 mm bore bends (any radius) fixed with cement joint.

S&F 110 x 75mm bore PVC (SWR) reducer fixed to walls with cement joint complete all as specified and directed.

S&F PVC (SWR) 110 mm bore branch piece (Tee) fixed to walls with cement joint with or w/o ovel access door complete all as specified and directed.

S&F 1000 ltr capacity Rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified.

S&F 20 mm dia Ball valve PTMT valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule.

Mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways, flat iron ,railings, frame work of water tanks and similar work conforming to E-165 (Fe-290) complete all as specified and directed by Engineer-in-charge.

Preparing new steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a priming coat of red oxide primer complete all as specified and directed.

M&L preparation of new steel and iron surfaces of any description n exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M&L for 10 mm rendering in CM 1:4 including water proofing compound @2% of cement over roof surfaces finished even and smooth without using extra cement complete all as specified Note:- WPC shall be measured and paid separately.

Supply only for Integral water proofing compound.

Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces

Applying evenly a tack coat of induatrial bitumen 85/25 grade @ 1.2 Kg/Sqm.

One layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm , reinforced with non woven polyester fabric or weight not less than 150 gms per Sqm . Polymeric membrane shall be taken to a height 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing(Note (i) Laying of APP based polymeric membrane shall be done by torch on method or as per manufacturers instructions (ii) A Minimum overlap of 100 mm and 75 mm should be made in the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as manufacturers instructions (iii) The make of polymeric membrane shall be IWL India Ltd chennai. Ltd or "MOPLY FP" of Texsa India Ltd). NOTE : S&F of APP based polimeric membrane of approved manufacturer will be laid/fixed by authorised person of the same manufacturers units as per relevent IS.

Applying two coats of aluminium paint on top of APP membrane.

M&L for 75mm thick PCC 1:4:8 D-2 (using 40mm graded crushed stone aggregate) as a sub base to chequered tile finished even and rough, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 B-1 (using 20mm graded crushed stone aggregate) as a sub base to cheqeured tile finished even and rough, complete all as specified and directed.

M&L for 20mm thick screed or screed bedding in cement mortar 1:4 as a base to chequered tile, complete all as specified and directed.

M&L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick , set, jointed and pointed in neat slurry with grey cement and pigments, complete all as specified and directed.

S&F UPVC (SWR) pipes single socketed waste and vent pipes 110mm dia bore in any length with rubber ring joints laid in floor complete all as specified

Concrete bed to drain pipe including packing and haunching against the sides of pipe after they are laid and tested for 100 mm bore pipe in PCC 1:3:6 type C-2 complete.

M&L brick work with sub class B brick straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed

M&L for rendering 15mm thick in CM 1:4 on brick work or concrete surfaces finished even and smooth without using extra cement including mixing of liquid water proofing compound in the proportion as per manufacturer's instruction (WPC will be measured and paid separately)

Supply only liquid water proofing compound ISI marked complete all as specified and directed

M & L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in copings, benching etc including necessary formwork complete.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mittred/stoped ends etc complete all as specified and directed

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in manhole /drain slab cover all as specified and set in CM 1:4 complete.

S&F On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc complete for 25 users complete all as specified.

Construction of Soakage wells including excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.20m dia X 3.0m effective depth complete all as specified and directed.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick bakelite laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following :-

(a) One light point controlled by one switch 5 Amp.

(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp

(c) One socket out let 5 Amp controlled by one switch on independent board.

All as per item No 112 here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independent board.

S&F switch piano flush type 5 Amps single pole one way complete.

S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete.

S&F switch socket combination 2 in 1, 5 pin, 5 /15 Amps flush type complete.

S&F of ceiling rose, surface type 65mm x 50mm, 2 to 3 terminal complete PVC/Polycarbonate isolated body complete all as specified and directed.

Supply and fixing LED light fitting 1x 18W/20W, 220V, AC, including LED tube light and connecting up with flexible copper conductor cable of suitable size from ceiling rose complete.

S & F LED light fitting 1x9W bulkhead luminaires IP 65 complete with all accessories including LED lamp 9 watt, connecting up with twin core flexible copper conductor cable of suitable size of 230 V, 50 Hz.

S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F for LED bulb 7 watt complete all as specified and directed.

S&F sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete

S&F MCB SPN 63 A 10 KA 240 volts "C" series complete

S&F MCB single pole 6 to 32 Amps 10 KA 240 volts "C" series complete

S&F Exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm including cutting of hole of required size.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00, BEE five star rated with brushless direct current motor (BLDC) compatible conventional fan regulator complete.

S&F electric water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 Ltrs, BEE 5 star rated complete with accessories such as safety valve, thermostate, NRV, connection pipe etc.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion complete.

Sand cushioning to under ground cable laid in trenches for laying of LT UG cables 8 cm depth before laying the cable and 15 cm after laying and punned down to a depth of 10 cm as per MES SSR Part-I (2009) all as specified and directed. Note: Punned thickness shall be measured and paid to the contractor.

M&L for brick covering with width equal to length of brick as mechanical protection to cables with well burnt sub class 'B' bricks laid dry flat complete all as specifed and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm 2 core complete all as specified.

Steel tubing galvanised (light grade) 40mm bore conforming to IS-1239 for passing cable under road/floor or fixing to poles for protection of underground cable complete with flat iron 50x6mm clamps made to shape and 12mm dia bolts, nuts and washers for fixing where required complete all as specified.

Supply and laying LED flood light 120W luminaire made up of epoxy coated pressure die cast aluminium housing conforming to IP-66 protection for optical compartment and control gear compartment. Built in surge protection upto 4KV and external surge protection upto 10KV provided for additional safety including complete electrical connection with fixing arrangement on pole or wall complete all as specified and directed by Engineer in charge.

BHARTI CONSTRUCTIONS

Karmnaya Construction

M/S MANISHA BUILDERS

ASHWANI KUMAR KHAJURIA AND SONS

CHARAN JIT SINGH

M/S SAHNI CONSTRUCTION CO

MAMTA ENTERPRISES