Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 C-82 at Inderpuri, New Delhi

Name of Work: Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

S. No. Description DSR Amount Non-DSR Amount Total Amount (DSR+NS)

S. No. Description DSR Amount Non-DSR Amount Total Amount (DSR+NS)

Earth Work 11,51,608.78 -

Concrete Work 10,62,060.74 -

Stone work 23,88,413.39 -

Roofing Work 10,63,588.49 -

Aluminium & UPVC Work 42,61,421.86 4,00,562.80

Road Work 8,42,882.04 -

Water Proofing 4,65,244.02 41,11,496.87

Terrace Garden 1,21,882.56 2,97,085.59

Sanitary Fixtures 3,32,441.10 25,69,755.00

Water Supply 24,91,733.33 -

Soil Waste & Pipe Fittings 49,946.80 8,11,651.05

External Drainage 7,53,324.25 -

Circuit Point wiring 27,15,646.00 -

Cable tray and accessories 7,38,980.00 -

Earthing installation 88,264.00 -

Distribution Board 4,58,860.00 -

Conduiting wiring and cabling for

Telephone/TV Netwrok system 3,05,536.00 3,56,600.00

Light item - 15,72,000.00

Cable, Mains and sub mains 28,110.00 15,54,733.85

CCTV System - 8,12,920.00

Electrical Panel - 47,83,758.00

DG Set and its accessories - 14,87,140.00

Total (Building Work excluding

Total Cost (including Furniture Work) 8,84,17,070.54 3,77,74,293.96 12,61,91,364.50

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

1 A Sub- Head I- Earthwork

1 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual cum 1428.39 177.50 253538.50 -

means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on

plan) including getting out and disposal of excavated earth, lead up to 50m and

for all lift ,as directed by Engineer-in-Charge. All kinds of soil.

2 2.10.1.1 Excavating trenches by mechinical / manual means of required width for pipes, cum 10.00 215.60 2156.00 -

cables, etc including excavation for sockets, and dressing of sides, ramming of

bottoms, for all depth, including getting out the excavated soil, and then

returning the soil as required, in layers not exceeding 20 cm in depth, including

consolidating each deposited layer by ramming, watering, etc. and disposing of

surplus excavated soil as directed, within a lead of 50 m :

All kinds of soil

Pipes, cables etc, not exceeding 80 mm dia.

3 2.22.1 Open timbering over areas including strutting, shoring etc. complete. sqm 241.94 44.85 10850.78 -

(Measurements to be taken of the face area timbered):

Depth not exceeding 1.5 m

4 2.22.2 Open timbering over areas including strutting, shoring etc. complete. sqm 241.94 54.95 13294.33 -

(Measurements to be taken of the face area timbered):

Depth exceeding 1.5 m but not exceeding 3 m

5 2.22.3 Open timbering over areas including strutting, shoring etc. complete. sqm 241.94 71.30 17249.97 -

(Measurements to be taken of the face area timbered):

Depth exceeding 3 m but not exceeding 4.5 m

6 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of cum 1722.38 196.00 337586.45 -

foundations etc. in layers not exceeding 20cm in depth, consolidating each

deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

7 2.26.1 Extra for every additional lift of 1.5 m or part thereof in excavation /banking cum 1540.99 126.80 195398.15 -

excavated or stacked materials. All kinds of soil

8 2.27 Supplying and filling in plinth with sand under floors, including watering, cum 77.94 2123.75 165525.08 -

consolidating and dressing complete.

9 2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees Sqm 871.36 17.6 15335.91 -

and saplings of girth up to 30 cm measured at a height of 1 m above ground level

and removal of rubbish up to a distance of 50 m outside the periphery of the

10 2.34.1 Supplying chemical emulsion in sealed containers including delivery as specified: litre 425.05 234.75 99779.84 -

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

11 2.35.2.1 Along the external wall below concrete or masonry apron using chemical sqm 765.09 53.45 40893.79 -

emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

12 Sub-Head II - Concrete Work

13 4.1 Providing and laying in position cement concrete of specified grade excluding

the cost of centering and shuttering - All work up to plinth level :

14 4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm cum 5.31 7878.50 41818.29 -

15 4.15 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded cum 14.04 7294.70 102417.59 -

stone aggregate 20 mm nominal size derived from natural sources)

16 4.20.1.1 Providing and laying in position ready mixed or site batched design mix cement cum 90.58 8835.15 800269.89 -

concrete for plain cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of laying,

curing, carriage for all leads; but excluding the cost of centering, shuttering and

finishing as per direction of the engineer-in-charge; for the following grades of

Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix

is more than 110% of the minimum specified cement content, the contractor

shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level : Concrete of M10 grade with minimum cement

content of 220 kg /cum

17 4.2.3 Providing & laying cement concrete in retaining wall , return walls ( any thickness Cum 11.88 9895.20 117554.98 -

) ,including attached pillasters,columns peirs, abuttments ,pillars ,posts , struts,

buttresses , string or lacing courses,parapets ,coping , bed blocks , anchor

blocks,plain window sills,fillets , sunken floors,etc.upto floor five level , excluding

the cost of centring , shuttering & finishing.1:2:4 ( 1 cement :2 coarse sand :4

stone aggregate20mm nominal size

18 Sub-Head- III- RCC Work -

19 5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope cum 8.64 11505.50 99407.52 -

up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,

staircases and spiral stair cases above plinth level up to floor five level, excluding

the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1

cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from natural sources).

20 5.9 Centering and shuttering including strutting, propping etc. and removal of form -

21 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 120.25 392.15 47155.65 -

22 5.9.2 Walls (any thickness) including attached pilasters, buttresses, plinth and string sqm 1370.46 842.50 1154609.18 -

23 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 414.11 927.25 383981.48 -

24 5.9.4 Shelves (Cast in situ) Sqm 86.40 927.25 80114.40 -

25 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. sqm 3008.69 736.40 2215597.11 -

26 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 1731.56 961.30 1664548.63 -

27 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 117.36 764.95 89774.53 -

28 5.9.14 Extra for shuttering in circular work (20% of respective sqm 583.69 185.45 108245.76 -

centering and shuttering items)

29 5.9.15 Small lintels not exceeding 1.5 m clear span, mouldings as in cornices, window Sqm 102.59 392.15 40228.71 -

sills, string courses, bands, copings, bed plates, anchor blocks and the like.

30 5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cm wide Rmt 844.20 208.55 176057.91 -

31 5.9.19 Weather shades, chajjas, corbels etc. including edges. Sqm 321.60 951.10 305873.76 -

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

32 5.9.20 Suspended floors, roofs, landings, balconies and access Sqm 2346.61 1028.40 2413254.73 -

platform with water proof ply 12 mm thick

33 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, kg 69300.64 107.85 7474073.92 -

placing in position and binding all complete upto plinth level. Thermo-

Mechanically Treated bars of grade Fe-500D or more.

34 5.22A.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, kg 141339.9 107.85 15243510.80 -

placing in position and binding all complete above plinth level. Thermo-

Mechanically Treated bars of grade Fe-500D or more.

35 5.30 Add for plaster drip course/ groove in plastered surface or moulding to metre 824.2 78.40 64614.14 -

R.C.C. projections.

36 5.33 Providing and laying in position ready mixed or site batched design mix cement -

concrete for reinforced cement concrete work; using coarse aggregate and fine

aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103

to accelerate / retard setting of concrete, to improve durability and workability

without impairing strength; including pumping of concrete to site of laying,

curing, carriage for all leads; but excluding the cost of centering, shuttering,

finishing and reinforcement as per direction of the engineer-in-charge; for the

following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix

is more than 110% of the specified minimum cement content, the contractor

shall have discretion to either re-design the mix or bear the cost of extra cement

37 5.33.1 All works upto plinth level.

38 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum. cum 644.31 9,504.75 6124008.13 -

39 5.33.1.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 20.00 9,655.70 193114.00 -

40 5.33.2 All works above plinth level upto floor V level

41 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum cum 860.31 9,504.75 8176987.85 -

42 5.33.2.2 Concrete of M30 grade with minimum cement content of 350 kg /cum cum 20.00 9,655.70 193114.00 -

43 5.41.1 Supplying and applying pre tested and approved water based concrete sqm 6811.76 69.05 470351.71 -

curing compound to concrete/ masonry surface, all as per manufacturer’s

specification and direction of Engineer-in-charge

Non pigmented wet curing compound

44 5.35 Add for using extra cement in the items of design mix over and above quintal 509.72 733.50 373881.95 -

the specified cement content therein

45 Sub-Head- IV- Brick Work -

46 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class cum 20.00 7,132.50 142650.00 -

designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6

47 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class cum 20.00 9,105.90 182118.00 -

designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

48 6.34.2 Brick work with non modular fly ash bricks conforming to IS:12894, class cum 299.26 8,752.55 2619287.24 -

designation 10 average compressive strength in super structure above plinth

level up to floor V level in :Cement mortar 1:6 (1 cement : 6 Coarse sand)

49 6.45.2 Brick work with non modular fly ash bricks conforming to IS:12894, class sqm 1888.56 1105.80 2088369.65 -

designation 10 average compressive strength in super structure above plinth

level up to floor V level in :Cement mortar 1:6 (1 cement : 6 Coarse sand)

50 NS-1 Providing and fixing chicken wire mesh of 150 mm wide fixed with U nails 150 Rmt 1100.00 38.00 0.00 41,800.00

mm centre to centre before plastering between junctions of column/beam and

51 Sub-Head- V- Stone work

52 7.32.2 Stone work, plain in copings, cornices, string courses and plinth courses, upto 75 cum 3.76 107965.10 405446.06 -

mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing

with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture

of pigment matching the stone shade.White sand stone

53 8.2.2.1 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and 0.00 -

prepolished, machine cut for kitchen platforms, vanity counters, window sills,

facias and similar locations of required size,approved shade, colour and texture

laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing to edges to give high gloss

finish etc. complete at all levels. Granite stone slab of colour black, cherry/Ruby

red or as approved by Engineer incharge

56 8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, metre 305.10 568.55 173464.61 -

in facia and drops of width upto 150 mm with epoxy resin based adhesive,

including cleaning etc. complete.

57 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., metre 392.10 510.95 200343.50 -

including machine polishing to edge to give high gloss finish etc. complete as per

design approved by Engineer-in-Charge. Granite work

58 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink Each 42.00 978.70 41105.40 -

in kitchen platform, vanity counter and similar location in marble/ Granite/ stone

work, including necessary holes for pillar taps etc. including moulding, rubbing

and polishing of cut edges etc. complete.

59 8.9.1.2 Providing & fixing Granite Stone (polished) work for wall lining over 12 mm thick Sqm 196.01 3860.00 756610.18 -

bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3

kg/sqm including pointing in white cement complete.Granite of any colour and

60 Sub-Head- VII- Wood & PVC work

61 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other cum 6.54 142949.70 934274.57 -

frames, wrought framed and fixed in position with hold fast lugs or with dash

fasteners of required dia & length (hold fast lugs or dash fastener shall be paid

for separately). Second class teak wood

62 NS-2 Providing and fixing factory made Prelaminated Solid door shutter made of 0.00 -

HDHMR Board (High Density High Moisture Resistance) of BSL(Metallic )grade.

,with prefinished both side laminate including liping,cutting rebate, fixing over

frame with stainless steel butt hinges Rate should include Door hardware of

Stainless steel (316 Grade) Door Knob,Hinges ( 125 mm ),

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

66 9.71.1 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) Each 324.00 129.85 42071.40 -

with stainless steel screws etc. complete : 125x64x2.50 mm

67 NS-3 Providing and fixing bright finished SS ASI 316 grade tower bolts with necessary Each 99.00 712.00 0.00 70,488.00

screws etc complete .300 x 10mm

68 NS-4 Providing and fixing bright finished SS ASI 316 grade tower bolts with necessary Each 12.00 1200.00 0.00 14,400.00

screws etc complete .600 x 10mm

69 NS-5 Providing and fixing bright finished SS-316 Grade 100 mm mortice latch and lock Nos. 99.00 3060.01 0.00 3,02,940.62

with 6 levers and a pair of lever handles with necessary screws etc. complete

(best make of approved quality).

70 NS-6 Providing and fixing SS (304) grade Double door buffer floor door stopper, ISI Each 99.00 386.75 0.00 38,287.76

marked, transparent or dyed to required colour and shade, with necessary

screws etc. comple te.Twin rubber stopper

71 NS-7 Providing and fixing Pull Handle- H Type (304 Grade)Back to back over Each 24.00 5648.00 0.00 1,35,552.00

Glass/Wood Door with necessary SS screws of complete as per direction of

Engineer in charge 25 mm x450 mm

72 NS-8 Supply & installation of Frameless Glass Partion for Bath shower. The Suspended sqm 86.94 7217.42 0.00 6,27,482.64

System held with Glass connector of SS-316 Grade Steel of approved

manufacturer & glass panel should be 12 mm thick clear toughened glass held

together . The Glass connector to fixed 3 nos on Floor & 3 nos in side wall with

screws all complete to perform as per specification and approved drawings .The

rate shall include all fitting fixers nut bolts, washer. all complete. For the purpose

of payment, actual elevation area of Glass shall be measured.

73 NS-9 Providing and fixing stainless steel grade 316 180 degree door viewer -PC finish. each 14.00 999.00 0.00 13,986.00

with necessary stainless steel screws etc. complete as per the direction of

Engineer-In-Charge.

74 NS-10 Supplying, installation, testing and commissioning of Digital door locks in each 12.00 17658.00 0.00 2,11,896.00

SS304 corrosion free having 5-in-1 Access (Bio+Pin+Card+Key with Wi-

Fi in builts) features, low battery alarm, Auto/Manual/Privacy locking

features , fMotice latch etc, compatible for door thickness of 35 mm - 60

75 Sub-Head-VII- Steel Work -

76 10.4 Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and sqm 7.56 6566.20 49640.47 -

diagonal braces of 40 x40 x6 mm angle iron, 3 mm M.S. gusset plates at the

junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at

the top and bottom respectively, including applying a priming coat of approved

77 NS-11 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan each 178.00 220.65 0.00 39,275.70

clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet

with its top surface hacked for proper bonding, top lid shall be screwed into the

cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock

at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per

standard drawing.

78 10.28 Providing and Fixing Stainless Steel (Grade 304) railing made of Hollow tubes, kg 3563.04 772.40 2752092.10 -

Channels, plates etc. including welding, grinding, buffing, polishing and making

curvature (wherever required) and fitting the same with necesarry stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories and

stainless steel dash fasteners, stainless steel bolts etc. of required size, on the

top of the floor or the side of waist slab with suitable arrangement as per

approval of Engineer-in-charge (for payment purpose only weight of stainless

steel members shall be considered excluding fixing accessories such as nuts,

bolts, fasterners etc.

79 Sub-Head- VIII- Flooring -

80 11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed sqm 721.47 1948.25 1405599.06 -

with grey cement slurry mixed with pigment to match the shade of the slab,

including rubbing and polishing complete with base of cement mortar 1 : 4 (1

cement : 4 coarse sand) :11.26.1 25 mm thick

81 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on sqm 2.86 2354.70 6725.02 -

12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed

with grey cement slurry mixed with pigment to match the shade of the slabs,

including rubbing and polishing complete.

82 11.55.1 Providing and laying flamed finish Granite stone flooring in required design and sqm 0.00 3186.70 0.00 -

patterns, in linear as well as curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick stone slab over 20 mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge : Flamed finish

granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

83 11.56.1 Providing and laying Polished Granite stone flooring in required design and Sqm 265.81 4481.30 1191169.87 -

patterns, in linear as well as curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick stone slab over 20 mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with

pigment of matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

84 NS-12 Providing and fixing Ist quality Ceramic glazed wall tiles of size not less 600 x sqm 838.59 1700.00 0.00 14,25,608.10

1200 mm conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, design & shades as approved by

Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed

of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement

slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment

of matching shade complete.

85 11.41A.2.3 Providing and laying Vitrified tiles in floor in different sizes (thickness to be sqm 1140.46 1728.80 1971623.96 -

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS:15622, of approved brand & manufacturer, in all colours and

shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing

with grey cement slurry @3.3 kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must be cut with the zero chipping

diamond cutter only . Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily.:

Glazed vitrified floor tiles polished finish of size of Tile 800 x 800 mm

86 11.41A.3.1 Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm sqm 407.83 1464.85 597412.71 -

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

87 11.46.3 Providing and laying Vitrified tiles in different sizes (thickness to be specified by sqm 98.74 1958.45 193369.52 -

manufacturer ), with water absorption less than 0.08 % and conforming to I.S.

15622, of approved make, in all colours & shade, in skirting, riser of steps, over

12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with

grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement

& matching pigments etc. complete. Size of Tile 800x800 mm

88 Sub-Head- IX- Roofing

89 12.21.1 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 metre 166.39 305.15 50773.91 -

stone aggregate 10 mm and down gauge) including finishing with cement mortar

1:3 (1 cement : 3 fine sand) as per standard design In 75x75 mm deep chase

90 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement Each 16.00 298.25 4772.00 -

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm

nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm

cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,

rounding the edges and making and finishing the outlet complete.

91 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes Rmt 298.40 377.40 112616.16 -

conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS

: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

92 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ 0.00 0.00 -

accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592

Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm

gap for thermal expansion

93 12.42.3 Single tee with door 110 mm Each 16.00 234.15 3746.40 -

95 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to Each 152.00 371.30 56437.60 -

unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs,

screwed with M.S. screws of required length, including cutting brick work and

fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall

etc. complete. 110 mm

96 12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm Each 16.00 54.70 875.20 -

diameter and weighing not less than 440 grams.

97 12.31.1 12.31 Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling Sqm 162.00 1718.95 278469.90 -

up to a height of 5 m above floor level, over first class kail wood

strips 25x6 mm with 10 mm gap in between and reinforced with

rabbit wire mesh fixed to wooden frame (frame work to be paid

separately): Flat surfaces

98 12.59 Providing & fixing false ceiling at all height including providing & fixing of 0.00 -

framework made of special section, power pressed from M.S. sheets and

galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277

and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of

27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash

fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed

to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I chanels

45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling

section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm

each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction

perpendicular to G.I intermediate channel with connecting clip made out of

2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter

channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the

perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at

99 12.59.1 :8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials Sqm 133.00 1572.30 209115.90 -

reinforced with cellulose fiber manufactured through autoclaving process.

100 12.52 Providing and fixing tiled false ceiling of approved materials of size 595x595 mm 0.00 -

in true horizontal level, suspended on inter locking metal grid of hot dipped

galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive)

consisting of main “T” runner with suitably spaced joints to get required length

and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at

1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm

thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm

center to center to form a grid of 1200x600 mm and secondary cross “T” of

length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to

be interlocked at middle of the 1200x600 mm panel to form grids of 600x600

mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved

texture in the grid including, required cutting/making, opening for services like

diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to

be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm

fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI

101 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size Sqm 181.13 1902.95 344671.82 -

595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having

galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester

powder coated of thickness 60 microns (minimum), including factory painted

102 Sub-Head-X- Finishing

103 13.4.2 12 mm cement plaster of mix : :6 (1 cement: 6 coarse sand) sqm 6472.61 343.65 2224312.43 -

104 13.5.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 sqm 2817.01 395.35 1113704.31 -

(1 cement: 6 coarse sand)

105 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) sqm 2760.72 300.45 829457.96 -

106 13.80 Providing and applying white cement based putty of average thickness 1 mm, of sqm 10078.57 156.05 1572761.00 -

approved brand and manufacturer, over the plastered wall surface to prepare

the surface even and smooth complete.

107 13.83.2 Wall painting with premium acrylic emulsion paint of interior grade, having VOC sqm 4137.91 142.80 590893.19 -

(Volatile Organic Compound ) content less than 50 grams/ litre of approved

brand and manufacture, including applying additional coats wherever required

to achieve even shade and colou r Two coats

108 13.85.3 Applying priming coats with primer of approved brand and manufacture, having sqm 769.95 73.95 56937.99 -

low VOC (Volatile Organic Compound ) content With water thinnable cement

primer on wall surface having VOC content less than 50 grams/litre

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

109 NS-13 Painting with acrylic emulsion paint of Stucco Marble satin finish and sqm 1941.78 1050.00 0.00 20,38,872.15

manufacture to give an even shade to wall and ceiling etc. applied evenly with

roller to give approved matt or stippled finish complete, including cleaning

preparation , putting etc. over coat of cement primer of surface and coat of

approved primer as per manufacturer’s specification:Two or more coats on new

work/and old work including scraping of old paint and disposal of mulba to

authorized dumping grounds.( for old and new work including peeling/removing

old paint. ) FOR ROOMS CEILING, TOILET, KITCHEN & CORRIDOR WALLS/CEILING

110 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture to sqm 553.30 226.25 125183.77 -

give an even shade : Two or more coats on new work

111 13.48.1 Finishing walls with textured exterior paint of required shade : 13.45.1 New work sqm 1645.46 223.60 367924.86 -

(Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat

of exterior primer applied @ 2.20kg/10 sqm

113 16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete cum 85.80 9823.80 842882.04 -

from batching plant. The ready mixed concrete shall be laid and finished

with screed board vibrator , vacuum dewatering process and finally finished

by floating, brooming with wire brush etc. complete as per specifications

and directions of Engineer-in-charge. (The panel shuttering work shall be

paid for separately).

(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/

less cement used as per design mix is payable/ recoverable separately).

114 Sub-Head -XI - Aluminum & UPVC Work

115 9.147.A Providing and fixing factory made uPVC glazed/wire mesh windows/ doors 0.00 -

comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler

(where ever required) extruded profiles having minimum wall thickness of 1.70

mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles

conforming to EN: 12608 in any shape, colour and design dully reinforced with

galvanized mild steel section made of required shape & size as per CPWD

Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor

(where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304

grade fasteners of minimum 8 mm dia with countersunk head, comprising of

matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS

1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel

screws etc. Profile of frame, sash & multion (if required) shall be mitred cut and

fusion welded /mechanically jointed duly sealed at all comers, including driling

of holes for fixing hardware and drainage of water etc. After fixing frame the gap

between frame and adjacent finished wall shall be filled with weather proof

silicon sealant over backer rod of approved size and quality all complete as per

116 9.147.C1.1 Fixed window/ventilator without mullion/transom.Using R1 series with frame Sqm 21.06 8247.25 1,73,687.09 -

(33 mm & above) x 135 mm & above). (Height upto 0.90 metre)

117 9.147.A4.1 Three track three panels sliding window with two glazed & one wire mesh panels Sqm 247.37 10993.55 27,19,419.50 -

with Aluminium channel for roller track, wool pile, nylon rollers with SS 304

body. Using R2 series with frame (70 mm & above) x (40 mm & above) & both

glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy

(zamak) powder coated touch locks with hook. (Height upto 1.2 metre)

118 9.147.B1.1 Two track two panels sliding door with Aluminium channel for roller track, wool Sqm 89.78 8106.30 7,27,743.08 -

pile, zinc alloy (zamak) powder coated handle on every panel along with multi-

point locking system, adjustable nylon rollers with SS 304 body. Using R3 series

with frame (55 mm & above) x (40 mm & above) & sash (30 mm & above) x (74

mm & above). (Height upto 2.5 metre).

119 21.3 Providing and fixing glazing in PVC / aluminum door, window, ventilator shutters - -

and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the

architectural drawings and the directions of engineerin- charge. (Cost of

aluminum snap beading shall be paid in basic item.)

120 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) sqm 233.15 1505.25 3,50,941.51 -

121 21.3.3 With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) sqm 67.33 1685.40 1,13,480.09 -

122 9.15 Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC Each 147.00 115.80 17,022.60 -

sliding window with necessary screws etc. complete.

123 9.15 Providing and fixing steel roller for uPVC sliding window with necessary screws Each 162.00 185.50 30,051.00 -

124 9.135.2 Providing and fixing fly proof stainless steel grade 304 wire gauge, to Each 105.11 1228.00 1,29,077.00 -

windows and clerestory windows using wire gauge with average width

of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all

complete. With 12 mm mild steel U beading

125 NS-14 Providing and fixing 19mm dia Stainless Steel drapery rod in required shade Rmt 228.35 1754.20 - 4,00,562.80

including rings, @ 100mm C/C, brackets, finial i.c fixing with necessary SS screws

and PVC sleeve etc. complete as per direction of Engineer in charge.

126 Sub-Head-XIII- Water Proofing

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

127 NS-15 Supplying and installing 1.5 mm composite thick fully bonded weldable HDPE sqm 634.44 1515.60 - 9,61,553.48

membrane conforming to IS 16471:2017 requirements of UG waterproofing

structures, requirements to provide Type A fully bonded protection of UG

waterproofing structures. The membrane shall exhibit 25 years of service life

tested and complied in accordance with EN 13251:2016 durability certification.

The membrane should be minimum 2.4 m wide comprising of an HDPE layer and

pressure sensitive adhesive layer which is covered by a weatherproof protective

layer with lap Joint Strength at overlaps >15000 N/m ASTM D 1876. The

membrane shall have minimum of 100mm side and end laps which shall be

thermofused with leister machines at all the joints for assuring watertightness

and achieving monolithic membrane. End laps and side laps should be a

minimum of 100 mm with the weld size of minimum 50 mm in case of a single

weld system. In case of a double weld system, comprising of two parallel welds

of 15 mm wide each with a 20 mm air channel gap in between the two weld

lines.The size of the membrane should not be less than 2.4 Mtr. x 20 Mtr. to

minimize the joints. This membrane shall be continued over the vertical surface

but terminated minimum 100mm below the top edge of the raft slab/footings

and fixed as per recommendation. Basic Propoerties are as follows:

1. Thickness of complosite memberane 1.5 mm

2. Tensile strength 25 mpa

3. Elongation 500%

4. Low temperature flexibility -25 Degree

5. Hydrostatic head resistance 70 m

6. Peel to concrete adhesion 1500 N/m

7. Lap Joint (side and end laps) peel adehesion 15000 N/m

8. Puncture rsistance 1000N

128 NS-16 Providing & applying 2 components, solvent free, liquid applied elastomeric sqm 503.74 2500.00 - 12,59,348.75

seamless hybrid Polyurea Polyurethane Membrane, using high pressure plural

component spray equipment, to form a minimum system thickness of 1.5 mm in

two or more passes with a total consumption of 1.5-1.6 kg / m2. The membrane

should have 100% Solids, VOC Free, Tensile strength 15 Mpa as per ASTM D 412,

Elongation 450% as per ASTM D 412, Low temperature Crack bridging ability of

3.2mm as per ASTM C 1305, Shore A Hardness 85 ASTM D 2240, Puncture

Resistance 1000 N as per ASTM E 154, Water Head Resistance 7 Bar as per ASTM

D 5385.The coating should pass Dynamic Crack Bridging as per EN 1062-7,

Method B for 20,000 cycles at -20 degree temperature. The membrane should

exhibit 25 years of service life tested and complied in accordance with EN

13251:2016 durability certification. Apply primer coat of epoxy primer by roller/

airless spray guideline and coverage @ 5-6 m2/ltr depends on porosity

of concrete. Allow to cure for max 5-6 hours. Broadcast anti slip grains of 200-300

micron (dried sand) on wet primer at coverage of 0.8-1 kg/m2 and allow to come

to touch dry condition before application of Membrane.

129 NS-17 Providing and fixing water profing treatment in Bath room/ toilet Providing and sqm 205.38 967.39 - 1,98,683.15

applying High Performance Two Component Acrylic Polymer Modified

Cementitious flexible flexible waterproofing, Dr. Fixit Fastflex having film build up

of 1.2mm to 1.5mm with elongation upto 120%. Applying coating in two coats

@1.0 kg/ M2/ coat in the time interval of 6-8 hrs. Coating shall be done on the

entire horizontal surface and vertical surface upto 7 ft from FFL adjust walls of

shower. (Rest upto 1ft.) After 2nd coat fine washed sand is sprinkeled on Vertical

wall while the coat is tacky for key to succesive plaster or screed. Note : 1st coat

must be applied on damp (SSD) surface not on dry surface. (Cement, sand,

electricity, water and other civil products should be supplied by civil contractor

for free of cost).Water Ponding Test : After 2nd Coat allow these coating to cure

for 7 Days as per curing process given in TDS. Check coating for any damage or

cracks during 7 days of curing. If found repair it. Cure it. Conduct Water Ponding

Test.Close all the outlets properly by suitable means. Fill the water minimum up

to 50mm height.Keep this water for maximum 48 Hrs.Observe the leakage or

130 NS-18 Providing & applying PU based high performance waterproofing treatment over Sqm 936.44 1806.75 - 16,91,911.50

terrace having pure polyurethane based, single component, low VOC,

elastomeric, seamless, moisture curing, waterproof membrane, Dr. Fixit FlexiPU

270(I), applied in 2 coats over After carrying the necessary preparation with

roller at a total consumption of 1.5 Kgs/Sqmt, having specific gravity of

minimum 1.30, having an elongation capacity of over 400%, with tensile strength

of > 2.00Mpa, Adhesion to concrete surface over 2.00N/mm2, Shore A Hardness

of 75, Fire resistance EURO Class-F, with Anti-root propertise, with a service

temperature range of -40deg C to 80deg C, with solids content of around 90%,

to be applied by brush/roller over the RCC slab and on the vertical surfaces upto

300mm above FFL, thereafter ponding with water for 3 days etc. complete. The

work shall be carried out all complete as per specification and the direction of

the engineer-in-charge. The product performance shall carry guaranteed for 10

years against any leakage

131 22.14.1 Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cum 61.94 7510.75 4,65,244.02 -

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

132 TERRACE GARDEN -

133 2.2 Supplying and stacking of good earth at site including royalty and carriage cum 93.64 469.50 43,965.86 -

up to 1 km (earth measured in stacks will be reduced by 20% for payment).

134 2.4.1 Supplying and stacking at site dump manure from approved source, cum 70.23 229.95 16,150.08 -

including carriage (manure measured in stacks will be reduced by 8% for

payment) : Screened through sieve of I.S. designation 20 mm

135 2.3 Supplying and stacking at site sludge from approved source, including cum 70.23 276.90 19,447.52 -

carriage (manure measured in stacks will be reduced by 8% for payment) :

136 2.8 Spreading of sludge, dump manure or/and good earth in equired thickness cum 234.11 46.15 10,804.18 -

(Cost of sludge, dump manure or/ and good earth to be paid separately).

137 2.9 Mixing earth and sludge and manure in proportion specified or as directed. cum 234.11 32.10 7,514.93 -

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

138 NS-19 Grassing with Selected type of I grass at Terrace in following stages: sqm 702.33 423.00 - 2,97,085.59

Stage-1:Providing & Laying of 13 mm thick Light Weight , high strength,Hi -

Impact Polypropylene modular drainage cells which is to be especially

designed for sub surface Drainage and Water Proofing Membrane

Stage-2 : Providing and Laying of Non -woven Geo Textile 150 gsm over

the Drainage Cells. Stage-3 :Supplying & Laying of Coco-pit Layer (

minimum 20 mm thick )

Stage-4:Grasing with Selected type of grass as approved by the Architect

including watering and maintenance of the Terrace lawn for 30 days or

more till the grass forms a thick lawn free from weeds.

139 2.5 Providing & fixing of White River (Stone) Pables size of 2" to 2.50" dia in Qtl 10.00 2400 24,000.00 -

natural colour at site of work including loading, unloading, carriage and all

taxes paid etc.and as per direction of officer in charge.

140 SANITARY FIXTURES

141 NS-20 Supply, Installation and commissioning approved make wash down wall 42.00 16914.00 - 7,10,388.00

mounted EWC conforming to IS:2556 (Part 16)-2002 with 'P' or 'S' trap

with concealed flush cistern fixed in wall(Viega Concealed Cistern with

Chrome Flush Plate with Press panel including, ultra solid seat cover of

approved make with rubber buffer and cap all of approved make etc.

complete for finished item of work in all respects Size : 515 x 350 x 330

mm Model.No.Reve. ( AV-2966 ) of Acquaviva or equivalent Make:

KOHLER,GROHE Each

Providing and fixing water closet squatting pan (Indian type W.C. pan )

with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with manually controlled device

(handle lever) conforming to IS : 7231, with all fittings and fixtures

complete, including cutting and making good the walls and floors wherever

required:White Vitreous china Orissa pattern W.C. pan of size

580x440 mm with integral type foot rests Each

143 NS-21 Providing and fixing wash basin with fixing arrangement, including C.P. 42.00 4198.00 - 1,76,316.00

brass waste of standard pattern, including painting of fittings and brackets,

cutting and making good the walls wherever require: Over the Counter

Wash basin of size 440 x 440 x 100,Model.No. ( AQV 76232 ) of

Acquaviva or equivalent KOHLER,GROHE Each

144 17.7A Providing and fixing wash basin with C.I. brackets, 15 mm dia CP 2.00 3960.55 7,921.10 -

Brass single hole basin mixer of approved quality and make, including

painting of fittings and brackets, cutting and making good the walls

wherever required:- (a) White Vitreous China Wash basin size 550x400

mm with a 15 mm CP Brass single hole basin mixer

145 NS-22 Providing & fixing premium make SENSOR TAP DECK MOUNT 42.00 10465.00 - 4,39,530.00

SHORT BODY for wash basin, and with 10 years warranty l as per

manufacturers specification and direction of Engineer-in-

charge.Separately)Model.No.Reve. (SF 7020, ,Acquaviva make ) Make:

Acquaviva or equivalent KOHLER,GROHE Each

146 NS-23 Providing and fixing Braided hose with Two 15mm Nuts & Rubber 42.00 501.00 - 21,042.00

washers without Nipple 6021Waste Coupling 32mm Full Thread : Model

No. BDC001 of Aquaviva make 45 cm length KOHLER,GROHE

147 NS-24 Providing and fixing Wall mounted Bathroom shaving Mirror 8"with 42.00 2818.00 - 1,18,356.00

expandle/adjustable : Model No. MIR-1855 of Acquaviva or equivalent

make.KOHLER,GROHE, Acquaviva Each

148 NS-25 Providing and fixing C.P. Brass 2864 Bib Tap Long Body Chrome Finish 42.00 615.00 - 25,830.00

as per model no. 2864 of jaquar or equvilent for wash basin.

(Make:Acquaviva, ).KOHLER,GROHE, Acquaviva Each

149 17.10.1.1 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 12.00 6945.60 83,347.20 -

with C.I. brackets and stainless steel plug 40 mm, including painting of fittings

and brackets, cutting and making good the walls wherever required :Kitchen sink

with drain board 510x1040 mm bowl depth 250 mm MAKE

(Kingstone/Nirali/Corrysil) Each

150 NS-26 Supplying, installing, testing and commissioning approved make 15mm CP 42.00 2875.00 - 1,20,750.00

health faucet with CP flexible tube 1.2 m long and wall hook (model no. HF 1812

Acquaviva make )- having High Quality plating in compliance with DIN and EN

standards including CP crutch, nozzle & 2 way Bib Cock with wall flange

etc.,complete. HF-1812 MAKES AQUAVIVA, KOHLER,GROHE

152 NS-27 Providing and fixing C.P. Brass divertor consisting concealed body and 42.00 8650.00 - 3,63,300.00

other parts as per model no. ALD055 ,Exposed parts kit consisting

operating lever wall flang as per model OPL-15065K and one spout

(Model AD-114 ,Acquaviva make) Including Concealed Part Make:

Acquaviva/Toto/Grohe Each

153 NS-28 Providing and fixing SS AISI-316 Grade Toilet Paper Holder with Flap 42.00 1903.00 - 79,926.00

complete with brackets fixed with CP brass screws PVC sleeves etc.

Complete: 155 mm long .Model No- TTPHF , of KICH, or

equivalent.(Make: Kich/Jaquar/Roca/ Cera/ Arch/ D-Line) Each

154 NS-29 Providing & fixing cockcroch trap S.S. grating of approved design for floor traps 102.00 558.00 - 56,916.00

etc. including setting in floor with cement mortar. 100 mm dia (Make:

Kich/Jaquar/Roca/ Cera/ Arch/ D-Line) each

155 18.50.1 Providing and fixing C.P. brass long nose bib cock of approved quality conforming 84.00 820.70 68,938.80 -

to IS standards and weighing not less than 810 gms.15 mm nominal bore

156 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of 84.00 574.30 48,241.20 -

approved quality conforming to IS:8931 15mm nominal bore Each

157 17.22A Providing and fixing CP Brass 32mm size Bottle Trap Model No 5001 Aquaviva of 42.00 1034.80 43,461.60 -

approved quality & make and as per the direction of Engineer-in-charge

158 NS-30 Providing and fixing SS AISI-316 Grade Towel rail complete with brackets fixed 42.00 1104.00 - 46,368.00

with CP brass screws PVC sleeves etc. Complete: 650 mm long .Model No- SDA-

060, of Acquaviva or equivalent,,(Make: Kich/Jaquar/Roca/ Cera/Grohe/ Arch/ D-

159 NS-31 Providing and fixing 600x120x5 mm Corner Soap Dish glass shelf with 42.00 1782.50 - 74,865.00

edges round off, supported on SS angle frame with C.P. brass brackets

and guard rail complete fixed with 40 mm long screws, rawl plugs

etc.Model No- SDA-056 of Acquaviva or equivalent Each

160 17.28.2 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. 12.00 119.55 1,434.60 -

waste fittings complete.Flexible pipe Each

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

161 NS-32 Supplying & Fixing of SS AISI-316 Liquid Soap Dispenser(Round Shape) 42.00 1895.00 - 79,590.00

200 ml capacity fixed to the wall with PVC rubber plug with CP brass

screws Model No- TLSD2S of KICH, or equivalent (Make:

Kich/Jaquar/Roca/ Arch/ D-Line) Each

162 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior nglass (of 42.00 1607.95 67,533.90 -

approved quality) complete with 6 mm thick hard board ground fixed to wooden

cleats with C.P. brass screws and washers complete.

163 NS-33 Providing & fixing cockcroch trap S.S. grating of approved design for floor traps 42.00 558.00 - 23,436.00

etc. including setting in floor with cement mortar. 100 mm dia

164 NS-34 Providing and fixing C.P Round Ceiling Mounted Shower of size 250 x 250 mm 42.00 5551.00 - 2,33,142.00

mm Single Flow with Rubit Cleaning System including, shower arm dia 20 mm &

450 mm Long round shape with Straight for ceiling mounted showers (Mode no:

RSs-1654 , Make Acquaviva .) (Make: Acquaviva /Xen/kingston

165 WATER SUPPLY

166 18.70 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot and cold water supply, including all CPVC plain and brass

threaded fittings. This includes jointing of pipes and fittings with one step CPVC

solvent cement and testing of joints complete as per direction of Engineer-in-

167 Internal work-exposed on wall, including fixing the pipewith clamps at 1.00

168 18.7.3 25mm nominal outer dia pipes. Rmt 774.75 401.55 3,11,100.86 -

169 18.7.4 32mm nominal outer dia pipes Rmt 776.55 518.75 4,02,835.31 -

170 18.7.5 40mm nominal outer dia pipes. Rmt 259.50 702.95 1,82,415.53 -

171 18.7.6 External work including trenching, refilling etc.50mm nominal outer dia pipes. 396.00 934.15 3,69,923.40 -

172 18.8.1 Internal work Concealed fixing the pipe with clamps at 1701.75 497.80 8,47,131.15 -

1.00 meter spacing including cutting chases and making good the wall etc.15mm

nominal outer dia pipes. Metre

173 18.17 Providing material and labour for fixing gun metal gate valve with C.I. wheel of 0.00 - -

approved quality (screwed end) :

176 18.18.3 Supplying & fixing of 25 mm dia Ball brass valves, high pressure, with polythene 67.50 464.05 31,323.38 -

float and flynut complete, screwed for iron pipe or brass ferrule and fixed

177 18.48 Providing material and labour for placing on terrace (at all floor levels) superior 18000.00 16.00 2,88,000.00 -

qualtity water storage tanks under the brand name SINTEX manufactured using

superior quality virgin raw material with four layer design in approved colours

including the ISI variety in black colour. The four layered thermally insulated

water tanks should be designed using the foam layer to minimize the effects of

sunlight & water cool in summers with cover . The rate shall including suitable

locking arrangement and making necessary holes for inlet, outlet and overflow

pipes but without fittings and the base support for tank

178 SOIL & WASTE PIPE & FITTINGS

179 NS-35 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings 497.90 521.00 - 2,59,405.90

type B for sewerage waste discharge system (IS:13592 : 1992 Marked) of

approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 100

180 NS-36 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings 630.70 378.00 - 2,38,404.60

type B for sewerage waste discharge system (IS:13592 : 1992 Marked) of

approved quality /make supreme, jain pipes, sudhakar, prince or equivalent 75

181 NS-37 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings 0.00 - -

type B for sewarage waste discharge system (IS:13592 : 1992 Marked) of

approved quality /make

182 Bend of required degree with access door, 0.00 - -

185 NS-38 Plain bend of required degree. 0.00 - -

188 NS-39 Heel rest sanitary bend 0.00 - -

191 17.44.2.2 Providing and fixing single equal plain junction of required degree :75x75x75 0.00 - -

mmSand cast iron S&S as per IS - 3989

193 EXTERNAL DRAINAGE

194 19.4.2.2 Providing and fixing square-mouth S.W. gully trap grade‘A’ complete with C.I. 19.00 2711.70 51,522.30 -

grating, brick masonry chamber with water tight C.I. cover with frame of 300

x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame

to be not less than 2.70 kg as per standard design 150 x 100 mm size P type With

Sewer bricks conforming to IS : 4885

195 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse 8.00 12770.55 1,02,164.40 -

sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III)

: 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix

(1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal

size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse

sand) finished with floating coat of neat cement and making channels in cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm

nominal size) finished with a floating coat of neat cement complete as per

standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with

frame (light duty) 455x610 mm internal dimensions, total weight of cover and

frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)

: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

196 19.60 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars 0.00 - -

jointed with stiff mixture of cement mortar in the proportion of 1;2 (1 cement : 2

fine sand) including testing of joints etc. complete:

199 19.20 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 0.00 - -

graded stone aggregate 40 mm nominal size) all-round SW/ RCC pipes including

bed concrete as per standard design:

200 19.2.2 150 mm diameter SW/RCC pipe Metre 188.00 1179.85 2,21,811.80 -

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

201 19.2.4 250 mm diameter SW/RCC pipe Metre 81.00 1590.55 1,28,834.55 -

202 19.27.1 Constructing brick masonry road gully chamber 50X45X60 cm with brick of class 12.00 5957.90 71,494.80 -

designation 75 in cement mortar 1:4 (1 cement : 4 coarse sand) including

500*450 mm pre-cast R.C.C. horizontal grating with frame complete as per

standard design: With F.P.S. bricks Each

204 18.42.3 Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils meter 57.00 1025.95 58,479.15 -

except ordinary hard rocks requiring blasting, including removing the casing pipe

after the hand pump / tube well is lowered and tested :Beyond 12 m and up to

205 18.43 Providing and placing in position filters of 40 mm diameter G.I. pipe with brass meter 57.00 960.30 54,737.10 -

strainer of approved quality.

206 NS-40 Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible meter 116.00 110.00 - 12,760.00

Submercible copper cable approved make of following Size. (b) 3 Core x 2.5 Sq.

207 NS-41 Supplying and erecting Kirloskar 1 HP single Phase 100 mm Borewell Nos 2.00 13475.01 - 26,950.02

Submersible Monobloc Pump, KDS 128+, 1 HP, Single Phase, 210 Volts, Size

32mm X 25mm MOTOR bearing ISI mark and manufacture as per IS 8034/1989 to

give the run for pumpset and motor for two hours and one year guarantee

alongwith ISI certificate including cost of all necessary accessories with starter

and 32 mm dia outlet connection etc. complete. Kirloskar or equivalent

209 NS-42 Description:- Pantry cabinetry lower carcass-upplying, and placing in position of sqft 1000.00 2948.00 - 29,48,000.00

pantry cabinets as per design approved and space avilable. a) Bottom carcass:

made of 18mm thick Marine or equivalent ply with both side pasted with 0.8

mm thick laminate of fabric or jute light colour as per approval of engineer

incharge. Exposed edges to be wrapped with machine glued only edge banding

tape of matching colours. Thickness of tape shall not be less than 0.8 mm with

proper edging and trimming of the corners. Back ply to be made in 6mm thick ply

of Marine quality with the same lining laminate of 0.8 mm thick of same colour

and texture as of boxes material. This ply shall be secured in the box with groove

method and no screws are used to fix the ply. All ply boxes to be fixed with rust

proof screws only. No nails shall be used to fix the boxes. Size of carcass

D560x700H. length to be determined as per site. b) Shutters to be made with

Merino or equialent high gloss meister finish or Merino high gloss finish 1 mm

thick laminate/ high gloss acrylic with 2mm thick edge banding tape of same

colour as of front colour, with bak laminate to be matching to carcass shade

210 NS-43 Description:- Pantry Cabinetry Upper carecass-Upper Carcass: storage above sqft 580.000 2400.00 13,92,000.00

cove counter: Shall be made of 18mm thick marine ply with both side pasted

with 0.8 mm thick laminate of fabric or jute light colour as per approval of

engineer incharge. Shutters to be made with merino or equivalent high gloss

mister finish or Merino high gloss finish 1mm thick laminate/ high gloss acrylic

with 2mm thick edge banding tape of same colour as of front colour, with back

laminate to be matching to carcass shade laminate. Size shall vary as per

requirement of design. Expose edges to be wrapped with machine glued only

edge banding tape of matching colours. All exposed surface of carcass to be

fiished with similar material as of shutters, (Sides). Thickness of tape shall not be

less than 0.8 mm thick of same colour and texture as of boxes material. This ply

shall be secured in the box with groove method and no screws are used to dix

the ply. All ply boxes to be fixed with rust proff screws only. No nails shall be

used to fix the boxes. Size of carcass D305x770H. length to be be determined as

211 NS-44 Supply and Fixing of Factory made wardrobe in HDHMR Boad of thickness 18 mm meter 1607.00 2800.00 - 44,99,600.00

for carcass and 25 mm thick for shutter and having 8 mm ply both side laminated

with 0.8 mm thick laminate. Inner side of carcass shall be provided with 1mm

thick of fabric or jute light color laminates on innner side and 1.5m thickness

High gloss, Anti scratch Acrylic laminates on all visible side with 2 mm thick

macthing colour edge binding tap machine glued. Dept of wardrobe shall be 600

mm with drawers as per drawings and approved design. Hinges should of soft

closing type, sensor light should be provided. (Refer Technical speficification for

detail). Front area of shutter shall be measured for payment

212 CIRCUIT POINT WIRING

1.1) Wiring for light point/ fan point/exhaust fan point/call bell point with 1.5 sq.

mm FRLS PVC insulated copper conductor single core cable in

surface/recessed medium class PVC conduit, with modular switch, modular

plate, suitable GI box and earthing the point with 1.5 sq. mm. FRLS PVC

insulated copper conductor single core cable etc as required.

a) 1.10.3 Group-C (Primary point ) Point 256.00 1467 375552 -

1.2) Wiring for group controlled (looping) light point /fan point / exhaust fan 0 -

point/call bell point (without independent switch etc) with 1.5 sqmm FRLS

1.55 PVC insulated copper conductor cable in surface/recessed PVC conduit and

earthing the point with 1.5sqmm FRLS PVC insulated copper conductor single

core cable etc.as required.

a) 1.55.3 Group-C (looping point ) Point 592.00 858 507936 -

1 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper 31240 -

conductor single core cable in surface / recessed medium class PVC conduit, 2

1.11 way modular switch, modular plate, suitable GI box and earthing the point Point 20.00 1562

with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as

1 Supplying and fixing suitable size GI box with modular plate and cover in front 81090 -

on surface or in recess, including providing and fixing 3 pin 5/6 amps modular

1.31 socket outlet and 5/6 amps modular switch, connection etc. as required. (For Each 170.00 477

light plugs to be used in non residential buildings).

2 Supplying and fixing suitable size GI box with modular plate and cover in front 132436 -

on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps

modular socket outlet and 15/16 amps modular switch, connection etc. as

2 Supplying & fixing suitable size GI box wih modular plate and cover in front 40712 -

on surface or in recess including providing and fixing 25 A modular socket

outlet and 25 A modular SP MCB, "C" curve including connections, painting

etc. as required.

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

2 Wiring for circuit/ submain wiring along with earth wire with the following 0 -

1.14 sizes of FRLS PVC insulated copper conductor, single core cable in surface/

recessed medium class PVC conduit as required

b) 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire For Light Circuit Point Metre 1,280.00 275 352000 -

c) 1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire For Power Circuit Point Metre 850.00 334 283900 -

f) 4 X 10 sq. mm + 2 X 10 sq. mm earth wire For Submain Wire / Cable of DB 221100 -

CABLE TRAYS AND ACESSERIES :

2 Supplying and installing following size of perforated pre-painted M.S. cable

trays with perforation not more than 17.5%, in convenient sections, joined

with connectors, suspended from the ceiling with M.S. suspenders including

bolts & nuts, painting suspenders etc as required.

a) 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Metre 80.00 543.00 43440 -

b) 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 70.00 604.00 42280 -

2 Supplying and installing following size of perforated pre-painted M.S. cable 0 -

trays bends with perforation not more than 17.5%, joined with connectors,

suspended from the ceiling with M.S. suspenders including bolts & nuts,

painting suspenders etc as required.

a) 4.2.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 868.00 69440 -

b) 4.2.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,018.00 71260 -

2 Supplying and installing following size of perforated pre-painted M.S. cable 0 -

trays reducers with perforation not more than 17.5%, joined with connectors,

suspended from the ceiling with M.S. suspenders including bolts & nuts,

painting suspenders etc as required.

a) 4.3.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 1,003.00 80240 -

b) 4.3.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,186.00 83020 -

2 Supplying and installing following size of perforated pre-painted M.S. cable 0 -

trays Tee’s with perforation not more than 17.5%, joined with connectors,

suspended from the ceiling with M.S. suspenders including bolts & nuts,

painting suspenders etc as required.

a) 4.4.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 1,139.00 91120 -

b) 4.4.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,356.00 94920 -

3 Supplying and installing following size of perforated pre-painted M.S. cable 0 -

trays cross members with perforation not more than 17.5%, joined with

connectors, suspended from the ceiling with M.S. suspenders including bolts

& nuts, painting suspenders etc as required.

a) 4.5.1 100 mm width X 50 mm depth X 1.6 mm thickness Each 80.00 1,003.00 80240 -

b) 4.5.2 150 mm width X 50 mm depth X 1.6 mm thickness Each 70.00 1,186.00 83020 -

EARTHING INSTALLATION

5 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including 59776 -

accessories, and providing masonary enclosure with cover plate having

locking arrangement and watering pipe 2.7 metre long etc. (but without

charcoal/ coke and salt ) as required.

5 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for 9296 -

connections etc. as required.

5 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for 16904 -

connections etc. as required.

5 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for 1952 -

connections etc. as required.

6 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop 336 -

5.18 earthing along with existing surface/ recessed conduit/submain wiring/ cable RM 8.00 42.00

DISTRIBUTION BOARDS

3 Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with

2.4 tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

3 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, “C” curve, 0 -

miniature circuit breaker suitable for inductive load of following poles in the

existing MCB DB complete with onnections, testing and commissioning etc. as

3 Supplying and fixing following rating, four pole, (three phase and neutral), 0 -

415 volts, residual current circuit breaker (RCCB), having a sensitivity current

30 mA in the existing MCB DB complete with connections, testing and

commissioning etc. as required.

3 Supplying and fixing following rating, four pole, 415 volts, isolator in the 0 -

2.13 existing MCB DB complete with connections, testing and commissioning etc.

4 Supplying and fixing Single Pole Blanking Plate in the existing MCB DB 20680 -

complete Etc. as required.

CONDUITING WIRING AND CABLING FOR TELEPHONE / TV NETWORK

4 Supplying and fixing of following sizes of medium class PVC conduit along

1.21. with accessories in surface/recess including cutting the wall and making good

the same in case of recessed conduit as required.

4 Supply, fixing, connecting and testing of elephone/computer/TV modular 0 -

sockets modular plate anodised MS box and blanking late in surface/recessed

including connectionetc as required.

a) RJ-11 telephone socket two line with shutter 32424 -

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

b) T.V. CO-axial cable socket outlets of one point 26656 -

c) M.R RJ-45 face plate( computer line) with shutter DN-460 Each 56.00 500 0 28,000.00

4 Providing, fixing connecting and testing of solder less telephone Tag block of 0 -

following capacity ties as required in suitable size of m.s. hinged lockable

cover box duly painted etc. as required of Krone type.

a) M.R 10 pair Tele Tag Blk Each 2.00 7,500 0 15,000.00

4 Providing, fixing connecting and testing of solder less Television Junction Box 0 -

of following capacity ties as required in suitable size of m.s. hinged lockable

cover box duly painted etc. as required of Krone type.

a) M.R 2 pair T.V Junction Box. Each 112.00 2800 0 3,13,600.00

5 Supplying drawing, connecting and testing of 0.61mm dia annealed copper 0 -

conductor PVC insulated PVC sheathed telephone Wire/cables in Existing PVC

conduit or a racks as required.

a) 1.18.2 2 pair Telephone cable. (0.61sq mm) RM 336.00 38 12768 -

5 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper 15792 -

conductor PE insulated, shielded with fine tinned copper braid and protected

with PVC sheath in the existing surface/ recessed steel/ PVC conduit as

5 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ 22344 -

recessed steel/ PVC conduit as required.

5 Supplying and fixing metal box of following sizes (nominal size) on surface or 0 -

1.22 in reces with suitable size of phenolic laminated sheet cover in front including

painting etc as required.

6 Supply, fitting, wiring, testing and commissioning of 40 W 2X2 RECESS 0 -

MR MOUNTED LED LIGHT all accessories as required. (Wipro Item Model Number Each - 7200

6 Supply ,fixing , testing and commissioning of 10 W LED CEILING ROUND 0 74,800.00

MR Each 88.00 850

LIGHT all accessories as required.

6 Supply ,fixing , testing and commissioning of20 W LED CEILING TUBE LIGHT 0 1,58,400.00

all accessories as required.

6 Supply ,fixing , testing and commissioning of EXHAUST FAN. all accessories as 0 84,000.00

7 Supply ,fixing , testing and commissioning of 15W CEILING LIGHT. all 0 8,20,000.00

accessories as required.

7 Supply ,fixing , testing and commissioning of 12W CFL CEILING LIGHT. all 0 2,20,800.00

accessories as required.

7 Supply ,fixing , testing and commissioning of MIRROR LIGHT. all accessories as 0 34,000.00

MR Each 40.00 850

7 Supply ,fixing , testing and commissioning of CEILING FAN (1200MM ) all 0 1,80,000.00

accessories as required.

Cable, Mains and sub mains

Cable jointing kit for 11 KV (Earthed) grade cable for indoor termination cold

shrink type joint complete with jointing material and accessories suitable for 3

core XLPE armoured aluminium conductor cable of size 50 sqmm to 95qmm

Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

8 Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed

aluminium conductor armoured cables as per specification in existing trenches,

cable trays, ducts over bed of sand, clamped includes anchor fastners wall with

suitable clamps, saddles fixing bolts including connecting testing and

a.) M.R 3.5 core 70 sq. mm For External Lighting Panel RM 700.00 720.00 0 5,04,000.00

8 Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

7 Supply, installation, testing and commissioning of DVR-20-CH, 400/480fps 0 2,70,000.00

display, 400f/480ps recording, H.264, Recording @704x480 (100/120ips)/

704x240 (200/240ips)/ 352x240 (400/480ips), 8Audio In/ 1 Out, 16 Alarm In, 4

Relay Out, Network Port available for Remote View S/W with transmission

up to 120 IPS @ 352x288 PAL, along with 3 TB HDD, complete all as specified

with 230VAC power supply complete in all respects as per specifications as

per engineer in charge.

7 Supply, installation, testing and commissioning of High Resolution 32 inch 0 85,000.00

LCD colour TV monitor with on screen adjustment menu, durable metal

cabinet etc. complete in all respects as per specifications as per engineer in

7 Supply, installation, testing and commissioning of IR & IP Based dome type 0 3,31,200.00

indoor coloured fixed camera with of 1/3" CCD,540 TVL, Sensitivity @ 30 IRE:

Color 0.5Lx/Night Sense 0.18 Lx, AWB / BLC / AGC /Auto Black, 2.6 to 6 mm

vari-focal lens Auto Iris, 12VDC/24VAC for indoor application, complete in all

respects as per specifications as per engineer in charge.

7 Supply, drawing, installation, testing and commissioning of Video co-axial 0 27,600.00

M.R cable RG 11 in the existing surface / recessed steel/PVC conduit as required. RM 690.00 40

8 Supply, drawing, installation, testing and commissioning of armoured video 0 32,200.00

M.R co-axial cable RG 11 including trenching, excavation and backfilling as RM 460.00 70

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

8 PVC, HDPE PIPES & PVC FLEXIBLE PIPES:: Supply & erection of PVC pipes & 0 -

HDPE pipes (fire retardant) for wiring purposes including bends, inspection

boxes etc., where necessary including other petty material as per PWD

General Specifications 2010:-

Heavy gauge PVC conduit pipe 20mm dia. (ISI marked 2mm thick) Flushed 0 14,720.00

8 Supply and drawing of following sizes of PVC insulated copper conductor 0 -

M.R single core FRLS cable in the existing surface / recessed steel/PVC conduit as

7.10. Supply, drawing, installation, testing and commissioning of PVC insulated and 0 22,500.00

PVC sheathed Instrumentation cable with electrolytic grade annealed bare

M.R flexible copper conductor shielded cable 2 core 16/0.2mm. cable in the RM 300.00 75

existing surface / recessed PVC/steel conduit as required.

7.11. Supply and laying of RG 59/RG 6 tinned copper co-axial cable with polythene 0 10,500.00

M.R insulation. RG 6 only in case of distance between camera and DVR RM 300.00 35

ELECTRICAL FLOOR PANEL

Supply, installation, testing and commissioning of following M.V. cubicle type -

totally enclosed, free standing type, dust, damp and vermin proof,

Distribution Board/Panel complete with busbars, M.V. danger notice plate,

MR interconnections with suitable capacity aluminium leads/ solid aluminium

strips/rods, connection of incoming and outgoing cables with thimbles,

powder coat painted and having following incoming and outgoing

switchgears complete as required.

a.) INCOMER: -

1 No. of 160 Amp 4P MCCB of 35 kA Breaking capacity with On Indicating -

Lamp with 2A SP MCB back-up.

Coloured (Red, Yellow, Blue) phase indicating lamp - 1 set -

(0 - 160 A) CT operated Ammeter with selector switch & 3 nos. CTs ratio -

160/5A ,15VA burden & accuracy class of 1.0 - 1 set

0-500 V Voltmeter with selector switch - 1 set -

b.) BUSBARS: -

200 Amp TPN Aluminium busbars -

c.) OUTGOING: -

8 Nos. 63 Amp DP MCB, with phase indicating lamps. -

2 Nos. 63 Amp DP MCB, SPARE. -

ELECTRICAL METER PANEL describe as above Set 2.00 3,36,300.00 6,72,600.00

ELECTRICAL FEEDER PILLAR PANEL

8.1) M.R ELECTRICAL FEEDER PILLAR PANEL

1 No. 150 Amps FP MCCB with125 A changeover switch with following

VAF digital electronic meter with inbuilt selector switch and 150/5 Amps suitable

VA, CL 1 CTs . -1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's -3 Set

250 Amps TPN Aluminium bars with heat coloured shrinkable insulation sleeve -

63 Amps FP MCB - 10 No.

40 Amps FP MCB - 02 No.

32 Amps FP MCB - 02 No.

d) 63 Amps FP MCB - 02 No.

40 Amps FP MCB - 01 No.

i. All MCCB's shall be of 25 KA (Ics) breaking capacity.

ii All MCB's shall be of 10 KA breaking capacity.

ELECTRICAL FEEDER PILLAR PANEL described as above Set 2.00 2,35,000.00 0 4,70,000.00

MAIN LT PANEL & MAIN DISTRIBUTION PANEL

5 Design, fabrication, assembling, wiring, testing, supply, forwarding to site,

unloading, shifting to location, inspection, installation, testing and

commissioning of DG & Transformer Changeover Panel cum Main LT Panel, Main

distribution panels/ sub-distribution panels and capacitor panel, fabricated out

of 14 gauge CRCA sheet steel in cubicle formation, compartmentalized, from 3b

consutruction, free standing floor mounted, dust and vermin proof with

reinforcement of suitable size angle iron, channel, `T’ sections and/ or flats

wherever necessary. 16 gauge CRCA sheet steel shall be used for final

distribution panels. 3 mm thick cable gland plates shall be provided on top as

well as at the bottom of the panels. Panels shall be treated with all anticorrosive

process before powder coating as per specifications and final approved shade. 2

No. earthing terminals shall be provided for all distrtibution panels. Panels shall

be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall

also be provided in case of large panels. Approval shall be taken for each panel in

the form of shop drawings before fabrication.

Galvanised hardwares with zinc passivation shall be used in fabrication of panels.

DG & TRANSFORMER CHANGEOVER CUM MIAN LT PANEL.

a) DG Incoming Air Circuit Breaker from 62.5 kVA DG set - 1

250 amps 4 pole electrically operated manually draw out type Moulded circuit

breaker with microprocessor release unit , for short circuit, over current and

earth fault protection with adjustable setting as per specification and with

following accessories :

i. Digital energy meter with Maximum demand indicator (conzerve – EM 6400 or

equivalent) of accuracy class-I, with 3 Nos. 250/5 amps 15VA CTs.

ii. Phase sequence relay shall be protected by 2 Amps TP MCB - 1 Set

iii. Phase indicating light shall be protected by 2 Amps MCB’s. - 3 Sets

iv. Battery charger with voltmeter of range 0-50 volts and ammeter of range 0-50

amps for trickle and boost charging.

v. Breaker ON / OFF / TRIP indicating lights with control MCB’s. - 1 Set

vi 24 V DC Shunt trip coil. - 1 Set

vii 240 V under voltage release. - 1 Set

viii. Breaker control switch - 1 Set

ix Excitor field DC voltmeter and ammeter.

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

x. Emergency stop push button.

xi. Selector switch for Auto / Manual / Test

xii. Selector switch for engine control OFF/ON.

xiii. Five push buttons – start, stop, reset, test and accept.

xiv. Three indicating lamps “load on set’, ‘Load on Mains’ and “ Set fail to start’.

xv. 12 Window alarm annunciators panel with hooter, push buttons, aux. Contactors

etc as required as per specification.

xvi. Suitable rating battery charger as per specifications

xvii. Temperature scanner (Messi Bus/Procon)

xviii. Auxiliary contacts required for necessary interlocking of breakers.

b) Incoming Air Circuit Breaker from 50 kVA Transformer-1

250 amps 4 pole electrically operated manually draw out type Moudule circuit

breaker with microprocessor release unit, for short circuit, over current and

earth fault protection with adjustable setting as per specification and with

following accessories :

Digital load manager (conzerve – EM 6400 with RS-485 or equivalent) of accuracy

class-I with 2 No. 250/5 amps 15VA CTs.

Phase indicating light shall be protected by 2 amps MCB’s- 3 Set

Three Phase Under voltage relay (27) - 1 Set

Three Phase Over voltage relay (59) - 1 Set

Breaker ON/ OFF/ TRIP indicating lights with control MCB’s- 1 Set

24 V DC Shunt trip coil. - 1 Set

240 V AC under voltage release. - 1 Set

Auto-manual / test selector / switch - 1 Set

Breaker control switch - 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

Three phase Voltage sensor relay shall be protected by 2 amps TP MCB’s, 1 Set

Transient voltage surge supressor with suitable contactor shall be protected by 2

amps TP MCB’s. - 1 Set

Digital voltmeter with inbuilt selector switch- 1 set

500 A TPN electrolytic Al bus bar with heat shrinkable insulation sleeve

250 Amps 4 Pole MCCB - 6 No.

200 Amps 4 Pole MCCB - 7 No.

150 Amps 4 Pole MCCB - 5 No.

100 Amps 4 Pole MCCB - 6 No.

63 Amps 4 Pole MCCB - 5 No.

150 Amps 4 Pole MCCB - 3No. Spare

100 Amps 4 Pole MCCB - 2 No. Spare

e) Bus Coupler

500 amps 4 pole ACB, with ON/ OFF/ TRIP indicating lamps with microprocessor

release unit, etc complete as per specs.

All outgoing feeders shall have suitable range of followings:

i. All breakers shall be electrically interlocked as per schematic diagram.

ii. All ACB’s/ MCCB’s shall be suitable for 35 KA breaking capacity.

iii. PLC for load management and supervision.

v. Three phase indicating lamps shall be protected by 6 amps SP MCBs.

vi. 1 No. 1000/800/ 5, 15 VA dual ratio CT’s shall be provided for APFCR on

transformer's incomer.

vii. All outgoing feeders shall be provided with built-in short circuit & earth fault

viii. All outgoing shall have dual Electronic energy meter (EM-6438 with RS-485 or

equivalent) with required number of CT's.

ix. Wiring and supply, installation of space heater, humidistat and control MCB’s

shall be provided for all vertical sections.

x. Suitable danger board shall be provided.

xi. All bus bar section/ backside panels shall have pad locking facility and hinged

xii. 9 W fitting with CFL lamp, switch shall be provided in each vertical section.

xiii. Incoming breakers shall have suitable provision for busduct connection..

xiv All Electronic Energy meter shall be pre wired for BMS connection upto central

point within the panel with sheilded cable.

M. R DG & Transformer Changeover Panel as described above. Set 2.00 9,43,000.00 0 18,86,000.00

5.2) M.R WATER SUPPLY PANEL

1 No. 150 Amps TPN MCCB with125 A changeover switch with following

VAF digital electronic meter with inbuilt selector switch and 150/5 Amps suitable

VA, CL 1 CTs . -1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's -3 Set

250 Amps TPN Aluminium bars with heat coloured shrinkable insulation sleeve -

32 Amps TP MCB - 2 No.

25 Amps TP MCB - 6 No.

20 Amps TP MCB - 2 No.

20 Amps FP MCB - 1 No.

3 Amps 4P MCB - 3 No.

i. All MCCB's shall be of 25 KA (Ics) breaking capacity.

ii All MCB's shall be of 10 KA breaking capacity.

WATER SUPPLY PANEL described as above Set 2.00 3,26,818.00 0 6,53,636.00

5.3) M.R FEEDER PILLAR PANEL FOR EXTERNAL LIGHTING.

Supply, installation, testing and commissioning of cubicle type totally enclosed

free standing, dust free, damp and vermin proof and water proof outdoor (IP 55)

Feeder pillar fabricated out of 2mm thick CRCA sheet duly powder coated and

including supply & fixing the following items and interconnections, wiring with

suitable size wires/ cables and including all civil works like excavation, PCC, brick

work pedestal, plastering, refilling etc. and as per specifications as required.

1 No. 200 Amp four pole Moulded Case Circuit Breaker (Ics value 25 KA)

300 Amp TPN busbars of high conductivity electrolytic quality aluminium alloy.

INSTRUMENTS & ACCESSORIES

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

1 No. 96x96 analogue type Voltmeter suitable range for 3 phase, 4 wire

operation with LED display and selector switch withcontrolled by 3 sets of 2Amp

1 No.96x96 analogue typeAmmeter of suitable range ( 0 to 63Amp), for 3 phase

4 wire operation with LED display and selector switch

3 Nos of LED type phase indicating lamps (RYB) with controlled by 2Amp MCB .

1 No.6A, 2 pole Auto/OFF/Manual (2 way with OFF) selector switch.

2 Nos. of push button actuator

Outgoing 1 (6 PM - 6 AM )

TPN DB 6 No. 10 amps SP MCB per phase as outgoing with 3 No. 40 amps DP

RCCB of 30 mA leakage current plus 1 No. 40 amps TP Contactor, push button etc

controlled through 0-24 hour timer, photo sensor and 1 No. 40 amps 4 pole MCB

Outgoing 2 ( 6 PM - 11.55 PM)

TPN DB 6 No. 10 amps SP MCB per phase as outgoing with 3 No. 40 amps DP

RCCB of 30 mA leakage current plus 1 No. 40 amps TP Contactor, push button etc

controlled through 0-24 hour timer, photo sensor and 1 No. 40 amps 4 pole MCB

Fidder pillar as discribed above Set 2.00 38,856.00 0 77,712.00

5.4) M.R Design, fabrication, assembling, wiring, supply, installation, testing and

commissioning of Automatic control panels with mixed die electric type

capacitors, fabricated out of 14 gauge CRCA sheet steel in cubicle

compartmentised, 3b modular construction, free standing, floor mounted, dust

and vermin proof with reinforcement of suitable size, angle iron, channel, `T’

sections and/ or flats wherever necessary. Cable gland plates shall be provided

on top the panels. Panels shall be treated with all anticorrosive process before

powder coating as per specifications and final approved shade. 2 No. earthing

terminals shall be provided for all distribution panels. Panels shall be suitable for

415V, 3 phase, 4 wire, 50 HZ supply system. Lifting hooks shall also be provided

in case of large panels. Approval shall be taken for each panel in the form of shop

drawings before fabrication. Galvanized hardwares with zinc passivation shall be

used in fabrication of panels.

50 KVAR CAPACITOR AUTOMATIC CONTROL PANEL

150 amps TPN manually operated fully drawout type air circuit breaker as per

specification and with following accessories:

96 x 96 mm sq. 0-500 Volt digital voltmeter with selector switch

Phase indicating light shall be protected by 2 Amps SP MCB’s -3 Set

Power factor compensating relay (including power factor meter) in 10 steps for

automatic cut off or add on capacitor units to keep the power factor at 0.98 with

variation of loads. All associated auxiliary contactors/ relays/ timer/ auto manual

selector switches to be provided - 1 Set.

200 amps TPN Aluminium bus bars with coloured heat Shrinkable insulated

sleeves. - 1 set

c) Outgoings - I :

40 amps TPN MCB - 8 Set

Outgoing feeders consisting of following accessories.

80 amps or capacitor duty 525 volts 50 Hz contactors - 2 Sets

“ON” /”OFF” push buttons and indicating lamps - 2 Sets.

12.5 kVAr, 525 volts capacitor unit with detune filters as specified - 2 Sets.

d) Outgoings - II :

63 amps TPN MCB - 1 Set

Outgoing feeders consisting of following accessories.

80 amps or capacitor duty 525 volts 50Hz contactors - 1 Sets

“ON” /”OFF” push buttons and indicating lamps -1 Sets

25 kVAr, 525 volts capacitor unit with detune filters as specified - 1 Sets.

All MCCB’s shall be of 35 kA breaking capacity.

i. Fast response time of ‘ON’ capacitors 40-60 miliseconds.

ii. Necessary control and firing card with proper wiring and lugs of the required

rating to be provided.

iii. Heavy duty exhaust fans to be provided for cooling Thyristors

iv. LED indication for number of capacitor banks ‘ON’.

v. LED indication of Power Factor lagging or leading.

vi. The APFC system shall be provided with following :

a. Over voltage.

b. Voltage imbalance.

c. Over temperature-system should be in standby mode

& automatically restart after above condition restored.

d. Earth leakage.

e. 7% value reactors with iron core.

Capacitor automatic control panel (500 kVA) as described above. Set 2.00 5,11,905.00 0 10,23,810.00

SUPPLY AND INSTALLATION OF DG SET WITH ACCESSORIES

4 Supply, installation, testing & commissioning of 62.5 KVA (Prime rated) diesel 0 11,56,420.00

generating set in acoustic enclosure, heat exchanger type alongwith day oil fuel

tank including first fill of diesel with fuel piping to and from DG set including AMF

Panel, vibration mounts, base frame, hardware Batteries, Engine control panel

M.R with accessories first fill of lube oil silencer with installation, flexible connection Sets 2.00 5,78,210.00

bellow / expansion joints etc.. complete and with all associated equipment /

work , cable / Bus bar terminal boxes and suitable mounting arrangement for

mounting of differntial CT,s protection as per specifications.

4 Providing, fixing & installing MS exhaust pipe 6 mm thk and all fixing accessories

and hardwares. The exhaust pipes shall be Painted with high temperature paint

M.R & insulated with 75 mm thick mineral wool (density 150 kg/m3) insulation

wrapped in chicken mesh and clad with 26 gauge aluminium sheet including all

MS epoxy painted support structural as required.

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

Supply, Installation, Testing and Commissioning of fully automatic 8 Nos.

Passanger (Minimum) Elevator, in lift shaft of dimensions 1500mm (W) x

2100mm (D), 544 Kg., with variable voltage variable frequency drive having

a speed of 1.5 metre/ sec and travel height of 19.40 m (approx.) with 6 Stops

and Microprocessor based control suitable for operation on 415 V, 50 Hz, 3

phase A.C. electric Supplying as required.

1.Type of machine Gearless, machine room less

2.Capacity 544 kg

3. Number of Passengers 8 Nos. (minimum)

4.Speed 1.5 mps.

5.No of landing 6 Landings(B+S+3+Terrrace Floor)

6.Number of openings 6 on the same side.

7.Travel approx 19.40 meter

8.Power Supplying 415V/240V, 50HZ 8.Acceptable voltage

Fluctuation +10 to -20%

9.Rate of Accelaration / 0.6-1.5 (adjustable at site) decelration

10.Jerk (m/sec.sq) 0.7-1.5 (adjustable at site)

11.Vibration in car horizontal 20/18 MG maximum

vertical 20/18MG maximum

12.Noise level in car 48dbA max.

13. Door noise level while closing and 52dbA max. opening at a distance of

14. Type of Drive: Variable Voltage Frequency Drive V3F.

15. Location of Machine Room: Machine room less

16. Indicators car & landings: 7 Segment 25mm digital direction and

indicators in car and at all landings.

17. Special features/other features : Automatic Rescue Device with

dry maintenance free batteries

18. Call register type KDS-50 Micro pushbutton for Car and landing.

19. 3-Way Intercom

20. Manual Cranking operation

21. Integral shaft for gear and motor

22. Emergency Stop Button

23. CVT/Built Voltage Stablizer (Constant Voltage Transformer)

24. Pit ladder and ballustrade

25. Flooring : Provision for Granite flooring with 19mm recess.

26. Emergency cabin lighting and alarm.

27. FRD/Fire Man Drive (Fire Rescue Device)

28. Controls: Resolve Micro Processor based simplex full collective

control with or without attendant operation.

29. Door Safety : PANA 40-Full ray curtain for car door safety.

30. Load weighing device with indicator & bypass function.

31. Lift Announcement System (LAS)

32. Safety gears & over speed governer

33. Infra red door safety device

34. Civil works: All minor civil works such as scaffolding, making

holes, grouting, concreting etc.

35. Provision for connectivity of CCTV and other features complete in all respect

PASSENGER ELEVATORS-P1 as desctribed above Set 2 20,38,860.00 0 4077720

SUB HEAD -I: PUPM EQUIPMENT & ACCESSORIES IN TERRACE

Supplying, installation, testing and commissioning of electric driven terrace pump

18.4 suitable for automatic operation and consisting of following, complete in all 0 -

respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casing pump of cast iron body &

a) bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 0 -

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415

volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure,

horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts

etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads

Providing laying, testing and commissioning of class 'C' heavy duty MS pipe

confirming to IS 3589/1239 including fittings like elbows, tees, flanges, reducer,

jointing with nuts bolts, gasket and welding etc. and supports, as required and 0 -

painting with tow or more coats of synthetic enamel paiing of required shade

complet as directed by Engineer-iin-charge.

Supplying, fixing, testing and commissioning of butterfly valve PN 1.6, with

18.11 Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, 0 -

gaskets, confirming to IS 13095, of following sizes as required.

Providing, installation, testing and commissioning of dual plate non-return valve of

18.14 following sizes confirming to IS 5312 complete with rubber gasket, GI bolts, nuts, 0 -

washers etc. as required.

Providing & fixing 100mm dia bourden type, Stainless steel dial type pressure

MR Gauge (0 - 16 Kg ) range, 3 / 8 " BSP bottom entry on Pump Delivery Line Each 2 859.00 0 1,718.00

complete with Ball valve

SUB HEAD -III: FIRE EXTINGUISHERS

Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded

M.S. cylindrical body, squeeze lever discharge valve fitted with pressure indicating

guage internal discharge tube 30 cms long high pressure discharge hose, discharge 0 -

nozzle, suspension bracket conforming to ID:15683 finished externally with red

enamel paint and fixed to wall with brackets complete with internal charge.

Digitally signed by GOUTAM

Construction of Housing Dwelling Units for SIDBI at Plot no. C-40 & C-82 at Inderpuri, Delhi

BILL OF QUANTITY

S.NO DSR-2023 SUB-HEAD (ITEM WISE) UNIT TOTAL DSR -2023 NS Amount Amount

QTY DSR-2023 (Non-Schedule)

Providing and fixing of ABC Powder type fire extinguishers consisting of welded

M.S. cylinderical body, squeeze lever discharge valve fitted with pressure

indicating guage internal discharge tube 30 cms long high pressure discharge hose, 0 -

discharge nozzle, suspension bracket conforming to ID:15683 finished externally

with red enamel paint and fixed to wall with brackets complete with internal charge.

SUB HEAD-V : SPRINKLER SYSTEM & PIPING

Providing laying, testing and commissioning of class 'C' heavy duty MS pipe

confirming to IS 3589/1239 including fittings like elbows, tees, flanges, reducer,

1.0) jointing with nuts bolts, gasket and welding etc. and supports, as required and 0 -

painting with tow or more coats of synthetic enamel paiing of required shade

complet as directed by Engineer-iin-charge.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type

sprinklers of rating 68 degree centigrade with required accessories :

1.1) 1.9 Pendent Sprinkler Each 72 484 34848 -

Digitally signed by GOUTAM