EXTENSION OF EXISTING ROOMS OF CANTEEN BLOCK AND OTHER MINOR WORKS AT ELA FARM, OLD-GOA

Amount

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in :All kinds of soil

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Exposed decorative laterite masonry using Patradevi stone of size as specified and laid as directed by architect in cement mortar 1:4 (1 cement : 4 coarse sand)

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in:All works upto plinth level

Making plinth protection 50mm thick of Cement Concrete 1:3:6 (1cement: 3 Coarse Sand: 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry laterite aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size)All works upto plinth level

Centering & shuttering including Strutting, Propping & removal of forms for :Foundations, Footings, Bases for columns

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws.Ornamental grill

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint.In tees, angles, flats and channels

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing & fixing M.S. round holding down with nuts & Washer plates complete.

Providing and fixing in position G.I. hand rail polyster powder coated in external passage, as per approved design shown in drawing including bending hand rail pipe to proper shape in curves with special etc. complete.

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) a)20 mm thick.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqmJet Black

12mm cement plaster 1:3 (1 cement : 3 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Applying priming coat with ready mixed red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for steel work of approved brand & manufacture in all shades on new work to give an even shade.

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth above 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete.c)250 mm nominal size

Extra for providing and fixing prince or equivalent make PVC SWR running outlet with 2 clamps for socketed half round eaves guttersc)250 mm nominal size.

Extra fjor providing and fixing prince or equivalent make PVC SWR 90 deg. Elbow with /without outlet with 2 clamps for socketed half round eaves gutters.c)250 mm nominal size.

Providing&fixinginposition Galvalume/Zincalume flashings, cappings, ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold Rolled Steel 550 MPa yeild Stress ASTM A 446 Grade E) with hot-dip metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and 0.50mm total coated thickness, factory cut at all heights for roof, side & gable cladding complete in all respects with AZ 150 GSM SMP color Coated (20mic exterior coat of Silicon Modified Polyester paint system over 5 mic primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to purlins with no 12x14x55mm mechanically galvanised hex head self drilling screws of the best quality as per AS- 3566 class 3-4 approved, which should be compatible to be used with sheets. with integral washers and EPDM seals etc. Silicon sealant non- hardening neutral cure type shall be applied at all end laps, complete as directed.

Providing&fixinginposition Galvalume/Zincalume flashings, cappings, ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold Rolled Steel 550 MPa yeild Stress ASTM A 446 Grade E) with hot-dip metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and 0.50mm total coated thickness, factory cut at all heights for roof, side & gable cladding complete in all respects with AZ 150 GSM SMP color Coated (20mic exterior coat of Silicon Modified Polyester paint system over 5 mic primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to purlins with no 12x14x55mm mechanically galvanised hex head self drilling screws of the best quality as per AS- 3566 class 3-4 approved, which should be compatible to be used with sheets. with integral washers and EPDM seals etc. Silicon sealant non- hardening neutral cure type shall be applied at all end laps, complete as directed.respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturersrecommendations.The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat ofsurface treatment etc. complete.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete.

Applying breathable, non-reactive, antifungal, and water repellant Silane/ Siloxane chemical as approved by Archaeological Survey of India/ Engineer, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the exposed laterite masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer. (The rate is inclusive of all materials & labours).

Dismantling of existing G.I pipe including disposal of unserviceable material and stacking of serviceable materials .Upto 20 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :32 mm nominal bore

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality :50 mm nominal bore

Providing and fixing ballvalve(brass)of approved quality :High or low pressure with plastic floats:25mm nominal bore

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:110 mm dia

Providing and fixing U.P.V.C. pipe clips (approved make ) for S.W.R. pipes :110mm

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall.SCH-40(blue)/(white)32mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work.SCH-40(blue)/(white)50mm outer dia.

Providing anti – termite treatment to buildings conforming to I.S.S. 6113 part II 1971 (revised) including adopting precautions for health hazards and safety measures as required therein with the cost of all materials, chemicals, plants, equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (The payment will be made on plinth of the building.Post construction

Providing and fixing prefabricated compound gate of G.I. pipes 40 – 50 mm dia (medium) with 12mmM.S. square bars of G.I. pipes grill work as per drawing including providing & fixing locking arrangements, pintals, hold fast embedded in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 granitic or basaltic aggreate 20mm nominal size) including applying priming coat with ready mixed red lead paint and painting 2 or more coats with superior ready mixed paint of approved brand and manufacture in all shades as per direction complete.

Wiring for light point/ fan point/ exhaust fan point/ callbell point with 1.5 sq.mm FRLS PVC insulated copperconductor single core cable in surface steel conduit(medium) with modular switch, modular plates, suitablesize modular GI box of specified Category and earthing thepoint with 1.5 sq.mm FRLS PVC insulated copperconductor single core cable etc. as required.Group C -- with Cat A Modular Accessories

Wiring for 5A /15A plug with 4 x 4 sq.mm FR PVCinsulated copper conductor single core cable in PVCcasing capping alongwith 2 Nos of 4 sq.mm FR PVCinsulated copper conductor single core cable for loopearthing as required.

Wiring for circuit/ submain wiring alongwith earth wirewith the following sizes of FR PVC insulated copperconductor single core cable in the independent PVC casingcapping of appropriate size as required.

Supplying and fixing following modular switch/socket on the existing modular plate and switch boxincluding connections but excluding modular plateetc. as required5/6 A switch Cat A

Supplying and fixing stepped type electronic fanregulator on the existing modular plate switch boxincluding connections but excluding modular plate

Supplying and fixing 3 pin 5 A ceiling rose on theexisting junction box/ wooden block includingconnections etc as required.

Supplying and fixing following size modular PVC boxalongwith modular base and cover plate formodulator switches in recess etc. as required12 Module ) Cat A

Supplying and fixing following size modular PVC boxalongwith modular base and cover plate formodulator switches in recess etc. as required16Module ) Cat A

Supplying and fixing following size modular PVC boxalongwith modular base and cover plate formodulator switches in recess etc. as required18Module ) Cat A

Supplying and fixing extra down rod of 20 cmlength GI pipe 15 cm dia heavy gauge includingpainting etc as required

Supplying and fixing following way SPN sheet steel MCBdistribution board 240 V on surface/ recess completewith tinned copper busbar neutral busbar earth bardinnbar detachable gland plate interconnectionsphosphotized and powder painted including earthingetc. as required (but without MCB/RCCB/Isolator)(a) 4 way single door Cat A

Supplying and fixing B series SP MCB, 240 V, suitablefor lighting and other loads of following poles in theexisting MCB DB complete with connections testing andcommissioning etc as required"

Supply and erecting of 56 inch (1400mmsweep) ceiling fan, double ball bearing type, ,complete with all accessories.

Supplying and fixing surface mounted LED batten-tubes of 22 w jaquar glaze ultra(PC) or equivalent make including labour etc. all complete

RAHUL CONSTRUCTION (BID ID -48881)