GE/863/EWS-T-49 OF 2021-22

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness inclduding cover fillets complete all as specified and directed.

Dismantling boarding, any description fixed in any position with nails complete all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, in any positions as in framed work complete all as specified and directed.

-Ditto- all as per item above but in fillets, rails, posts, rafters, purlins, etc under 40 sq.cm in section.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of PCC block masonary, ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Taking down chowkhats or frames not exc 1.5 sq.m each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames) complete all as specified and directed.

M & L for second class hardwood, clean sawn, scantlings as in timber framed work complete all as specified and directed.

-Ditto- all as above but except timber.

M & L for 6mm thick (No of ply 5) plywood, grade BWR, type BB, fixed with nails to timber frame work as in ceiling complete all as specified and directed.

M&L for 9mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one side face, fixed with screw for timber framed work complete all as specified and as directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 3 & n.exc 6 sq.cm complete all as specified and directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc 13 & n.exc 25 sq.cm complete all as specified and directed.

M & L for pre-cast cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in block masonry with solid blocks, exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 but EXCEPT STONE complete all as specified and directed.

M & L for providing precast cement concrete Type C1 1:3:6 using 20mm graded stone aggregate and set in cement mortar 1:6 as in bond stone complete all as specified and directed.

M & L for providing cement concrete Type C1 1:3:6 using 20mm graded stone aggregate as in coping complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.50mm graded stone aggregate as in floor, including rough finished without using extra cement complete all as specified and directed.

M & L for non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M & L for glazed ceramic coloured tiles in vertical surface 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including screed bed of 20mm thick in CM 1:4 including rubbing and polishing complete all as specified and directed.

M & L for chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed in cement mortar 1:4 as in floors with grey cement and pigment complete all as specified and directed.

M & L for cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in roof kerb or mud stops, round on edges complete all as specified and directed.

M &L for 75 mm thick cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate, finishing surface even and smooth without using extra cement as in plinth protection complete all as specified and directed.

M & L for RCC 1:2:4 type B-1 ( using 20 mm graded stone agg ) as in chajjas complete all as specified and directed

M & L for RCC 1:2:4 type B-1 ( using 20 mm graded stone agg ) as in Beams , cantilevers, bressummers, lintels etc complete all as specified and directed

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S & F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 6 to 8mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F 0.63 mm thick galvanized, corrugated mild steel sheeting with two corrugation side lap, using grade of zinc coating -275 inclusive of both sides, fixed with ‘L’ or ‘J’ type hooks or cranked hook / bolts and washers as in roof covering etc. complete all as specified and directed.

S & F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Plain Galvanised, mild steel sheeting 1.00 mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and directed.

S & F of 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement plaster 1:4 using WPC 3% by weight of cement and finished even and smooth (without using extra cement) complete all as specified and directed. NOTE: WPC to be measured and paid separately in respective item as 'Supply Only'.

M & L for rendering 15mm thick on stone walling in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in cement mortar 1:3 complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

M & L for rendering 10mm thick on fair faces of brick or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement) complete all as specified and directed.

S & F second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F second class hardwood 35 mm thick plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers and fitted to chowkhats complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S & F of 30 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule part – I (Specifications - 2009) complete all as specified and directed.

S & F MS clamps, hold fast,hook washer & similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M & L for providing plain cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in hold fast blocks complete all as specified and directed.

S & F 125mm butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed.

-Ditto- all as per item above but 75mm long.

S & F 300mm length aluminium alloy, anodised, sliding door bolt hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F 150mm Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 125mm Aluminium handles, cast type, anodised complete all as specified and directed.

S & F 150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F 125mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F mild steel 300mm ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

M & L sheet glass, 4mm thick ordinary quality and glazing with oil putty or beadings in square not exc 0.5 sqm in each pane complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of chalk whitning as a preparatory to distempering complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of wood and wood based materials, new or old surface of any description and girth not otherwise described and treated with two coats of creosote oil complete all as specified and directed.

M & L for preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of old wooden surface of any description not otherwise described and exc 10cm width or girth applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of old surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

S & F in repairs Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.complete all as specified and directed.

Taking down carefully copper/aluminium point wiring from existing points (light, fan, socket or power) alongwith compete fittings such as switches ,ceiling rose, pendent holder, sketcth fitting & regulator etc including making good to the distrurbed surfaces of wall, roof and floor etc to match with the existing surfaces complete all as specified and directed .

Taking down unserviceable service cable alongwith batten /PVC conduits etc. and making good disturbed surfaces of walls/floors and match the existing surface all as directed at site.

Taking down unserviceable main switches, DBs with MCB SP/Isolators by unscrewing form board complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS by using FRLS PVC insulated 1.5 Sqmm multi stranded ,1100 volts grade, copper conductor cable, unsheathed type, alongwith 1.5 Sqmm FRLS PVC insulated stranded copper conductor cable for continous earthing in & incl PVC casing & caping with accessories fixed on wall surfaces / ceiling including provision of 2 mm thick sheet metal terminal box with 3 mm thick hylam laminated sheet on top for fixing switches sockets etc, for one light point / fan / Bell point controlled by one switch complete all as specified and directed .

All as per Srl item No 75 here-in-before but controlled with one 3 pin socket outlet 5 Amp on independent board with other switches with cable 1.5 Sqmm .

All as per Srl item No 75 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the same board with other switches with cables 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge.

All as per Srl item No 75 here-in-before but controlled with one 3 pin socket outlet 15 Amp, independent board with other switches with cables 2.5 Sqmm.

Supply and fixing switch piano type 5 Amp, 230 Volt, flush button, single pole one way complete all as specified and directed .

Supply and fixing socket outlet 3 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed.

Supply and fixing switch piano type 15 Amp, 230 Volt, flush type, single pole, one way complete all as specified and directed.

Supply and fixing socket outlet 3 pin 15 Amp 2-in-one 230 Volt flush type complete all as specified and directed.

S&F Bell push flush type 5/6 Amps complete all as specified and directed.

S&F Bell AC 230 volt multi music type single pole complete all as specified and directed.

S &F Ceiling rose, 3 terminal complete all as specified and directed.

S & F lamp holder, PVC/ Polycarbonte type with back plate suitable for batten/pendant fittings complete all as specified and directed.

Supply and fixing LED Lamp 23 watt , Make Crompton Base B22 complete all as specified or equavalent Make- Philips/Havells/Bajaj).

S&F in replacement of LED integrated batten tube light fittings 20W, 4 Feet long, complete with twin core twisted flexible copper conductor cable complete all as specfied and directed. Make: Crompton Model -Trimline LDL-20CDL or equivalent make as per Appx 'B' as approved.

Supply and fixing in replacement LED light fitting mirror type, 2ft of 10W, 6500 K , with high grade diffuser for better optical control, complete all as specified and directed. Make : Crompton , Model : Light Linea or equivalent make as per Appx 'B' as approved.

Supply and fixing in replacement of Bajaj LED 10 watt Bulk head light fittings, cool white, color temperature 3500-4100K wall mounting type equavalent make : CG/Philips/wipro etc complete all as specifed and directed.

Supply and fixing in replacement slim LED Panel light of capacity 18W of size 225 x 225 mm, square type complete all as specifed and directed.

Supply and fixing sheet metal enclosure for DBs, single pole and neutral , 8 way, 240 volt, Double Door with 200 amp rated bus bar complete all as specified and directed .

All as per item No. 93 here-in-before but for 4 way.

S&F MCB SPN 40 Amp, complete all as specified and directed .

S&F MCB SP, 6 Amp to 32 Amp, 240 Volts , 10 KA complete all as specified and directed .

S&F exhaust fan , steel body, heavy duty, AC, Single Phase, 300mm sweep, with blades, frame & louvres complete all as per specified and directed.

Supply,fixing, Testing & commissioning electric water heater,storage type, rust proof ,powder coated, steel body ,with copper inner tank and heating element upto 2 KW ,capacity 25 litre, BEE 5 Star rated, electric operated 230 V, Single Phase complete with all accessories such as safety valve, thermostate, NRV, connection piece, multifunctional safety valve, automatic thermal cut out, fusible plug, anti vacum sys, built in presser release valve,thermostat, indicator lamps and all safety devices including provn of grouting bolts in walls including CP brass fancy type pillar cock 15 mm , PVC connection PTMT, 450 mm long etc and making good to disturbed surfaces complete all as specified and directed .

S & F submain wiring with FRLS PVC insulated single core multistranded copper conductor cable 1100 Volts grade, 2 runs of 6 Sqmm and one run of 4 sqmm as earth wire all drawn through in & incl in PVC casing caping of suitable size medium grade complete all as specified and directed .

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead GI strip 25x4 mm earth continuity conductor by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I,connected to earthing test point all as specified or indicated including testing on completion ,necessary excavation, earthwork, PCC works in 1:2:4 type B-1, form work and CI earth pit cover with watering pipe 20 mm dia GI Pipe medium grade, funnel with wire mesh and lugs, GI Pipe of 15 mm dia of light grade for protection of earth strip including taking out old earthing complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I,connected to earthing test point all as specified or indicated including testing on completion ,necessary excavation, earthwork, PCC works in 1:2:4 type B-1, form work and CI earth pit cover with watering pipe 20 mm dia GI Pipe medium grade, funnel with wire mesh and lugs, GI Pipe of 15 mm dia of light grade for protection of earth wire including taking out old earthing complete all as specified and directed.

M & L in replacement of Earth continuity conductor of Aluminium strip of size 25 x 4mm or main earthing lead fixed to wall with insulators or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc complete all as specified and directed.

M & L in replacement of Air termination, single pointed aluminium rod, 12mm dia and 300mm long complete as specified and directed.

M & L in replacement of Test point terminal block made out of of gun metal or hosphorus bronze of size 75x75x25 mm drilled and screwed including 3 nos.. 8mm dia, 25mm long hex. head screw complete all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular of size 16 Sqmm complete all as specified and directed.

Supplying, laying, jointing & testing in replacement of cable XLPE insulated as per IS 7098 (Part-I)-1988, marked, screened, PVC sheathed, armoured ,electric power cable ( heavy duty) with aluminium conductor for working voltage upto and including 1100 Volts, croos sectional area 16 Sqmm, 4 core with aluminium stranded conductor, laid in trenches / fixed on pole / wall / passed through pipe complete all as specified and directed . Note :- Road cutting and making good with PCC 1:2:4 (using 20 mm graded stone aggregate) shall deemed to be included in quoted rate.

Excavation in trenches not exc 1.5 Mtr wide and not exc 1.5 Mtr in depth in hard/dense soil for laying under ground cables / erection of steel tubular poles / stay pit etc complete all as specified and directed .

Returning, filling in, incl spreading ,levelling ,watering and well ramming in layer n exc 25cm in soil each layer complete all as specified and directed.

Removing excavated surplus material to a distance n exc 50m and depositing where directed at level n. exc 1.5m above the starting point in any type of soil complete all as specified and directed .

M & L for sand cushioning the UG cable, screened, unwashed, river sand and punning for cushioning to cable complete all as specified and directed .

M & L for laying dry bricks old size with sub class 'B' made of burnt clay, best quality ,locally available with permissible tolerance , laid straight in trench for protection of cable complete all as specified and directed .

S & F in replacement of GI tubing 40mm (Light grade) laid in trenches under road or fixed to wall as mechnical protection of UG cable complete all as specified and directed.

Net Contract Sum will be after deducting Sch Of Credit of Rs. 55284.00

M/S PYARE LAL

M/S Shamsher Negi Dewa