SPL REPAIR AND UPGRADATION OF BLDG NO P-17 (04 DUS) AND CERTAIN MINOR WORKS AT SHANKAR VIHAR UNDER AGE B/R-II OF GE (SOUTH) DELHI CANTT-10

Amount

M & L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M & L for Anti termite Treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

M & L for Dismantling of brick tiles (laid flat or on edge) on roof surface.laid bedded and pointed in any mortar.

M & L for Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area or as directed by Engr in charge.

M&L Cutting out craks to V-section in existing roof or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 , complete all as specified and as directed

Preparation of concrete surfaces by wire brush and cleaned top surfaces of cement concrete complete all as specified and as directed.

M&L for Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) avg 40mm thick as in roof pedding , finished even and smooth without using extra cement ,including cleaning the concrete surface by steel wire brushes, up to three stories bldgs, complete all as specified and as directed.

M&L for Priming roof surfaces and applying water proofing treatment over roofs comprising of the following complete all as specified and as directed.

(a) Applying oil bound bituminous primer at the rate of 0.30 Ltrs/Sqm as per IS 3384-1986 on prepared surfaces. Surface shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated.

(b) Applying one coat of hot straight run bitumen @ 1.20 Kg/Sqm of grade 30/40 confirming to IS-73 (Grade S-35).

(c) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 kg/sqm, black finish reinforced with non woven polyster matt, (weight not less than 160 gm/Sqm) with a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer's instruction including preparation of surface.

(d) The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators. The contractor shall give 10 years guarantee for effectiveness of water proofing treatment, 2.5% of work done amount of this item shall be retained from contractors payment for a period of 10 years reckoned from date of physical completion of this work, or in lieu contractor may deposit bank FDR for the said amount for 10 years which shall be released by GE on expiry of satisfactory completion of 10 years period.

M&L for plain cement concrete tiles with grey cement and no pigment as in roof tiles of size 250 mm x250mm x 20 to22 mm thick laid over and including 20 mm thick bedding in cement mortar (1:6) and gap between tiles not exceeding 8 mm , grouted up to full thickness of tile with cement mortar (1:3) Mixed with water proofing compound Complete.

Demolition of stone slab and tiles of any description or thickness on cooking platform, floors, aprons etc laid bedded and pointed in any morter complete all as specified and as directed

M & L for Granite (of any type) work, 18-20 mm thk (table rubbed and polished) in steps,jambs,pillars, window-cills, cooking platforms with necessary hole for gas pipe where ever required and likes over and including cement mortar bedding of 15mm thick in CM 1:6 including pointing in white cement using marble dust with admixture of pigment to match including rounded edges with shade of granite complete all as specified and as directed.

M&L for Udaipur green marble work 18 to 20mm thick (table rubbed and polished) in steps, riser/skirting, jambs, pillars, window cills, and like including 20mm thick screed bed in CM 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M & L for Glazed Ceramic coloured tiles in vertical surface 450X350X7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat of cement mortar (1:4), complete all as specified and as directed.

M&L Non Skid ceramic tiles 8 to 10 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and as directed.

M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm of size (600mm X 1200mm), in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and including 10mm thick rendering in cement mortar (1:6) complete all as specified and as directed.

M&L for vitrified ceramic tiles double charged (light shade) 10 mm thick (Square/ rectangular) area of each tile not exceeding 0.36 sqm as in skirting laid on 10mm thick cement plaster in CM (1:4) , set and jointed in neat cement slurry at the rate of 3 kg per sqm and pointed in white/coloured cement to match the shade of tiles.

M&L Non Skid ceramic tiles 8 to 10mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including screed bed or bedding layer of mortar 15mm thick in CM 1:6 complete all as specified and as directed.

S&F in repairs Vitreous china wash down water closet pan sinlge piece syphonic action, white including cistern of 10 litre capacity & soft close sheet cover of closed pattern with flat bottom complete.

S&F in repair CP brass health faucet with hand shower and 1.5 mtr flexible stainless steel pipe suitable for fixing to 15 mm dia pipe complete.

S & F in repair toilet paper holder of mild steel Chromium plated ‘D’ type, fixed in repairs to walls with chromium plated brass screws complete.

S & F in repair Vitreous china wash basin with pedestal white, flat back, size 550 x 400mm, including necessary waste pipe and coupling, brackets and cutting for and pinning in ends of brackets, complete.

S&F in repairs elegent mirror PVC cabinet without towel rail of size 422 x 622 mm all as specified.

S&F in repairs bib tap, brass chromium plated fancy type, quarter turn long body screwed down, screwed for iron pipe 15 mm bore complete.

S&F in repairs PVC connection 15 mm size with brass nut of length 450 mm.

S&F in repairs stainless steel foldable towel rack 60 cm long and 24 cm deep with towel rail and hangers at bottom fixed to walls complete all as specified and as directed.

S&F in repairs brass chromium plated shower rose of size 125 mm with arms including fixing to steel pipe.

S&F in repairs 6 mm thk glass corner shelf fancy type with railing and fitting complete of size 25cm x 25 cm of best quality (as per sample approved by Engr -in-charge)

S&F in repairs wash hand basin mixing valve 15mm dia CP brass fancy type including joints to steel pipe or unions all as specified.

S & F in repairs Brass CP Wall mixer (Non Telephonic Type) with L bend 3-in-1 for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified.

S&F in repairs kitchen sink mixer 15mm dia CP brass fancy type including joints to steel pipe or unions complete all as specified and as directed.

S&F in repair Conceeled stop cock,15 mm bore, chromium plated ,with long shank and cup, fancy type, complete all as specified and as directed .

S&F in repair 15 mm dia brass chromium plated angle valve screwed at ends including necessary extention piece and fixed complete.

S&F in repairs Cast iron floor/Nahani trap with grating including jointing to waste pipe in run lead, dia of outlet 100mm in cement concrete type B1 (1:2:4) complete all as specified.

Demolition of lime concrete of any description and in any position complete all as specified.

M & L 25 mm thick PCC 1:2:4 B1 using 20 mm graded stone aggregate over 250 thick cement concrete type E2 ( 1:3 ) with 40mm brick bats as in filling of sunken floors over a layer of polyethylene film black 50 micron over a layer of bitumen blown any grade applied hot (1.5 Kg/sqm) over 10mm thick plaster in cm 1:3 with WPC @2% by wt. of cement including treatment to side wall of sunken complete all as specified & as directed Note Over all floor area only shall measured for payment and the rate quoted by the tenderer are deemed to be included for treatment of side wall also.

Taking down (Door) chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) and removing to store complete.

Taking down (Door) chowkats or frames with shutters (without taking of shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each and removing to store complete.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 65x 125 mm comprising of virgin PVC polymer of K value 50-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and non toxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge.Note: For WPC solid door/windows frames,minus 5mm tolerance in dimension i.e depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory Made single extruded WPC (Wood Polymer Composite) Solid door/window/Ceosetory windows & other frames/ chowkat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers( wood powder/ rice husk/ wheat husk) and nontoxic additives ( max toxicityindex of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face & 1100 N Edge), min compressive strength of 58N/sqmm and resistance to flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed with MS Holdfast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engr in charge. Note: -For WPC solid door/windows frames, minus 5mm tolerance in dimension i.e., depth and width of profile dimension on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item).

Providing 30mm thick FACTORY-MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (Confirming as per IS:4020). The door should be water proof, termite proof,fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. SS butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through Other hardwares shouldbe fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings.” Note: Fixture/fittings shall be measured & paid under relevant item

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer -In- Charge. (Note: stainless steel butt hinges shall be paid separately under relevant item).

M & L for Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in back filling, holdfasts etc, complete all as specified and as directed.

Taking down (steel Window) chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete.

Taking down (Steel Window) chowkats or frames with shutters (without taking of shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete.

S&F fabricated aluminum window with powder coated anodized aluminum frame of section 63.5mm x 38.10mm x1.5mm thick, shutter with section 47.62mmx44.45mmx1.5mm thick including aluminum anodized “D “ handle, hinges, peg stays, tower bolts, etc including jointing cleats for fixing builder's hardware fittings & stainless steel wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples including necessary fittings/fixture /aluminum snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

M&L poweder coated aluminium anodised three way track sliding windows of frame size 92 mm x 31.75 mm x 1.5mm thickness (section no. 20831 of JINDAL) and of shutter size 40 mm x 18 (with 9.00 mm interlocking legs) x 1.45 mm thick (section no. 20737 of JINDAL) section(two shutter glazed, covering half of span of opening each & one shutter sketlon covering half of span of opening ) incl provn for making windows air tight, including 95mm aluminium handle with spring lock , stainless steel wire cloth, 0.45 mm nominal dia of wire and average width of aperature 1.4mm and fixed with steel wire stapples and 5mm thick plain glass including necessary fitting/ fixture/ aluminium snap beads complete all as specified. Note: Measurement shall be taken for clear opening i.e. out to out of window frame as a whole including all fittings and fixtures and no extra shall be paid separately.

Dismantling wrought iron or mild steel/cast iron work of any description (steel window & Grill) complete all as specified and directed.

M & L for Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, welded or forged into spikes, framed guard bars, window frames, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work fixed in position including holdfasts or screws confirming to Fe.290.Gde-E-165 complete all as specified.

S & F for mild steel, 150 to 200 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

M & L for preparation of new Steel surfaces of any description not otherwise described over 10 cms width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer all as specified.

S&F stainless steel butt hinges,size 100 mm of Gde-304 complete.

S&F stainless steel Gde-304 barrel tower bolts of extruded section 200 mm long.

S&F 150 mm stainless steel handles Gde-304 all as specified.

S & F stainless steel sliding door bolt 300 mm long of Gde-304, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts complete.

S&F Magic eye and fixed to doors all as specified and directed complete.

S & F Hasp and staple -100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete.

S & F Floor door stopper (double leg) of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 60mm complete.

S&F 25 mm stainless steel curtain rod with fixing brackets, side knobs complete all as directed. (MAKE : AS APPROVED BY GE)

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete.

M & L for Cement concrete 1:3:6 type C2 using 20mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement, complete.

Cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth.

Taking up or down steel tubing and connections, including cleaning for re-fixing all as specified.

a) 15 mm bore

b) 20 mm bore

c) 25 mm bore

S&F GI tubing medium grade galvanised with all fittings, laid in walls, ceiling, floors, etc all as specified.

a) 15 mm bore

b) 20 mm bore

c) 25 mm bore

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres complete.

S&F 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part II.

S & F in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore complete.

S & F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes Pipe ; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete.

Supply and fix in repairs PVC waste pipe 32 mm bore, 65 cm long complete.

Dismantling of cast iron or reinforced concrete drains pipes fixed to walls, jointed in cement morter and taking out of trenches if required up to 100 mm internal dia of drains, complete all as specified and directed.

S & F in uPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in floors, of 110 mm dia complete all as specified and directed.

S & F uPVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in floors, of 75 mm dia complete all as specified and directed.

S & F 100 mm uPVC bends/Tees/branches/ Socket/ reducer socket (any radius), disminishing pieces or tapers fitted with or without oval access door complete all as specified and directed.

S & F 75 mm PVC bends/Tees/branches/Socket/ reducer socket (any radius), disminishing pieces or tapers fitted with or without oval access door complete all as specified and directed.

S & F in repairs Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for 100 mm bore pipes complete.

S & F in repairs Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, for 75 mm bore pipes complete.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand brushing scrubing down concrete surfaces with wire brushes cleaning with water allowed to dry applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of a layer of epoxy adehessive on complete exposed surfaces of concrete and provide guniting in two layers over steel welded mesh 2 mm dia of wire and total aperture 75 mm, thickness of gunite n.exc 25 mm thick (average thickness) using cement mortar 1 :3 with OPC 43 grade cement mixed with polycrete admixture @ 2 % by wight of cement or as per manufactures instructions and finally applying cement plaster over gunite surfaces 10 mm thick to give an even, uniform and smooth finish conforming to proper Geometrics in cement mortar 1:4 without using extra cement to match with the existing surface as in side and soffits of slabs,chajjas,fins,facias,parapets,columns and beams etc complete including necessary scaffolding ,shuttering necessary chased to brick work or RCC members at any height upto two storey buildings incl removing of small trees shrubs etc all as specified (Note : The cost of welded mesh is deemed to be included in the unit rate quoted.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete.

M/L cement plaster 15mm thick in CM 1:6 on brick or conc surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer @ 250gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete. NOTE : Rates for water proofing compound/ polymer deemed to be included in the above rates.

M &L for providing and applying a bond coat of Latex:Water:cement - 1:4:6 consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing complete.

Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes : Drilling holes 10mm diameter in masonary structure along the side of the joint as per manufacturer's instructions so as to cross the brick/ block at the intervals spacing of 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes : Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using sealent. Cutting of Packers : Cut the packers after completion of grouting without damaging structural elements.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperatrure and execution requirement between 8-50 mins, pH – 9-10, tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectible hose system. The holes should be drilled until a depth of approx 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump injcection of polymer resin compound at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line

M&L for 15mm thick rendering with ready mix plaster on faces of brick or concrete wall surface, finished even and smooth complete all as specified and directed.

M&L for 10 mm thick average rendering with ready mix plaster on ceiling of concrete surface finished even & smooth complete all as specified.

M & L for Preparing new plastered or unplastered surfaces of wall/ ceiling and applying two coats of exterior emulsion paint over & including a coat of wall care Putty specified for external surface as per manufacturer instruction complete. Note : Shade of paint as approved by GE/ User.

M & L for Preparing new plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion, white or tinted over & including 1 mm thick wall care Putty of desired thickness complete.

M & L preparing new plastered surface of ceiling and applying two coats of distemper oil emulsion over & including a coat of 1mm thick wall care putty of desired thickness complete.

Demolition of brick work built in cement or cement lime mortar complete.

Brick work with sub-class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete

Dismantling boarding, any description, fixed in any position with nails.

M&L for 18 mm thick wood plastic composites (WPC) board, fixed with screws fitted under or above the kitchen cooking platform and/or other platform including all necessary fittings and fixtures like nickle plated clip hinges, knobs, channels etc complete all as specified and directed. Note : (a) Pattern & design of WPC board to be decided by GE. (b) Items like cupboard knobs, stainless steel channel, CP plate clip hinges to be measured and paid in extra.

S & F CP clip on hinges (Inset) complete all as specified and directed .

S & F 40/50mm dia, cup board knobs fixed with nut, screws and washers of aluminium, anodised complete.

S&F Channel for drawer of suitable length in kitchen cabinates etc complete all as specified and directed .

S&F in repair 15mm mild steel, chromium plated rod with fixing brackets, fixed in cupboards for hanging cloth of adequate strength all as specified and directed.

S& F staianless plate rack made of 0.8 mm thick stainless steel sheet of size 750 mm x 900 mm x 210mm consisting of 3 shelf for bowls and one shelf for keeping six nos of big utensil and seven nos of small utensils divided by 10 mm dia stainless steel hollow pipe @ 60 mm centre to centre or as per drg and sample kept in GE"s office all as specified and directed by engr-in-charge complete. (Make JAYANA CAT NO SBS/09A (GLOSSY) OR EQUVILANT NIRALI/NEELKANTH)

M & L 100mm thick Cement concrete type D-2 1:4:8 (40mm graded aggregate) as in sub base.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over 50mm sand cushion complete all as specified & directed.

M&L for cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate as in coping including weathering slightly rounded or chamfered angles and throating as directed including necessary formwork complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for RCC parapet wall,fins fascia etc upto 2 storey building.

Cutting holes in brick walls in built in cement mortar or cement lime mortar exc half brick but not exc one brick complete alll as specified and directed.

Excavation in post holes in hard / dense soils , each not exc. 0.50 Cum, getting out, returning filling in and ramming earth in layers not exc. 25cm including watering & removing surplus soil to a distance not exc. 50m & making good surface complete all as specified and directed

M&L Cement concrete (1:4:8) Type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L steel work in tubuler trusses including special shaped washer, cleats etc complete using ERW or induction butt welded tubes confirming to IS: 1161-1979 grade st - 240 complete all as specified and directed.

Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified .

Surface excavation dressing n exc 30 CM deep and averaging 15 cm and getting out in soft/loose soil complete all as specified and as directed.

Taking down carefully aluminium point wiring (light/fan/bell/socket /power) with complete fittings such as steel terminal boxes, switches, ceiling roses, pendents, regulators, sockets etc and removing the material including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface all as specified and as directed.

M&L for concealed point wiring complete with stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable drawn through concealed PVC conduit and including replacement of unserviceable pressed steel terminal boxes with Modular steel terminal boxes factory made including white cover modular plate with frame suitable for modular switches, modular sockets, modular fan regulators etc of required size complete including 1.5 sqmm copper cable earth continuity wire to common earth and connected to earth dolly complete all as specified for One light/Fan/Bell point controlled by one 5 Amp switch one way using cable (1.5 Sq mm for phase and neutral and 1.5 sqmm for earthing) . Note :- The rate is inclusive cutting/chasing and making good disturbed surface with CM 1:3 and same surface finishs with the adjoining surface of disturbed area with OBD/Colour wash/white wash complete.

All as per item No 119 above but 5 Amp socket outlet on same board.

All as per item No 119 above but 3 Pin Socket outlet 5 Amps on independent board with cables 1.5 Sqmm size for phase and neutral and 1.5 sqmm for earthing complete.

All as Item No 119 above but for one socket outlet 5/15 Amps on Independent board with cables 2.5 sqmm size for phase and neutral and 2.5 Sqmm for earthing complete.

All as Item No. 119 above but for one light point controlled by two 2-way switches with cable 1.5 Sqmm size.

All as per item No 119 but for One 3/6 Pin socket outlet 20 Amp on independent board with cable 4 Sqmm for main current and neutral and 4 Sqmm as earth wire as AC point cable 4 Sqmm for main current and 4 sqmm as earth wire as power point.

S&F switch modular type, 1 way 6A, 1 module complete all as specified and as directed.

S&F switch , Modular switch 2 way 6A, 1 module complete all as specified and as directed.

S&F Modular Socket, 6A - 2/3 pin 2 module complete all as specified and as directed.

S&F of Switch modular type 1M, 16 Amp with red indication light complete all as specified complete all as specified and directed . Notes :- (i) Electric switch for geyser of 16 Amps shall be provided on main switch board of the bathroom and socket outlet shall be provided near the geyser and will be measured as 16 Amps power point wiring against item No 5.00 here-in-before.

S&F Socket 6A/16A - 2/3 pin combined 2 module .

S&F Modular Bell push 6A 1 module

S&F Decorative wall light mounting suitable for LED Lamp upto 15 Watt complete with all connections all as specified and directed. Make : HavellsCat Part No LHF0ECE1TZ10014/ HalonixCat Part HLWB-01-B22/ Philips model - Comet .

S&F in repairs surface mounted round shaped LED downlight with durable housing with Al heat shrink with diffuser to give glare free light 12 watt LED 6000K/6500K lamp type from ceiling of stairs/common areas, complete all as directed. Make : Bajaj Cat Part No-BGSLO12W6000K / Wipro Cat Part No-WP1076 / Crompton Cat Part No – LCDSPLN-R-12-CDL

S&F in repairs surface mounting LED Integrated Batten luminarie Polycarbonate 20W LED light housing. Fixture should have minimum system lumen of 2000lm & minimum efficacy at system level >=95lumens/Watt, life of fixture 25K Hrs, CCT 4000-6500K with same lumens/w CRI>80, PF>0.90 THD<20% @ 240v Ac. An operating voltage Range of 140-270V including all connection upto ceiling rose complete all as specified and directed.

S&F in repairs Wall mounted LED Integrated Batten 10 Watt-2 Ft White, indoor decorative PVC extruded LED batten, complete.

S&F in repairs Modular AC Box with socket and MCB SP 25 Amp complete with Metal box , white colour plate and frame complete in replacement of sheet metal enclosures as per site requirement , complete all as specified and directed.

S&F in repairs switch molular type 1M 16 Amp with red indication light complete all as specified and directed. Note : Eectric switch of geyser of 16 Apms shall be provided on main switch board of the bathroom and socket outlet shall be provide near the geyser and will be measured as 16 Amps power point wiring against item No 5.

S&F in repairs lamp holder angle batten type bakelite insoluated body with back place complete all as specified and directed.

S&F in repairs LED lamp 12 Watt LED Bulb complete all as specified and directed.

S&F in repairs of electric bell Ding Dong type AC, 230 volts single phase all as specified.

S&F in repairs ceiling rose surface Bakelite 65x25mm two to three terminals complete all as specified.

S&F in repairs LED bulk head in engineering plastic housing with clear prismatic diffuser, 10W WHITE in replacement of old unsv bulk head fitting including all accessories connecting up twin core flexible copper conductor cable complete all as directed. Make: Make- Havells Cat Part No - HEXAFT10WLED857SSYMBOPC / Crompton Cat Part No- LBHE-10-CDL / Wipro Cat Part No- WP1099.

S&F in repairs of building security light fitting 30W LED 5000K new Powder coated pressure die cast aluminium compact LED Street light including pole of suitable dia bracket duly fixed with clamps, nut, bolts & washers etc and all as directed.

S&F in repairs for stepped type electronic fan regulator modular type, 100W 2 module.

Supply, Installation, testing and commissioning of 1200mm sweep BEE 5 star rated, Ceiling fan with Brush Less Direct Current (BLDC) Motor, Class of insulation : B, 3 Nos Blade, 30 cm long down road, 2 Nos canopies, shackle kit, safety rope, copper winding, power factor not less than 0.9, service value (CMM/W) minimum 6.85, Air delivery not less than 220 CMM, 350 RPM (tolerance as per IS:374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nuts bolts, washers, temperature rise =75 degree C (maximum), insulation resistance more than 2 mega Ohm, suitable for 230V, 50 Hz, single phase AC supply complete all as specified and directed by Engr-in-Charge including taking down old ceiling fan and depositing to MES store yard. Note : All unsv ceiling fan shall be deposited to MES Store Yard.

S&F Exhaust Fan, Metal body, copper wound 300 mm Sweep, with louvers including taking down of old exhasut fan and depositing to MES store yard and connecting up with replacement of cable T/C flexible cable of size:- 0.50 Sqmm from ceiling rose / connection to fan all as specified and directed. Note : All unsv Exhaust fan shall be deposited to MES Store Yard.

S&F Exhaust Fan, Made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz RPM 1200 copper winding 300 mm Sweep complete all as specified and directed. Note for item No 145 & 146 :- (i) The rate is inclusive of drilling hole of suitable size for exhaust fan/cutting/chasing and making good the disturbed surface with cm 1:3 and same surface finishes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete. (ii) All unsv ceiling fan shall be deposited to MES Store Yard.

S&F Hot Water Storage (Geyser) 25 Ltrs Capacity metal body, BEE 5 Star Rated, including taking down of old geyser of 50 Ltr capacity (04 Nos) and depositing to MES store yard and connecting up the geyser with replacement of cable three core cable of size 1.50 Sqmm by means of plug top 20 Amps all as specified and directed.

30. S&F in repairs of VTPN DB 4 way double door, vertical type for fixing MCCB up to 250 Amps as incommer and MCBs as out goings with metel door and IP 43 Protections and connecting with external electric supply cable 3 Phase complete all as of approved make by the GE. Note :- Quoted rate includes digging up 3 Phase cable loop near VTPN DB and connecting to VTPN DB complete. Make :L&T/Havells/Indoasian/ Siemens/Legrand as approved)

S&F in repairs of sheet metal enclosures double door for DBs when MCBs to be used SPN-8 Way, 240V with 200 Amp rated busbar complete as per site requirement and as directed by Engr-in charge.

S&F in repairs for MCB SP 63 Amps 240 Volts, 10KA, `B' curve all as per site requirement and as directed. (Make: L&T/Legrand/Siemens/Havells as approved).

32. M&L in repairs of MCCB 4 Pole .415 V. fixed type, 125 Amps with breaking capacity 16kA all as directed (Make: Legrand/L&T/Havells/ Siemens as approved).

S&F in repairs MCB SPN 40 Amps 'B' series, breaking capacity 10 KA, 'B' curve 240 volts, 50 Hz including necessary incoming and out going electric connection all as per site requirement and as directed. . (Make: Legrand/ Siemens/L&T/Havells/)

S&F in repairs for MCB SP 6 to 32 Amps 240 Volts, 10kA, `B' curve all as per site requirement and as directed. (Make: L&T/Legrand/Siemens/Havells as approved).

M&L in repairs for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to GI wire 4 mm as earthing lead by means of nut, bolts and check nuts and washers, GI light grade protection pipe 15 mm dia upto 7.5 M, GI watering pipe 20 mm dia medium grade, RCC cover with funnel, excavation in any type of soil, PCC pit charcoal, salt all as shown in electrical plate No 5 of SSR Part I, including earth test point upto panel board, all as specified or indicated including testing on completion.

S&F in repairs Sheet metal enclosure of size 300 x 250 x 150 mm suitable for mounting Pre paid meter fabricated from CRCA sheet with anti corrosive dust and vermin proof. Note:- The meter cover shall have a transparent window. The window shall be of transparent, high grade UV stabilized engineering plastic for easy reading of all the displayed values/parameters and observation of operation indicator. The window shall preferably be an integral part of meter cover all as specified and directed.

Taking down and refixing Prepaid meter and Monitoring device with consultation with prepaid meter authorities including passing existing 3 pair cable from prepaid meter to monitoring device through PVC concealed conduit and necessary connections and testing on completion of work. Note - The rates are inclusive of Cutting / chasing and making good to disturbed surface with CM 1: 3 and same surface finishes with the adjoining surface of disturbed area with OBD / Colour wash /white wash complete.

Taking down unserviceable sub main wiring of any size complete and making good disturbed surface complete all as specified and directed.

M&L for Sub Main wiring using single run PVC FRLS grade Insulated unsheathed, multistrand copper conductor cable 2 runs of 10 Sqmm for phase and neutral and 1 run of 10 Sqmm for earth wire drawn through concealed PVC conduit wiring in wall not less than 25mm dia with all fittings like tees, bends, junction/ terminal boxes etc as per site requirement and all as directed by Engr-in-charge. (Note:- Phase should be of Red /Yellow/Blue, neutral should be of back and earthing wire should be of green colour. 2 runs of cable for phase/ neutral and 1 run for earth will be measured and paid as one unit length).

S&F wall mounted fully automatic filterless kitchen chimeny made of stainless steel in size range 60 cm to 90 cm good for 2-3 gas burners of suction capacity not less than 1200 mtr cub/hrs touch, gesture control filterless autoclean including all connecting accessories outet pipe etc complete all as specified and as directed. Note : Work for fitting of chimney including hole/pipe of suitable size for outlet shall be done by Contractor. Make : Glen-Electric, Faber, Hindware

S&F wall mounted Fan, made of strudy engineering plastic complete voltage 230 Vol/50 Hz copper winding of sweep size 300mm complete all as specified and as directed.

S&F PVC conduit medium grade of size 20mm TV connection and socket /Telephone socket complete all as specified and as directed.

S&F TV Co-Axial socket 1 module complete all as specified and as directed.

S&F Telephone socket 1 module complete all as specified and as directed.

S&F Flush metal box 1 module complete all as specified and as directed.

S&F white cover plate with frame 1 module complete all as specified and directed.

Note :- The contract sum shall be after deducting the amount of credit shown in Sch of Credit of this tender

HANUMAN BUILDERS (BID ID -3077896)

P R Constructions (BID ID -3066922)

YP INFRA (BID ID -3078481)

M/S Parmod Johar (BID ID -3067540)

M/S GOPAL JEE SINGH (BID ID -3078832)