LED Luminaire (for Flood Light)

LED Luminaire (for Flood Light)

LED Luminaire (for Flood Light) LED Luminaire (for Flood Light) ( 50 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 50W 15W

20W

25W

30W

40 W

50W

55W

60W

70W

75W

80W

90W

100W

1 20W

125W

150W

200W

250W

300W

350W

400 W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - 1/17 Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - 2/17 Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a Yes - 3/17 weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

water

insects etc.

Luminaries light transparency should be of Toughened glass Yes - Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes - Number of electronic control gear (power supplies) 1 No. 1 No.

2 Nos.

3 Nos.

4 Nos. Driver components shall be industrial grade or above Yes - PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes - The Luminaires works on single phase three wires system (Phase

Neutral and Earth) Yes - Suitable connector shall be provided for LED connection between driver output and LED Yes - Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm - Light Source SMD LED Chip as per LM 80/IS16106 - MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed - Manufacturer’s name

model number

serial number Yes - Date of manufacture (month-year)

and lot Yes - 4/17 number as identification mark inside each unit and the outside of each packaging box The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

power

PF

Current in Amps

CRI & CCT etc.

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Yes - 5/17 Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mukesh Shukla 492001

O/o Executive Engineer

(E&M) Public Works Department Sirpur Bhawan Parisar

Raipur. (C.G.) 50 15 LED Luminaire (for Flood Light) ( 14 ) Technical Specifications Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire Type B - 6/17 as per the IS: 16107(Part-2 Sec.-1)/2012 Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 100W 15W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes - OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - 7/17 Optic lense materal (UV stabilised) (Write NA for without optic lense supply) Poly carbonate lense - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against surges and transients of >/=10KV (External) No - CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - 8/17 All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

Yes - Luminaries light transparency should be of Toughened glass Yes - Toughned transparent glass cover thickness >/=4 mm - Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes - Number of electronic control gear (power supplies) 1 No. 1 No.

Neutral and Earth) Yes - Suitable connector shall be provided for LED connection between driver output and LED Yes - Length of ISI marked three core wire (shall be provided along with 50 cm - 9/17 supply of material) Light Source SMD LED Chip as per LM 80/IS16106 - MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed - Manufacturer’s name

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

) Yes - LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological Yes - 10/17 report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mukesh Shukla 492001

Raipur. (C.G.) 14 15 LED Luminaire (for Flood Light) ( 50 ) Technical Specifications 11/17 Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes - Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes - Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B - Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 - LED Rating/System Wattage/Rated Power 100W 15W

500W Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt - Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 - Mounting brackets (included) Adjustable - Warranty for free replacement (in Years) 2 - ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz - Automatic Higher Cut off voltage above 300 volt Yes - Rated voltage 230 V AC 50 Hz - AC Power Factor at full load ≥ 0.95 - Driver Efficiency (in %age) ≥85 - Total Harmonics Distortion (in %age) ≤ 10 - "The total circuit power shall not be more than 110 percent of the value declared by the Yes - 12/17 manufacturer" OPTICAL LED chip Efficacy ≥130 Lm/Watt - Colour temperature (+/-500K) 6000K - Working life for LED (Minimum 50

000 burning hours as per LM-80 report) Yes - Colour Rendering Index(CRI) ≥70 - Beam Angle ≥120 - Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA - THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes - Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes - Junction temperature < 85 degC - Operating temperature range -10 deg C to +55 deg C - Operating Humidity Range 10 % to 95% RH - PROTECTION Short circuit Protection Yes - Over load protecton Yes - Over Voltage protection Yes - Reverse polarity Yes - High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes - Insulation resistance between earth and current carrying part >100 M ohm - The luminaire shall be protected against surges and transients ( Internal) >/=4KV - The luminaire shall be protected against No - 13/17 surges and transients of >/=10KV (External) CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes - The luminaire body must be corrosion resistant epoxy powder coated Yes - All fastners must be of stainless steel Yes - The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes - Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust

4 Nos. Driver components shall be industrial grade or above Yes - PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes - 14/17 The Luminaires works on single phase three wires system (Phase

and lot number as identification mark inside each unit and the outside of each packaging box Yes - The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes - REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND - System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes - LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Yes - 15/17 lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output

) LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes - Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes - Seller has to furnish Type test report on demand by buyer/consignee Yes - DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes - LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes - * Bold specifications are the golden parameters. Consignees and Quantity 16/17 S.No. Consignee Address Quantity Delivery Days 1 Mukesh Shukla 492001

Raipur. (C.G.) 50 15 EMD Required No ePBG Required No