REPAIRS TO DIFFERENT TYPES OF FURNITURE AT VRDE AHMEDNAGAR 06

Amount

Removing unserviceable part of timber carefully from existing position and replacement of timber parts made of teak wood (Ist class HW) all as specified and shown in standrad drawing of furniture for the following items of furniture. (A) CHAIR DINING :- (Drg No F-228, FD-279) (i) Front legs as shown on drawing.

(ii) Rear legs as shown on drawing.

(iii) Front rails shown on drawing.

(iv) Rear rails shown on drawing.

(v) Side rails shown on drawing.

(vi) Bottom stiffeners as shown on drawing.

(B) CHAIR EASY :- (Drg No FD-229, FD-17, DB-3690) (i) Legs as shown on drawing.

(ii) Arms as shown on drawing.

(iii) Seat side rails as shown on drawing.

(iv) Seat front rails as shown on drawing.

(v) Seat rear rails as shown on drawing.

(vi) Back rest as shown on drawing.

(vii) Front rails as shown on drawing.

(viii) Rear rails as shown on drawing.

(c) CHAIR WRITING :- (Drg No FD-20, FD-250, FD-258 & FD-280) (i) Front legs as shown on drawing.

(ii) Rear legs as shown on drawing.

(iii) Front rails as shown on drawing.

(iv) Rear rails as shown on drawing.

(v) Side rails as shown on drawing.

(vi) Stiffeners as shown on drawing.

(vii) Arms as shown on drawing.

(viii) Back supports as shown on drawing.

(D) REPAIRS TO SOFA SET 5 SEATER :- (Drg No FD-281, FD-373, FD-258) (i) Replacing of old unserviceable cushions with removable cover

(ii) Replacing of intermediate wooden supports

(E) REPAIRS TO STOOL DRESSING LADIES :- (Drg No FD-27) (i) Replacing of old unserviceable long rails as shown on drawing.

(ii) Replacing of old unserviceable side rails as shown on drawing.

(iii) Replacing of old unserviceable legs as shown on drawing.

(F) OFFICE TABLE:- (Drg No FD-42(M), FD-231, FD-239, FD-224, FD-88) (i) Replacement of old unserviceable top with new top made out of 18mm prelaminated particle board both sides laminated with 4mm teak wood beeding at 4 sides as per drgs.

(ii) Replacement of old unserviceable legs with new legs made out of 1st class teak wood as per drgs.

(iii) Replacement of old unserviceable long rails with new long rails made out of 1st class teak wood as per drgs.

(iv) Replacement of old unserviceable short rails with new short rails made out of 1st class teak wood as per drgs.

(G) TABLE BED SIDE:- (Drg No FD-28 (M), FD-248, FD-276) (i) Top of table center 18mm thick pre laminated particle board including 4mm thick Ist class Teak Wood beeding of edge as shown in drawings

(ii) Side planks with 18mm particle board including french polish

(iii) Bottom planks with 18mm particle board including french polish

(iv) 6mm commercial plywood of size as shown drawings

(H) TABLE PEG :- (Drg No FD-236, FD-277, DB-3978) (i) Top of Peg table with 18mm thick pre laminated particle board incl 4mm thick 1st class hard wood teak wood beading of edge including french polishing.

(ii) Long rail of 1st class hard wood teak wood including french polishing.

(iii) Short rail of 1st class hard wood teak wood including french polishing

(iv) Leg of 1st class hard wood teak including french polishing

(I) TABLE DINING FOR 06 PERSONS :- ( Drg No FD-273, FD-239, DB-10081) (i) Top of dining table with 18mm pre laminated particle board including 4mm thick 1st class hard wood teak wood beading on edge including french polishing.

(ii) Leg of dining table of 1st class hard wood (teak wood) of dining table including french polishing.

(iii) Long rail of 1st class hard wood teak wood including french ploishing all as shown on drawing.

(iv) Short rail of 1st class hard wood teak wood including french polishing all as shown on drawing.

(v) Stiffener of 1st class hard wood teak wood including french polishing all as shown on drawing.

(vi) Provn of new brackets 08 Nos. for each table of 1st class hard wood including french polishing all as shown on drawing.

(J) TABLE WRITING :- (Drg No FD-33, FD-249, FD-275 DB-3975) (i) Replacement of old unserviceable top with new top made out of both side prelaminated particle board one side teak face and other side white face 18 mm thick with 4 mm teak wood beeding all as per drgs.

(ii) Replacement of old unserviceable legs with new legs made out of 1st class teak wood as per drgs.

(iii) Replacement of old unserviceable long rails with new long rails made out of 1st class teak wood as per drgs.

(iv) Replacement of old unserviceable short rails with new short rails made out of 1st class teak wood as per drgs.

(v) Replacement of old unserviceable drawers with new drawers as per drgs.

(vi) Replacement of old shutters of cupboards with new shutters as per drgs.

(vii) Replacement of old side portion of cupboards with new side portions as per drgs.

(viii) Replacement of old back portion of cupboards with new back portions as per drgs.

(ix) Replacement of old long stiffner with new long stiffner as per drgs.

(x) Replacement of old short stiffner with new short stiffner as per drgs.

(K) REPAIRS TO BED HARD PLY TOP : (Drg No FD-246, FD-21) (i) Removing of old unserviceable head board and S&F new head board and duly french polished complete all as shown in drawing and as directed by Engineer-in-Charge.

(ii) All as per item No.11 (i) above but for foot board

(iii) Removing old unserviceable long rail and S&F new Long rail all as shown on drawing

(iv) Removing old unserviceable short rail and S&F new Short rail all as shown on drawing

(v) Removing old unserviceable 12mm ply wood and S&F new 20mm thick commercial ply wood of superior quality including beading fixed with favicoll all round as approved by Engineer-in-Charge and specified on drawing.

(vi) Removing old unserviceable intermediaries and S&F new Intermediaries stiffners duly french polished complete all as shown on drawing and as directed by Engineer-in-Charge.

(vii) Providing new bracket for each leg.

Removing old cane and recanning any type of chairs (seat or back) except chair varandah stool dressing CB Binsoiled linen etc as specified and shown on drg and as directed by Engr-in-Charge. (Drg No FD-16(M), FD-228, FD-279,FD-20, FD-250, FD-258, FD-280, FD-229, FD-17 & DB- 3690)

Cleaning and polishing of wooden and wooden based furniture any description of any grith and applying french polish to glossy finish to articles as shown on drg and to entire satisfaction of Engr-in-Charge for the following furniture article. (i) Bed Hard / Bed Newar (Drg No FD-246, FD-21, FD-245)

(ii) Bin soiled linen (Drg No FD-244)

(iii) Book case (Drg No FD-237)

(iv) Chair eazy (Drg No FD-229, FD-17)

(v) Chair Dinning (Drg No FD-228, FD-279)

(vi) Chair writing (Drg No FD-20, FD-250, FD-258, FD-280)

(vii) Chair CB office (Drg No. DB-4124, DB-4170)

(viii) Chair with desk (Drg No FD-80)

(ix) Desk and seat combination (Drg No F/IAT/14/65/S-16))

(x) Desk student (Drg No GF-41)

(xi) Desk with bench type 'A' (Drg No F-20)

(xii) Foam with out back (Drg No F-7, FD-77(M))

(xiii) Hat stand (Drg No FD-223)

(xiv) Locker bed side (Drg No DB-4047, FD-54(M))

(xv) Rack side 3/4 space (Drg No DB-4123, FD-97)

(xvi) Locker bed side (Drg No DB-4047, FD-54 (M) )

(xvii) Side board (Drg No FD-241 & GF-29)

(xviii) Sofa set 5 seater (Drg No FD-281, FD-373, FD- 40)

(xix) Board Notice (Drg No DB-10182))

(xx) Base cabinet type 'B'

(xxi) Base cabinet type'D'

(xxii) Base cabinet type'E'

(xxiii) Base cabinet type'F'

(L)Repairs to Almirah large/Medium steel (i) Removing the existing underviceable old locks from Almirah Steel supply and fix new lock made out of steel body grade I type of 75mm size with six brass levers (Make: Aligarh) and with duplicate keys all and fixed to the steel Almirah with four screws or as required and directed by Engineer-in-Charge.

(ii) Removing existing unserviceable handle from steel Almirah, supply & fix new steel chromium plated handle of 150mm size all as per Godrej pattern and fixed to steel Almirah with hexogonal nut & steel pin of appropriate size complete all as specified and directed by Engineer-in-charge.

(iii) Taking down existing shelves of any size carrying out all minor repairs to the shelves, refixing the same to the steel Almirah with providing four Nos of new cleats with nuts & bolts all as specified and directed by Engineer -in-Charge.

(v) S&F new locking device complete vertical pair of mild steel rods 10mm dia made to shape 3mm thick MS plate steel body lock 75mm size, six brass levers with duplicate keys and of Godrej lock 1mm thick MS sheet cover complete all as shown on drawings, specified and directed by Engineer-in-Charge. (i) For Almirah large steel

(ii) For Almirah med steel

(vi) Removing the dents, bends of steel Almirah welding to broken portion, rectifying all minor defects and repairs. M&L for preparation of steel surface of almirah (inside and outside) including doors shelves and legs. Providing high class glossy finish with synthetic enamel paint over a coat of red oxide primer where ever required. Complete all as specified and directed. (i) For Almirah large steel

(ii) For Almirah med steel

(M) Revolving chair (i) Replacing old damaged base platform with new base platform made of hard PVC with castor nylon wheels of good quality to suit the existing size and design of chair revolving low high and medium backs(trade pattern) complete all as specified and directed by Engr In Charge

(ii) Replacing and damaged hand rest of chair revolving High back(Trade pattern) with new hand rest made of polyurethane material to suit the existing size and design complete all as specified and directed

(iii)Replacing old damaged and unserviceable assembly bolt with new hydrolic stem assembly approved quality to suit the existing size and design of chair revolving low,high and medium backs(Trade Pattern) complete all as specified and directed.

(iv)Replacing old damaged and unserviceable assembly tiling bolt with new tiling service assembly approved quality to suit the existing size and design of chair revolving low,high and medium backs(Trade Pattern) complete all as specified and directed.

(v)Removal of old and unserviceable fabric/rexene and foam from the seat and back of chair and replacing with new approved quality fabric/rexene (cost not less than Rs 250/metre) and foam as per existing size quality) and design for chair revolving high back(trade Pattern) complete all as specified and directed

(vi)Removal of old and unserviceable fabric/rexene and foam from the seat and back of chair and replacing with new approved quality fabric/rexene (cost not less than Rs 250/metre) and foam as per existing size quality) and design for chair revolving Medium back(trade Pattern) complete all as specified and directed

(vii)Removal of old and unserviceable fabric/rexene and foam from the seat and back of chair and replacing with new approved quality fabric/rexene (cost not less than Rs 250/metre) and foam as per existing size quality) and design for chair revolving Low back(trade Pattern) complete all as specified and directed

(N) Office steel chair (Drg No FD-75) (i) Removing the existing broken/damaged wooden seat frame of chair steel tubular with arms and providing with new hardwood frame duly canned and painted with two coats of black synthetic enamel paint all as specified and directed by Engineer in Chrage

ii) Removing the existing broken/damaged wooden seat frame of chair steel tubular without arms and providing with new hardwood frame duly canned and painted with two coats of black synthetic enamel paint all as specified and directed by Engineer in Chrage

(O) PRELAMINATED PARTICLE BOARDS :- M&L for prelaminated particle board, 18/19 mm thickness,interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber work including removal of old u/s partical board of any description complete all as specified and directed.

M&L for external teak wood lipping, 6mm thick fixed with nails to prelaminated particle board 18/19 mm thickness including removing of old lipping complete all as specified and directed.

KAMINS CARE

Mahesh Traders