Establishment of 21 nos. new Polytechnics in different district of Assam under plan during 2011-12 at Golokganj (Agomoni revenue circle) in Dhubri District

Amount

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified upto a depth of 2.00 m below the existing G.L. In Ordinary Soil

Shuttering and shoring the earth at different levels in foundations where necessary with required prop, struts, planks, timbers, nails etc. including dewatering if necessary, complete as directed and specified (measurement to be taken in the face area timbered) Upto a Depth of 1.5 m

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. i) With earth or silt or sand obtained by head load with lead upto 90m and lift upto 2m

ii) With hill sand obtained by truck carriage loading and unloading, and carriage to the site of work.

Earth work in excavation in slushy/ marshy soil, decomposed organic matter mixed with brickbats, broken glass panes, broken earthen pots etc. removal of stumps and other deleterious matter in the proposed building site including constant water pumping for bailing out water as directed including return filling and ramming after completion of work with good quality earth (measurement will be on the basis of profile or section measurement).

Surface dressing of ground including removing vegitation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.

Cutting down trees where the building is to beconstructed of girth exceeding 300mm, grubb ing up roots, filling pits and levelling off ground lopping branches, trimming and removeing to distance beyond 30m and stacking serviceable materials and cleaning site etc. as directed. i).Girth exceeding 300mm but not exceeding 1000mm

ii).Girth exceeding 1000mm but not exceeding 1500mm

iii).Girth exceeding 1500mm but not exceeding 2000mm

iv).Girth exceeding 2000mm but not exceeding 2500mm

v).Girth exceeding 2500mm but not exceeding 3000mm

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantityetc. complete as directed and specified, including forest royality within a distance of 8.00Km. (Forest royality shall be reimbrushed on production of necessary certificate from the forest authority duly countersigned by D.F.O. concerned). ii) Other than Guwahati municipality area.

iii) Extra lead for carriage above 8.00 km per Cu.M.

iv) Loading, unloading of approved soil

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). In prop. 1:3: 6 (1 cement:3 coarse sand : 6 coarse agg. by volume (using mixture machine)

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

Providing and laying plain/reinforced cement croncrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) Using mixture machine (A) In sub - structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. M20 or Prop. 1:1.5:3

(B) Super-structure from plinth level upto 1st floor level. i) Walls (thickness not less than 100mm) including attached pillasters, buttresses, plinth and string course etc. M20 or Prop. 1:1.5:3

ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. M20 or Prop. 1:1.5:3

iii) Vertical and horizontal fins (thickness not more than 100mm) individually or forming box louvre and projected band. M20 grade concrete or prop 1:1.5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. Using 38mm thick plank

Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: i) Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face

ii) Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties for depth not exceeding 1.0M.

iii) Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like for floors etc. upto 200mm in thickness.

iv) Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). b) ISI approved super ductile TMT Bar (i) TATA/SAIL

Extra for each subsequent floor or part thereof above first floor level.

Providing welding, fitting, fixing, hoisting and fixing of roof trusses with purlin, bottom runner etc. fabricated out of a combination of two or all of the following sections: (i) square hollow sections (SHS/RHS) (ii) rectangular hollow section and (iii) M.S. black-tubes conforming to relevant I.S. code 1161-1968 as per approved design and drawing including M.S. cleat, base plate, bolts and nuts which ever required, including that required for fixing the ceiling and one coat of red oxide Zinc Chromate primer to all steel surface etc. complete as directed as per specifications. TATA MAKE

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing, fitting and fixing steel windows of standard rolled steel sections as per relevant I.S. Code, joints mitred and welded with 15mmx13mmx100mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65mm and not less than 15mm wide) bolting device, steel handles, pegs, stays of 300mm long etc. complete including providing 12mmx12mm sq. bars duly welded to steel frame at not more than 12cm c/c applying a priming coat of red-lead paint etc. complete as per drawing - Openable

Providing and fixing rolling shutters of approved make made of 80mm wide M.S. laths interlocked together through their entire lenth and jointed together at the ends by end-locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push-pull operation complete including cost of wire, spring and hood cover for the shutters.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed in sub-structure up to plinth level. In proportion 1:6.

Brick work in cement mortar with 1st class brick including racking out joints and curing complete as directed in superstructure above plinth level up to 1st floor level. In proportion 1:6.

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) In cement mortar in proportion 1:4 (1 cement:4 sand)

75 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod / Tor steel of column to be embeded in cement mortar and will be measured and paid separately) In cement mortar in proportion 1:3 (1 cement:3 sand)

10 mm thick Cement plaster in single coat for plastering on celling and soffits of stairs up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. In cement mortar 1:3

15 mm thick Cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. In cement mortar 1:4

15 mm thick Cement plaster in single coat on rough side of single or half brick wall for exterior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. In cement mortar 1:4

Extra over item for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacturer including curing complete as directed. (b). In cement mortar 1:4 (plaster) .

Extra over item for plastering on celling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed.

Extra over item for interior plastering above 1st floor level for every addl floor or part thereof including curing complete as directed. i) Single coat plaster

Extra over item for exterior plastering over wall up to a height of 1st floor level above ground level including curing complete as directed. i) Single coat plaster

Extra over item for exterior plastering over wall for every addl floor or part thereof beyond 1st floor level including curing complete as directed. i) Single coat plaster

25 mm thick cement concrete topping 1:2:4 (1cement : 2 coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish (base concrete to be measured and paid separately) to be laid in panels including curing complete as directed.

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) finished with a floating coat of neat cement finish using cement slurry for bond @ 2.75 kg. per square metre of floor area , wearing layer is to be laid in panels including curing etc. complete as directed.

65 mm thick cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75 kg. per square metre of floor area) including curing etc. complete as directed.

Providing and fixing glass strips in joints of cement concrete flooring /Terrazo flooring in all level i) 25 mm wide - 6mm thick

ii) 65 mm wide - 6mm thick

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile Choksey/Sika/Pedelite/Rouf) /white cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). EXecutive range (sizes 400mmx400mm and above) of Nitco make

Delux range (sizes 600mmx600mm and above) of Nitco make

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). Normal range (Sizes 200 mm x 200mm and above) of Somany made

Executive Range (Sizes 200mm x 300mm and above) of Somany make

Providing ANTISKID tiles of approved quality size, shape not less than 8mm on floor, skirtings over a cement mortar bed 15mm thick of 1:3(1cement: 3 coarse sand) aapproved make fixwith Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement complete at all level as specified and directed. Ceramic Tiles - Normal range (sIzes 300mm x 300mm and above)

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range (Size 600mm x 600mm) i) Asian made

Kota stone slab of 18 mm thick in riser of steps, skirting, dado and pillars laid with 10mm thick cement plaster 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete. 550mm x 550mm

Providing Bare Galvalume Sheet Roofing ( Dyna roof/Durashine TATA BLUESCOPE) at all levels including fitting and fixing self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) 0.50 mm thick

Providing Bare Galvalume Sheet roofing accessories ( Dyna roof/Durashine TATA BLUESCOPE) (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete. 0.50 mm thick

Grading roof for water proofing treatment with (a) Cement concrete 1:2:4 (i) 1 cement: 2 coarse sand: 4 graded stone agg. 20 mm nominal size)

Extra for providing and mixing normal Plastisizer Master Plast PL-1 of Choksey Chemicals @ 0.3% by weight of cement in concreting RCC structures as specified and directed by the Department complete at all levels. In concrete of proportion 1 : 2 : 4 or M-15 grade.

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet (iii) Size 125mm x 60mm (Single rebate)

Providing, fitting and fixing full panelled doors/ windows including oxidised M.S butt hinges (100mm x75 mm x3.55mm) with necessary screws (other fittings to be measured and paid separately ) With 1st class Gamari wood - 35mm thick

Providing, fitting and fixing fully glazed wooden door shutters with necessary butt hinges, screws etc. complete as per approved drawing as directed and specified at all levels.(fittings e.g. tower bolt, door handle, aldrop, glass panes etc. should be measured and paid seperately.) With Teak or Sisu Wood - 35mm thick

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. Non decorative type and block board core 35mm thick (Century /Green Ply)

Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber hollow section having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical sections shall be joined by steel screws after inserting M.S. tubular rectangular galvanised L-shaped brackets of size 100mmx100mm or plastic brackets of size 75mmx75mm with metred cut at the corners. Hinge side of the frame shall be reinforced with M.S.Tubular section of size 40mmx20mm. The frame will be fixed to the column/ stiffner/ wall with the help of 3 nos 75mm long and 4mm dia steel screws and expandable fastners on each side of the door frame complete in all respects as sepcified and directed at all levels.

Providing, fitting and fixing PVC Door shutters of Duroplast DPS 3720 make made fromm extruded PVC stiles and rails made from rigid PVC multicavity hollow chamber section of size 90mmx37mm (Toletance+ 1mm). The corners of the stiles and rails shall be metred out and fixed to each other with the help of solid plastic L-shaped brackets or M.S. rectangular tubular galvanised two nos of size 200mmx100mm and 100mmx100mm at each corner by self tapping steel screws. PVC multicavity hollow section of size 105mmx37mm shall be fixed in the middle by aluminium cleat and steel screws as lock rail. The section frame shall then be filled with PVC panels of approved colour of size 100mmx20mm. Then two numbers of bright steel rods of 6mm diameter shall be inserted horizontally through stiles and panels with two numbers of checknuts and washers all complete as specified and directed at all levels. (Door fixtures and fittings to be measured and paid seperately)

Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished ) i) Sliding Door Bolts - 250mm x 16mm

ii) Tower Bolts - 200mm x 12mm

iii) Door Handles - 100mm

iv) Hydraulic Door Closure

v) Mortice Lock vertical type - 65mm Godrej with handle (2-lever)

vi) Door Stopper with rubber stopper

Providing, fitting and fixing anodised aluminium windows and ventilators of standard sections without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC bl i)Side hung and Top hung windows and ventilators - 5mm clear glass JINDAL/HINDALCO

ii) Fixed windows and ventilators - 5mm clear glass JINDAL/HINDALCO

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubi) i) 2 Track sliding window - 5mm clear glass JINDAL/HINDALCO

ii) 3 Track sliding window - 5mm clear glass JINDAL/HINDALCO

Providing and fixing plain frosted glass of ordinary glazing quality beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for woodenbead shall be made separately) Area of glass panes exceeding 0.15m2 but not exceeding 0.52m2 - 3.50mm thick

Providing and fixing plain frosted glass of ordinary glazing quality beded in putty and fixed with/without wooden bidding including necessary cutting and glass to be required sized(payment for woodenbead shall be made separately) Area of glass panes exceeding 0.52m2 - 5.00mm thick

Providing, fitting and fixing M.S. grill of requiredpattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. i) Plain Grill - Fixed to Brickwork/P.C.C/R.C.C.

ii) Ornamental Grill - Fixed to Brickwork/P.C.C/R.C.C.

Machine driven RCC pile: Providing cast in-situ machine driven reinforced cement concrete piles of any length of required bore-diameter and with reinforcements as per specifications and drawings. Reinforcement to be measured and paid seperately. M20 grade concrete - Pile dia 400mm

Extra for using admixture (Masterplast PI-1 or equivalent) and accelerating plasticiser (conforming to IS-9103-1999 , Masterplast APCL or equivalent) for RCC concrete as specified and directed. M20 grade concrete - Pile dia 400mm

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code, for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of practice. For TMT bar (TATA TISCON/SAIL)

Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. With aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

With aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment by applying in the junction of walls, column with the floor before laying floor and after operation of item no. 26.1.3 above making a channel 30mmx30mm all over the walls and making rod holes @ 150mm apart up to ground level below and applying emulsion @ 11 litres per square meter of vertical plinth wall surface inside the building so as to soak the soil with the emulsion up to the ground level and refill the holes and channel with the original materials obtained in making channels (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. With aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Pre construction anti - termite treatment by applying the soil along the external perimeter of the building (after construction completed) to a distance close to the plinth wall as specified and as directed by the deptt. up to a depth of 300mm making rod holes along the line @ 150mm apart to a depth of 300mm and applying emulsion @ 4.5 litres per running meter ensure moistening of the soil with emulsion (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. With aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution.

Providing plinth protection 50mm thick to cement concrete 1 : 3 : 6 with coarse agg.of 20mm nominal size including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floting coat of neat cement finished.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i) 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

ii) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Applying one coat of distemper primer of approved brand and manufacture on wall surface after throughly brushing the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Distempering with dry distemper of approved brand and manufacture (twocoats) and of required shade on new wall surface to give an even shade,after throughly brushing the surface free from mortar dropings and other foreign matter and including preparing surface even and sand papered smooth.

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm)

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture ( Berger paint/ ICI paint ) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.

Applying one self-priming coat of acrylic emulsion coating of ( Berger / ICI ) brand by thinning 1ltrs of paints with 1ltrs of water over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department.

Finishing old/new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of Berger paint / Dulux (ICI) paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)

Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting with ready mixed paint , wood primer (white).

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture ( Berger paint/ ICI paint ) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. Surfaces over 100mm in width or girth for General purpose ( Berger paint/ ICI paint ).

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper with ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture( Berger paint/ ICI paint ) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. Surfaces over 100mm in width or girth for General purpose ( Berger paint/ ICI paint ).

Polishing with french sprit polishing on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust sand papered smooth and including a coat of wood filter

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F Suspended Ceiling which includes G.I. perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending G.I. intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mmx10mmx0.55mm thick fixed to soffit with G.I.cleat and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm/ 12.5mm tapered edge Gypboard (conforming to IS:2095-1982) is then screw fixed to ceiling section with 25mm long drywall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for Gypboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, window, ventilators etc, cut out made with frame of perimeter channel supported suitably to be measured and paid separately where necessary) with 12.5mm thick board GYPSTEEL MAKE

Supplying , fitting and fixing galvanised barbed wire fencing with seven strands of barbed wire 12 S. W. G .x 2plies x 4 points at 75mm apart with angle iron intermediate fencing posts not more than 1800mm apart and straining and end post etc. as necessary to be fitted with straining eye bolts and staples etc.complete as directed, specification of the angle iron post as given below. a).Intermediate post 35mm x35mm x5mm x1800mm long bottom torched and duly slotted. b). Straining post 65mmx65mmx6mmx 1820mm long with 2 stays of 35mmx35mmx1520mm long and 3 base plates 200mm x 200mm x 5mm, duly slotted to take eye bolts etc.c). c)Corner posts 65mmx 65mmx 6mm x1820mm long with 2 stays of 35mmx 35mmx 5mmx1 670 mm and 3 base plates 200mm x 200mm x 5mm,duly slotted to take eye bolts etc. d). Straining or end posts 65mmx 65mm x 6mmx 1820mm long with 1 stays of 35mm x 35mm x 5mmx 1820 mm long with base plates 200mmx 200mm x 5mm, duly slotted to take eye bolts etc. (All the angle iron posts to be embeded 600mm in C.C.pillars of size 300mmx300mmx600mm in prop.1: 3: 6 and one coat of anticorrosive ready mixed painting to all iron works) including excavation of foundation trenches for C.C. blocks and refilling and removal of surplus soil after completion of works.

Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at 200mm apart from bottom flat to middle flat including drilling, welding etc. complete. All vertical bars are to be protruded at least 100mm above the middle and top flat is to be flattended and pointed as directed. Necessary locking arrangement on both faces, arrangement for temporary closing the gate and 2 nos.( minium) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embeded in C.C brick pillars as necessary including a red oxide painting to all iron works as directed and specified. (Separate payment will be made for posts).

Providing rails for plying of rollers of gate made made from 50mm x 6mm size M.S. flat and to be fitted with 3 nos of hinged hold fasts to be embedded in concrete prop. 1:2:4 of 10mm wide and 75 mm deep over brick flat soling 250mm wide including curing etc. complete.

Providing roller to the gate including welding etc.complete a) With 25mmx50mm (dia) roller

Supplying fitting and fixing M.S. cattle trap fabricated, welde, mitred and jointed as per relevant IS code with ISMB 250 joist spaced not more than 1800mm apart and ISA 65 x 65 x 6 spaced not more than 200mm apart and fixing the same over RCC member / Brick wall complete as specified and directed.

Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines,grades and cross sections.

Granular Sub-base with Close Graded Material (Table:- 400-1) - By Mix in Place Method (Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density,complete as per cl. 401( with an initial lead of 5 Km.)( Including cost of testing of materials at site and laboratory as directed by the deptt.) i) for grading- I Material

ii) for grading- II Material

ii) for grading-III Material

For Base course - 'Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fillup the interstices of coarse aggregate,watering and compacting to the reqd. density ( with an initial lead of 5.0 km.) - by Manual means i) Grading I - Using Screening Crushable type such as Moorum or Gravel

ii) Grading II - Using Screening Crushable type such as Moorum or Gravel

iii) Grading III - Using Screening Crushable type such as Moorum or Gravel

Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of specified quantity using mechanical means.)( Including cost of testing of materials at site and laboratory as directed by the deptt.) A. 'Primer @ 0.60Kg per sqm ii) 'With bitumen emulsion-CSS-1 ( IS-8887-2004 )

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.( Including cost of testing of materials at site and laboratory as directed by the deptt.) III) 'With Bitumen emulsion CRS-1 b) Dry & hungry bituminous surface

Open - Graded Premix Surfacing (Providing, laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen to required line, grade and level to serve as wearingcoarse on a previously prepared base, including mixing in a suitable plant laying and rolling with a smooth wheeled roller 8-10 T capacity to yhe reqd. level and grade. ( including carriage up to initial lead of 5.0 km from quarry and carriage of mixed materials up to 10.0 Km initial lead from mixing plant )( Including cost of testing of materials at site and laboratory as directed by the deptt.) A. ' Without anti stripping agent iv) 'Open-Graded Premix Surfacing using cationic Bitumen Emulsion CMS

Seal Coat (Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats) ( including carriage up to initial lead of 5.0 km from quarry )( Including cost of testing of materials at site and laboratory as directed by the deptt.) a) 'Without anti stripping agent ' Type B (Providing and laying of premix seal coat with HMP of appropriate capacity not less than 75 tonnes/ hours using crushed stone chipping 6.7 mm size and penetration bitumen of 60/70 or VG-30 grade.)( including carriage up to initial lead of 5.0 km from quarry )

Supplying, fitting and fixing I.S.I marked or similar approved H.C.I pipe including bolts and nuts and other fittings as required and complete at all levels including below G.L as directed and specified. In exposed surfaces or in trenches - 150mm dia

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Supplying and placing ferrocement septic tanks of rectangular shape in to pit with manhole cover with cleaning arrangement over single brick flat soling and 75mm 1:3:6 P.C.C. Baffle wall, inlet and outlet etc are provided at suitable points complete as directed. i) 10 Users

ii) 50 Users

iii) 100 Users

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 58 Kg. weight complete as directed and specified

Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 19 Kg. weight complete as directed and specified

Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. Bore hole of 100mm diameter

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. PVC Pipe - Supreme Brand - 110mm dia

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed. PVC Pipe - Supreme Brand - 75mm dia

Supplying fitting and fixing ribbed screen PVC filter 3.00 metre long and 80mm dia

Supplying fitting and fixing check valve (non return valve) including thread to pipes - 80mm dia

Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained

Flushing, clearing, washing and watering of the tube well

Providing fitting and fixing white vitreous china pedestal type water closet (European type W.C pan 400mm high ) of Parryware/JACQUAR make with seat and lead ,CP brass hinges and rubber buffers ,10 litre low level PVC flushing cistern with fittings, CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required - White

Providing fitting and fixing white vitreous water closet squatting pan ( Indian type Orissa pattern) of size 580x240mm 'S' trap, 10 litre low level PVC flushing cistern with manually controlled device(handle lever) of Parryware/JACQUAR make with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.. - White

Providing fitting and fixing white vitreous china flat back type lipped front urinal basin of (455x360x267)mm of Parryware/JACQUAR make with automatic flushing cistern of similar colour and standard flush pipe and CP brass spreader with brass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. i) White - For range of 2 No. urinal basin with 5ltr. Flushing cistern

ii) White - For range of 3 No. urinal basin with 10ltr. Flushing cistern

Providing vitreous China wash basin of size 630mm x450mm of Parryware make with CI/MS brackets, 32mm CP brass waste coupling of standard pattern,C.P stop cock,C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. White vitreous china wash basin of size 630mm x450mm

Providing fitting & fixing white vitreous china kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings, cutting & making good the walls wherever required. Kitchen sink of size (610x450x200) mm

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing fitting and fixing glass shelf with C.P. guard rail of Agmeco make to wall complete fixed with 25mm long screw, rawl plug etc.complete - 600mm x 125mm.

Providing, fitting and fixing soap dish of Agmeco make complete as specified and directed - Stainless Steel Soap Dish Rectangular (Cat no. MS 0273)

Providing, fitting and fixing Chrome plated (CP) towel rail of Agmeco make complete as specified and directed - 450mm long

Providing fitting and fixing robe hook of Agmeco make complete as directed and specified - Chrome Plated

Providing and fixing S.F.M.C. Brand 3 layer (Outer green coloured UV Stabilised, middle black coloured UV Stabilised and inermost layer white coloured with antimicrobial property) Fusion welded PP-R (Poly propylene- random copolymer) Pipes, SDR 7.4 having thermal stability for hot and cold water supply including all plain PP-R fittings and brass threaded PP-R fitting and clamping, cutting and making good to the damages. (A) Exposed or in trenches i) PN-16 Pipe,25 mm OD,SDR-7.4

ii) PN-16 Pipe,40 mm OD,SDR-7.4

(B) Concealed pipe with cutting chases & making good the walls i) PN-16 Pipe,16mm OD,SDR-7.4

ii) PN-16 Pipe,20 mm OD,SDR-7.4

Providing fitting and fixing robe hook of Agmeco make complete as directed and specified - Chrome Plated

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. i) In exposed surfaces or in trenches - 110mm dia

ii) In exposed surfaces or in trenches - 75mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L. as directed and specified. i) In exposed surfaces or in trenches - 110mm dia

ii) In exposed surfaces or in trenches - 75mm dia

Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. i) In exposed surfaces or in trenches - 110mm dia

ii) In exposed surfaces or in trenches - 75mm dia

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. i) In exposed surfaces or in trenches - 110mm dia

ii) In exposed surfaces or in trenches - 75mm dia

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. i) In exposed surfaces or in trenches - 110mm dia

ii) In exposed surfaces or in trenches - 75mm dia

Supplying fiting and fixing PVC cross ‘T’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. i) In exposed surfaces or in trenches - 110mm x 110mm

ii) In exposed surfaces or in trenches - 75mm x 75mm

Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. i) In exposed surfaces or in trenches - 110mm dia

ii) In exposed surfaces or in trenches - 75mm dia

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. i) 100 dia

ii) 75 dia

Providing fiting & fixing C.P.Grating to the floors complete as directed and specified 100mm dia i) 100mm dia

ii) 75mm dia

Supplyinf Fitting and fixing Ajoy Flowguard CPVC ( Chlorinated Polyvinayal Chloride ) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting including clams at 1.0 m spacing. This include jointing of pipes & fitting with one step CPVC solvent cement and testing of joints complete at all level as directed and specified. (A) Exposed or in trenches i) 25 mm nominal outer dia pipes

ii) 40 mm nominal outer dia pipes

(B) Concealed pipe with cutting chases & making good the walls i)15 mm nominal outer dia pipes

ii)20 mm nominal outer dia pipes

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) Jaguar make - Continental

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. Jaguar make - Continental, Pillar cock (ISI) / Pillar cock

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) Jaquor Continental - 15mm dia Male / Female (long thread)

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. i) 40 mm dia.

ii) 25 mm dia.

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) Jaquar brand - Continental - Sink cock with swinging casted spout

Supplying and fitting ball valve as specified and directed.. i) 25 mm dia. (gun metal)

ii) 20mm dia. (gun metal)

Supplying fitting and fixing gun metal check valve including necessary threads to pipes. 40 mm dia (Heavy type)

Supplying fitting and fixing Chrome Plated (C.P.) shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid separately) Jaquar make - Continental - Shower arm 190mm long heavy casted body with wall flange

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes i) 2000 Lt capacity - Sintex make

ii) 1000 Lt capacity - Sintex make

Any other unseen item of work which are not included in the estimate / BOQ , but may be required during execution of the works are as per APWD SOR for 2010-11 for Civil and Sanitary & Water Supply and Electrical works ( Rate to be quoted on lumpsum basis on Rs. 1,50,316.00)

Wiring to a light point with 1.5 sq. mm PVC. insulated unsheathed 1.1KV. grade I.S.I. marked as approved by this department single core copper conductor cable in Recessed PVC. conduit wiring system with 19 mm. dia, 2.0 mm thick rigid P. V.C. conduit including 6 Amps flush type switch in iron clad switch board (I.S.I. marked)with phenolic laminated sheet cover ceiling rose complete. i) SP upto 3.00 metre length.

ii) MP upto 6.00 metre length.

iii) LP upto 10.00 metre length.

Wiring as in item no. 57 above in Recessed PVC. Conduit wiring system with 19 mm. , 2.0 mm thick rigid P.V.C. Conduit to a Fan/exhaust Fan point including 6 Amps flush type (I.S.I. marked) switch, ceiling rose I.C. switch board with phenolic laminated sheet cover as required complete. i) MP upto 6.00 metre length.

ii) LP upto 10.00 metre length.

Wiring to 5 pin 6 Amps plug with 1.5 sq. mm PVC. insulated unsheathed single 1.1 K.V. grade ISI marked (as approved by this department) single core copper conductor cable in Recessed P.VC. conduit wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch, I.C. switch board (I.S.I. marked) with phenolic laminated sheet cover including earth continuity with 2.5 sq. mm. PVC. insulated unsheathed single core copper conductor cable to third pin of the plug socket etc. as required complete with 19 mm. dia. rigid PVC. conduit pipes when placed elsewhere.LP upto 10.00 metre length.

Wiring as in item no. 115 when fixed on the same board In Recessed PVC. conduit wiring system on the recessed I.C. switch board.

Wiring for 5 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated unsheathed I.S.I. marked single core copper Conductor cable in Recessed P.V.C. conduit wiring system including providing and fixing 5 pin 16 Amps flush type socket outlets and 16 Amps flush type switch, I.C. switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm PVC. insulated unsheathed single core copper conductor cable to the 3rd pin as required complete with 19 mm. dia. rigid P.V.C. Conduit pipes. Extra long point upto 15.00 metre length.

Supplying fitting and fixing Industrial plug and socket in surface mounting TPN sheet steel powder painted MCBDB incorporated with MCB, DIN rail. Neutral link, earth bar with following rating of TPN MCB complete with making necessary connection etc. as specified and directed by the department. 30A capacity TPN Industrial plug and socket wth metal box and 1 no. TPN MCB.

Wiring for drawing sub-main line with P.V.C. insulated unsheathed 1.1 K.V. grade (ISI marked or as approved by this department) single core copper conductor cable in with earth continuity in Recessed PVC conduit wiring system i) With 2 x 2.5 sq. mm. + earth continuity with 1x2.5 sq. mm. PVC.insulated unsheathed single core copper conductor cable in 19 mm. Dia, 2.00 mm thick Rigid P.V.C. Conduit pipes.

ii) With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. PVC. insulated unsheathed single core copper conductor cable in 19 mm. Dia, 2.00mm thick Rigid P.V.C. Conduit pipes.

iii) With 2 x 6 sq. mm. + earth continuity with 1x4 sq. mm. PVC. insulated unsheathed single core copper conductor cable in 19 mm. Dia, 2.00 mm thick Rigid P.V.C. Conduit pipes.

Wiring for drawing sub-main line in Recessed P.V.C. Conduit wiring system. i) With 3 x 6 sq. mm. + 1 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. PVC. insulated unsheathed single core copper conductor cable in 25 mm. dia.2.00mm thick rigid P.V.C. Conduit pipes.

With 3 x 10 sq. mm, + 1 x 6 sq. mm. + earth continuity with 1x4 sq. mm. PVC. insulated unsheathed single core copper conductor cable in 32 mm. dia.2.00mm thick rigid P.V.C. Conduit pipes.

Supplying and fixing L type cast Aluminium anodized wall bracket 150mm(Nominal size) perojection length with 3mm. Thick, 75mm dia. back plate and brass bracket holder including connections etc complete(without shade and bulb)

Supplying installation, testing and commissioning of the following T5 luminaire complete with all accessories such as ballast, starter etc. in the ceiling including supplying nut, Y type suspension arrangement as specified with MS rod of 4mm dia. including connections with 1.5sqmm PVC insulated S.C copper conductor. TPH824/228 D8 DI HF 2xTL5 28W.

Supplying, installation, testing and commissioning of the folowing LED luminaire complete with all accessories such as driver etc.directly on wall/ceiling including connection with 1.5 sqmm PVC insulated S.C copper conductor as required and as directed by the department. LED lamp indoor application, operating voltage 90V-250V, 12V DCII, Model GN11J-3 , LED lamp with mails input with 12V, 5Ah sealed maintanance free battery(Make: Philips, Bajaj etc).

Supplying, installation, testing and commissioning of the folowing LED luminaire complete with all accessories such as driver etc.directly on wall/ceiling including connection with 1.5 sqmm PVC insulated S.C copper conductor as required and as directed by the department. BBS170 1xDLED -5000 PSU WH

Supplying installation, testing and commissioning of the following TL5fluorescent luminaire complete with all accessories such as ballast, starter etc. directly on wall/ceiling including connections with 1.5sqmm PVC insulated S.C copper conductor as required and as directed by the department. b)ADRENO 28W TWG207 1xTL528 HF.

Installation of Earth station with 40 mm. dia. and 4.50 metre long G.I. pipe with necessary G.I. reducing socket 40 mm x 20 mm. size locking arrangement with h'inged cover plate, funnel, G.I. nuts, through bolts etc. for putting pipe and re-fitting with necessary enclosure on the top etc. as required complete.

Extra for using salt (5 kg) and Charcoal (64 kg. for pipe earth electrode as required.

Supplying and laying 6 S.W.G. Copper wire at 0.50 metre below ground level for Conductor earth electrodes including soldering, excavation work and refilling etc. as required complete.

Providing and fixing of lighting conductor finial made of 25mm dia. 300mm long copper tube having single prong at top with 85mm dia. 3mm thick coper base plate including making hole and fitted with 6mm dia. rag bolts and nuts.

Supplying including fitting fixing of Electronic STEP type regulator for ceiling fan complete with all connection in the existing board as required complete and as directed by the department.

Supplying incl. fitting fixing of 5 star rating AC ceiling fan complete with down rod, canopy etc. of following sweeps with making necessary connection etc. as required complete and directed by the department(without regulator) 1400 mm sweep

Supplying including fitting fixing of A.C. Exhaust fan in the existing hole on the wall of follwing sweeps and making necessary connections etc. as required complete and as directed by the Department. Domestic - 300/305 mm sweep

Supplying with fitting and fixing sheet steel, phosphatised, powder painted double door surface mounting vertical TPN MCB DB (IP-43 protection) incorporated with bas-bar, neutral iink, earth bar and Din rail etc. fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as specified and directed by the department. 6 way TPN (8+18) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Double door surface mounting SPN MCB DB incorporated. with bas-bar, neutral link, earth bar and Din rail etc. fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as specified and directed by the department. 12 way SPN Double door

Supplying with fitting and fixing 100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as specified and directed by the deptt. [Legrand/Merlin Gerin/ Hagger make] - 40A

Supplying with fitting and fixing 300mA sensitivity 240/415V 50Hz Triple Pole RCCB of the following capacity complete with making necessary connection as specified and directed by the deptt. [Legrand/Merlin Gerin/ Hagger make] - 63A

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as specified and directed by the deptt. [Legrand/Merlin Gerin/ Hagger make] - DP 10 KA 240 //415 50 Hz MCB (C Series) - 40A

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as specified and directed by the deptt. [Legrand/Merlin Gerin/ Hagger make] B Series - Single Pole 10 KA 240 //415 50 Hz MCB i) 6A

Supply.and laying of following size PVCIXLPE insulated and PVC sheathed 11 KV gd aluminium conductor LT armoured U.G. cable laid in pucca flooring road crossing, drain crossing and partially in air through G.!. Pipe (TatalNezone make) with necy bend and socket including excavation and refilling the treance and making good damange done as specified and directed by the deptt. 25.00 mm2 3&1/2core U.G. Cable in 40mm dia medium quality G.I. Pipe

Supplying with installation testing and commissioning of hi-wall non ductable split type 3* model air conditioner of the following capacity with corded remote complete with copper pipe and electrical connection between the room unit as directed by the department. 2.00T cap. (Carrier Aircon make)

Supplying and installation of automatic 5KVA wall mounting voltage stabilizer of input voltage 140-280 volt and output voltage of 220-230 volt +1% frequency 47-53Hz including high and low voltage cut off as directed and specified by the department.

Supplying fitting and fixing single phase automatic DOL starter of following specification Overload Relay Range 6.0 - 9.3 Amps for 3.7 KW

Supplying with fitting and fixing TP 10KA 415V 50Hz MCB of the following capacity complete with makingt necessary connections as specified and directed by the department(Legrand/Merlin Gerin/Hagger make) 1.TP 10 KA 240 //415 50 Hz MCB i) 40A capacity.

ii) 63A capacity

Supply and laying of following size PVC/XLPE.insulated and PVC sheathed 11 KV gd aluminium conductor LT armoured UG. cable laid in ground/partially in air (10.0% of cable length) including excavation af cable trench upto depth of 75cm, refilling, protective brick covering, sand cushioning etc. complete handling of surplus spoil, debries etc. to proper place as specified and directed by the deptt. 150sqmm 3x1/2 core UG cable.

Supply.and laying of following size PVCIXLPE insulated and PVC sheathed 11 KV gd aluminium conductor LT armoured U.G. cable laid in pucca flooring road crossing, drain crossing and partially in air through G.!. Pipe (TatalNezone make) with necy bend and socket including excavation and refilling the treance and making good damange done as specified and directed by the deptt. 150.00 mm2 3&1/2core U.G. Cable in 80mm dia medium quality G.I. Pipe

Supplying including installation of submersible type water supply motor pumpset with all accessories including panel board on C.C. foundation of Proportion 1 :2:4 jammed with M.S. Nuts and Bolts wire rope submersible cable without suction G.!. Pipe including making necessary connection etc. as reqd. complete 3 HP Three Phase.

Supplying including fitting and fixing of the following luminaires complete with all acessories and making necessary connection with 1.5 sq.mm. P.V.C. insulated S.C. copper conductor as required and as directed by the department. ii) Post top lantern complete with all accessories,and elliptical/conical cover with 1x70 w HPSV lamp SPC101/ 102/ 104/70(E)HPF(Philips make)

Supply and laying of following size PVCIXLPE insulated and PVC sheathed 11 KV gd aluminium conductor LT armoured U.G. cable laid in ground/partially in air (1 0% of cable length) including excavation of cable trench upto depth of 75cm, refilling, protective brick covering. sand cushioning etc. complete handling of surplus spoil, debries etc. to proper place as specifiea and directed by the deptt. 4.00 mm2 2core U.G. Cable

Wiring for drawing telephone point in recessed PVC conduit wiring system with 0.71 mm size insulated and sheathed copper HFFR conductor of telephone cable conforming to ITI and ITD specifications as required complete: i) 3 pair with 19 mm dia, 2.0 mm thick rigid PVC pipe

ii) 5 pair with 19 mm dia, 2.0 mm thick rigid PVC pipe

Supplying including fitting and fixing telephone jack complete as per direction of department.

hitech construction