SPECIAL REPAIR TO BLDG NO P-7, P-8 and P-61 INCLUDING ADDN ALTN TO BLDG NO T-34 AND PROVN OF PAN WASH AREA UNDER AGE BR DETT-A AND AGE EM OF GE 862 EWS

Amount

Sch 'A' Part-I (B/R works) Demolition of cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness below or above the ground level including removing debris outside from MoD land, complete all as specified and directed. Note:- Concrete thickness includes of PCC, screed, tiles if any found during execution and no claim shall be submitted by contractor in this aspect and no extra cost shall be borne by govt exchequer)

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed.

Demolition and breaking up drain pipe 75/110mm bore (salt glazed stoneware /AC/ PVC pipe including fittings, complete all as specified and directed.

Taking down cement plaster, any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. Note:- No extra cost to be borne by govt exchequer in r/o to any thickness of plaster increased due to overleaping of wall finishes such as tiles/ mosiac for taking down cement plaster.

Taking down chowkhats or frames (without taking off shutters from the frames) exc 1.5 Sqm but n. exc 4.0 Sqm each, complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) n.exc 1.5 Sqm each, complete all as specified and directed.

Dismantling of timber scantling 40 Sqcm and over in section, in any position as in unframed or framed work as in purlin and rafter, complete all as specified and directed.

Dismantling of timber scantling under 40 Sqcm in section, in any position as in unframed or framed work as in purlin and rafter, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4, complete all as specified and directed.

M&L for stone walling of random rubble masonry, uncoursed, well bonded, bedded and soilidly hearted, built in cement mortar 1:6, complete all as specified and directed.

Description all as per srl item No. 11 above but except stone. NOTE: Old stone retrieved from demolition shall be used.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished the surface even and smooth without using extra cement, complete all as specified and directed. Note:- Contractor shall have no claim if plaster is caried out in patches irrespective of any height.

M&L for rendering 15 mm thick in cement mortar 1:4 on other than fair faces of brick work or concrete surfaces, finished the surface even and smooth without using extra cement mixing with water proofing compound as per manufacturer's instructions , complete all as specified and directed. Note:- Rate of WPC shall be included in the quoted rate.

M&L for rendering 10 mm thick in cement mortar 1:3 on ceiling surface, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 on concrete surface of fin facia, chajja, roof projection etc, finished the surface even and smooth without using extra cement over dubbing out average 10mm thick on irregular face, complete all as specified and directed. Note:- Contractor shall have no claim if plaster is caried out in patches irrespetive of any hieght.

M&L for rendering 15 mm thick in cement mortar 1:3 on concrete surfaces of sunken floor, finished the surface even and smooth with neeru finish with using extra cement mixing with water proofing compound as per manufacturer's instructions , complete all as specified and directed. Note:- Rate of WPC shall be included in the quoted rate.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair/other than faces of brick wall or concrete work, finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 20 mm thick in cement mortar 1:6 on stone wall surface (internal surface), finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 20 mm thick in cement mortar 1:4 on stone wall surface (external surface), finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick plain cement concrete, type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection, laid in slope 1:12 from outer edge of the wall, finished even and fair, laid in alternate bays including providing 6mm wide joints throughtout thickness of plinth protection in concrete bays and in between walling and plinth protection, joints filled mastic filling comprising of one part of heated bituminous 85/25 and 3 parts of sand (all by weight), complete all as specified and directed.

M&L for plain cement concrete 1:5:10, type E-2 (using 40 mm graded crushed stone aggregates) as sunken floor filling and mass concrete, complete all as specified and directed.

M&L for bitumen blown any grade, applied hot, two coats to concrete surface at the rate of 1.5 Kg per Sqm per coat, complete all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregates as in sub base of floor, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4, type B-0 using 12.5mm graded crushed stone aggregates as in topping layer or sub base, finishing the surface of concrete topping even and fair without using extra cement, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (premium quality) Square/rectangular, area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 350x250x7mm / 450x350x7mm thick, (premium quality) on vertical surface of wall such as dado, skirting, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:4, complete all as specified and as directed.

M&L for vitrified tiles light shade, coloured (premium quality) 10 mm thick (square/ rectangular) polished, area of each tiles n. exc 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, laid over and including 15 mm thick screed bed in cement mortar 1:4, complete all as specified and directed.

All as per srl item no 29 here-in-before but in skirting including 10 mm thick rendering in cement mortar 1:4, complete all as specified and directed.

S&F for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square, complete all as specified and shown on drwaing in SSR Part-II (2020) directed.

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & shown in drawing mentioned in SSR Part-II 2020, complete all as specified and directed.

S & F of 250 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy (ISI marked), complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 200 mm long of extruded section (ISI marked) ,complete all as specified and directed.

S&F for extruded aluminium alloy handles size 150 mm fabricated type anodised (ISI marked), complete all as specified and directed.

S&F in repair for 75mm long butt hinges medium weight stainless steel (ISI Marked) fixed with screws or, complete all as specified and directed.

S&F for 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n . exc 0.50 sqm in each pane complete after hacking out old broken glass all as specified and directed.

S&F in repair for stainless steel curtain rod of 25mm dia bright finish, fancy type with brackets and end cups etc with PVC rawl plug & steel screws, complete all as specified and directed.

S& F for galvanised statinless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks, or galvinsed wire staples , complete all as specified and directed.

Taking down GI tubing of 15mm dia and connection including cleaning for refixing or removal, complete all as specified and directed.

Taking down GI tubing of 20mm dia and connection including cleaning for refixing or removal, complete all as specified and directed.

M&L for 15 mm bore GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors after taking down GI tubing 15 mm bore and connections, complete all as specifed and directed.

M&L for 20 mm bore GI tubing medium grade with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors after taking down GI tubing 20 mm bore and connections, complete all as specifed and directed.

Fixing only 15 mm bore old GI tubing with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specifed and directed.

Fixing only 15 mm bore old GI tubing with all fittings such as bends, socket, tee, elbow, union, nipple, short pieces and fixed to walls, ceilings or laid in floors, complete all as specifed and directed.

S&F in repair for stainless steel grating 100mm dia, complete all as specifed and directed.

S&F in repair for 15mm bore brass chromium plated wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe, complete all as specified and directed.

S&F in repair for 15mm bore bib tap cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F for 15mm bore bib tap cast copper alloy, chromium plated, long body, fancy type with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair for 15mm bore Stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F for 15mm bore Stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair for 15mm bore angle valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, chromium plated, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair for 75mm bore PVC (SWR) floor trap, plain with grating including connecting to waste pipe and fixing with cement concrete 1:2:4, type B-1, complete all as specifed and directed.

S&F in repair for CP soap dish holder fancy type with chromium plated brass screws and wooden/plastic cleats, complete all as specified and directed

S&F in repair for brass chromium plated toilet paper holder with flat recessed type, fixed to wall with steel screws, complete all as specified and directed.

S&F in repair 15mm health faucet (ABS body) mild steel chromium plated with 1.25 meter long flexible tube and ABS wall hook including making connection and fixed in position, complete all as speicified and directed.

S&F in repair for chromium plated brass shower rose of size 125 mm with swivel joints fixing to steel pipes etc. Complete all as specified and directed.

S&F in repair for brass chromium plated tubular towel rail 20 mm dia "D" type 60 cm long between flange, fixed with steel screws and wooden/plastic cleats, complete all as specifed and directed.

S&F in repair for brass chromium plated towel ring fixed with steel screws and wooden/plastic cleats, complete all as specifed and directed.

S&F in repair for stainless steel peg set of 06 nos hook, fixed with steel screws and wooden/plastic cleats, complete all as specifed and directed.

S&F in repair for glass corner shelf with tempered glass, stainless steel brackets and polished chrome finish rail, complete all as specified and directed by Engr-in-Charge.

S&F in repair for sheet glass shelf assembly consisting 5.5 mm thick, sheet glass shelf 12cm wide with chromium plated bracket guard and rainling 60cm long, complete all as specified and directed.

S&F in repair for viterous china wash down water closet pan, white (pedestal pattern) with P or S trap, fixed in floor with brass screw including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, and inlcuding set of CP jet spray with flexible PVC pipe of superior quality anfd flush pipe, complete all as specified and directed.

S&F in repair for vitreous China water closet (squatt pan) Orrisa pattern 580x440 mm size pan, white, with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to flushing cistern/pipe including trap set in concrete and removing debries from site, complete all as specified and directed.

S&F in repair for 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

S&F in repair for vitreous China urinal half stall type, white (back or corner wall type), complete including providing and fixing plus, bedding urinal against wall in cement morter 1:2 securing urinal to plus with and including 60cm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe including connecting to waste pipet, complete all as specified and directed.

S&F in repair for viterous China water closet pedestal pattern in one piece type of dimention 73cmX36cm74cm including seat cover and gaset, floor mounted, 'P' or 'S' trap, flushing kit, and all necessary fixing arrangements (excluding fixing bolts and flushing cistern and flush pipe), complete all as specified and as directed.

M&L for prepolished coloured chequered cement concrete tiles of size 300x300x25 mm thick set, jointed in neat cement slurry in floor and pointed in white or coloured cement to match the shade of tiles laid over and including 15 mm thick screed bed in cement mortar 1:4 including demolition of old tile, complete all as specified and as directed.

S&F in repair for vitreous China wash basin, white, flat back, size 550x 400mm excluding taps, waste chain and plug and pocelan stopper but including cutting for pinning in ends of brackets including 32mm bore waste coupling brass CP with long screwed shank and fly nut and waste pipe 900mm long, complete all as specified and directed.

S&F for vitreous China wash basin, white, flat back, size 550x 400mm excluding taps, waste chain and plug and pocelan stopper but including cutting for pinning in ends of brackets including 32mm bore waste coupling brass CP with long screwed shank and fly nut and waste pipe 900mm long, complete all as specified and directed.

S&F in repair for 15 mm bore brass chromium plated wash hand basin mixer hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed.

S&F in repair for 32/40mm bore waste coupling chromium plated for Wash hand basin and sink long screwed shank and fly nuts, flange end bedded in red lead cement, complete all as specified and directed.

S&F in repair for PVC waste pipe 32mm dia, 900mm long suitable for wash hand basins and urinals including connecting, complete all as specified and directed.

S&F in repair for 15mm bore Stop valve, 2 in 1, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair for 15mm bore, pillar cock, cast copper alloy, with capstan heads, chromium plated, fancy type, screwd down high pressure , with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed.

S&F for 15mm bore, pillar cock, cast copper alloy, with capstan heads, chromium plated, fancy type, screwd down high pressure , with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, complete all as specified and directed.

S&F in repair for ball valves suitable for 20mm bore iron pipe high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed by Engr-in-Charge.

S&F in repair for PVC connection 15 mm x 450 mm including brass nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F for PVC connection 15 mm x 450 mm including brass nuts at both ends screwed for iron pipe of 15 mm bore, complete all as specified and directed.

S&F for rotational double layered polythylene water storage tank (ISI marked) with float valve, plastic lid cover, double layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball brass valve with union screwed for iron pipe and fixed including dismantling of old water tank, complete all as specifed in SSR part-I and as directed. Note:- The water storage tank shall be ISI marked and weight shall be as per IS specification and engraving IS No.

S&F for rotational moulded polythylene water storage tank (ISI marked) with float valve, plastic lid cover, multy-layered, cylindrical vertical with closed top, hoisted and fixed in position of capacity 1000 ltrs tank and making connections inlcuding suitable GI wash out, over flow, nipple and including 20mm bore ball brass valve with union screwed for iron pipe and fixed, complete all as specifed in SSR part-I and as directed. Note:- The water storage tank shall be ISI marked and weight shall be as per IS specification and engraving IS No.

M&L in repair for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floor/trenches, complete all as specified and directed.

M&L in repair for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with MS clamps, complete all as specified and directed.

M&L for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floor/trenches, complete all as specified and directed.

M&L for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with MS clamps, complete all as specified and directed.

M&L in repair for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in floor/trenches, complete all as specified and directed.

M&L in repair for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with MS clamps, complete all as specified and directed.

S&F in repair for 110 mm bore PVC (SWR) bend of any radius disminishing pieces or tappers (larger bore measures) with or without access door, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75 mm bore PVC (SWR) bend of any radius disminishing pieces or tappers (larger bore measures) with or without access door, complete all as specifed and directed by Engr-in-Charge.

S&F for 75 mm bore PVC (SWR) bend of any radius, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 110mm bore PVC (SWR) branch piece (single Y) equal or unequal with oval access, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75mm bore PVC (SWR) branch piece (single Y) equal or unequal with oval access, complete all as specifed and directed by Engr-in-Charge.

S&F for 75mm bore PVC (SWR) branch piece (single Y) equal or unequal with oval access, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 110mm bore PVC (SWR) branch piece (Double) equal or unequal, ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75mm bore PVC (SWR) branch piece (Double) equal or unequal, ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 110mm bore PVC (SWR) P or S trap jointed with 110mm bore PVC pipe, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 110mm bore PVC (SWR) junction single 'T' equal or unequal, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75mm bore PVC (SWR) junction single 'T' equal or unequal, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75mm bore PVC (SWR) junction double 'T' equal or unequal, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75mm bore PVC (SWR) reducer unequal, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 110mm bore PVC (SWR) reducer unequal, complete all as specifed and directed by Engr-in-Charge.

S&F in repair for 75mm bore PVC (SWR) vent cowl, complete all as specifed and directed by Engr-in-Charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cements base paint over a coat of primer, complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over 1.50mm thick wall care putty, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

M&L for preparation of old decorated brick / concrete plastered / un-plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement base paint , complete all as specified and directed.

M&L for preparation of old decorated brick / concrete plastered / un-plastered surfaces of walls, pillars, cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of oil emulsion distemper, complete all as specified and directed.

M&L for preparation of old steel surface of any description over 10 cm width or girth not and applying one coats of synthetic enamel paint, complete all as specified and as directed by Engr-in-Chagre.

M&L for preparation of old wooden surface of any description over 10 cm width or girth and applying one coats of synthetic enamel paint, complete all as specified and directed.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilivers, shelves, including sup-ports, overhangs etc also splays between floors and beam etc, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L for mild steel TMT bars 5 m dia and over including 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends as in stirrups, spacers and binders including binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for reinforced cement concrete 1:1.5:3, B-1 (Design Mix) (20mm graded crushed stone aggregate) as beams and columns in floors, roofs, landings, balconies,canopies, deck slabs, chajjas and in shelves and the like, complete all as specified and directed

Taking down ceiling boards of any description and thickness including cover fillets, complete all as specified and directed.

S&F for 4mm thick designer ceiling board in ceiling fixed with screw as per manufacturers instructions, laid over and including hot dipped galvanised iron in post grid with 24mm wide T section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33 mm thick galvanised steel sheet of size 24 x 32 x 300 mm spaced at 1200 mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4 mm dia to be fixed by approved rawl plug or hanged with existing truss members. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall flush fittings of 1200 mm long screws Tee with (double stiching) to interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm modules cross tee longer than 600 mm modules to be formed by fittings 600 mm long cross tee, tee perimeter wall angle shall be of 0.45 mm thick galvanised steel of size 19 x 19 mm and 300 mm long of white colour all as per insturctions, complete all as specified and directed.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy brackets framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc. conforming to Fe-410-W (Gde - E-250) quality A complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe-41 W (Gde-E-250) complete all as specified and directed.

M&L for Mild steel screw 12mm bolts and nuts (machine made) with hexagonal or square head at one end and screwed the other with washers of length exc 5 cm and n exc 10 cm, complete all as specified and directed.

S&F for fibre glass reinforced translucent corrugated sheeting with two corrugations side laps fixed with coach screws and washer in roof , walls etc including dismantling existing sheets, complete all as specified and directed.

S&F for pressed steel door frame of size 125x60 mm with one or more rebates including necessary fixing lugs, hinges, lock and strike plate etc including back filling to chowkhats in PCC 1:3:6 type C-1 using 20mm graded stone agregate complete all as specified and directed.

S&F for flush shutter sold core construction with block board core and plywood face panels, commercial type on both sides 35mm thick and covered on both sides with decorative face veneer with lapping / frame to match, complete all as specified and directed.

M&L for 12mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminium frame work including dismantling old particle board, complete all as specified and directed.

S&F for factory made 35 mm thick 2nd class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed.

M&L for Powder coated aluminium frame for doors, windows and ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed. Note : minimum thickness of power coating 50 micron.

S&F for anodised aluminium (minimum thickness of power coating 50 micron) door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, mortice lock, 1 Nos floor door stopper, anodised aluminium snap beading, screws etc, complete all as specified and directed.

S&F for powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 nos), suitable handle (1 no), complete all as specified and directed. Note : minimum thickness of power coating 50 micron

M&L for sheet glass 5.5 mm thick, ordinary quality and fixed with aluminum & rubber beading in square exc 0.5 sqm in each pane, complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of cement base paint after preparation of surface, complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying two coats of distemper oil emulsion over a coat of primer after preparation of surface, complete all as specified and directed.

S&F for solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at wall/ceiling, including 5mm thick PVC sheet fillet of width 35mm for wall/ceiling paneling on PVC/wooden frame as per specification and drawing complete after dismantling of old unserviceble PVC lining, including fillets complete all as specified and directed.

M&L for preparation of new steel surface exc 10 cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed by Engr-in-Chagre.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m in depth in soft/loose soil, for foundation, etc, or for shafts, wells, drain, pipes, laying of cable/pipes, foundation of poles/stays etc n.exc 10 Sqm on plan and getting out, complete, all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick ,complete all as specified and as directed.

Removing excavated material ,not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting poin, complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-2 ,using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm bore SGSW pipe, complete all as specified and directed.

M&L for 150 mm internal dia Salt-Glazed stone ware drain pipes grade 'A' laid in trenches over concrete bedding jointed in cement mortar (1:1) and tested ,complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete, complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide, complete all as specified and directed.

M&L for RCC 1:2:4, type B-1 (nominal mix) (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for 20mm thick granite black or any other colour, of any type of work (table rubbed and polished) as in steps, jambs, pillars, window - cills, cooking platforms, urinal partition and like set in cement mortar 1:4 including pointed in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including grinding and polishing, complete all as specified and directed.

M&L for cutting the existing 20mm tubing for addition or alteration (Each cut to be measured separately) and inserting new GI tee including necessary screwing threading, tail pieces, short pieces, jointing material etc, complete all as specified and directed by Engr-in-Charge.

S&F for gun metal globe or brass gate valve with iron wheel screwed both ends for iron pipe of 20mm bia, complete all as specified and directed.

S&F for sink made out of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe, over all size 495mm x 420mm, bowl size 410mm x 330mmx 160mm including waste pipe 32mm dia 900mm long, complete all as specified and directed.

Surface excavation in soft/loose soil, n.exc 1.5m 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nanital or similar pattern roof coverings, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

M&L for extra over granite or stone walling of any type of stone for hammer dressing to face stones and dressing of face beds with maximum depression on face from straight edge held against the dressed surface n exc 20 mm and joints, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and directed.

M&L formwork to soffits of suspended slabs such as roof slabs, landings and similar work; n exc 200mm thick (Horizontal and sloping) for rough finished surface of concrete, complete all as specified and directed.

M&L formwork to sides of concrete foundation, footing, bases of colums, raft & raft beams, sides and soffits (if any) of foundation and plinth beam and similar work, in rough finished flat surface of concrete, complete all as specified and directed.

M&L formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surface of concrete, complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4, type B-1, (nominal mix), (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns and the like, complete all as specified and directed

M&L for reinforced cement concrete 1:2:4, type B-1, ( nominal mix) (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintel over 1.5 mtr span, complete all as specified and directed

M&L for reinforced cement concrete 1:2:4, type B-1, (nominal mix), (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, post, struts and the like, complete all as specified and directed

M&L for 75mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregates as in sub base of floor, complete all as specified and directed.

Sch 'A' Part-II (E/M works) Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete, including all fittings such as switches, ceiling roses, pendants, regulators, sockets etc.) removing material from the site and making good the disturbed surfaces of walls, floor or ceiling etc. to match with existing specifications, complete all as specified and directed.

M&L for point wiring for one light point/fan point controlled by one-one way switch with 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor unsheathed in and including PVC conduit pipe not less than 20mm dia concealed in wall /ceiling surface complete with all acessories including pressed steel terminal boxes of suitable size ISI marked for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS, PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable as earth wire upto common earth and connected to earth dolly including making good the diturbed surfaces compete all as specified and directed. (Note:- Three run of copper conductor of required size and one run of conduit pipe measured as one unit and also colour coding of wiring to be followed as red/yellow/blue for phase, black for neutral and green for earth)

Description all as per Serial item No 162 above but for one 5 pin 6 Amp socket outlet on independent board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 162 above but for one 5 pin 6 Amp socket outlet on same board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 162 above but for one 5 pin 15 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper cable with 2.5 sqmm single core multistraind FRLS copper cable as earthling lead complete all as specified and directed.

M&L for modular point wiring for light /fan point complete with 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor drawn through PVC conduit of suitable size as required at site, with fittings such as tee, corners, overlapping, connectors, etc fixed over walls, ceiling, floors etc including provision of 1.5 sqmm PVC insulated copper cable FRLS as earth continuty and fabricated branded modular metal flush boxes with modular white cover plate and frame concealed in walls with suitable modular fitting housing switches, socket outlet and fan regulators etc, complete all as specified and directed. (Note:- Three run of copper conductor of required size and and colour coding of wiring to be followed as red/yellow/ blue for phase, black of neutral and green for earth)

Description all as per Serial item No 166 above but for one 5 pin 6 Amp socket outlet on independent board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 166 above but for one 5 pin 6 Amp socket outlet on same board controlled by one 6 amp switch, complete all as specified and directed.

Description all as per Serial item No 166 above but for one 5 pin 15 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistraind copper cable with 2.5 sqmm single core multistraind FRLS copper cable as earthling lead complete all as specified and directed.

M&L for Switch piano, flush type single pole, one way 6 Amp, 240 volts, complete all as specified and directed.

M&L for Switch piano, flush type single pole, one way 15 Amp, 240 volts, complete all as specified and directed.

M&L for socket outlet 2 in 1, flush type single pole, one way 5 pin 5 Amp , 230 volts, complete all as specified and directed.

M&L for socket outlet 2 in 1, flush type single pole, one way 5 pin 5/15 Amp , 230 volts, complete all as specified and directed.

S&F for ceiling fan regulator elctronic, flush type, hum free suitable to control speed of fan from 0 to 100% stepped type five step 240 volts AC complete all as specified and directed.

S&F for modular switch 6 Amps, one way, one module, complete all as specified and directed.

S&F for modular switch 16 Amps, one way, one module, complete all as specified and directed.

S&F for modular socket outlet combination 2/3 pin, 6 Amp , 230 volts, 2 module complete all as specified and directed.

S&F for modular socket outlet combination 6 pin, 6/16 Amp , 230 volts, 2 module complete all as specified and directed.

S&F for modular stepped type fan regulator electronic, 120 watt, 2 module, complete all as specified and directed.

S&F for ceiling rose 3 phase/PVC/polycarbonate isolated body surface bakelite 2 to 3 terminals, complete all as specified and directed.

S&F in replacement for lamp holder insulated body PVC/ Polycarbonate type with back plate suitable for batten/angular/pendent fittings including LED lamp 9watt complete all as specified and directed.

M&L in repair for LED Tube light fitting, complete with 1x 20 watts, 220V, AC decorative box type with driver, holder in and including LED tube light connection complete prewired and connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core and connector block etc and necessary fixing arrangement at any height complete all as specified and directed.

Taking down ceiling fan of size 1200/1400 mm sweep and dismantling blades and removing fan and blades to store and refixing fans in same position including connecting to ceiling rose to fan with cable and testing complete all as specified and directed.

M&L in replacement for sheet metal enclosure MCB distribution board, double door single pole and neutral with IP-66 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. (Note:- MCBs will be measured separately.)

M&L for MCB single pole 240 volts any rating from 6 to 40 amps, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M&L for MCB single pole & neutral 240 volts any rating from 6 to 40 amps, 'C' series/curve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in repair for environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head 1x10 watt 6000 K inbuilt LED luminaire comprising of high brightness LEDs, IP54 protection including connecting electrically using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.

Supply,laying, jointng and testing, XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 16 sqmm 2 core laid in trenches, ducts, pipes, on poles and connection with necessary cables lugs, glands , complete after taking down old unserviceable cable all as specified and directed. (Note :- Excavation of earth work, removing, returning filling in, sand cushoining, concrete cable cover and protection GI pipe shall be measured and paid separetly and length of calbe shall be one length unless otherwise as directed by GE).

S&F for speading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR part-I and as directed. Note: punned thickness i.e. 18 cm shall be measured for payment purpose.

M&L in replacement for brick covering with width equal to length of brick as mechanical protection to cable using sub class ‘B’ bricks laid flat, size 230mmx115mmx75mm over the cable abutting each other, complete all as specified and as directed.

M&L in replacement for 50mm dia galvanized steel tubing (light grade) with complete all fittings such as elbow, unions, nipples, tees, bends, short pieces, connections, check-nuts, caps, plugs, diminishing pieces and flanges etc as in pole, crossing of roads, laid in trenches, fixed on walls with clampss, nuts, bots for protection of cable, complete all as specified and directed.

S&F in repair for LED building security light 35 watts, 240volts, AC, outdoor type with high pressure diecast housing with individual LEDs as light source and lence embedded PC cover having Top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 complete with connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable size 1.0 Sqmm including 40mm dia GI tubing light grade made to shape 1.20m long duly painted with aluminium paint over a coat of primer including MS clamp and back plates fabricated from steel section including nut, bolts, washers 02 set, complete all as specified and directed

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2009 including testing on completion including taking down existing unserviceable earthing complete all as specified. (Note:-Earthwork, Earth strip and protection pipe upto board is included in the rate quoted)

M/S SURINDER PAL (BID ID -3139817)

SUNIL KUMAR SANGEET KUMAR AND SONS (BID ID -3145734)

M/S Darshan Kumar (BID ID -3138278)

RAJINDER CHOUDHARY (BID ID -3138327)

Ankit Sagar (BID ID -3146279)