Loading…
Loading…
Tender Value
₹11.7 Cr
EMD Value
₹7.4 L
Closing Date
25 Jul 2025, 3:00 pmClosed
Part "A" Jhansi Division:- Civil engineering work for Proposal for splitting of longer block section by providing loop lines on either side of main line by converting Rajnagar D-class into B-class station between Singhpur Dumra and Khajuraho stations. Part "B" Jhansi Division: Extension/Raising of PF no. 1 to high level for recoupment of shortfall in MEA at KHGP under LAR-KURJ section. Part "C" Jhansi Division: Extension/Raising of PF no. 1 & Raising of PF no.2 to high level for recoupment of shortfall in MEA at UDPR in LAR-KURJ section under ADEN/MBA.
JHS-ENGG-E-2025-113
JHS-ENGG-E-2025-113
Open
15 Months
Jhansi, Uttar Pradesh
₹0
₹7.4 L
27 Jun 2025
27 Jun 2025
Item- 7 Part "C" All items of CPWD DSR 2021 Chapter No. 2,4,5,6,8,9,10,11,12, 13,16, 17,18,19 & 21.
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
S No. Item No Description of Item Unit Qty Rate Amount
2.0 EARTH WORK
Earth work in excavation by
mechanical means (Hydraulic
excavator)/manual means over
areas (exceeding 30 cm in depth,
2.6 1.5 m in width as well as 10 sqm on
plan) including getting out and
disposal of excavated earth lead
upto 50 m and lift upto 1.5 m, as
directed by Engineer-in-charge.
4.0 CONCRETE WORK
4.1S CEMENT CONCRETE (CAST IN SITU)
Providing and laying in position
cement concrete of specified grade
4.1 excluding the cost of centering and
shuttering - All work up to plinth
(zone-III) derived from natural
2 sources : 3 graded stone aggregate
20 mm nominal size derived from
natural sources)
( z o n e - I I I ) derived from natural
3 sources : 6 graded stone aggregate
20 mm nominal size derived from
natural sources)
5.0 REINFORCED CEMENT CONCRETE
5.9S FORM WORK
Centering and shuttering including
5.9 strutting, propping etc. and removal
5.9.1 Foundations, footings, bases of Sqm 350 307.95 107782.5
columns, etc. for mass concrete
5.9.2 Walls (any thickness) including Sqm 700 669.55 468685
5 attached pilasters, butteresses,
plinth and string courses etc.
5.9.3 Suspended floors, roofs, landings, Sqm 70 766.55 53658.5
balconies and access platform
girders, bressumers and cantilevers
5.9.6 Columns, Pillars, Piers, Abutments, Sqm 25 804.25 20106.25
Posts and Struts
5.22S STEEL REINFORCEMENT
Steel reinforcement for R.C.C. work
including straightening, cutting,
5.22 bending, placing in position and
binding all complete upto plinth
5.22.6 Thermo-Mechanically Treated bars Kg 17500 89.65 1568875
of grade Fe-500D or more.
5.33S DESIGN MIX CONCRETE
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Providing and laying in position
ready mixed or site batched design
mix cement concrete for reinforced
cement concrete work; using coarse
aggregate and fine aggregate
derived from natural sources,
Portland Pozzolana / Ordinary
Portland /Portland Slag cement,
admixtures in recommended
proportions as per IS: 9103 to
accelerate / retard setting of
concrete, to improve durability and
w o r k a b i l i t y without impairing
s t r e n g t h ; including pumping of
concrete to site of laying, curing,
carriage for all leads; but excluding
the cost of centering, shuttering,
finishing and reinforcement as per
direction of the engineer-in-charge;
for the following grades of concrete.
Note: Extra cement up to 10% of the
minimum specified cement content
in design mix shall be payable
separately. In case the cement
content in design mix is more than
1.10 times of the specified minimum
cement content, the contractor shall
have discretion to either re-design
the mix or bear the cost of extra
5.33.1 All works upto plinth level
10 minimum cement content of 330 kg
All works above plinth level upto
11 minimum cement content of 330 kg
5.35 Add for using extra cement in the Quintal 45 688.45 30980.25
items of design mix over and above
the specified cement content
6.0 MASONRY WORK
Brick work with common burnt clay
F.P.S. (non modular) bricks of class
designation 7.5 in foundation and
Brick work with common burnt clay
F.P.S. (non modular) bricks of class
6.4 designation 7.5 in superstructure
above plinth level up to floor V level
in all shapes and sizes in :
8.0 CLADDING WORK
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Providing and fixing 18 mm thick
gang saw cut, mirror polished,
premoulded and prepolished,
machine cut for kitchen platforms,
vanity counters, window sills, facias
and similar locations of required
size, approved shade, colour and
8.2 texture laid over 20 mm thick base
cement mortar 1:4 (1 cement : 4
coarse sand), joints treated with
white cement, mixed with matching
pigment, epoxy touch ups, including
rubbing, curing, moulding and
polishing of edges to give high gloss
finish etc. complete at all levels.
Granite stone slab of colour black,
Cherry/Ruby red
8.20S STONE WORK DRY CLADDING
8.31 Providing and fixing Ist quality Sqm 50 1063.45 53172.5
ceramic glazed wall tiles conforming
to IS: 15622 (thickness to be
specified by the manufacturer), of
approved make, in all colours,
shades except burgundy, bottle
green, black of any size as approved
17 by Engineer-in-Charge, in skirting,
risers of steps and dados, over 12
mm thick bed of cement mortar 1:3
(1 cement : 3 coarse sand) and
jointing with grey cement slurry @
3.3kg per sqm, including pointing in
white cement mixed with pigment of
matching shade complete.
9.0 WOOD AND P.V.C. WORK
Providing and fixing 25 mm thick
shutters for cup board etc. :
Providing and fixing ISI marked flush
door shutters conforming to IS :
2202 (Part I) non-decorative type,
core of block board construction
9.21 with frame of 1st class hard wood
and well matched commercial 3 ply
veneering with vertical grains or
cross bands and face veneers on
both faces of shutters:
18 Stainless Steel butt hinges with
necessary screws
9.40S MISCELLANEOUS-WOOD WORK
Providing and fixing M.S. grills of
required pattern in frames of
windows etc. with M.S. flats, square
or round bars etc. including priming
coat with approved steel primer all
ANODISED ALUMINIUM FITTINGS
9.95S (ALL FITTINGS SHALL BE ISI
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Providing and fixing aluminium
sliding door bolts, ISI marked
anodised (anodic coating not less
9.96 than grade AC 10 as per IS : 1868),
transparent or dyed to required
colour or shade, with nuts and
screws etc. complete :
Providing and fixing aluminium
tower bolts, ISI marked, anodised
(anodic coating not less than grade
9.97 AC 10 as per IS : 1868 ) transparent
or dyed to required colour or shade,
with necessary screws etc. complete
Providing and fixing aluminium
handles, ISI marked, anodised
(anodic coating not less than grade
9.100 AC 10 as per IS : 1868) transparent
or dyed to required colour or shade,
with necessary screws etc. complete
Providing and fixing aluminium
hanging floor door stopper, ISI
marked, anodised (anodic coating
9.101 not less than grade AC 10 as per IS :
1868) transparent or dyed to
required colour and shade, with
necessary screws etc. complete.
10.0 STEEL WORK
10.2 Structural steel work riveted, bolted Kg 10000 111.95 1119500
or welded in built up sections,
trusses and framed work, including
cutting, hoisting, fixing in position
and applying a priming coat of
approved steel primer all complete.
Providing and fixing 1mm thick M.S.
sheet door with frame of 40x40x6
mm angle iron and 3 mm M.S.
gusset plates at the junctions and
corners, all necessary fittings
complete, including applying a
priming coat of approved steel
diagonal braces
Providing and fixing T-iron frames
for doors, windows and ventilators of
mild steel Tee-sections, joints mitred
10.13 and welded, including fixing of
necessary butt hinges and screws
and applying a priming coat of
approved steel primer.
long embedded in cement concrete
block 15x10x10 cm of C.C. 1:3:6 (1
Cement : 3 coarse sand : 6 graded
stone aggregate 20 mm nominal
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Steel work welded in built up
sections/ framed work, including
cutting, hoisting, fixing in position
and applying a priming coat of
approved steel primer using
structural steel etc. as required.
27 ladder, railings, brackets, gates and
10.28 Providing and fixing stainless steel ( Kg 750 612.25 459187.5
Grade 304) railing made of Hollow
tubes, channels, plates etc.,
including welding, grinding, buffing,
polishing and making curvature
(wherever required) and fitting the
same with necessary stainless steel
nuts and bolts complete, i/c fixing
the railing with necessary
accessories & stainless steel dash
fasteners , stainless steel bolts etc.,
of required size, on the top of the
floor or the side of waist slab with
suitable arrangement as per
approval of Engineer-in-charge, (for
payment purpose only weight of
stainless steel members shall be
considered excluding fixing
accessories such as nuts, bolts,
fasteners etc.).
11.0 FLOORING
1:2:4 (1 cement : 2 coarse sand : 4
29 graded stone aggregate 20 mm
nominal size), including finishing
11.16S TILE FLOORING
Chequerred precast cement
concrete tiles 22 mm thick in
footpath & courtyard, jointed with
neat cement slurry mixed with
11.20 pigment to match the shade of tiles,
including rubbing and cleaning etc.
complete, on 20 mm thick bed of
cement mortar 1:4 (1 cement: 4
11.20.1 Light shade pigment using white Sqm 450 1233.05 554872.5
11.26S KOTA STONE FLOORING
Kota stone slab flooring over 20 mm
(average) thick base laid over and
jointed with grey cement slurry
mixed with pigment to match the
shade of the slab, including rubbing
and polishing complete with base of
cement mortar 1 : 4 (1 cement : 4
11.37S CERAMIC GLAZED TILES
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
11.38 Providing and laying Ceramic glazed Sqm 110 1107.05 121775.5
floor tiles of size 300x300 mm
(thickness to be specified by the
manufacturer), of 1st quality
conforming to IS : 15622, of
approved make, in all colours,
shades, except White, Ivory, Grey,
Fume Red Brown, laid on 20 mm
thick bed of cement mortar 1:4 (1
Cement : 4 Coarse sand), jointing
with grey cement slurry @ 3.3 kg/
sq.m including pointing the joints
with white cement and matching
pigments etc., complete.
11.41S VITRIFIED FLOOR TILES
Providing and laying vitrified floor
tiles in different sizes (thickness to
be specified by the manufacturer)
with water absorption less than
0.08% and conforming to IS: 15622,
of approved make, in all colours and
11.41 shades, laid on 20mm thick cement
mortar 1:4 (1 cement : 4 coarse
sand), jointing with grey cement
slurry @ 3.3 kg/ sqm including
grouting the joints with white
cement and matching pigments etc.,
12.0 ROOFING
Providing, fixing and embedding
sand cast iron accessories for rain
water pipes in the masonry
12.40 surrounded with 12 mm thick
cement mortar of the same mix, as
that of masonry (lead caulking will
be paid for separately):
Providing and fixing on wall face
unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type
12.41 A, including jointing with seal ring
conforming to IS : 5382, leaving 10
mm gap for thermal expansion, (i)
Single socketed pipes.
Providing and fixing on wall face
unplasticised - PVC moulded fittings/
accessories for unplasticised Rigid
PVC rain water pipes conforming to
IS : 13592 Type A, including jointing
with seal ring conforming to IS :
5382, leaving 10 mm gap for
thermal expansion.
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
12.50 Providing and fixing precoated Sqm 400 671.55 268620
galvanised iron profile sheets (size,
shape and pitch of corrugation as
approved by Engineer-in-charge)
0.50 mm (+ 0.05 %) total coated
thickness with zinc coating 120
grams per sqm as per IS: 277, in 240
mpa steel grade, 5-7 microns epoxy
primer on both side of the sheet and
polyester top coat 15-18 microns.
Sheet should have protective guard
film of 25 microns minimum to avoid
scratches during transportation and
should be supplied in single length
upto 12 metre or as desired by
Engineer-in-charge. The sheet shall
be fixed using self drilling /self
tapping screws of size (5.5x 55 mm)
with EPDM seal, complete upto any
pitch in horizontal/ vertical or curved
surfaces, excluding the cost of
purlins, rafters and trusses and
including cutting to size and shape
wherever required.
13.0 FINISHING
13.1S CEMENT PLASTER (IN FINE SAND)
13.1 12 mm cement plaster of mix :
13.16S 6MM CEMENT PLASTER
13.44S EXTERIOR FINISHING
Finishing with Deluxe Multi surface
paint system for interiors and
exteriors using Primer as per
manufacturers specifications :
13.48.1 Two or more coats applied on walls Sqm 300 158.95 47685
@ 1.25 ltr/10 sqm over and
including one coat of Special primer
applied @ 0.75 ltr /10 sqm
13.48.3 Painting Steel work with Deluxe Sqm 100 140.05 14005
Multi Surface Paint to give an even
shade. Two or more coat applied @
0.90 ltr/10 sqm over an under coat
of primer applied @ 0.80 ltr/10 sqm
of approved brand and manufacture
cement based putty of average
thickness 1 mm, of approved brand
and manufacturer, over the
plastered wall surface to prepare the
surface even and smooth complete.
16.0 ROAD WORK
16.1S ROADS
16.3 Supplying and stacking at site.
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
16.4 Laying, spreading and compacting cum 1000 865.8 865800
stone aggregate of specified sizes to
WBM specifications in uniform
thickness, hand picking, rolling with
3 wheeled road/vibratory roller 8-10
tonne capacity in stages to proper
grade and camber, applying and
brooming requisite type of screening
/ binding material to fill up
interstices of coarse aggregate,
watering and compacting to the
required density .
16.49S MISCELLANEOUS
Providing and laying factory made
chamfered edge Cement Concrete
paver blocks in footpath, parks,
lawns, drive ways or light traffic
parking etc, of required strength,
thickness & size/ shape, made by
table vibratory method using PU
mould, laid in required colour &
pattern over 50mm thick compacted
16.91 bed of sand, compacting and proper
embedding/laying of inter locking
paver blocks into the sand bedding
layer through vibratory compaction
by using plate vibrator, filling the
joints with sand and cutting of paver
blocks as per required size and
pattern, finishing and sweeping
extra sand. complete all as per
direction of Engineer-in-Charge.
43 30 grade with approved color design
17.0 SANITARY INSTALLATIONS
Providing and fixing water closet
squatting pan (Indian type W.C. pan
) with 100 mm sand cast Iron P or S
trap, 10 litre low level white P.V.C.
flushing cistern, including flush pipe,
17.1 with manually controlled device
(handle lever) conforming to IS :
7231, with all fittings and fixtures
complete, including cutting and
making good the walls and floors
wherever required:
17.1.1 White Vitreous china Orissa pattern Each 2 5781.35 11562.7
44 W.C. pan of size 580x440 mm with
integral type foot rests
Providing and fixing white vitreous
china pedestal type water closet
(European type W.C. pan) with seat
and lid, 10 litre low level white
P.V.C. flushing cistern, including
17.2 flush pipe, with manually controlled
device (handle lever), conforming to
IS : 7231, with all fittings and
fixtures complete, including cutting
and making good the walls and
floors wherever required :
17.2.1 W.C. pan with ISI marked white solid Each 2 5540.55 11081.1
plastic seat and lid
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Providing and fixing white vitreous
china flat back or wall corner type
lipped front urinal basin of
340x410x265 mm sizes respectively
with automatic flushing cistern with
standard flush pipe and C.P. brass
spreaders with brass unions and G.I
clamps complete, including painting
of fittings and brackets, cutting and
making good the walls and floors
wherever required :
17.4.1 One urinal basin with 5 litre white Each 2 5268.85 10537.7
P.V.C. automatic flushing cistern
Providing and fixing wash basin with
C.I. brackets, 15 mm C.P. brass pillar
taps, 32 mm C.P. brass waste of
17.7 standard pattern, including painting
of fittings and brackets, cutting and
making good the walls wherever
17.7.3 White Vitreous China Wash basin Each 2 2040.85 4081.7
47 size 550x400 mm with a pair of 15
mm C.P. brass pillar taps
Providing and fixing P.V.C. waste
17.28 pipe for sink or wash basin including
P.V.C. waste fittings complete.
17.28.1 Semi rigid pipe
beveled edge mirror of superior
glass (of approved quality) complete
with 6 mm thick hard board ground
fixed to wooden cleats with C.P.
brass screws and washers complete.
18.0 WATER SUPPLY
18.7S C.P.V.C. PIPES
Providing and fixing G.I. Pipes
complete with G.I. fittings and
clamps, i/c making good the walls
18.11 etc. concealed pipe, including
painting with anti corrosive
bitumastic paint, cutting chases and
making good the wall :
Providing and fixing G.I. pipes
complete with G.I. fittings including
trenching and refilling etc.-External
18.15S BRASS FITTINGS
Providing and fixing gun metal gate
18.17 valve with C.I. wheel of approved
quality (screwed end) :
Providing and fixing ball valve
(brass) of approved quality, High or
low pressure, with plastic floats
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Providing and fixing gun metal non-
18.19 return valve of approved quality
(screwed end) :
18.19.4 50 mm nominal bore
Providing and fixing uplasticised PVC
connection pipe with brass unions :
C.I. SLUICE VALVES/ FIRE HYDRANTS
Boring with 100 mm diameter
casing pipe for hand pump /
tubewell, in all soils except ordinary
18.42 hard rocks requiring blasting,
including removing the casing pipe
after the hand pump / tube well is
lowered and tested :
18.43 Providing and placing in position Metre 20 813.25 16265
filters of 40 mm diameter G.I. pipe
with brass strainer of approved
18.44 Providing and fixing to filter and Metre 20 499.8 9996
lowering to proper levels 40 mm G.I.
pipe for tube well including cleaning
and priming the tube well.
18.45 Providing and placing in position Each 1 1178.65 1178.65
hand pump of approved quality for
40 mm diameter G.I. pipe complete
with all accessories.
Providing and fixing G.I. Union in G.I.
pipe including cutting and threading
the pipe and making long screws
etc. complete (New work) :
18.48 Providing and placing on terrace (at Litre 5000 9.7 48500
all floor levels) polyethylene water
storage tank, IS : 12701 marked,
with cover and suitable locking
arrangement and making necessary
holes for inlet, outlet and overflow
pipes but without fittings and the
base support for tank.
18.49S C.P. BRASS FITTINGS
Providing and fixing C.P. brass bib
18.49 cock of approved quality conforming
Providing and fixing C.P. brass stop
cock (concealed) of standard design
and of approved make conforming to
Providing and fixing C.P. brass angle
valve for basin mixer and geyser
points of approved quality
conforming to IS:8931
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
18.54S PTMT FITTINGS
Providing and fixing PTMT, push cock
of approved quality and colour.
weighing not less than 75 gms
19.0 DRAINAGE
19.1S STONE WARE PIPES AND FITTINGS
Providing, laying and jointing glazed
stoneware pipes class SP-1 with stiff
mixture of cement mortar in the
proportion of 1:1 (1 cement : 1 fine
sand) including testing of joints etc.
Providing and laying cement
concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate
40 mm nominal size) all-round S.W.
pipes including bed concrete as per
standard design :
21.0 ALUMINIUM WORK
Providing and fixing aluminium work
for doors, windows, ventilators and
partitions with extruded built up
standard tubular sections/
appropriate Z sections and other
sections of approved make
conforming to IS: 733 and IS: 1285,
fixing with dash fasteners of
required dia and size, including
necessary filling up the gaps at
junctions, i.e. at top, bottom and
sides with required EPDM rubber/
neoprene gasket etc. Aluminium
sections shall be smooth, rust free,
straight, mitred and jointed
mechanically wherever required
including cleat angle, Aluminium
snap beading for glazing / paneling,
C.P. brass / stainless steel screws, all
complete as per architectural
drawings and the directions of
Engineer-in-charge. (Glazing,
paneling and dash fasteners to be
paid for separately) :
21.1.1 For fixed portion
78 thickness of powder coating 50
Providing and fixing glazing in
aluminium door, window, ventilator
shutters and partitions etc. with
EPDM rubber / neoprene gasket etc.
21.3 complete as per the architectural
drawings and the directions of
engineer-in-charge . (Cost of
aluminium snap beading shall be
paid in basic item):
79 thickness (weight not less than
Schedule Schedule 8-Part "C" All items of USSOR 2021 chapter No. 01,02 & 05.
Item- 8 Part "C" All items of USSOR 2021 chapter No. 01,02 & 05.
S No. Item No Description of Item Unit Qty Rate Amount
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
Earthwork in filling in embankment,
guide bunds, around buried type
abutments, bridge gaps, trolley
refuges, platforms etc. with
contractor's own earth conforming
to Soil Quality Class SQ1/SQ2/SQ3,
after preparation of foundations as
applicable, benching in existing
banks wherever required, spreading
in layers with motor grader, bringing
the moisture content to OMC,
mechanical compaction to specified
density and dressing of bank to final
profile as per RDSO Specifications:
RDSO/2020/GE: IRS-0004 with latest
correction slips. Note: 1) Foundation
preparation, Benching including
additional earthwork on account of
this, wherever required, shall be
paid extra under relevant schedule
item for benching. 2) Payment for
Earthwork under this item shall be
made based on the cross section
measurements calculated (i) with
original ground profile of existing
bank based on initial ground levels
before doing benching and (ii) final
profile of the bank worked out with
final levels as per prevailing
blanketing material by wet mixing of
different types of naturally available
suitable soil including additional
blending with naturally available or
manufactured material as required
to achieve specified gradation, in
designed proportion in Pug mill or
wet mix plant to have uniform
gradation as per RDSO Specification
No. RDSO/2020/GE: IRS-0004 with
latest correction slips including all
incidental transportation and
stacking at site in Stacks. Note:
Measurement shall be done in as per
Stack measurement.
Supply and using Cement at
approved brands/makes
Stone Boulders, weighing not less
than 35kg each with voids filled with
cement sand mortar 1:4 on slopes
laid over prepared filter media
including boulder apron laid dry in
front of toe of embankment
complete as per drawing and
Technical Specifications (filter media
to be paid separately under the
relevant item). Rate is excluding
cost of cement which shall be paid
extra under relevant item.
Schedule Schedule 9-Part "C" NS Items
Item- 9 Part "C" NS Items
S No. Item No Description of Item Unit Qty Rate Amount
JHANSI DIVISION-ENGG/NORTH CENTRAL RLY
supplying & fixing of pr-fabricated
RCC coping stone of size 530mm x
1125mm x 100mm thick as per top
face designed and approved by site
Engineer with M-30 grade RCC with
8 mm dia. tor steel at 150mm c/c
both ways and manufactured by
vibro compaction process using
jointless FRP/GRP steel moulds of
required size, shape & design. The
item includes cost of cement,
reinforcement, transportation etc
complete in all respect.
position M25Grade Reinforced
cement concrete in Precast standard
Platform wall sections, including the
cost of centering, shuttering,
finishing, Admixtures in
recommended proportion (as per IS
9103) t o accelerate, retard setting
of concrete, improve work ability
without impairing strength and
durability but excluding the cost of
cement and steel reinforcement, as
per approved plan & as per direction
of the Engineer in-charge.
Tactile tiles 300x300 size on floor on
20mm thick 1:4 mortar bed
including pointing with matching
color cement etc. including all
material, labour, freight & all taxes
complete as per satisfaction of
Engineer incharge.
Download all tender documents and submit your bid