Special Repair of Urban Health Center Sector-25 at Panipat (Re-Invited)

Amount

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement (HSR 8.5 b)

Stripping and stacking slates or tiles of a roof (HSR 8.10)

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantled (HSR 8.18) a) Door

b) Window

Dismantling brick or flagged stone slab flooring including concrete base (HSR 8.27)

Cement Concrete 1:4:8 with brick ballast 40mm nominal size in foundation and plinth.(HSR 10.36)

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. (HSR 10.38)

Cement Concrete 1: 1 ½: 3 with stone aggregate 20mm nominal size in foundation and plinth (HSR 10.42)

Cement concrete 1:1½ :3with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respect (HSR 10.82+10.95a)

First class brickwork laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level. (HSR 11.7)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean (HSR 13.14)

Tile terracing with one layer of tiles, 22.86 cm X 11.43 cm X 3.81 cm laid dry over a layer of mud mortar including grouting with cement sand mortar 1: 3 and top surface to be left clean (HSR 13.14) (L.R.)

Corrugated G.I. sheet roofing 0.80 mm thick fixed with galvanised iron ‘J’ or ‘L’ hooks, 10 mm dia G.I. limpet and bitumen washers complete, excluding the cost of purlins, rafters and trusses.(HSR 13.18)

Conglomerate floor 50 mm thick cement concrete topping 1:2:4 (HSR 14.10)

Prov. And Fixing. Vitrified Tiles Size 600x600 mm approved making flooring in any pattern as specified over base of 20mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry with pigment to match the shade to tiles. Note:- Tile shall be premium quality (first quality) of reputed manufacture like: NITCO, KAJARIA, SOMANI, ORIENT, JHONSON & RAK AND SIMPOLO (HSR 14.89)

Providing and fixing 1st quality ceramic glazed wall tiles of size 12"x18" confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting risers of steps and dado over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92 (b))

12 mm thick cement plaster 1:4 (HSR 15.5)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Applying priming coat with metal primer on new steel or iron work including preparation of surface. (HSR 16.9)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work (HSR 16.57)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79 b)

Supplying and fixing glass panes with moulding of commercial hard wood such as hollock, champ, chikrassy and chaplash etc.(Non coniferous timber other than teak, conforming to I.S. specification No.1003, kiln seasoned). (c) 4 mm thick (glazing area above 55 sq dm, but upto 84 sq dm of each pane) (HSR 17.36c)

Structural steel work in angles, tees and flats, welded including cutting fixing all gusset plates, bolts, nuts, welding rod, etc., with hoisting and erecting in position:- For roof trusses, well kerbs, plates and trussed girders, etc., of any span for buildings and bridges (HSR 18.7)

Wrought iron and mild steel (using angles, flats, square bars, tees and channels) ladders, grills, gratting frames, window guards, iron doors open able or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. (HSR 18.12)

Providing and fixing in position collapsible steel shutters, with vertical channels 20 mm X 10 mm X 2 mm and braced with flat iron diagonal 20 mm X 5 mm size, with top and bottom rails of T-iron 40 mm X 40mm X 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, etc., complete. (HSR 18.20)

Fe- 500 EQR TMT steel bars for RCC works where not including in the complete rate of RCC including bending and placing in position complete (N.S)

LABOUR FOR LAYING JOINTING, FIXING AND TESTING G.I./P.V.C./ W.I.PIPE LINES AND SPECIALS tees bends, sockets elbows etc., INSIDE BUILDING and testing etc., complete including cutting threading.(HSR 28.18 (vi)

Round G.I. Pipe 2" Dia

Recovery Items 1. Good Brick/Tiles @ 4.50 Each

2. Brick Bats @ 450 Per Cum

3. Door @ 800 Each

4. Window @ 500 Each

The Quality Coop Society Ltd