Special repair of Sub Health Centre at Village Kondal in Palwal Distt. Re-Tender

Amount

Civil & P.H. Works

Scraping cement plaster (HSR 8.32 c)

Dismantling brick work tile masonry or tile lining and tile terracing in cement. (HSR 8.5 b)

Cement concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth (HSR 10.39)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR -10.41).

Terracing consisting of tiles 22.86 x 11.43 x 3.81cm. laid over 87.50 mm. mud filling on a layer of 25 mm. mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg. per Sqm. on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

First class brick work laid in cement sand mortar 1:4 in foundation and plinth. (HSR 11.4)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 Meter above plinth level ( HSR 11.7)

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.89).Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thickcement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Not : Tile shall be of premium quality (first quality) of reputed manufacturer like:- NITCO, KAJARIA, RAK, SOMANI, JHONSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.91). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. [HSR 14.92(b)].Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. First Storey

Plastering on wall 12 mm thick cement plaster 1:4 (HSR 15.5)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

Providing and Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.2).

Painting two coats excluding priming coat with ready mixed paint in all shades on new wood work. (HSR 16.4)

Providing and Applying priming coat with metal primer on new steel or iron work including preparation of surface. Painting on mettalic Surfaces etc. (Note:- First quality paint/primer of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.9).

Providing and Applying Painting two coats excluding priming coat with ready mixed paint for matelic sufraces in all shades on new steel or iron work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.17).

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.58)

Providing and Applying Providing two coats of exterior acrylic emulsion paint. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). [HSR 16.79 (b)

Supplying and fixing hydraulic door closer I.S.I mark, with necessary screws etc. complete (b) I.S.I designation no. II (size of door 701 mm to 850 mm) [HSR 17.82(b)].

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 30 mm thick. [HSR 17.92 (i) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (c) decorative veneering with vertical grain cross bands and face veneer on both sides teak facing and edges lipped with commercial hard wood with laminated core:- Duro, Green Only. [HSR 17.93 - Note 1 under 17.18]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material (iii) (HSR 17.93a iii

Wrought iron and mild steel (using angles, flats, square bars, tees and channels), ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Pressed steel sheet frames (chowkats) consisting of 2 mm thick steel sheet of the specified section including iron lugs (hold fasts) iron hinges, conforming to P.W.D specifications, including bolts for fixing stops, lock notch, provision for receiving tower bolts, and finished, with one coat of ready mixed paint red lead non-setting primer of approved quality fixed in position including the cost of cement concrete 1:3:6 for filling in the frames and cement concrete 1:3:6 for lungs complete. b) Door and window frame of size 76 mm x 38 mm with 35 mm wide single rebate (HSR 18.34 b)

Door and window frame of size 114 mm x 50 mm. with 35 mm. wide double rebate. (HSR 18.34 d)

Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described. (b) Size 630 mm (ii) Single Colour. (Make Hindware) (HSR 30.2 b ii)

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (b) Double trap syphonic (ii) Single Color. [HSR 30.5 (b) (ii)].

Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (HSR 30.12) (i) white

Providing and fixing in position best Indian make flat back or angular lipped front urinal 465 mm high consisting of :-(HSR 30.19i) Flat back lipped or angular urinal basin of vitreous china ware (to the approval of Engineer-in-charge)5 liters capacity mosquito proof Indian make C.I automatic flushing cistern, painted with non-yellow white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15mm pipe.Pair of R.S or C.I painted brackets and brass couplings Standred size G.I flush pipe with C.P brass wall clips and unions complete including cutting and making good the walls and floor and painting o fittings etc (as required by the Engineer-in-charge)i)White

Providing and fixing in position glass shelf fixed in with rawl plugs with C.P. Brass screws, complete including cutting and making good the walls etc. (a) with C.P. Brass brackets and guard rail. (i) 600mm x 125 mm . [HSR 30.69 (a) (i)].

Providing and fixing 25mm thnick marble partitions for different type of urinals (HSR 30.40) (B) (II) (i) vetreous Chinaware Partition plate

Providing and fixing in position best quality stainless steel sinks with complete fittings a fully described in item No. 30.51 above (HSR 30.53) (a) Size 600mmx450mmx200mm

Providing and fixing in position best India make towel rails fixed in with rawlslugs embedded in walls with CP Brass screws, Complete in all respect including cutting and making goods the walls etc. (HSR 30.68) (d) CP Brass Two swivel towel rail 400mm longh

Providing and fixing in position best Indian make Soap dis fixed into wall with C.P. brass screws and complete in all respects including cutting and and making goods the walls etc (HSR 30.70) (d) Vitreous Chinaware recessed soap dis with hand rails (iii) Mixed Colour

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc (HSR 30.71 a) (i)

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (a) Bib cock long body (HSR 30.75)

(b) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) a) 15mm stop cock(HSR 30.76) i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make lavatory suites (with full anti splash rim in vitreous chinaware and all other necessary fittings as fully decribed in item no 30.41 above (HSR 30.42) R.S or C.I brackets for building into wall including painting 32 mm C.P brass waste with C.P brass chain and rubber plug15 mm C.P brass screw down pillar tap with jamnuts or couplings best design (as approved by the Engineer-in-charge) All fittings best Indian make and; to the approval of the Engineer-in-chargeAll brass work chromium plated and complete in all respects including cutting and making good the walls floors and painting of fitting etc.Size 530mmx430mm with one no. tap

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. 1500 Ltr. Cap. (HSR 30.119)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc internal work Exposed on wall (DSR 18.10). (ii) 20 mm internal diameter of pipeline

(iii) 25 mm internal diameter of pipeline

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end) (DSR 18.17) (a) 20 mm internal diameter

(b) 25 mm internal diameter

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) (DSR. 18.46) (b) 20 mm internal diameter

(c) 25 mm internal diameter

Shiv Kumar, Contractor