INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE B , TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE BLOCK , NEW

GRAND TOTAL 21651286.31

Providing and laying Screed of cement Mortar ratio 1:1 of sufficient minimum thickness

not exceeding 10 mm, to give a smooth& even surface and curing etc. complete as per

2.2 MR engineer incharge instructions. Cost should be inclusive of hacking the existing floor so SQM 675.00 409.46 276387.28

IPS adhere to the existing floor.(Wooden & Carpet Flooring)

Half brick masonry

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in superstructure above plinth level up to floor V

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) SQM 179.09 932.10 166925.13

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every SQM 179.09 80.10 14344.71 -

third course of half brick masonry.

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level in cum 4 7,809 31,237

all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

Plaster on brickwall

15 mm cement plaster on the rough side of single or half brick wall of mix. SQM 175 307.90 53882.50

1:4 (1 cement : 4 fine sand)

2.7 13.4 12 mm cement plaster of mix

Providing and laying in position cement concrete of specified grade excluding

2.8 4.1 the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm CuM 112 5,789.60 648435.20

Providing and laying water proofing treatment to vertical and horizontal surfaces Sqm 45.00 705.70 31756.50

of depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing

compound conforming to IS 2645 in recommended proportions including

rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm

cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing

2.9 22.3 compound in recommendedproportion including rounding off junction of vertical

and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen

applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC

sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to

each other with bitumen @ 1.7 kg/ sqm).

3 FLOORING & DADO WORKS

Providing and laying machine cut, mirror polished, Italian Marble stone

flooring laid in required pattern in linear portion of the building all complete as

per architectural drawings, with 18 mm thick stone slab laid over 20

mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including

3.1 11.51 pointing with white cement slurry admixed with pigment to match the

marble shade including rubbing, curing and polishing etc. all complete

as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, SQM 380 5986.20 2275354.62

Fire Red or Dark Emperadore etc.

3.2 11.41.4 Vitrified tiles

Providing and laying vitrified floor tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS: 15622, of approved make, in all colours and shades, laid on

20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey

cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

matching pigments etc., complete.

Providing and laying Ceramic glazed floor tiles of size 300 x 300 mm(thickness SQM 45 996.70 44851.50

ro be specified by the manufacturer ), of 1st quality conforming to IS:15622 , of

approved make, in all colors and shades except White , Ivory , Grey, Fume red

brown laid on 20mm thk. bed of cement mortar 1:4 ( 1 cement : 4 coarse sand ) ,

including pointing the joints with white cement and matching pigments etc.

Anti skid vitrified tiles

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300

mm or more (thickness to be specified by the manufacturer), of 1st

quality conforming to IS : 15622, of approved make, in colours White,

3.4 11.39 Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4

(1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/

sqm including grouting the joints with white cement and matching

pigments etc., complete.

Ceramic glazed wall tiles

Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 Sqm 110.00 1030.30 113,333.00

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by

Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed

of cement mortar 1:3 (1 cement : 3

coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 12 mm thick hexagon shaped ceramic, Mosaic in design Sqm. 60 4,396.68 263800.83

3.6 MR ,colourand shape as per selection designer tiles as per engineer incharge

selection for wall cladding and floor

Engineered wood

Providing and Laying 15mm thick Engineered Wood with plank width of

185mm/135mm and Length of 1800mm / 2100mm/2400mm and top layer

of 3mm oak/walnut natural veneer. Surface of top layer is pre finished

with several layers of UV hardened acrylic lacquer, free from

3.7 MR formaldehyde and solvents. Flooring planks shall be interlocked using

patented Plank Lock system in a glue- less, floating manner .

Engineered Wood planks shall be a composition of 3 layers of board with

directions of each layer oriented at right angle to the adjacent layer of

natural stain in lacquer and non- beveled/bevelled, in length and width as

specified by the manufacturer.

Carpet flooring

Providing & Fixing t of PVC and Glass nonwoven backed, solution dyed nylon SQM 110.00 3,871.17 425829.25

tiled carpet flooring with Piel height of 4.0mm and low loop pile length of 2.0mm,

3.8 MR having overall thickness of 7 mm. Carpet tile should also have antistatic

properties of 1.0 KV or Less ( JISL 4406, at 23 degree C, 25 % RH).

Laminated wooden flooring

Providing and fixing laminated 12 mm thick AC-4 laminated wooden flooring as sqm 40.00 1,968 78735.76

per the sample approved by engineer in charge.

Artificial grass

Providing & Laying Artificial grass made of polyethylene(PE) +

polypropylene(PP) ,Bi color with a density of 18900/Sq.Mt. with pile height 35mm

3.10 MR , laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) Sq.Mt. 35.00 656 22964.60

Granite stone flooring

Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as

per the architectural drawings with 18 mm thick stone slab over 20 mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

3.11 11.56 jointed with cement slurry and pointing with white cement slurry admixed with

pigment of matching shade including rubbing , curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown,Cat Eye or 25.00 3526.60 88,165.00

Raised/false access flooring

Providing and fixing removable raised/false access flooring with system

and its components of approved make for different plenum height with

possible height adjustment upto 50 mm, comprising of modular load

bearing floor panels supported on G.I. rectangular stinger frame work

and G.I. Pedestal etc. all complete, as per the architectural drawings,

as specified and as directed by Engineer-in-charge consisting of:

(a) Providing at required spacing to form modular framework, pedestals

made out of GI tube of thickness minimum 2 mm and 25 mm outer

diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm

x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer

diameter with two GI Check nuts screwed on the stud for level adjustment

upto 50mm, locking and stabilizing the pedestal head in position at the

required level. The pedestals shall be fixed to the subfloor (base) through

3.12 base plate using epoxy based adhesive of approved make or the machine

screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of

rectangular size 570x20x30x0.80mm thick having holes at both ends

for securing the stringers on to the pedestal head using fully threaded

screws ensuring maximum lateral stability in all directions, the grid

formed by the pedestal and stringer assembly shall receive the floor

panel, this system shall provide adequate solid, rigid support for access

floor panel, the system shall provide a minimum clear uninterrupted

clearance between the bottom of the floor for electrical conduits and wiring etc.

all complete as per the architectural drawings, as specified

and as directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium

grade Filled Steel anti static high pressure Lamination of 800H grade

(FS800H). Access Floor panel shall be steel welded construction with

11.54.1 300 mm Finished Floor Height (FFH) Sq.Mt. 20.00 5075.3 101,506.00

4 PARTITIONS Frame works

The Gypliner wall lining : 45mm Gypliner channel section (0.40mm thick having SqM 350.00 390.00

two flanges of 18mm each) placed at 610mm centre to centre in 25x25mm wall

angle(0.40mm thick having two flanges of 25mm each) is fixed to floor and

with nylon sleeves and steel screws at 610mm centres. Fixing bracket (0.90mm

29.5mmwide, 195mm long) is fixed to the wall with the help[ of nylon sleeves

steel screws at 900mm centres to hold the Gypliner section in position and level.

Work to be done as per the satisfaction of Engineer in Charge

Metal stud partition

100 mm Metal stud partition , 100mm thick Gypserra™ stud partition SqM 480.00 503.68

fixed to C-stud. 48x0.5mm Gypserra™ C-stud {Material-IS 513, Y/S-300Mpa,

Finish - AZ150 (IS 15961)} placed at 610mm c/c in 50x0.5mm Gypserra™

{Material-IS 513,Y/S-300Mpa, Finish - AZ150 (IS 15961)} floor and ceiling

channel. Floor & Ceiling channel is anchored to the floor & True ceiling using

Gyproc® Rawl plug Ø8x45mm {MaterialIS 513 CR1 grade, Zinc coating, Pull

Out Load-6.8kN for M30 concrete grade} /Hilti X-GN20MX anchor fasteners at

600mm c/c in centerline. Floor channel to be wrapped with 70µ Self Adhesive

LDPE moisture barrier film to further improve corrosion resistance performance.

12.5mm thick Gypboard® Plain board strip of 50 mm width is placed between

ceiling channel and RCC

ceiling slab to improve fire performance of the system. A Gypserra™ noggin

channel {Material-IS 513,Y/S-300 Mpa, Finish - AZ150 (IS 15961)} of 48x0.5mm

width has to be provided at the horizontal joints of the two boards. First layer of

Gyproc® boards to be screw fixed with Gyproc® drywall screws of 25mm at

minimum spacing of 600mm at centre and 600mm at periphery. Second layer to

be screw fixed Gyproc® drywall screws of 35mm at minimum spacing of

300mm at centre and 300mm at periphery.

The junction of the partition with masonry & all penetration through the partition

has to be treated with Hilti/Pyroplex fire and acoustic sealant.

.All complete as per the drawing & directions of engineer-in-charge.

GYPSUM BOARD FOR PARTITION

Providing and fixing one layer of 12.5mm thick Standard Gypsum

plasterboards (Confirming to IS 2095: Part 1) is screw fixed vertically to

either side of Ultraframe wall Studs with 25mm long Drywall Screws at

300mm centers. The screw fixing of Gypsum plasterboards to the metal

framing at the periphery, openings and cut edges should be at 150mm

4.3 MR centers. The horizontal & vertical joints of the Gypsum plasterboards on SQM 1020.00 197.16 201099.62

both sides of the metal framework must be staggered so as to avoid

through and through joints. All joints to be taped & finished and 1mm

putty with 50mm wide Paper tape & All Purpose Joint compound.

(Confirming to ASTM C475)

FIRE RESISTANT GYPSUM BOARD

Providing and fixing partition upto ceiling height consisting of G.I. frame

andboards, fixed to the studs using metal to metal flat head screws,

jointing and finishing to a flush finish with recommended jointing

jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint

finisher and two coats of primer suitable for board as per manufacture's

specification and direction of engineer in charge all complete.

required board, including providing and fixing of frame work made of

section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/

sqm(both side inclusive), consisting of floor and ceiling channel 50mm

4.4 9.105 wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor

and ceiling at the spacing of 610 mm centre to centre with dash fastener

12.5 mm dia meter 50 mm length or suitable anchor fastener or metal

screws with nylon plugs and the studs 48 mm wide having one flange of

mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm

centre to centre by 6 mm dia bolts and nuts, including fixing of studs

both ends of partition fixed flush to wall with suitable anchor fastener or

metal screws with nylon plugs at spacing of 450 mm centre to centre, and

fixing of boards to both side of frame work by 25 mm long dry wall screws

on studs, floor and ceiling channels at the spacing of 300 mm centre to

75 mm overall thickness partition with 12.5 mm thick double

skin fire rated Glass Reinforced Gypsum (GRG) plaster

board conforming to IS: 2095: (part 3) : 1996 (Board with

BIS certification marks)

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails,

including a coat of approved primer on one face, and fixed on wooden

/steel frame work, complete as per direction of Engineer-incharge (Frame

work shall be paid for separately).

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type

Aluminum framed glazed partition

Supply & Installation of Full Height Wideline Partitions systems of size 100 x 25

mm thick section for the partitions using verticals at the solid partition junction &

Horizontals at top & bottom with snap on option for installating glass & 'T'

Section, corner Section & Vertical "I" Section between Glass to glass from FFL

upto 2600mm Complete in all respect considering 10 mm thk toughened glass

with double sided adhesive tapes for glass to glass butt joints all complete as

per drawings and as directed by Engineer-in-charge

Providing and fixing thermal insulation with Resin Bonded Fibre glass Sqm 405.00 316.6 128223.00

wool conforming to IS: 8183 having density 24 kg/m3, 50 mm thick,

4.7 12.57 wrapped in 200G Virgin Polythene Bags fixed to wall with screw,

rawel plug & washers and held in position by criss crossing GI wire

etc. complete as per directions of Engineer-in-Charge.

5 Wall Finishes

Providing and applying white cement based putty of average thickness

5.1 13.80 1 mm, of approved brand and manufacturer, over the plastered wall SQM 640.00 115 73,696

surface to prepare the surface even and smooth complete.

5.2 MR Providing and fixing MDF Skinning

using 12mm thick exterior grade MDF on one side on existing framing. Sqm. 310 391.36 121322.48

b using 8 mm thick exterior grade MDF on one side on existing framing. Sqm. 250 238.33 59582.28

Providing and fixing 18mm thk decorative wall profiled mdf planks with Sqm. 206 5,821.15 1199157.61

decorative film over wall and ceiling as cladding. Sample to be submitted from

all the approved make or equivalent for approval of engineer in charge prior to

the installation. MTC to be submitted with the material.

Lacquered glass

Providing and fixing of 6mm thick toughned planilaque lacquered glass extra Sqm. 190 2,942.09 558379.83

white / coloured with ss edge protection in ss 316 grade. Sample to be submitted

5.4 MR from all the approved make for approval of engineer in charge prior to the

installation. MTC to be submitted with the delivery of material.

Providing & fixing decorative cork for wall made in Portugal or approved Sqm. 44 3,997.50 175889.82

Equivalent Cork wall covering with thickness of 3mm & size of tile

600mmx300mm . Cork base with agglomerate of cork & cork veneer on top

5.5 MR waxed or warnished . Dimensions conforming to EN427 & dimensional stability

conforming to EN434,Reaction to fire according to EN 13501-1-class Es2'd0 or

Ds1'd0. The product to be installed using an adhesive as would be

recommended by manufacturer.

Chipping for electrical and data trenches in PCC for average width of 400mm to rmt 180 364.10 65538.01

100mm and depth of 50mm to 75 to receive aluminum trays including junction

boxes. Rate quoted shall include for chipping and removal of debris from the

working area , including carting away from the site, as desired and making good

5.6 MR (in perfect condition). On inserting the trays, the balance portion to be neatly

plastered of mix 1:3 , in proper line and level with the PCC floor, including the

Providing and Fixing of Grooved Wooden Slats made out of Prelaminated 16 SQM 106 5,524.70 585618.11

mm Thick high density MDF Board of density , acoustic panel size will be

approved by engineer in charge, Grooving at an interval of 28 mm c/c as per

direction of engineer in chargel, The wooden acoustic panels to be backed with

black acoustic fleece. All joints of wooden acoustic panel should have dowel

connection to avoid any sagging /unevenness. All wooden acoustic panels

should be fixed on GI ‘Z’ clamp made out of 0.75 mm thick GI sheet of size 30

mm x 30 mm collar and 50 mm high to match with the installed GI frame. The

grooved acoustic panel laminated in desired shade as per Engineer In charge.

The ‘U’ channel grid of size – 50 x 32mm thick made out of GI sheet, 0.5 mm

thick. The grid size will be – 600 x 900mm fixed to wall using all screws of

Stainless steel. Cavity of grid shall be filled with 50mm thick compressed

Rockwool tile (UL certified fire retardant) of 60kg/m3 confirming to IS8183 as

infill to achieve the 1.0 NRC value and finally wooden acoustic panel fixed on GI

Channel grid as final finish. Sample to be submitted from all the approved make

or equavalent for approval of engineer in charge prior to the installation. MTC to

be submitted with the delivery of material.

Providing and Fixing of Grooved Wooden Slats made out of 11 mm Thick high SQM 40 6545.02 261800.7991

density MDF Board of density 700-750Kg/m3 and 04mm thick Vieneer at front

face, Total thickness will be 15mm, acoustic panel size :approved by engineer

in charge, Groove Size 3.2mm at an interval of 28 mm c/c & Vineer shall be

polished in melamine finish as per acoustic design / Architects approval, The

wooden acoustic panels to be backed with black acoustic fleece. All joints of

wooden acoustic panel should have dowel connection to avoid any sagging

/unevenness. All wooden acoustic panels should be fixed on GI ‘Z’ clamp made

out of 0.75 mm thick GI sheet of size 30 mm x 30 mm collar and 50 mm high to

match with the installed GI frame. The grooved acoustic panel laminated in

desired shade as per Engineer In charge / Architect’s approval. The ‘U’ channel

grid of size – 50 x 32mm thick made out of GI sheet, 0.5 mm thick. The grid size

will be – 600 x 900mm fixed to wall using all screws of Stainless steel. Cavity of

grid shall be filled with 50mm thick compressed Rockwool tile (UL certified fire

retardant) of 60kg/m3 confirming to IS8183 as infill to achieve the 1.0 NRC value

and finally wooden acoustic panel fixed on GI Channel grid as final finish. Panels

are tested and confierming NRC 1.0 as per IS:8225/ISO: 354/ASTM 423C, Test

report form OEM to be submitted. All makes and models of all items/samples

should be approved by the engineer-in-charge/consultant prior to the installation.

Providing and fixing decorative high pressure laminated shett of plain/ wood

grain in gloss/matt/suede finish with high density protective surfarce layer and

reverse side of adhesiv bonding quality conforming to IS:2046 Type S, including

cost of adhesive of approved quality.

Acrylic Solid Surface

Cladding P/F 6mm thick Corian sheet of approved color and shade over SQM 15 8923.39 133850.80

existing 8 mm MDF Board as per groove design pattern with adesev etc.

5.9 MR Complete with finsihing of groove and filled with matching duco

paint.Including corian edge molding over partition edge frames etc of size 75mm

Providing & Fixing solid laser cut in Corion with side lit up HAL logo etc Nos 1 15333.59 15333.59

complete…size 4' x 2'

Acoustic panels

P/F acoustic panels any size and shape in approved color with Standard size & Sqm. 195 3,951.13 770470.60

thickness of 9-12 mm. PNV acoustic Panels should have Sound Absorption

coefficient (NRC) (0.3- 0.94). Formaldehyde emission standards of GB18580-

2001 class E1, it is a green material with asbestos-free, non-toxic and tasteless

gas under extreme temperature, protecting the ozone layer, non-irritant and

recyclable. acoustic panels have to be Fire-resistant. Good insulation properties,

5.11 MR to prevent transmitting the heat from outdoor to indoor directly as partition or and

ceiling, saving 35% of energy, extending the life of air conditioning. acoustic

panels are Light weight and allow free cutting with paper knife. Sample to be

submitted from all the approved make or equivalent for approval of engineer in

charge prior to the installation. MTC to be submitted with the delivery of material.

5.12 MR CNC cut 3d accoustic panel - with single layer upto 9mm thk. Sqm. 20 6,599.71 131994.11

Aluminium skirting

Supply and fixing of modular aluminium skirting , 100 mm high x 5.5 thick, 1.2 Rmt 360 184.28 66339.52

5.13 MR mm wall thickness, snap fit assembly. Finished in anodizing or powder coating,

Marble for wall

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work

for wall lining (veneer work) including dado, skirting, risers of steps etc., in

design and pattern wherever required, stones of different finished surface

on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and

jointed with white cement slurry @ 3.3 kg/sqm including pointing with white

cement slurry admixed with pigment of matching shade, including rubbing,

polishing etc. all complete as per Architectural drawings, and as directed by the

Engineer-in-Charge.

18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark SQM 20 8823.75 176475.00

8.11.1 Emperadore etc.

Applying one coat of water thinnable cement primer of approved SQM 984 60.00 59040.00

5.15 13.43.1 brand and manufacture on wall surface. Water thinnable cement primer.

Acrylic emulsion paint

Wall painting with acrylic emulsion paint of approved brand and SQM 984 128.65 126591.60

5.16 13.60.1 manufacture to give an even shade : Two or more coats on new work

Providing and applying duco paint,as per pre-approved sample(s), all complete, Sqm. 20 354.09 7081.80

inclusive of 2 coats of duco putty, water cutting, sanding and final duco spray as

approved, and to the entire satisfaction of the Architects. The duco surface to be

5.17 MR applied with PU coat, in workman like manner, in matt finish (60 :40 ratio of matt

: glossy) complete as per the instructions

of, and, to the entire satisfaction of the Engineer in charge

MR Providing and fixing upt to 6mm thick POP Punning in line & plumb finished SQM 784 308.00 241472.03

smooth to receive paint.

6 FALSE CEILING

Gypboard ceiling

Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :

277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed

to the ceiling with dash fastener

12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to

the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at

450 mm centre to centre, shall be fixed in a direction perpendicular to

G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230

mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm

thick 27 mm high having flanges of 20 mm and 30 mm long.

Including jointing and finishing to a flush finish of tapered and square edges of

the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on

both sides of joint and two coats of primer suitable for board, all as per

a) manufacturer's specification and also including the cost of making openings

for light fittings, grills, diffusers, cutouts made with frame of perimeter channels

suitably fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with :

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board SQM 240 1286.20 308688.00

Micro perforated acoustic panel

Providing and Fixing of Micro Perforated acoustic panel made of minimum 16 SQM 265 4,841.13 1282898.75

mm thick high density Perforated MDF Board 700-750kg/m3 Density, having

Rear side Perforation Hole diameter will be 8-10 mm, Front finish Micro

Perforated 0.5 mm Thick Aluminium Sheet perforation diameter will be 0.6-0.8

mm at a distance of 02 mm c/c as per approval of rngineer in charge, The

micro perforated acoustic panels to be backed with black acoustic fleece. Micro

perforated Alu-wood acoustic panel size 600x2440 mm, All joints of acoustic

panel should have dowel connection to avoid any sagging /unevenness. All

acoustic panels should be fixed on GI ‘L’ clamp made out of 1 mm thick GI sheet

6.2 MR of size 50 mm x 50 mm collar and 50 mm high to fix with GI Channel / Steel

wire / Threaded rod to hang / fix with RCC Slab. The micro perforated Acoustic

Panel top sheet will be Powder Coted Aluminium Sheet in desired shade as per

Engineer In charge / Architect’s approval. Acoustic panel having 0.85 NRC

value with 50mm thick Rockwool pads for 1/3 Octive Hz. Sample to be

submitted from all the approved make for approval of engineer in charge prior to

the installation. MTC to be submitted with the delivery of material.

Supply of suspended acoustical Hanging Baffles made of Wooden Strips NRC Value SQM 265 6,523.43 1728709.88

–0.5- 0.80 NRC. The baffle made out of 5mm thick and 25mm wide wood strip having

3mm gap alternatively on both faces fixed on wooden batten. Rockwool of 48 Kg/m3

density confirming to IS 8183 , tissue fiber paper laminated filled in between wooden strips

as acoustic insulation to achieve desired NRC value. The Aoustic Wooden Baffles are

square in shape and design as per architects approval. Size of the Baffles

6.3 MR 1200x150x50mm thick, distance in between two baffles will be 150mm . Can be Installed

with Hanger Wire or Thred Rod. The Baffles to be suspended individually using the

Unistrut Channel with cable adjuster or locking Clip tied by Thred rod or Hanger Wire kit

comprising of hanger wire/cable adjuster/cable finishing hook.Sample to be submitted

from all the approved make or equivalent for approval of engineer in charge prior to the

installation. MTC to be submitted with the delivery of material.

Plywood ceiling

Providing and fixing plywood 4 mm thick, one side decorative veneer

6.4 8.28 conforming to IS: 1328 (type-1), for plain lining / cladding with necessary

screws, including priming coat on unexposed surface with :

8.28.1 Decorative veneer facings of approved manufacture sqm 95.00 1551.0 147,345.00

6.5 13.68 French spirit polishing :

13.68.1 Two or more coats on new works including a coat of wood filler SQM 95.00 351.15 33359.25

Stretch Ceiling

Supply & fixing position backlight stretch ceiling with aluminium profile & all SQM 19 5,542.00 105297.95

accessories,complete as per details drawing, as specified & as directed by

engineer in charge ,white code (489),Net weight 200-250/m2 , Afford weight

1.95kg/m2, Thickness 0.18mm, Fire resist,100% Recycleable,

Translucent rate 75%, Working temperature -30-60 degrees,

Acoustic wood wool board ceiling

ACOUSTIC WOOD WOOL BOARD CEILING - 0.9 NRC Providing & fixing of SQM 25 4,722.00 118050.00

wood wool acoustic Panel- MICRO 1200 mm X 600mm X 25 mm , 1 layer

magnesite bonded wood wool (Fiber width 1mm) panel as a composite product

consisting of mineral woolabsorber with trickle protection system. Panel will be

mounted on ceiling including providing and fixing duly painted /polished. Studs

will be a placed at distance of 600mm c/c using rigid fixing systems including

fixing rockwool slab with appropriate density making the cut outs for HVAC

grills/diffusers/ /service access doors, electrical appliances etc. wherever

necessary. Sample to be submitted from all the approved make or equivalent for

approval of engineer in charge prior to the installation. MTC to be submitted with

the delivery of material.

Specification :

Specification :

TCH (Total Construction Height) -200mm

Size : 600/1200 X 600 X 15mm thickness

Matrix weight : 7-7.8kg/m2

Edges : (5mm bevelled from all 4 sides)

Light Reflectance : upto80- 90%

Humidity Resistance : 80-90%

Colour of paint : Wooden colour natural look/Grey/Concrete Finish Spray paint

Reaction to fire acc to EnN 13501-1: B-s1,d 0

Sound Absorption value : NRC 0.85-0.9

Providing & fixing false ceiling at all height including providing & fixing of

framework made of special section, power pressed from M.S. sheets and

galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS :

277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges

of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash

fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed

to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I chanels

45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling

section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm

each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction

perpendicular to G.I intermediate channel with connecting clip made out of

2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter

channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the

6.8 12.59 perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm

centre, with 25mm long dry wall screws @ 230mm interval, including fixing of

Calcium Silicate Board to ceiling section and perimeter channels with the help of

dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to

a flush finish of tapered and square edges of the board with recommended

jointing compounds, jointing tapes,finishing with jointing compounds in three

layers covering up to 150mm on both sides of joints and two coats of primer

suitable for boards, all as per manufacture's specification and also including the

cost of making opening for light fittings, grills, diffusers, cut outs made with

frame of perimeter channels suitably fixed, all complete as per drawings,

specificaton and direction of the Engineer in charge but excluding the cost of

Calcium Silicate Board

8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials SQM 32 1273.05 40737.60

6.9 12.59.1 reinforced with cellulose fiber manufactured through autoclaving process.

7 DOORS & WINDOWS

7.1 MR Sliding / Movable wall Acoustic Partition

Sliding / Movable wall Acoustic Partition of with Sliding Glider type vertical SQM 18 28,710 516780.27

panels, Top Mounted, Sliding Panels having 100mm thickness. The wall internal

built is consisting mechanism to move top and bottom seal manually operated by

handle inserted in the panel style, turning the handle through 45 degree shall

simultaneously extend or retract the top and bottom seals through steel and

spring mechanism, which shall firmly hold the seal in the retracted seal or

extended mode. The panel trim shall be standard series with exposed aluminum

trims finished in 6063-T5 aluminum shall be used.

Each panel consisting top and bottom epdm rubber retractable seal with

concave/convex vertical interlocking profiles.

Vinyl seal of butane rubber shall be used at top and bottom and as well as closer

seals for operable wall system. Retractable seal drop shall be 20mm.Width of

panels shall be 900-1200 as approval of Engineer-in charge. Panels shall be

made from 12mm MDF board hung in acoustic isolation from the frame and

allowed to vibrate independently of the frame. Each panel shall be suspended on

extruded 6063-T5 Aluminum track; steel cold ball bearing roller/trolley of material

NYLON wheal made with base material of POM 45 tempered steel, maintenance

free with Single Pin/Double Pin ball bearings as per design of Centre Stacking

OR side Stacking The final finish of sliding panel will be 09mm thick

Compressed Polyester fiber pad in desired color shade and design pattern . The

total thickness of partition along with polyester pad on both faces will be 118mm

. The acoustic design of sliding partition should certified by CSIR laboratory for

Min. 48 STC rating as per IS: 9901(Part-III)-1981, DIN: 52210 part VI-1989, ISO:

140(Part-III)-1995. MS angle structure and Pin Board/MDF baffling filled with

Rockwool 64kg/m3 density above the sliding partition for controling the sound

from one side to other side. Sample to be submitted from all the approved make

or equavalent for approval of engineer in charge prior to the installation. MTC to

be submitted with the delivery of material.

7.2 Glass door (toughened glass)

Providing and fixing 12 mm thick frameless toughened glass door shutter of sqm 36.00 4,447.90 160124.40

approved brand and manufacture, including providing and fixing top & bottom

pivot & DOUBLE ACTION HYDRAULIC FLOOR spring type fixing arrangement

and making necessary holes etc. for fixing required door fittings, all complete as

per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid

SINGLE LEAF FRAMELESS GLASS DOOR

CORNER PATCH LOCK WITH CYLINDER FO 10-12 MM GLASS, SS MATT PC 17 4,892.93 83179.89

PULL HANDLE BACK TO BACK FIXING 25MM DIA X 300MM C/C, SS MATT PC 34 1,843.49 62678.50

SINGLE LEAF FRAMELESS GLASS DOOR

CORNER PATCH LOCK WITH CYLINDER FO 10-12 MM GLASS, SS MATT PC 5 4,892.93 24464.67

PULL HANDLE BACK TO BACK FIXING 25MM DIA X 300MM C/C, SS MATT PC 10 1,843.49 18434.85

TOTAL NO. OF DOORS PC 5

WPC Door frame/ WPC Chowkhat

3. WPC CHOWKHAT a complete replacement of Timber, Steel and Stone;

Providing factory made solid WPC based Door frame of

7.5 MR (Wood Polymer Composite composed of rice husk and thermo plastic

single extruded which should be termite proof, water proof, fire

retardant Grade and Screwable/Nailable of or equivalent grade],

WPCChowkhat to be of density 725 kgs/cum. With GREHA Council

certification and 2200 N screw holding capacity on the face and 1500N on edge.

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with

rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood Cum 2.20 165255.05 363561.11

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) decorative type, core of block board construction with

7.7 9.20 frame of 1st class hard wood and well matched teak 3 ply veneering

with vertical grains or cross bands and face veneers on both faces of

35 mm thick including ISI marked Stainless Steel butt hinges sqm 36 3,023.95 108862.20

9.20.1 with necessary screws

Providing wood work in frames of doors, windows, clerestory windows

and other frames, wrought framed and fixed in position with hold fast

7.8 9.1 lugs or with dash fasteners of required dia & length ( hold fast lugs or CUM 0.45 130183.05 58582.37

dash fastener shall be paid for separately).

Providing and fixing wooden moulded beading to door and window frames

with iron screws, plugs and priming coat on unexposed surface etc.

9.40.1 2nd class teak wood

DOOR CLOSERS Providing and fixing aluminium extruded section body EACH 18 851.60 15328.80

tubular type universal hydraulic door closer (having brand logo with ISI, IS :

3564, embossed on the body, door weight upto 36 kg to 80 kg and door width

from 701 mm to 1000 mm), with double speed adjustment with

necessary accessories and screws etc. complete.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of

10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head,

8.1 10.27 comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame ,

concrete/ masonry, etc. as per direction of Engineer-in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed

8.2 10.2 work, including cutting, hoisting, fixing in position and applying a priming coat of approved Sqm 5.00 101.75 508.75

steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,

8.3 10.16 including cutting, hoisting, fixing in position and applying a priming coat of approved steel

primer, including welding and bolted with special shaped washers etc. complete.

10.16.2 Hot finished seamless type tubes Kg 25.00 157.50 3937.50

MORTICE LOCK AND LEVER HANDLES Providing EACH 18 5172 93098.16

and installing Tubular Handle TH 123 with Roses & Escutcheon in SS packaged

with Mortice lockset 55mm backset, 20 SS forend, SS strike plate and EP

Cylinder for all flush doors.

HANDLES;- Providing and fixing bright finished brass handles with screws

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked,

anodised (anodic

coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade, with necessary screws etc. complete :

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor EACH 18 106.70 1920.60

8.7 9.82 door stopper

with necessary screws, etc. complete.

8.8 MR SINGLE LEAF METAL FIRE RATED DOOR - 1200x2400mm

Supply of 46mm thick Metal fire check door of 120 minutes fire rating confirming

to BS: 476 Part 22 and IS: 3614 Part II fabricated with 2 nos. 22 gauge thick

galvanized sheet with infill of fire rated Acrylic Sealant and non-combustible core

bonded to both faces of sheet with lock seam joints at stile edges and internal

reinforcement at top, bottom and stile edges for Fire Rating. The door frames are

manufactured from 18 gauge thick galvanized steel sheet pressed form to

double rebate profile of size 143mm x 57mm. The door frames and door shutters

are finished with powder coated off-white finish.

Vision panel : The door to have vision panel of 300mm x 200mm" with 12 mm

thick Glass. Glass also to have 2 hr fire rating Hardware: Door to be complete

with approved hardware as follows: 4 nos. 100x75x3mm SS Ball Bearing butt

Hinges, surface mounted door closer, SS lever solid handles with rosettes &

escutcheon, 4P mortise lock sets with strike plate, 60mm long Key Cylinder and

Floor Mounted Door Stopper in SS with hard rubber insert. Sample to be

submitted from all the approved make or equivalent for approval of engineer in

charge prior to the installation. MTC to be submitted with the delivery of material.

Fire Rated Doors - Galvanised Steel Fire Rated Fully Glazed Doors -2hr

Providing and fixing of tested fully glazed steel fire rated double leaf door sqm 5.6229 49049.27 275797.2001

with 120 minutes of

integrity and radiation control (EW 120) fabricated with 1.6 mm thick

galvanized steel sheet. The door frames are manufactured from 1.6 mm

galvanized steel sheet pressed to form a profile of 35 mm x 60 mm on the

venical sides and 50 x 60 mm on the horizontal side. The door shutter

would have a top rail and side rail 60 mm x 60 mm and a bottom rail of

110 mm x 60 mm. The sections have a special insulating infill. The overall

door opening is 2400 mm x 2600 mm. The test is conducted in IFTS as

The glass should be, 11 mm clear 120 min fire rated

(EW 120) Non Wired Toughened Interlayered glass with a light

transmission of 86% and a sound reduction of 37 dB and manufactured

in UL & TUV audited Facility and including UL-EU Cenification. The glass

should be compliant to class 2(B)2 category of Impact Resistance as per

EN 12600. The glass should be held in its place with the help of 1.6 mm

GI beading and a special ceramic tape with cross section of 5 x 20 mm as

per the test evidence. The maximum glazing size should be not more

than 1100 mm x 2200 mm (w x h) or 2.42 sq mt in total area which should

be clearly mentioned in the test cenificate.

The shutters should be fixed to the frame using SS Ball Bearing Hinges

of size 100 mm x 89

mm and 3 mm thickness or equivalent. Beading should be attached using

4 mm x 35 mm SS screws at a distance of 75 mm from the edges and

150 mm c/c hencefonh. The door should be fitted with Mortise Sash lock

and door closer of make or equivalent. The inactive leaf should be fixed

to the frame using 1200mm long tower bolt . The test report will be

considered valid only if it contains the stamp and signature of the

authorized signatory from the make.

Door Size:- 2000 mm x 2400 mm

FIXTURES FOR DOORS

Providing and fixing of SS Ball Bearing Hinges of 100 x 89 x 3m SUS

304 Grade complete with SS Screws ( 4 Nos per panel )

Providing and fixing of door closers tested in accordance with BS: 476

Pan — y2 1987 with manufacturers warranty and tested with complete

assembly offerred by manufacturer

Providing and fixing of Lock 952 F alongwith 80mm Cylinder and

necessary screws as

concealed flush bolt with extension rod upto 600 mm long.

9 MISCELLANEOUS

Supplying the premium quality manually operated Roller blinds with HDAP SQM 80 10,977 878195.47

Chrome protection fabric of S high tenacity Polyester Yarn with PVC Coating

&Aluminium Backing, . Fabric shall have visible light & solar properties and

should pass NFPA 701 fire resistance test. The control engineered heavy duty

chain drive pulley operating system with a ball chain can be placed at either side

of the blind. Its bracket and roller tube must be rust proof and should be

adjustable. TECHNICAL SPECIFICATION OF SUNSCREEN BLINDS :

9.1 MR COMPOSITION : 28% POLYSTER AND 68% PVC, 4% aluminium layer on the

back OPENESS FACTOR : 5%, THICKNESS : 0.53 +/- 5%, COLOUR

FASTNESS TO LIGHT – GRADE 8, ANTI ULTRAVOILET – 95%, WEIGHT –

380 G/SQ.MTR +/- 5%, CLEANING INSTRUCTION – WASHABLE, MAKE AS

PER THE SIZE OF THE WINDOWS. Mount Type :Wall Mount & Ceiling Mount,

Auto Locking, Folds up in Classic Roller style, Fabric Type :Water Repellent

9.2 MR Motor for roller blinds Nos. 2 25,783 51566.00

Motorization (for MD cabin) Tubular Motor(RTS) for Roller Blinds / Motor

Specs : PREMIUM Motor DM-35R-6/28 . Radio Transmission System

Torque(Nm) 6Nm SPEED (RPM) 28mm Rated Voltage (230 Volt) Power

Consumption(W)121 (W) Rated Current ( A) 0.53 amp Running time before

thermal cut of (4 min.).

Rated Frequency ( 50 Hz) Degree of Protection – IP44 , Silent motor

Multi channel remote to operate motors of roller blinds as per the suppliers Nos. 2 4,193 8386.00

9.4 Frosted film (Crystal quality)

Providing and fixing scotchcal over glass surface as approval of the engineer in SQM 20 2,098 41964.11

9.7 MR P/f of PVC film on Laquered Glass SQM 33 2,375 78358.91

Digital print over glass

Providing and fixing 3M scotchcal coloured digitally printed over glass / solid SQM 70 2,098 146874.39

surface as engineer in charge.

Transition profiles for floor

Providing and fixing pre-approved bought out transition profiles of SS for joints Rmt 204.00 380 77520.00

on the floor between flooring of two different materials. The transition profile to

have flanges to overlap over both the materials on either side as engineer in

charge.. Approx width of 32 mm / PREFERRED SOLID straight SS strip 8-

10mm thk, height as per fixing detail, required as per locations

Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer Rmt 50 632.56 31628.00

board ISI marked IS : 14842, including top cover of 6 mm coir veneer

board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with

9.10 9.43 nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm

long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm

x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all

STONE MURAL. 5911.39 975378.95

Concept Creation

Creating design and creation of Art work concept on given

subject. With initial visit to site, preparation of various designs

with different material, providing the samples, t for

approval, improvisation in short listed creative’s and making of

final design for final production by enlargement of drawing as

per ratio of actual size, to prepare detailed working shop

drawings (full scale) based on the Concept drawings / Views /

site conditions, display of actual size dummy /mock up

Fabricated in sun board with digital print for client approval

Artwork Execution

Towards the cost of execution of artwork in stone (any stone

dholpur/granite/Italian or any other stone which the artist find

appropriate for executing the artwork thickness 12 mm to 19 mm or more. ) by

qualified sculpture/artist .The cost includes

execution and installation at site. Cladding of stone can be dry

or wet procedure as per site condition and size of artwork.

Creating design and creation of Art work concept on given subject. With initial visit to site,

preparation of variousdesigns with different material, providing the samples, layout for

approval, improvisation in short listed creative’s and making of final layout for final

production by enlargement of drawing as per ratio of actual size, to prepare detailed

9.12 MR working shop drawings (full scale) based on the Concept drawings / Views / site Sqft 108.00 3814 411921

conditions,displayof actual size dummy /mock up Fabricated in sun board with digital print

for client approvalART WORK EXECUTIONTowards the cost of doing canvasPAINTING

by qualified artist including frameand installation at site

Supplying of designer wallpaper as per approved samples contains 10%

recycled content, Nonwoven/acrylic fabric total weight 8-15 oz/sqryard,

thickness- .02 inches, meets section 01350 IAQ test requirements , water based,

MR ready to use and works with a variety of substrates, have microbial prperties and

zero VOC, easy to install with adhesives.

Providing and fpxing Full or half height Storage /Cupboard: P/F of storage unit 600mm

deep consisting of double leaf openable shuttered finished with 1mm thick approved

laminate of as per make list on front faces over 19mm thick board frame on top shall be

finished with 12 mm thick acrylic surface ,bottom & sides and 6mm thk ply on back side of

cabinet using approved board or equivalant including drawer units,shelves finished colour

9.14 MR as per Interior dwg. with necessary hardwares of as per make list like concealed Hinges, sqm 11.00 7,341.00 80,751.00

magnetic catcher,locks,handles, knobs complete etc. at all aspects. All internal and back

sides shall be white laminate or enamal paint of approved brand . All exposed surface to

be treated with anti termite and fire reterdant paint before laminate , etc

Central theme ceiling

Central theme ceiling in stretch ceiling or acrylic and metal framing with back lid Sqm. 15 8485.80 127287.05

Providing and fixing 'EXIT' letters signage (With 'or' without directional arrows as

per signage plan). signage to be made of 3mm thick foam board with edge to

edge self adhesive self- luminescent Forex or equivalent vinyl stuck on it. Fix

10.1 Green vinyl to cover Forex vinyl leaving 6mm border around edges with 'EXIT'

letters cut-out. (Note : 'EXIT' letters to be self-luminescent and not the

background). 'EXIT' letters height shall be 150 HT.

Type - 3 - Double sided ceiling suspended constantly Nos 5 2518 12592.11

10.2 MR lit with battery support for 120min with single arrow.:- 8" X 15"

Supplying and fixing of Room Signages in imp.aluminum profile with 3 mm Nos 20 649 12980.67

10.3 MR acrylic Gents/Ladies pictograph printed on canvas (Room Names) - Include

braile letterings Size is 6"x10".

Rest Room - Include braile letterings

Floor Signae type - 2 - 4mm thk. Acryllic cut letters 178mm high, painted to Nos 1 650 650.00

10.5 MR app. Color & logo with aluminium - SS back with through cut letters (Lift Lobby).

Include braile letterings

Fire Exit ID - 4mm thk. Acrylic base with autoglow vinyl cut letters. Nos 2 1300 2600.00

14"x8".Include braile letterings

Fire Extinguisher Signage -Providing and fixing graphical Triangular signage Nos 4 399 1594.52

for fire extinguisher. signage to be made of 3mm thick foam board with edge to

edge self adhesive self-luminescent Forex or equivalent vinyl stuck on it. Fix

Green vinyl to cover Forex vinyl leaving 6mm border around edges with 'FIRE

EXTINGUISHER' letters cut-out. (Note : 'FIRE EXTINGUISHER' letters to be self-

luminescent and not the background). 'FIRE EXTINGUISHER' letters height

shall be 100mm in HT. 153 X 153

Advisory / notice signage - 4mm thk. Acrylic base with autoglow vinyl cut Nos 1550 0.00

letters. 19"x8"

Providing and fixing SS PUSH/PULL signage for all doors. Size 2"x 6" Nos 41 304 12449.64

MR S12b-Evacuation Map Nos 2 2239 4478.47

Providing and fixing evacuation maps of size A3 size, signage shall be made of

3mm thk foam board on to which on to which evacuation plans printed on

coated paper shall be stuck. The signage shall be laminated including the edges.

signage shall be fixed with 3M double sided adhesive tape.

IN CASE OF FIRE USE STAIRS' photo luminescent sign size: 10"x10"mm I sign Nos 2 1290 2580.00

aluminum profile with 3mm acrylic

Panic bar door signage - Emergency Door To Be Used Emergency Only /In the Nos 2 780 1560.00

time of emergency please used staitcase Aluminium.20"x8"

Providing and fixing three dimensional signage in Acrylic Sheet finish to match Nos 1 75,000.00 75000.00

brand colour shade of size approx. 750 mm x 900 mm as per clients artwork.

10.13 MR Average thickness of Signage letter 25 mm acrylic with back lit & laser cut as

Three dimensional signages in 3mm thk Aluminium sheet complete as per Nos 1 52,999.12 52999.12

design and drawings. Average thickness of Signages letter 25 mm SS, laser

welded signage in given artwork & approved sample (Average size 750 x

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE B , TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE BLOCK 1 , NEW DELHI

S.NO DISCRIPTION QTY RATE AMOUNT IMAGES

CMD CABIN FURNITURE

CMD Cabin Table

Main Table with mobile pedestal :- 3000x1200x750

Side Unit (Over all size):- 2700(1500+1200)x600x650 ht

Table -Table top made of 25 mm thick mdf board with Veneer.

Gable End :- Gable end made of 25 mm thick mdf board with both side Veneer finish.

Modesty :- Modesty made of 19 mm thick mdf board with both side Veneer finish.

Side Credenza - Side Credenza Top made up of 19mm thick with mdf board with Veneer finish. Storage carcass & shutter is 19mm thick

mdf board with veneer finish.

Mobile Pedestal :- Pedestal are made of 19 mm thick with thick with mdf board with Veneer finish. Mobile Pedestal having 2 drawer +

1 Filing drawer. The Pedestal is made mobile with the use of castors. The drawer units are provided with Center locking arrangement.

The Drawers are Provided with C shape Handle.

Natural Wood Veneer & Lacquer Painting,

optional Leather Writing Pad on Desktop, Solid Wood

Under Structur Hettich 3 Section Sliding Rail,

FGV Damping Hinges & BMB Lock

Cabin Back Storage :- 2400x520x750 ht

Back storage :- Storage Top made up of 19 mm thick with mdf board with Vneer finish.

Understructure :- Storage carcass & shutter is 19 mm thick mdf board with veneer duly finish.Storage have openable shutter with

locking arrangement & 19 mm thk.shelf in mdf.

COFFEE TABLE : 800 X 800 X 450 HIGH CENTRAL COFFEE TABLE in 18 MM mdf with matching veneer and polish ; with 10 mm

toughened glass on ss studs etc as per design

CORNER TABLE : 400 X 400 X 450 HIGH CORNER COFFEE TABLE in 18 MM mdf with matching veneer and polish ; with 10 mm

toughened glass on ss studs etc as per design

CMD CHAIR :High Back Chair

Genuine Leather Upholstery, Aluminum Alloy Five Star Base, Height Adjustment and Synchro Tilt Mechanism with Multi Position Locking

And Automatic Tension Control, Veneer Finished Arm Rests with PU Padding-775*715*1185

CMD VISITOR CHAIRS at Table Medium Back Chair

6 Genuine Leather Upholstery, Aluminum Alloy Five Star Base, Height Adjustment and Synchro Tilt Mechanism with Multi Position Locking NOS. 4 86992.4615 347969.846

And Automatic Tension Control, Veneer Finished Arm Rests with PU Padding- 775*745*995

VISITOR SOFA SEATING -Two Seater Sofa In Genuine Leather With Lacquered Metal Legs. Solid Wood & Plywood Inner Structure-

OTTOMAN SEAT : OTTOMAN CHAIR AND FOOT STOOL IN WOOD FRAME & HIGH DENSITY FOAM COVERED WITH ; CHOICE FABRIC;

LEATHER UPHOLSTERY AS DIRECTED AS PER SELECTION

R. MANAGER CABIN FURNITURE

RMGR Cabin Table

Main Table with mobile pedestal :- 2800x1200x750

Side Unit (Over all size):- 2700(1500+1200)x600x650 ht

Table -Table top made of 25 mm thick mdf board with Veneer.

Gable End :- Gable end made of 25 mm thick mdf board with both side Veneer finish.

Modesty :- Modesty made of 19 mm thick mdf board with both side Veneer finish.

Side Credenza - Side Credenza Top made up of 19mm thick with mdf board with Veneer finish. Storage carcass & shutter is 19mm thick

mdf board with veneer finish.

Mobile Pedestal :- Pedestal are made of 19 mm thick with thick with mdf board with Veneer finish. Mobile Pedestal having 2 drawer +

1 Filing drawer. The Pedestal is made mobile with the use of castors. The drawer units are provided with Center locking arrangement.

The Drawers are Provided with C shape Handle.Entire set in

Natural Wood Veneer & Lacquer Painting,

optional Leather Writing Pad on Desktop, Solid Wood

9 Under Structur Hettich 3 Section Sliding Rail, NOS. 1 254827.6965 254827.6965

FGV Damping Hinges & BMB Lock

COFFEE TABLE : 800 X 800 X 450 HIGH CENTRAL COFFEE TABLE in 18 MM mdf with matching veneer and polish ; with 10 mm

toughened glass on ss studs etc as per design

RMGR CHAIR :High Back Chair

11 Genuine Leather Upholstery, Aluminum Alloy Five Star Base, Height Adjustment and Synchro Tilt Mechanism with Multi Position Locking NOS. 1 89426.713 89426.713

And Automatic Tension Control, Veneer Finished Arm Rests with PU Padding-775*715*1185

RMGR VISITOR CHAIRS at Table Medium Back Chair

12 Genuine Leather Upholstery, Aluminum Alloy Five Star Base, Height Adjustment and Synchro Tilt Mechanism with Multi Position Locking NOS. 4 86992.4615 347969.846

And Automatic Tension Control, Veneer Finished Arm Rests with PU Padding- 775*745*995

13 VISITOR SOFA SEATING -Two Seater Sofa In Select Fabric WOOD Legs. Solid WOOD & Plywood Inner Structure-1520*880*790*440 NOS. 2 43560.29 87120.58

CONFERENCE ROOM

Table Size:- 9000(L)x1800(D)x750(Ht)

Table Top:-to be made in 43 mm thick 25 mm thick mdf with veneer finish with 18 mm thick mdf base.

Box Leg - made of 19 mm thick mdf board with veneer finish both side

Modesty :-made of 19 mm thick mdf board with veneer finish both side

Wire management :-Metal Flipper of 400 x 120mm without switch socket with metal cable tray below Table top for Electrical points

14 with metal wire riser for carrying wires. NOS. 1 518879.925 518879.925

Medium Back Chair

Chair Back : The back of the chair is upholstered with Leathrite. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Leathrite and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Knee Tilt mechanism with any position lockingand Chrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

15 Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment. NOS. 31 23701.9225 734759.5975

Arm rest : Chrome + PU arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

High Back Chair same as above but HIGH BACK

Chair Back : The back of the chair is upholstered with Leathrite. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Leathrite and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Knee Tilt mechanism with any position lockingand Chrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

16 Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment. NOS. 2 28057.9515 56115.903

Arm rest : Chrome + PU arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

EXECUTIVE MEETING ROOM

TABLE FOR EXECUTIVE MEETING ROOM

SIZE- 1500W X 1500D X 750HT

Specifications:

Table top - The work surface will be in veener 4mm thick over 25 mm mdf/./ply base both sides . confirming to IS-14587:1998. The

density of veener will be 680kmm g/m³. Surface: CPL( continuous pressure laminate) in 0.5mm thickness in veener finish. The veener will

be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-12823:1990. . Edges to be

finsihed in matching veneer/ wood edge band as per design

17 Under Structure - • in 18 mm mdf//ply box 600 x 600 supporting top and f/inished in veneer and polish to match table top NOS. 1 80074.0625 80074.0625

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays will be provided when the

cable access is required from the top through ‘Flip ups”. The Switch/socket slots are provided as a part of the “Flip Up” design just below

the flip covers. The “flip up” should be made in aluminum flip covers with soft closing arrangement. The “Flip up” cover will be anodized

in Silver grey finish to 20 microns confirming to IS 1868:1996, EN—2373-1 and IS 2360.

MEETING ROOM -MEDIUM BACK CHAIR Chair Back : The back of the chair is

upholstered with net. Back shall have lumbar support. Chair Seat : The Seat of the chair is

upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep cushioned in seat comfort to body

contours for proper alignment, posture and all day comfort. Base : The chair is featured with Synchro Tilt

mechanism with with any position locking and Chrome Base. The prong (base) is made of Chrome. The telescopic bellow is 3 piece

telescopic type and injection molded in black polyurethane.Gas lift : The chair is featured with Gas lift mechanism for Seat height

18 Arm rest : PU adjustable arm rest. NOS. 8 30748.44 245987.52

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

Storage :1200x520x750

Top :- Storage Top made up of 19 mm thick with mdf board with Veneer with polish finish.Understructure :- Storage carcass & shutter

is 19 mm thick mdf board with veneer finish.Storageto have openable shutters with locking arrangement & 19 mm thk.shelf. self

closing hinges; continuous alum g channel handle etc as per design/ direction

DIRECTORS ROOMS FURNITURE (SINGLE / SHARED )

TABLE FOR DIRECTORS WITH PARTITION f0r shared directorroom & without partition for SIngle DIRECTOR ROOMS

SIZE:- 1500-1800W X 900DX 750HT / SIDE STORAGE:- 1200W X 450D X 650HT

Main table. The table design should have options of different profiles. The work surface will be in veener 25mm thick one side .

confirming to IS-14587:1998. The density of veener will be 680kg/m³. Surface: CPL( continuous pressure laminate) in 0.5mm thickness in

veener finish. The veener will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

12823:1990. PVC edge band will be minimum 2 mm thick confirming to DIN 68861, 53388 standards. The edge band will be fixed to the

work surface edges all round with hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI D 4499 for viscosity and thermal

stability. The edge band will be done in continuous feed edge band machines for achieving the quality of workmanship.

Supports: The cabin tables are supported by the Legs which are built by using high pressure die casting connectors, specially tooled &

specifically designed Oval shape ERW Tube – 16g, along with strong Leg bush & levelers. High pressure aluminum die cast connectors

are of ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS 11035 – 1190. For chemical composition and IS 1608 –

2005 for UTS & Ys. The Integrate oval tube will also be used as cross beams connecting both ends legs. The design of cross member

should be structurally strong to negate use of intermediate leg support.

20 Finish: All metal components & aluminum die cast parts will be powder coated by Nano ceramic surface treatment process compiled to

a Bend test-ASTM D3451 – 06, Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-hazardous, environmental

friendly and will have uniform powder coating thickness of 50-60-microns.

Side Storage: storage as per requirement can be provided subject to availability of adequate space. (Optional). Normally the height will

be low or medium height- 750 – 1200 mm. The back low storage will be a composite storage 1200(L) x650(H)x450(D) mm. The storage

will be made in 25 MM veener (Pre laminated board) with the density of 680kg/m³ and 25mm thick one side . confirming to IS-

14587:1998. Surface: CPL (continuous pressure laminate) in 0.5mm thickness in veener finish. The veener will be confirming to E-1

Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-12823:1990. The storages will be supported by M8

Levellers insert moulded in PP. The composite low storage will have three equal drawer unit 400(W)x 450(H)x 430(D) and 1100 mm

storage with sliding shutters. The drawer boxes will be with sleek telescopic channels zinc passified- tested as per BIFMA standards for

75000 cycles with load of 470 kg/m³ (15 kg load). The drawer facia will be in 25 mm veener with finger grooves handle provision for

ease of opening. The drawer unit will be provided with multi lock cycle tested for 5000 times with key access.

Back Storage AT SHARED DIRECTORS ROOM :- 1200x520x750 ht Top Storage Top made up of 19 mm thick with mdf board with

Veneer finish.to natch table above,Understructure :- Storage carcass & shutter is 19 mm thick mdf board with veneer duly

21 finish.Storage to have openable shutter with locking arrangement & 19 mm thk.shelf. NOS. 2 37026.2465 74052.493

Director Main Chair High Back Chair- Chair Back : The back of the

chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism with any point locking system and Chrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

Director Visitor Chair

Medium Back Chair

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism with any position locking and Chrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

CoffeeTable With 2 nos Chair ( one set )

Chair Back : The back of the chair is upholstered with Fabric.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Chair Frame: Made of wooden Frame duly polished.

24 Table Frame :- Made of wooden Frame duly polished. 450 DIA set 3 63803.013 191409.039

EXECUTIVE ASSISTANT ROOM FURNITURE ( NEAR CMD CABIN)

Cabin Table :- 1650x750x750

Side Table :- 1000x450x750

Table Top:-Table top made up of 25mm thick prelaminated partical board with 2mm thick pvc edge banding tape

Leg - 60x30mm Tapered Legs duly MS powder coated with connecting beam.

Modesty :- Table having 18 mm thick prelminated partical board.Modesty ht is 600 mm ht.

Side Table :- Side Table Top made of 25 mm thick prelaminated partical board,all exposed edges sealed with 2 mm thick pvc edge

25 banding tape.Side table having Fixed Pedestal.Pedestal are made of 18mm thick PLPB with 2 drawer + 1 filling Drawer.The drawer units NOS. 1 37026.2465 37026.2465

are provided with Center locking arrangement. The Drawers are Provided with C shape Handle.

Table :- 1200x600x750 ht with Mobile Pedestal :- 400x450x600(Ht)

Table Top:-Table top made up of 25mm thick prelaminated partical board with 2mm thick pvc edge banding tape.

Leg - 60x30mm Tapered Legs duly MS powder coated with connecting beam. Table is without modesty.

Mobile Pedestal :- Pedestal are made of 18mm thick PLPB having 2 drawer + 1 Filing drawer. The Pedestal is made mobile with the use

of castors. The drawer units are provided with Center locking arrangement. The Drawers are Provided with C shape Handle.

HIGH BACK CHAIR

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism system with any position locking andChrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

MEDIUM BACK CHAIR

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism system with any position locking and Chrome Base. The prong (base) is made

of Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

28 Arm rest : PU adjustable arm rest. NOS. 3 11146.3095 33438.9285

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

STAFF AREA CABIN ROOM FURNITURE

SIZE:- 2100-1800W X 900DX 750HT / SIDE STORAGE:- 1200W X 450D X 650HT

Main table. The table design should have options of different profiles.in high 25 mm MDF post formed laminate f/inish. The edge band

will be fixed to the work surface edges all round with hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI D 4499 for

viscosity and thermal stability. The edge band will be done in continuous feed edge band machines for achieving the quality of

Supports: The cabin tables are supported by the Legs which are built by using high pressure die casting connectors, specially tooled &

specifically designed Oval shape ERW Tube – 16g, along with strong Leg bush & levelers. High pressure aluminum die cast connectors

are of ADC-12 material confirming to ASTM E 1251-2011, IS 7658-1990 & IS 11035 – 1190. For chemical composition and IS 1608 –

2005 for UTS & Ys. The Integrate oval tube will also be used as cross beams connecting both ends legs. The design of cross member

should be structurally strong to negate use of intermediate leg support.

Finish: All metal components & aluminum die cast parts will be powder coated by Nano ceramic surface treatment process compiled to

29 a Bend test-ASTM D3451 – 06, Adhesion -DIN EN 14901 Salt spray test- DIN EN ISO 9227, which is non-hazardous, environmental NOS. 7 179173.7223 1254216.056

friendly and will have uniform powder coating thickness of 50-60-microns.

Side Storage: frame in 18 mm mdf with laminate. top in 25 mm MDF in post formed laminate to match table.The storages will be

supported by M8 Levellers insert moulded in PP. The composite low storage will have three equal drawer unit 400(W)x 450(H)x 430(D)

and 1100 mm storage with sliding shutters. The drawer boxes will be with sleek telescopic channels zinc passified- tested as per BIFMA

standards for 75000 cycles with load of 470 kg/m³ (15 kg load). The drawer facia & sides will be in laminate with finger grooves handle

provision for ease of opening. The drawer unit will be provided with multi lock cycle tested for 5000 times with key access.

BACK & SIDE STORAGE : SPECS SAME AS ABOVE ; WITH FILE STORAGE DRAWERS/ SHUTTERS AS PER DESIGN IN THE FOLLOWING SIZES

30 / OR AS PER SITE MEASUREMENTS TO MATCH - (Material MDF 25 MM thick top & rest all 18 mm MDF WITH EDGE BANDING .

HIGH BACK CHAIR

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism system with any position locking andChrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

MEDIUM BACK CHAIR

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism system with any position locking and Chrome Base. The prong (base) is made

32 of Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane. NOS. 14 11146.3095 156048.333

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

STAFF AREA WORKSTATION MODULES

WorkTop (1600x600):- Table top made up of 25mm thick POST FORMED prelaminated partical board with 2mm thick pvc edge banding

Side Top 750(L)x450(D) :- Table top made up of 25mm thick POST FORMED prelaminated partical board with 2mm thick pvc edge

Loop Leg:- The understructure stright legs shall be made of CRCA pipe section of size 60x30mm of thickness 1.2mm. The leg shall be

connected with beam of thickness 1.2 mm. All these legs and beams shall be fitted to each other by connectors and necessary

hardwares. The legs shall be having adjustable leveler shoe. This leveler shoe shall be provided at bottom of leg which allow 10-20mm

adjustment for floor unevenness.The all legs and beams shall be duly finished with powder coating in desired shade/colour. Powder

coating shall be 40-60microns thickness.

Fixed Metal Pedestal :- Providing and placing Metal Pedestal with an overall size 750(w) x 450(d) x 725(ht)mm with 2nos of drawers & 1

filling Drawer. Pedestal shall be on the levellers. Pedestal facia have recessed type in built handle with locking arrangement. Metal

pedestal having facia in 1mm and rest of the body and inner drawer are made of 0.8mm thick

CRCA powder Coated with 40-50 microns .The Pedestal Drawers

are mounted on metallic roller slides on both sides.

Metal Drawer Storage (Side Storage) :- Storage Top made up of 25mm POST FORMED Prealam partcle board thick with 2mm thick pvc

edge banding tape PLACED / F/IXED OVER Metal Drawer storage with 2nos of drawers .Pedestal shall be on the levellers. Pedestal facia

have recessed type in built handle with locking arrangement. Metal pedestal having facia in 1mm and rest of the body and inner drawer

are made of 0.8mm thick CRCA powder Coated with 40-50 microns .The Pedestal Drawers are mounted on metallic roller slides on both

i 1350-1200(L)X450(D)X750(HT) ( Prelam partcle board with laminate finishes as per approved shades. NOS. 52 10810.63903 562153.2296

STAFF AREA WORKSTATION CHAIRS

HIGH BACK CHAIR

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism system with any position locking andChrome Base. The prong (base) is made of

Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment.

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

MEDIUM BACK CHAIR

Chair Back : The back of the chair is upholstered with net. Back shall have lumbar support.

Chair Seat : The Seat of the chair is upholstered with Fabric and cut foam on 12mm thick BWP Plywood. The chair shall have deep

cushioned in seat comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Synchro Tilt mechanism system with any position locking and Chrome Base. The prong (base) is made

of Chrome. The telescopic bellow is 3 piece telescopic type and injection molded in black polyurethane.

35 Gas lift : The chair is featured with Gas lift mechanism for Seat height adjustment. NOS. 32 11146.3095 356681.904

Arm rest : PU adjustable arm rest.

Castors : fitted with 5 nos. twin wheel nylon castors (castor wheel dia 50mm).

DISCUSSION TABLE

Discussion Table

Table top to be made in 25 mm Prelaminated partical board. All exposed edges sealed with 2 mm thick pvc edge banding tape.

understructure in chrome base. NOS. 14 10121.3615 141699.061

37 VISITOR SOFA SEATING -Two Seater Sofa In Select Fabric WOOD Legs. Solid WOOD & Plywood Inner Structure-1520*880*790*440 NOS. 4 28826.6625 115306.65

Top:- Storage Top made of 25 mm thick post formed prelaminated partical board,all exposed edges sealed with 2 mm thick pvc edge

38 Understructure :- storage understructure shall be made of 18mm thick prelaminated partical board.Storage having openable shutter

with locking arrangement .

Shelf :- Storage shelf made of 18 mm thick prelaminated partical board.

ii 3600(l)x450(D)x1200(Ht) - PLANTER STORAGE NOS. 2 49197.504 98395.008

OFFICE ASST. WRK DESK AREA

RUNNING WORKSTATION with overhead storage as per site allowances

Table :- 2800x600x750ht ( LENGTH AS PER SITE ALLOWANCES ) incl of OVERHEAD STORAGE 2800L X 350 D X 450 HT WITH SHUTTERS -

Made in 18 mm Prelaminated partical board. All exposed edges sealed with 2 mm thick pvc edge banding tape.

Table :- 3600x600x750ht ( LENGTH AS PER SITE ALLOWANCES ) incl of OVERHEAD STORAGE 3600L X 350 D X 450 HT WITH SHUTTERS :-

Made in 18 mm Prelaminated partical board. All exposed edges sealed with 2 mm thick pvc edge banding tape.

Medium back Asst. chair : Seat is made out of 9 layer 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-

nuts and revited in to the wood.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair

Standards.Back Frame is upholstered with Thinner Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support position

for good back support and blood circulation.Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long

41 life.The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile strength. NOS. 7 9608.8875 67262.2125

Springs are made out of Grade II material.Fixed steel base of 25mm dia pipe of 1.5 mm thickness with Chrome with PVC shoes.Chair

dimensions should be Width- 63.5 cm ,Depth- 57 cm , Height- 86 cm,Width (Arm to Arm)- 46 cm ,Seat Depth- 49 cm Width- 49.5 cm.

STAFF MEETING ROOM

TABLE FOR STAFF MEETING AND HUDDLE ROOM

SIZE- 2100W X 900D X 750HT

Specifications:

Table top - The work surface will be in veener 25mm thick one side . confirming to IS-14587:1998. The density of veener will be

680kg/m³. Surface: CPL( continuous pressure laminate) in 0.5mm thickness in veener finish. The veener will be confirming to E-1 Grade

as per the JIS A 5905-2003 standards and approved shade confirming to IS-12823:1990.PVC edge band will be minimum 2 mm thick,

will be imported, quality confirming to DIN 68861, 53388 standards. The edge band will be fixed to the work surface edges all round

with Imported Hot melt Glue confirming to ISO 9001- 2008 and certified by ANSI for quality.

Under Structure - • The MS supports are made of 50 x50mm square ERW tubes- 16g with levelers to cater for floor undulations- +/- 20

mm. ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members will be connected through a horizontal member size 1.6mm thk,

42 50x25 cold formed ERW tube confirming to IS 4923: 1997. The vertical and the horizontal tubes will be welded with CO2 MIG welding NOS. 3 24214.3965 72643.1895

process confirming to IS 816 and ISO 9692-2. The leg will be fabricated using Argon & Co2 gas mixture on a Robotic welding machine to

ensure adequate welding strength with consistency.• The legs will be connected with Cross beams to take care of the bending stress

catering.• The number of cross beams will be based on the depth of the table. The Cross Beams are made of 40x20 mm ERW tubes- 16

Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.Cable Trays will be provided when the

cable access is required from the top through ‘Flip ups”. The Switch/socket slots are provided as a part of the “Flip Up” design just below

the flip covers. The “flip up” should be made in aluminum flip covers with soft closing arrangement. The “Flip up” cover will be anodized

in Silver grey finish to 20 microns confirming to IS 1868:1996, EN—2373-1 and IS 2360.

Medium back Visitor chair : Seat is made out of 9 layer 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-

nuts and revited in to the wood.Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair

Standards.Back Frame is upholstered with Thinner Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support position

for good back support and blood circulation.Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long

life.The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile strength.

43 Springs are made out of Grade II material.Fixed steel base of 25mm dia pipe of 1.5 mm thickness with Chrome with PVC shoes.Chair NOS. 15 9608.8875 144133.3125

dimensions should be Width- 63.5 cm ,Depth- 57 cm , Height- 86 cm,Width (Arm to Arm)- 46 cm ,Seat Depth- 49 cm Width- 49.5 cm.

EXECUTIVE & STAFF DINING AREA FURNITURE

TABLE FOR EXECUTIVE DINING ROOM

SIZE- 1350X1350 X 750HT

Specifications:

Table top - The work surface will be in cross grain matched veener 4mm thick over 25 mm MDF base both sides . confirming to IS-

44 14587:1998. The density of veener will be 680kmm g/m³. Surface: CPL( continuous pressure laminate) in 0.5mm thickness in veener NOS. 4 61496.88 245987.52

finish. The veener will be confirming to E-1 Grade as per the JIS A 5905-2003 standards and approved shade confirming to IS-

12823:1990. . Edges to be finsihed in matching veneer/ wood edge band as per design

Under Structure - • in 18 mm MDF box 600 x 600 supporting top and f/inished in veneer and polish to match table top

CHAIR FOR EXECUITVE DINING AREA

Chair:- Leatherette upholsted chair with cushioned seat & back with wooden structure and wooden legs.

Side Serving Storages :- 7000x500x750 ht storage :- Storage Top made up of 19 mm thick with mdf board with Veneer finish.

46 Understructure :- Storage carcass & shutter is 19 mm thick mdf board with veneer duly finish.Storage have openable shutter with NOS. 1 192177.75 192177.75

locking arrangement & 19 mm thk.shelf in mdf. top to be in Solid Acrylic surface 18 mm thk with edge profile moulding as per design

TABLE FOR STAFF DINING- FOLDABLE

Table for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Edge banding (PVC)

2mm.E1 grade 1mm laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-

house quality. This should comply with (EN 120-1992).The understructure is made of Steel pipe dimension40-50mm dia . Thickness

2.5mm. Epoxy powder coated spray paint, baked at temperature 200 C° coated of 50-60 micron thickness.Table sould have Green

Guard certificate and BIFMA certified.

Chair Back : The back of the chair is wooden with fabric upholestry.

48 Chair Seat : The Seat of the chair is upholstered with wooden & fabric Cushioned. The chair shall have deep cushioned in seat comfort NOS. 18 14733.6275 265205.295

to body contours for proper alignment, posture and all day comfort.

Frame:- Chair have PROFILED wooden frame.-WITH STACKABLE DESIGN

Providing and supplying corner table having dimension 600mm dia laminate top- Prelam partcle board with 2 mm edge banding finishes

, height 400mm and base plate dia 475mm .Table has Chrome Finishes

RECEPTION & LONGE AREA SEATS : Seating is made of Moulded PU foam and is upholstered with leatherite / fabric as per client. The

moulded PU structure has embeded arrangement for fixing the understructure . The understructure has metal chrome plated base plate

for joining with PU Structure .

VIP LOUNGE ARE CHAIRS Chair Back & Seat : The back & Seat of the chair is upholstered with CHOICE

SELECT Fabric WITH 3M FABRIC GUARD. and cut foam on 12mm thick BWP Plywood. The chair shall have deep cushioned in seat

comfort to body contours for proper alignment, posture and all day comfort.

Base : The chair is featured with Aluminium Base.

VIP LOUNGE ARE CHAIRS Providing and supplying corner table having dimension 600mm dia laminate top- Prelam partcle board with

2 mm edge banding finishes , height 400mm and base plate dia 475mm .Table has Chrome Finishes

HIGH TABLE 3600X450X1050 MM :- TOP 25 MM Thick MDF & BASE - 40X40 MM LOOP LEG WITH CRCA PIPE WITH DULY POWDER

COATED FINISHES.

HIGH CHAIRS at OPEN PANTRY @WOODEN LEGS & DESIGNER UPHOLSTERY

HI stool of the follwing specifications. Providing and placing in position stool.The SEAT ASSEMBLY:Seat is leatherette upholstered

cushion fitted to a seat tray. The cushion is made of 1.2 cm of PU slabstockfoam.Slabstock foam glued to CRCA sheet of 0.12 cm

(±0.01cm) thick and upholstered with leatherette.The seat tray l5 made of CRCA steel of 0.25 cm thk (±0.01cm) as per IS:513.

It is powder coated with epoxy based polyster powder coating (40-60 microns).

* SEAT CUSHION SIZE : 40.0 cm. (W) x 34.5 cm. (D)

* TOP TRAY SIZE: 41.5 cm. (W) x40.0 cm. (D)

54 WOODEN UNDERSTRUCTURE:Understructure of bar stool is made of FSC-certified seasoned teak wood finished with a clear matt coat NOS. 5 10121.3615 50606.8075

of PU lacquer.Thei size of UNDERSTRUCTURE : 48.6 cm (W) x 47.0 cm (D) x 6.88 cm (H)

FOOT REST ASSEMBLY :Foot rest is made up of 01.6 cm (±0.02 cm) M.S. ERW tube (IS:71380). It is epoxy based powder coating (40-60

microns).Additionally it is coated with abrasion resistance coating.* FOOT REST SIZE : 40.3 cm (W) x 38.7 cm (0).

COMPACTOR STORAGES :

COMPACTOR (Without Shutter) Mechanical drive

The KNOCK DOWN STORAGE UNITS shall be powder coated with epoxy polyester powder with approximately overall height of

2080mm.. Each unit . The body of the module shall be 0.8 mm thick CRCA steel The unit shall be divided into five loading compartments

by placing four shelves of .8 mm thick CRCA steel. The unit or row of units shall rest on understructure of approximate height 65 mm

made up of 3.15 mm thick hot rolled steel sheet which in turn shall rest on set of rails 35 mm high consisting 'J'section 2 mm thick hot

rolled sheet and 25 mm square bar, both connected by screws.The rails shall be embedded to properly levelled ground with the help of

rawl plug and screw. The configuration shall consist of one single static unit of depth 457 mm, twin mobile drive units of depth 915 mm

as required and one last drive of depth' 457 mm. The cost will include all necessary fittings, locks, bolts, screws, painting, powder

coating and rails complete and nothing extra shall be paid on this account.

SFF-C 4(Single Face Fixed Unit) NOS.

DFM-C4 (Double Face Mobile Unit) NOS.

SFM-C4 (Single Face Mobile Unit) NOS.

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE

B , TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE BLOCK 1 , NEW DELHI

Indicative Commercial

HORTICULTURE & LANDSCAPING

S.no. DSR NO. Description Qty Unit Price per piece/sq.ft Net Total

4 Terrace Green Wall : Structural MS work riveted,

bolted & welded in built up sections, trusses & framed

work, including cutting, hoisting, fixing in position &

applying a primimg coat & painting with synthetic enamel

paint all complete. 4 walls including Installation &

Labour + MS Frame Work for Vertical Garden

2 MR Song Of India Variegata - Indoor/Ornamental Plants 20 no. INR 666.22 INR 13,324.32

Rectangular Tray Acrlic Planters

Plant : Epipremnum aureum

Self Watering Tray Top Planters

Plants : Ficus Bonsai

Bryophyta Wall (Moss) on the outer elevation of

7.00 Each INR 341.00

Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10

6 10027 suckers, well developed,fresh and healthy with lush 2387.00

green foliage in 30 cm size of Earthen pot /Plastic pot

8 Each INR 345.00

Rhapis Palm having ht. 75 cm to 90 cm with 15 to 18

7 10080 equal suckers, welldeveloped, full of fresh and healthy 2760.00

leaves from bottom to top in 35 cm PVCPots/C.Pots

Money Plant Golden leaves mounted on moss stick 12.00 Each INR 180.00

90cm ht., having 3plants at equal distance, well

8 10064 developed with full of fresh, shinning andhealthy leaves 2160.00

from bottom to top in 25 cm size of Earthen pot /

Phoenix Palm having ht. 75 cm to 90 cm with 10 to 15 or 7.00 Each INR 210.00

9 10077 more leaves, welldeveloped, fresh and healthy in 25 cm 1470.00

size of Earthen pot / Plastic pot

Supply & installing Stainless Steel PLASTIC Pots of

approved colour shades of medium size. (Colour, size,

shape as per Engineer-in-charge's choice)

TOTAL INR 218,267.72

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE B , TOWER 1 , EAST KIDWAI NAGAR, NBCC

OFFICE BLOCK 1 , NEW DELHI

Sr. No. 2018 Item Description Unit QTY. NDSR N DSR AMOUNT

INTERNAL ELECTRICAL WORK

WIRING & SUBMAIN

1 1.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

2 1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (

without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc. as required.

3 MR Wiring for the MCB controlled Primary light points with 2.5 sq.mm PVC insulated copper Each 24 1097.00 26328.00

conductor 1100 volts grade stranded flexible FRLS wires of approved make in concealed or

surface mounted 25 mm dia 2.0 mm thick PVC conduit but controlled by existing MCB

provided in D.B. including earthing of fixtures with 2.5 sq.mm insulated copper wire.

4 1.13 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single Metre 900 308 277200

core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4 sq. mm FRLS

PVC insulated copper conductor single core cable for loop earthing as required.

5 1.14 Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC

insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 4000 167 668000

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 1000 200 200000

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 249 12450

1.14.9 4 x 6 sq.mm + 2 x 6 sq.mm. earth wire Metre 200 394 78800

1.14.10 4 x 10 sq.mm + 2 x 6 sq.mm. earth wire Metre 100 543 54300

1.14.11 4 x 16 sq.mm + 2 x 6 sq.mm. earth wire Metre 120 752 90240

6 1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

1.24.1 5/6 amps switch EACH 300 85 25500

1.24.4 3 pin 5/6 amp socket outlet EACH 180 111 19980

1.24.5 6 pin 15/16 amp socket outlet EACH 80 175 14000

1.24.6 Telephone socket outlet EACH 130 119 15470

1.24.7 TV socket outlet EACH 20 119 2380

1.24.8 Bell Push EACH 10 126 1260

7 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box EACH 33 32 1056

excluding modular plate as required.

8 1.27 Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

9 1.35 Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED

lamps per fitting, complete with all accessories including

connections etc. as required.

10 1.5 Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing, commissioning

etc. as required.

1.50.1 Upto 450 mm sweep EACH 3 363 1089

11 1.51 Extra for fixing the louvers/ shutters complete with frame for a EACH 3 168 504

exhaust fan of all sizes.

12 2.18 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and Each 2 1232 2464

earth, metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel

enclosure, on surface or in recess, with chained metal cover for the socket out let and

complete with connections, testing and commissioning etc. as required.

13 2.16 Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 Each 2 848 1696

volts “C” curve DP MCB complete with connections, testing and commissioning etc. as

14 2.19 Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and Each 3 1690 5070

earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure,

on surface or in recess, with chained metal cover for the socket out let and complete with

2.17 connections,

Supplying andtesting

fixing and commissioning

TP sheet etc. asonrequired

steel enclosure surface/ recess along with 16/25/32 A 415 V

15.0 "C" curve TP MCB complete with connections, testing and commissioning etc. as required Each 2 1146 2292

16 7.1 Laying of one number PVC insulated and PVC sheathed / XLPE

power cable of 1.1 KV grade of following size direct in ground

including excavation, sand cushioning, protective covering and

refilling the trench etc as required.

7.1.2 Above 35 sq. mm and upto 95 sq. mm m 100 338 33800

17 MR Providing and fixing of 1 No.13 amp modular type 3 pin international live socket, cover plate, 5 NO. 30 180.00 5400.00

sided G.I. Boxes for housing switches and sockets and earthing complete as required .

18 MR Providing and fixing of 1 No. 16 amps switch with indicator, cover plate, 5 sided G.I. Boxes Set 20 288.00 5760.00

for housing switches and sockets and earthing complete as required .

19 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

surface/recess including cutting the wall and making good the same in case of recessed

conduit as required.

1.21.2 25mm dia PVC conduit Metre 1700 90 153000

1.21.3 32mm dia PVC conduit Metre 400 92 36800

DISTRIBUTION BOARD

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution

board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth

bar, din bar, interconnections, powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

2.3.3 12 way , Double door Nos. 1 2,053 2,053

Supplying and fixing following way prewired vertical type TP&N MCB distribution board of steel

sheet for 415 volts on surface/ recess complete with loose wire box of sheet steel, dust

protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCB's, terminal connectors for all incoming and outgoing

circuits, duly prewired with adequate size of FR PVC insulated copper conductor upto the

terminal connector/ neutral link, earthing etc as required (But without MCB/ RCCB/ Isolator).

(Note : Prewired vertical type MCB TPDB is normally used where 3 phase outlets are

Supplying and fixing following rating, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

22 2.15 having a sensitivity current 30 mA in the existing MCB DB

complete with connections, testing and commissioning etc. as

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker

23 2.10 suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

2.10.1 Single pole Nos. 194 199 38,606

2.10.3 Double Pole Nos. 20 556 11,120

Supplying and fixing single pole blanking plate in the existing

MCB DB complete etc. as required. Nos. 8 240

LIGHTING FIXTURE & FAN

Supply, Erection, Testing & Commissioning Surface/suspended Round Direct LED luminiare

of 600mm dia approx & 60-80 mm thickness approx , made of high-grade aluminium housing

in color/as per architects choice. Screwless and seamless circumference and extremely

1 MR smooth homogeneous light through the diffuser. System power min 30 W & 3000 lumens, Each 3 24189.19 72567.57

230V, CRI>80, , Color temperature- 4000/5700K , Power factor>0.95, surge protection of

3.5KV, THD<10%. Operating voltage range 230V AC suitable for 50 Hz frequency. or its

Supply, Erection, Testing & Commissioning Surface/suspended Round Direct LED luminiare

of 900 dia approx & 60-80 mm thickness approx , made of high-grade aluminium housing in

color/as per architects choice. Screwless and seamless circumference and extremely smooth

2 MR homogeneous light through the diffuser. System power min 40 W & 3000 lumens, 230V, Each 10 29794.27 297942.73

CRI>80, , Color temperature- 4000/5700K , Power factor>0.95, surge protection of 3.5KV,

THD<10%. Operating voltage range 230V AC suitable for 50 Hz frequency. or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Suspended LED, Body made of

Aluminium and Diffuser with homogeneous light distribution System power , 20W, 230V,

1200mm Led Color 4000/5700K. Power factor>0.95, surge protection of 3.5KV, THD<10%.

Minimum lumens output 2000 lumens. Operating voltage range 230V AC suitable for 50 Hz

frequency are to be supplied with connectors for corner bends . or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Suspended LED Channel, Body

made of Aluminium and PMMA Diffuser with homogeneous light distribution and without

hotspots, System power , 20W, 230V, 900mm Led Color 4000/5700K. Power factor>0.95,

surge protection of 3.5KV, THD<10%. Minimum lumens output 1500 lumens. Operating

voltage range 230V AC suitable for 50 Hz frequency are to be supplied with connectors for

corner bends . or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Suspended LED Channel, Body

made of Aluminium and PMMA Diffuser with homogeneous light distribution and without

hotspots, System power , 40W, 230V, 2400mm X 50mm X 85mm, Led Color 4000/5700K.

Power factor>0.95, surge protection of 3.5KV, THD<10%. Minimum lumens output 4000

lumens. Operating voltage range 230V AC suitable for 50 Hz frequency. To be supplied with

connectors for corner bends or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Suspended LED Channel, Body

made of Aluminium and PMMA Diffuser with homogeneous light distribution and without

hotspots, System power , 10W, 230V, 600mm Led Color 4000/5700K. Power factor>0.95,

surge protection of 3.5KV, THD<10%. Minimum lumens output 1000 lumens. Operating

voltage range 230V AC suitable for 50 Hz frequency.. To be supplied with connectors for

corner bends or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Recessed LED Channel, Body

made of Aluminium and PMMA Diffuser with homogeneous light distribution and without

hotspots, System power , 20W, 230V, 1200mm , Led Color 4000/5700K. Power factor>0.95,

surge protection of 3.5KV, THD<10%. Minimum lumens output 2000 lumens. Operating

voltage range 230V AC suitable for 50 Hz frequency. To be supplied with connectors for

corner bends or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Recessed LED Channel, Body

made of Aluminium and PMMA Diffuser with homogeneous light distribution and without

hotspots, System power , 14W, 230V, 900mm Led Color 4000/5700K. Power factor>0.95,

surge protection of 3.5KV, THD<10%. Minimum lumens output 1400 lumens. Operating

voltage range 230V AC suitable for 50 Hz frequency. To be supplied with connectors for

corner bends or its Equivalent

Supply, Erection, Testing & Commissioning of High Efficiency Recessed LED Channel, Body

made of Aluminium and PMMA Diffuser with homogeneous light distribution and without

hotspots, System power 40W, 230V with CRI>80, 2400mm Led Color 4000K. Power

factor>0.95, surge protection of 3.5KV, THD<10%. Minimum lumens output 4000 lumens.

Operating voltage range 150-270V AC suitable for 50 Hz frequency. or its Equivalent

Supply, Erection, Testing & Commissioning of SUSPENDED Linear Direct/indirect LED

luminiare, Body made of high-grade Aluminium housing in powder coating Screwless and

Seamless finish with transparent microprismatic diffuser and power through suspension cable,

40W, with CRI>80, Fixture length 1100-1200mm x Thickness 6-8mm x width 200-220mm.

Color temperature 4000/5700K. Power factor>0.95, surge protection of 3.5KV, THD<10%.

Minimum lumens output 3000. operating voltage range 230V AC suitable for 50 Hz frequency.

Power should be thrpough suspension cable. or its Equivalent

Supply, Erection, Testing & Commissioning High Efficiency Suspended LED linear soft

formations with curved joinings, Body made of Aluminium and PMMA Diffuser with

homogeneous light distribution and without hotspots, System power , 30W per meter, 230V,

50mm width, Led Color 4000/5700K. Power factor>0.95, surge protection of 3.5KV,

THD<10%. Minimum lumens output 100 lumens per watt. Operating voltage range 230V AC

suitable for 50 Hz frequency. or its Equivalent

Supply, Erection, Testing & Commissioning decorative round fixture of dia 210mm and height

400 mm , made of high-grade aluminium housing in color/as per architects choice. Screwless

and seamless circumference and extremely smooth homogeneous light through the frosted

12 MR unbreakable polycarbonate diffuser, without hot spots. System power 25W & 2300 lumens, Each 8 9259.57 74076.57

230V, CRI>80, , Color temperature- 4000/5700K , ,IN Power factor>0.95, surge protection of

3.5KV, THD<10%. Operating voltage range 230V AC suitable for 50 Hz frequency. or its

Supply, Erection, Testing & Commissioning Surface/suspended Traiangular Direct LED

luminiare 450mm x 450mm x 450mm, made of high-grade aluminium housing in color/as per

architects choice. Screwless and seamless circumference and extremely smooth

13 MR homogeneous light through the frosted unbreakable polycarbonate diffuser, without hot spots. Each 6 17441.87 104651.24

System power 25-35 W & min 2000 lumens, 230V, CRI>80, , Color temperature- 4000/5700K

, Power factor>0.95, surge protection of 3.5KV, THD<10%. Operating voltage range 230V AC

suitable for 50 Hz frequency. or its Equivalent

Supply, Erection, Testing & Commissioning of Recessed High Efficiency LED Round

Downlight, Body made of Aluminium and PC/PMMA Diffuser with homogeneous light

distribution and without hotspots, System power 15W approx & min 1200 lumens, 230V with

CRI>80, , Led Color 4000/5700K. Power factor>0.95, surge protection of 3.5KV, THD<10%.

Operating voltage range 230V AC suitable for 50 Hz frequency. or its Equivalent

Supply, Erection, Testing & Commissioning of Recessed High Efficiency LED Recessed High

Efficency 2X2 LED Grid light, Body made of CRCA or any other material and Opal Diffuser

with homogeneous light distribution without hotspots. System power min 25W and 2800

lumens, 230V with CRI>80, , Led Color 4000/5700K. Power factor>0.95, surge protection of

3.5KV, THD<10%. Operating voltage range 150-270V AC suitable for 50 Hz frequency. or its

16 Supplying, fixing, connecting, testing and commissioning of LED flexible strip cove light for

MR white color including all drivers, connecting cables, controllers , non dimmable, average 5-6 Meter 410 541.10 221851.42

watt / metre. Color as per instruction complete as required

Decorative LIGHTING

Supply, Erection, Testing & Commissioning of decorative floor lamp in Structure made of a

metal frame and a circular base coated with epoxy powders, on which a lampshade covered

with fabric or alabaster is mounted. 1 x max 20W - 220-240V Ø 52 H. 150 cm or its Equivalent

Supply, Erection, Testing & Commissioning of decorative table lamp in Structure made of a

metal frame and a circular base coated with epoxy powders, on which a lampshade covered

with fabric or alabaster is mounted. 1 x max 10W - 220-240V Ø 24 H. 50 cm or its Equivalent

Supply, Erection, Testing & Commissioning of wall light made in metal with chrome and light

gold finish and craved crystal diffuser. Diameter: 13 cm

Height: 38 cm Thickness: 18 cm LIGHT BULBS Lumen: 600 Led: 1X7w Driver:Included

Voltage: 230V or its Equivalent

Supply, Erection, Testing & Commissioning of wall light made in metal with chrome and light

4 MR gold finish and craved crystal diffuser. LIGHT BULBS , Driver: Included Voltage: 230V or its Each 4 19715.81 78863.26

Supply of 9 W mirror light with high efficient LED’s,CRI >70, Lumens ≥900, , Driver shall be of

constant current type, operating temperature from -10 to +45 degree celcius, power

5 MR factor>0.90, rated voltage 220-240V AC working range:- 140-270 V A'c , 50 Hz +_ 5%, AC Each 5 835.95 4179.73

supply. Complete in all respect with the entire satisfaction of Engineer-in-Charge. or its

Supplying of Plastic Body Ornamental Exhaust Fan heavy duty 230V A.C 50 cycles, 300 mm

6 MR sweep, 1300 rpm, energy efficient, complete erected in position with all accessories or its Each 2 1576.35 3152.71

Supplying,installation,testing and commissioning of Passive Infrared(PIR) technology based

occupancy sensor having high preformance, non regulating programmable type, suitable for

7 DSR-15.1 connected load upto 10Amp , for mounting height up to 2.8 mtr and for 5 m diameter coverage Each 25 4538 113450

area along with necessary fixing arrangements i/c programming at site etc. complete as

required or its Equivalent

Supplying, installation, testing and commissioning of (N+1) 40 kVA online double conversion

fully microprocessor based ,indoor type, compact UPS system of mentioned rating with

designed output PF 1 at 40 degree and IGBT based PWM technology with external Isolation

transformer to achieve THD < 5% and input power factor of greater than 0.95 at 50% loading,

Efficiency >= 93% at 50 % load, suitable for three phase AC input voltage 320 V to 480 V, 50

Hz +3% / - 3 % and three phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz

with all components as mentioned in BOQ, specifications and schedule, complete as required

and as per technical specification. Each unit shall be comprising of the following: Total 2 no.s

125% rated Rectifier cum charger unit +100% rated Invertor, Integrated in UPS module

100% rated Inbuilt static switch at the invertor output + 2 Nos. 100% rated Inbuilt static

switches at the static bypass line.

c 100% rated Inbuilt Maintenance Bypass.

Web-enabled Monitoring and Management through SNMP protocols for multi-OS

e Inbuilt feature required for input phase seq protection and automatic change. UPS should

work on mains and should not go to battery mode in case of input phase sequence change.

Supplying, unloading, installing testing and commissioning of necessary VRLA batteries of

suitable size having 30 minutes back up time to 40 KVA UPS for full load to be provided. 1

f No spare batteryof same AH to be provided and cost to be added.

Note : Concerning vendor needs to furnish the battery sizing calculations at the time of

GA approval and battery size has to be as per the approved GA drawing.

Supply, unloading, installation testing & commissioning of matching cabinet/open racks to

house above mentioned batteries for 40 KVA UPS system along with suitable size

interconnecting cable (for UPS to Battery and battery to battery), MCCB etc. complete as

required & as per specifications.

Supply,installation testing and commissioning of UPS monitoring software suitable for RJ-45

h communication and capable of giving pop up messages for all alarms received from UPS. All

shall be capable of the following:-

Giving notifications like e-mail, paging notification, broadcast notification, battery

replacement notification, run event-based scripts.

Event logging, data logging and action logging (with date, time, description of fault and

k Run the battery diagnostic test.

l Automated unattended shutdown of computers.

m Local notification through audible alarm.

Software should support :

n latest version of Microsoft Windows/ Server, AIX, HP-UX, Sun Solaris, Linux, Novell

o SITC of External Isolation transformer

RACEWAYS AND CABLE TRAYS

supplying installation of raceway on ceiling/ surface minimum 1.6 mm thick GI having powder

coated with openable cover, totally enclosed, the joints between two lengths of channels or

between channel and junction box shall be joined together with 3 mm thick M.S. Powder

coated coupler plates to make it dust and water proof. The cost shall including all supporting

and fixing accessories including dash fasteners. ( Orange colour for data and Blue colour for

power) or its equivalent

MR 225-300 mm (wide) x min 30 mm (height) 3 compartment Metre 100 1114.09 111409.02

MR 150-225 mm (wide) x min 30 mm (height) 3 compartment Metre 150 843.00 126450.00

MR 75-150 mm (wide) x min 30 mm (height) Metre 200 636.00 127200.00

3 supplying installation, G.I. Junction boxes of required thickness for raceways cover

including providing neoprene gaskets between the cover and the junction box, cadmium

plated flat/round head screws, height as per site condition,totally enclosed. Proper cutouts

shall be made in the side walls for raceway entry wherever required. The junction box shall be

all side walls should be welded expect top cover and all side walls shall have suitable size of

rectangular knock out holes for taking raceways / conduits as required and not a complete cut

out. The top cover should be sealed with M Seal to make it dust and water proof complete as

MR required etc. or its equivalent

CABLE & END TERMINATIONS

4.0 9.1 Supplying and making end termination with brass compression gland and aluminium lugs for

following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

5.0 MR SITC following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor/copper

conductor power/ multicore control armoured cable of 1.1 KV grade.

MR 3 ½ C-70 sq mm Aluminium (For Main Panel) Metre 50 347.21 17360.62

MR 4C- 25 sq mm Aluminium (For UPS Panel) Metre 50 278.00 13900.00

MR 4C- 16 sq mm Aluminium Metre 20 196.00 3920.00

MR 4C- 10 sq mm Aluminium (For AHUs) Metre 400 164.00 65600.00

MR 3C- 10 sq mm Aluminium Metre 5 139.00 695.00

MR 3C- 6 sq mm Aluminium Metre 10 97.00 970.00

MR 1C X 25 Sqmm Copper flexible Cable (For UPS Connection) Metre 60 316.00 18960.00

DSR/MR CABLE TRAY

6.0 4.1 Supplying and installing following size of perforated painted with powder coating M.S.

cable trays with perforation not more than 17.5%, in convenient sections, joined with

connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting

suspenders etc as required.

4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Metre 100 476 47600

4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Metre 100 531 53100

DSR/MR EARTHING

5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and Set 3 6216 18648

7 providing masonry enclosure with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and Set 1 11794 11794

providing masonry enclosure with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth Metre 10 853 8530

electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required.

(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer

spaced at 50mm)

5.9 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth Metre 5 131 655

electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.

(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced

5.1 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode Metre 10 1224 12240

11 including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as

5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode Metre 5 483 2415

12 including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as

5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. Metre 300 57 17100

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. Metre 180 1009 181620

5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as Metre 180 206 37080

DISTRIBUTION PANEL

MR FRONT OPERATED PANEL

16 Design, manufacture, supplying fixing in position of the following front operated cubicle

type,compartmentalised with front access, dead back, 2mm thick steel enclosed free standing,

dust and vermin proof, switchboard with IP42 protection with hinged and lockable doors

complete with interconnections, tinned copper crimping lugs, bonding to earth and painting,

suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable for a fault level of

25 KA symmetrical at 415 volts.

i All switchboards shall be modular type and have provision for entry of cables from the top

/bottom as required.

ii The cost shall include providing and fixing of channels for switchboard support.

iii All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The

Busbars insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar

supports shall be used.

iv All MCCB shall have phase barriers, rotary handles and extension terminal as required .

MAIN BUILDING PANEL

1 Nos. 125A, 4P, MCCB (25kA) with O/C, E/F, S/C release..

B Metering & Indication:

i) 1 set of R,Y,B phase indicating lamps

ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

iii) 1 No. (0-125A) Ammeter with ASS with 3 nos. 125/5A CT's

iv) 1 No. Digital Electronic KWH meter(Dual Source).

200 A, 4P Aluminium , colour coded insulated bus bars suitable for 415V, 50Hz AC Supply.

Outgoing Section :

6 Nos. 40 A,4P MCB (10kA) For AHUs.

1 No. 63 A,4P MCB (10kA) For Power DB.

1 No. 40 A,4P MCB (10kA) For power DB.

2 No. 40 A,4P MCB (10kA) For Lighting DB.

2 Nos. 100 A,4P MCCB (25kA) For UPS.

4 Nos. 40 A,4P MCB (10kA) Spare

1 No. 63 A,4P MCB (10kA) Spare

MAIN BUILDING PANEL described above Each 1 275992.80 275992.80

17 MR UPS PANEL

2 Nos.100A, 4P, MCCB (25kA) .

B Metering & Indication for each incomer :

i) 1 set of R,Y,B phase indicating lamps

ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

iii) 1 No. (0-100A) Ammeter with ASS with 3 nos. 80/5A CT's

iv) 1 No. Digital Electronic KWH meter(Dual Source).

100 A, 4P Copper , colour coded insulated bus bars suitable for 415V, 50Hz AC Supply.

i) 2 No. 63 A,4P MCB (10kA)

ii) 2 Nos. 25 A,DP MCB (10kA)

iii) 2 No. 40 A,4P MCB (10kA)

UPS PANEL described above Each 1 107649.00 107649.00

MCCB with encloser box FOR UPS Connection

18 MR Supply, installation, testing & commissioning of 100 amps 4P MCCB(25 KA) with thermal

Magnetic release (PRMB-3) with Class-C transient voltage surge suppression device suitable

for 3 phases as per specifications. The MCCB shall be provided with 2mm thick steel enclosed Each 2 9046.00 18092.00

free standing, dust and vermin proof, encloser with suitable protection with hinged and

lockable doors complete with interconnections.

MR FIRE SUPPRESSION SYSTEM

SITC of FIRE SUPRESSION SYSTEM having cyclinder of sufficient capacity (Including FIRE

MR AGENT ) , Hose , Actuator , Gas release Module , Switch , Hooter etc complete in all respects Nos. 1 742461.02 742461.02

19 as per the direction of Architect /or Engineer In charge.

TOTAL of DSR & MR heads 2750875.00 6709477.67

Grand Total 9460352.67

Grand Total 9460352.67

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE B , TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE

BLOCK 1 , NEW DELHI

CPWD DSR Description DSR DSR

Sr. No. Unit QTY. NDSR N DSR AMOUNT

2018 Item no RATE AMOUNT

TV, DATA, VOICE NETWORKING

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed

Steel/ PVC conduit as required.

1.53.1 1 run of cable Metre 10260 49 502740

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

2 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the MTR 600 33.00 19800.00

exisitng surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes of medium class PVC conduit along with accessories

3 1.21 in surface/recess including cutting the wall and making good the same in case of recessed

conduit as required.

Supplying, installing, testing and commissioning of CAT 6 UTP Jack PCB based

Information Outlet (I/O) RJ45,confirming to following standards Category-6A. UL Listed,

ETL Channel test report as per ISO/IEC 11801, ANSI/TIA 568 C.2,Current Rating: 1.5 A

(max), must support 90-degree cable termination. Plug Retention Force: 133 N minimum

between modular plug and jack, Meets and exceeds ISO 9001:2015, RoHS compliant or its

Supplying, installing, testing and commissioning of Cat 6 U/UTP loaded Jack Panel should

be UL Listed, RoHS Compliance, Current Rating” 1.5A @20ºC or 68ºF, Insulation

5 MR Resistance Min. - 500 M Ohm. The patch panel type shall be a 1U panel capable of Nos. 10 6234 62342.42

supporting 24 unshielded modular 8-pin connectors compliant with IEC 60603-7 while

meeting the Channel Performance. or its equivalent

Supply, Installation, Testing and Commissioning of Twenty four (24) 10/100/1000Mbps

RJ45 ports and should have Four (4) 1G SFP+ Slots, support Stacking up to 8 Switches

with more than 10 Gbps stacking bandwidth per Switch, Non-Blocking switch fabric capacity

of 128 Gbps or more, Should provide wire-speed packet forwarding of 95 Mpps or more,

support 4K active VLANs, support 16K MAC addresses or more, support IP multicast

snooping IGMP v1, v2, v3, support Jumbo Frames (up to 9K bytes), Layer 3 features like

RIP, RIPng, OSPF, PBR and VRRP from day 1, support minimum support minimum 1K

6 MR IPv4 routes and 1K IPv6 route, support RADIUS, TACACS/TACACS+ and Nos. 18 120343 2166173.79

username/password for Authentication, Authorization and Accounting (AAA) with Local User

Accounts and Local User Passwords, Switch should have minimum 1GB of Main Memory

and minimum 2GB Flash Memory, with all necessary transreceiver and Switch OS from

same OEM, Product should be complied as per technical specification and along with 3

years OEM ON SITE Hardware warranty along with OEM web based / telephonic technical

Support. or its equivalent

Supplying & Fixing of Category 6,Cat 6 U/UTP Patch Cable, TIA- 568C Category-6, UL-

listed / ETL Channel test report as per ISO/IEC 11801, ANSI/TIA 568 C.2, RoHS

Compliant.Patch cords sheath shall be LSZH as per IEC 60332-1, IEC 60754-2, IEC 61034-

2, Operational Temp: -20º to 60º Celsius. Length 1.0 Mtr or its equivalent

Supplying & Fixing of Category 6,Cat 6 U/UTP Patch Cable, TIA- 568C Category-6, UL-

listed / ETL Channel test report as per ISO/IEC 11801, ANSI/TIA 568 C.2, RoHS

Compliant.Patch cords sheath shall be LSZH as per IEC 60332-1, IEC 60754-2, IEC 61034-

2, Operational Temp: -20º to 60º Celsius. Length 1.2 Mtr or its equivalent

Supplying, Installation, Testing & Commissioning of be Multimode (OM3), Single Jacket,

Corrugated Steel Tape Armor, Gel-free, Stranded Loose Tube Cable. Cable Fiber cable as

per ISO/IEC-11801/ANSI/TIA-568-C.3, Shall be able to meet Gigabit & 10 Gigabit Ethernet

performance up to 550 meters requirement specified by IEEE 802.3z (1000 Base-X) & IEEE

802.3ae (10G Base-X) Tensile load should be 2500 Newton or higher and crush resistance

should be 4000 Newton or higher ,The attenuation @ 850 nm should be ≤ 3.0 (Max) db/Km

and @ 1300 nm should be ≤ 1.5 (Max) dB/Km, the fiber construction can be unitube or

multitube, Gel-Free, but tensile and crush resistance parameters should be matched, the

jacket shall be MDPE. ROHS Complied.or its equivalent

Supplying & Fixing of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack

Mount ,Shall have all accessories including coupler plates pre loaded with 12 Nos. of LC

couplers (OM3) with all accessories complete in all respect.MM-OM3 , Fiber Pigtails should

comply to ANSI/TIA-568-C.3, Bend insestive fiber, LSZH Sheath as per IEC 60332-3, IEC

60754-2, IEC 61034-2, IEEE 383, UL 1666, UL 1685 or its equivalent

Supplying & Fixing of Fiber Optic Duplex Patch Cable (LC-LC), 3 Mtrs. Long, ISO/IEC-

11801-OM3 Duplex LSZH as per IEC 60332-3, IEC 60754-2, IEC 61034-2, UL 1666, All

patch cords shall conform to TIA-492AAAD , ANSI/TIA-568-C.3 , ANSI/ICEA S-83-596 and

11 MR Telcordia GR-409 and ISO/IEC-11801, Shall be Bend Insensitive, Duplex Multi Mode Fiber Nos. 4 3338 13352.52

Optic Patch Cords, MM-OM3 50/125 μm,Shall support network line speeds up to 10

Gbps.Shall have LC-LC Connector connectors at the ends complete in all respect or its

Supply & Fixing of OM3 Type Pigtails of ISO/IEC-11801-OM4 Pigtails with LC Type

Connectors,pigtails for terminating fibers on the FOPP complete in all respect. Pigtails

12 MR Should Complie to ANSI/TIA-568-C.3, ITU-G657.B-Bend insestive fiber,: IEC 60332-3, IEC Nos. 24 686 16464.00

60754-2, IEC 61034-2, IEEE 383, UL 1666, UL 1685 or its equivalent

Supply, Installation, Testing and Commissioning of Twelve (12) 10/100/1000Mbps RJ45

ports and should have two (2) 1G SFP+ Slots, support Stacking up to 12 Switches with

more than 10 Gbps stacking bandwidth per Switch, Non-Blocking switch fabric capacity of

64 Gbps or more, Should provide wire-speed packet forwarding of 41 Mpps or more,

support 4K active VLANs, support 16K MAC addresses or more, support IP multicast

snooping IGMP v1, v2, v3, support Jumbo Frames (up to 9K bytes), Layer 3 features like

RIP, RIPng, OSPF, PBR and VRRP from day 1, support minimum support minimum 1K

IPv4 routes and 1K IPv6 route, support RADIUS, TACACS/TACACS+ and

13 MR username/password for Authentication, Authorization and Accounting (AAA) with Local User Nos. 2 60804 121608.97

Accounts and Local User Passwords, Switch should have minimum 1GB of Main Memory

and minimum 2GB Flash Memory, with all necessary transreceiver and Switch OS from

same OEM, Product should be complied as per technical specification and along with 3

years OEM ONSITE Hardware warran warranty along with OEM web based / telephonic

technical Support. or its equival

Supplying Installation testing and Commissioning of SFP+ 10 Gigabit Ethernet Direct Attach

14 MR Copper (twinax copper cable) 1m in length complete in all respect. or its equivalent Nos. 6 8294 49764.00

Supplying Installation testing and Commissioning of 1000Base-SX Fiber SFP with Digital

Optical Monitoring, LC duplex connector, 850 nm, for distances up to 550 Meter , Multi

Mode Fiber, ROHS Compliant, Compliant with SFP Transceiver MSA specification,

15 MR Compliant with Specifications for IEEE 802.3z/Gigabit Ethernet, Compliant with Industry Nos. 4 11611 46444.00

Standard RFT Electrical Connector and Cage, Laser Class 1 Product which comply with the

requirements of IEC FDA 21CFR, 1040.10, Class 1 and CSA 60950-1-03/ UL 60950-1 or

Supplying & Fixing of Floor Standing Network/Server Rack - 42U / 800w / 800d, with Heavy

Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom

cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking.

Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side

Panels - 42U/800d Front MS Door Perforated honeycomb 42U/800w Rear MS Door Split

Perforated honeycomb 42U/800wFan 90CFM 230V AC, 4” dia Castors with Brake (set of 4)

Vertical Cable manager 80mmW 42U Shelf, Stationery 700mm N/W PDU 12Sockets

5/15Amps with MCB Mounting Hardware (Pkt. Of 20) earthing Kit 150mmH Cable manager

1U MS with Loops complete in all respect. or its equivalent

Supply fitting, fixing and testing of 9 U Wall mount rack of Width (mm)-600, Depth (mm) -

500, Approx.Net Wt (kg) - 20, CRCA 'D' Grade thickness (mm) - 1.2, Powder Colour for

Cabinet - RAL9002, Glass Toughened Tinted Glass Door, Accessories:, Fan & with all

required acessories. or its equivalent

Supply, installation, testing & Commissioning of 8(2X4) modules brushed brass/copper

18 MR colour pop-up boxes. All switch socket, DATA outlet, telephone etc are considered Nos. 10 4114 41140.00

separately or its equivalent

Supply, installation, testing & Commissioning of 1 module Female BNC 75 jack for pop up

box.or its equivalent or its equivalent

Supply, installation, testing & Commissioning of 2 Module Female HD15(VGA)for pop up

box. or its equivalent

Supply, installation, testing & Commissioning of 2 ModuleHDMI socket for pop up box or its

Supply, installation, testing & Commissioning of 1 Module USB charger 1000mA or its

Supply Installation, Testing and Commissioning of Server Based PBX SYSTEM

1 MR CONFIGURED FOR 01 PRI / 10 IP-SIP USER / ANALOG EXTN.250 / 04 ANALOG TRUNK Each 1 639613 639612.82

WITH SUPPORTING CARD or its Equivalent

Supply Installation, Testing and Commissioning of Integrated Viocemail System 4 Level IVR

software with 6 different languages and 4 time schedule(As per OEM).

Supply Installation Testing and Commissioning of Digital Phone (24Key+ 60-line DSS

Console) Backlit keypad Hands-free, full duplex ,Headset support Easy to use soft

3 MR keys/LCD prompts,Directory dialling,Navigation wheel,Call history,Backlit LCD Each 1 76823 76823.46

screen,Bluetooth support (BCAZ),Security lock key XML open interface . or its Equivalent

Supply Installation Testing and Commissioning of Digital analog addressable Phone 12 key

display Backlit keypad Hands-free working Easy to use soft keys / LCD prompts on display

4 MR model Directory dial key 1000 system, 1000 group, 10 personal, 600 phone book Each 8 17895 143163.98

Conference key Wall mountable Message waiting indicator. or its Equivalent

5 MR Supply Installation, Testing and Commissioning of Analog Digital Phone. Each 72 2022 145589.41

6 MR Supplying, Installation, Testing & Commissioning of of 200 Port MDF Krone type. Each 1 8913 8913.43

1 MR Supply, installation, testing and commissioning of Wi Fi Access points and Controller

22*2 IEEE 802.11b/g/n/ac Wireless Concurrent Ceiling Access Point with 802.11a:

6/9/12/18/24/36/48/54 Mbps & Auto fallback

- 802.11b: 1/2/5.5/11 Mbps & Auto fallback

- 802.11g: 6/9/12/18/24/36/48/54 Mbps & Auto fallback

Standard Compliances : IEEE802.3u MDI / MDIX 10/100/1000Base-T Ethernet

- IEEE802.11b/g/n wireless LAN standard

- IEEE 802.11a/an/ac wireless LAN standard

Standard Protocol

2 * RJ45 support 10/100/1000Mbps (WAN*1, LAN*1)

1 * Reset button

1 * Power Jack(option) Ethernet Interface 2 *

10/100/1000 BASE-T RJ-45 Ethernet connector

WAN for Power over Ethernet (802.3at) with Cat5e/6 cable

Antenna 2G/5G internal antenna

Antenna Gain 2G -> 5dBi PCB Antenna

5G -> 5dBi PCB Antenna

Network Protection IPS, RED, HTML5 VPN, ATP, Security Heartbeat

Web Protection Anti-malware, Web and App visibility, control, and protection

Email Protection Anti-spam, SPX Email Encryption, and DLP

Web Server Protection Web Application Firewall and reverse proxy

Sandstorm Protection next-gen cloud-sandbox technology

Firewall throughput 3.0 Gbps, Anti-malware throughput 1.3 Gbps, threat Prevention

throughput 1.25 Gbps , Maximum DPI connections 300,000, VPN 1700 MBPS, NGFW 3000

3 MR MBPS, New connections/sec 14,000/sec, Storage module 16 GB Each 1 913283 913282.54

4 GbE copper (incl. 2 bypass pairs) 2 GbE SFP*,

4 port GbE copper, 4 port GbE SFP*, 2 port 10 GbE SFP+*

4 port 10 GbE SFP+*, 2 port 40 GbE QSFP+*, 4 port GE copper LAN bypass

Internal auto-ranging. 100-240VAC, 50-60 Hz Redundant PSU optional

Ethernet interfaces (fixed) 6 GbE copper (incl. 2 bypass pairs),2 GbE SFP

Internet Load Balancer

Dual Gigabit Ethernet Ports, Failover, Load balancing

DHCP server, DHCP client, DHCP relay agent, Static IP, PPTP

Transparent bridge, DNS relay, Dynamic DNS, DNS local database

Routing Information Protocol (RIP) v1 and v2, and RIP for IPv6 (RIPng)

4 MR Data Encryption Standard (DES), Authentication :MD5/SHA1 Each 1 189631 189630.70

Inter-VLAN routing, Static routing, VLANs supported: 7

DMZ port, DMZ host

Port : Four 10/100/1000 Gigabit Ethernet RJ-45 ports

One 10/100/1000 Gigabit Ethernet RJ-45 Internet (WAN) por

One 10/100/1000 Gigabit Ethernet RJ-45 DMZ/Internet (WAN) port

Workstation System

Intel Core 12 with 97% working efficiancy, 64GB RAM, 512GB SSD, DVD Writer USB

5 MR Keyboard & Mouse, Dual Gigabit LAN, HD Graphics, 32" LED Screen, Windows 10 Nos. 1 133878 133877.60

Professional,with licensed antivirous.

SITC of below mentioned item, unit consisting of

SITC of HPE DL380 Gen10 4208 1P 16G 8SFF Svr Xeon-B 4208 8C, 2.1GHz, HP 64GB Nos. 1

7 MR Ram ,, 1xP408i-a ctrlr, 1x96w SS Battery,, 1xCMA for rail kit, 2U SFF easy install rail kit,

1x500W LH PS - 8SFF HP drive cage

8 MR SITC Processor 4208 kit Nos. 1

SITC HPE 16GB (1x16GB) Dual Rank x8 DDR4-2933 CAS-21-21-21 Nos. 4

9 MR Registered Smart Memory Kit

10 MR SITC HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit Nos. 1

11 MR SITC HPE 1.2TB SAS 10K HDD Nos. 4

MR FIRE ALARM & DETECTION & PA SYSTEM

Supplying, installation, testing & commissioning of repeater panel wih 640 character/ Touch

screen LCD display with inbuilt reset, acknowledge and silence switches complete as

2 MR SITC Loop Card capacity of 159 detectors For BMS Fire integration Each 1 80451 80451.00

3 MR SITC of Networking card for BMS integration Each 1 50751 50751.00

Supplying, installation, testing & commissioning of intelligent analog addressable

photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed

5 17.2.5 MS Box having two LED, metallic cover complete with all connections etc as required Each 60 263 15780

Supplying, installation, testing & commisssioning of intelligent addressable programmable

sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as

Supplying, installation, testing & commissioning of intelligent addressable thermal detector

8 17.2.9 with rate of rise cum fixed tempreature thermistor complete with base as required. Each 2 2713 5426

Supplying, installation, testing & commissioning of addressable fire control module

complete as required

Supplying, installation, testing & commissioning of intelligent addressable duct detector

including suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete

Supplying, installation, testing & commissioning of addressable horn cum strobe complete

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with

13 17.5.2 annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer Metre 1360 141 191760

sheath complete as required.

14 17.3 PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB,

15 17.3.1 MP3 player (including 6 zone button paging station) with seamless integration facility with Each 1 126399 126399

main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers

complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5

Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 500 Watt, 25V rms

operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with

microphone assembly complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

21 17.5.3 existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

22 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Metre 1000 51 51000

ACCESS CONTROL SYSTEM

Supply, Installation, testing and commissioning of Surface mounted Networkable

multiprocessor controlled 4Door/4 reader controller capable of controlling multiple readers

1 MR (IN/OUT) alongwith TCP/IP connectivity complete as per specifications. Control panel Nos. 1 103368 103368.12

housed in MS Powder Coated Cabinet with Tamper Switch, Complete with power supply

unit for Controllers & Magnetic Locks as per specification.

Supply, installation, testing and commissioning of Access Control Application Software for

128 Reader Capacity, and 4000 Card Holder Capacity, Basic GUI , TA Module with Alarm

Module, T+ Module, 2-Nos Client Work Stations,Module for using SQL DB , -MULTI Site

Supply , installation, testing & commissioning of smart card I class readers as per

3 MR specification suitable for mounting on metal surface/metal frames or wooden frames wall or Each 4 6029 24117.78

as required based on site conditions including all accessories.

4 MR Supply, testing and commissioning of Exit Push Button Each 4 1166 4664.00

5 MR Supply, testing and commissioning of iClass Smart card . Each 100 247 24699.79

Supply, installation, testing and commissioning of Single Leaf Electro Magnetic Lock of

Suitable Capacity(Min 600 lbs).

Supply, installation, testing and commissioning of Double Leaf Electro Magnetic Lock of

Suitable Capacity(Min 1200 lbs).

8 MR Supply and Fixing of ''U'' Bracket with Accessories. Each 4 1028 4112.00

Supply, fixing & testing of Biomatric Reader cum attendence along with communication and

9 MR USB port suitable for external / Internal environment with Mounting complete as required. Each 1 48896 48896.15

Supply, Fixing and Laying of 8 Core multi strand, copper, unarmoured Cable (between

the every readers & the access controllers).

Supply, Installation, Testing & Commissioning of 4MP IR IP H.265 Vandal Proof Dome

camera with 2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR distance,Up to 80 dB

WDR (Wide Dynamic Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264,

MJPEG,Corridor mode, Triple streams,3-Axis, IP67, IK10 Vandal Resistant,Colour:

0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video Compression H.265+, H.265, H.264,

1 MR MJPEG,Behavior Detection Intrusion, Crossing line, Motion detection, Object left, Missing Nos. 6 21277 127660.89

object,Intelligent Identification Face detection, Defocus, Scene Change,PoE (IEEE802.3 af)

Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to 256GB, ANR

Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-

condensing),Compatible Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing & Commisioning of Ultra wide angle lens, 360” panoramic

image , 5MP IR IP Hemispheric Dome Camera 1.2.8" 5 mega pixel,H.265+, H.265, H.264,

MJPEG,D/3D DNR, progressive scan CMOS,focal 1.4mm @ F2.0 Automatic,WDR

120db,Min. Illumination Colour: 0.01 Lux @F2.0, B/W: 0 Lux with IR, AGC

Auto/Manual,Day/Night IR-cut filter for day & night function,Video Compression H.265+,

H.265, H.264, MJPEG,Frame Rate Main Stream: (2592x1944): Max.30fps; Sub Stream:

2 MR (1920x1080): Max.30fps; Third Stream: D1(720 x 576): Max.30 lps,Smart Analytics Motion Nos 4 36006 144024.60

detection, Audio detection,Watermark, IP Address Filtering, Tampering Alarm, Alarm input,

Alarm output, Access Policy, ARP Protection, RTSP Authentication, User Authentication,

Protocol IPv6, IPv4, IGMPMP, ARP, TCP, UDP, DHCP, PPPoE, RTP, RTSP, RTCP, DNS,

DDNS, NTP, FTP, UPnP, HTTP, HTTPS, SMTP, 802.1x, SNMP, QoS,Support PoE power

supply , ONVIF (Profile S/G), API,IK10, IP66

Supply of Video Management Software with built in Video Analytics management and

recording solution for 10 Nos. Cammera. The intelligent video management software shall

enable management and control of live and recorded video, seamlessly integrating analog

and digital video components. This shall be designed for small and medium sized

deployments and all-in-one architecture shall be based on one standard Server serving as

the recording server, system and client also if required, however separate workstation

should be offered for client usage. The system shall be easy to install, configure, maintain

and provides all levels of security personnel with intuitive and reliable control. This shall

enable fast detection of potential threats and emergency event management.or its

equivalent in specifications

Supply, Installation ,Testing and Commissioning of Video Management Server with 30 days

4 MR storage Server shall be sized according to the solution quoted or its equivalent in Nos. 1 401986 401986.00

Supply, Installation, Testing & Commissioning of 43'' Flat Screen HD led (24X7) with

Interfaces include HDMI, DVI, D-sub, Component and Composite input as well as RS-232C

and RJ45 for extensive connectivity, remote control and wall mount unit / floor stand

complete with making connections etc complete as reqd.

AUDIO VIDEO & CONTROL SYSTEM FOR 30 PAC CONFERENCE ROOM

Supply Installation, Testing and Commissioning of Passive Coulm Array Loudspeaker with

Transducers 16 x 2.75' Diameter, Having a program power of 400 Watts, Peak power 800

With a frequency range of 130Hz to 23kHz (-10dB), 150Hz to 20kHz (-6dB), Modular

design with wide Horizontal coverage of 140º , IP rating of 65 for better protection,

Maximum SPL of 123 dB, Transformer for allowing to operate between 100/70V Should be

supplied with standard accessories.

Supply Installation, Testing and Commissioning of Passive Coaxial 2 Way Ceiling Mounted

Loudspeaker with LF transducer Woofer 5", HF transducer Tweeter 0.5", Power handling of

20W @8 ohms, 100V/70V. Integral multi Tapping of 20W/10W/5W/2.5W available on

100/70V Operations, Usable frequency range of 100 Hz - 20 KHz, With Maximum SPL of

101 db and a coverage of 150º x 150º @ 1 KHz; 80º x 80º @ 4 KHz.

Supply Installation, Testing and Commissioning of Class D compliant Amplifier with

Switching power supply, 4 zone amplifier with Output power of 4X 150W @70/100V,

3 MR Frequency Range 100 Hz - 15 KHz, THD+N < 0.1%, S/N ratio > 95 dB, Factor Damping > Nos 1 73,845 73845.15

200, crosstalk > 70 dB, Protections : Short circuit, open circuit, overtemperature, ultrasonics

Supply Installation, Testing and Commissioning of Digital Audio Conferencing Processor

with 12AEC Mic/Line Input, 8 Line Outputs, 24 bits, 48 kHz sampling rates (uncompressed),

Analog Input Level +24 dBu, Frequency Response ±0 2 dB (20 Hz to 20 kHz), THD+N < 0

003% (1 kHz, +4 dBu), Common Mode Rejection Ration 103 dB @ 60Hz

SNR 110 dB, Analog Dynamic Range 113 dB, Channel Isolation 108 dB (1 kHz), 1 LAN (RJ-

45), 1 USB Audio (Type-B), 1 RS-232 (Terminal Block) 8 GPI/O (Terminal Block)

Supply, Installation, Testing and commissioning of Central Conferenece Engine with

recording capabilities including software for voting ,room layout , agenda, should have have

4 nos Conference Ports or better, Integrated dynamics processor with programmable

threshold, ratio, attack and release of noise gate, AGC and limiter functions, Must have

internal Recording capacity of over 100 hours of audio with Single push button to start or

stop recordings, ON/OFF Power,System Volume,Recording Indicator LED etc, DLP switch

to enable and disable power to the

conference ports, Web Server with User-friendly Interface, 1 no. balanced input and 1 no.

Blanaced output. 2 Unbalanced Cinch audio inputs and 2 Unbalanced Cinch audio outputs,

Audio Routing, Network Monitoring, built-in Diagnostics application and camera control,

Loop cabling for redundance in case of failure of unit. It shall have flexibility to attach

wireless conference units as well if required in future, Should also support Voting &

5 MR Interpretaion feature by addiing additional license if required in future.Option to add DANTE Nos 1 904,386 904386.08

network card for Audio over IP in case required for future seamless integartion.USB port for

expandable memory to record longer meetings, view the reports and meeting history,the

room layout, and voting results during or after a voting session etc. 19" Rack Mountable,

Certification: CE. Country of origin should not be China or its equivalent in specifications

Supply , installation , testing and commissioning of Digital Chairman unit with minimumm

430mm long gooseneck microphone. Microphone connector compatible with standard 3-pin

XLR microphones. Individual adjustable gain control. programmable bottons for Multiple

functions like all delegate mute etc. colour RGB rear LED bar for general visualisation

purposes. Multi-colour LED on the speak button for user’s colour preferences. LED display

for volume control and listening channel selection. High quality speaker for enhanced

6 MR speech intelligibility. 24-bit / 48kHz High Resolution Audio. 2 x RJ45 Port for connecting to Nos 15 132,702 1990536.75

the Control Unit and other Discussion Units and 1 x stereo mini jack headphone output.

Supply Installation, Testing and Commissioning of 2 x 2 Matrix Interactive Video wall;

Screen Size-55" Diagonal, Beezel-0.44 mm (Even Bezel), Panel Technology-IPS, Native

Resolution-1920 x 1080, Brightness (Typ.), 500 NIT, Contrast Ratio : 1100:1, Dynamic

CR1) - 500000:1, Color Gamut - NTSC 72 %, Viewing Angle (H × V)- 178 × 178, Color

Depth -1.07 Billion Colors (10 bit), Response Time-8ms(G to G), Surface Treatment- Haze

28%, Operation Hours (Hours / Day)-24x7, Portrait & Landscape -Yes, Input- HDMI (2), DP,

DVI-D, Audio, USB 2.0 Type A, Output- DP Audio, External Control- RS232C In / Out, RJ45

(LAN) In / Out, IR In, Handle-Yes, Internal Memory (8 GB), Temperature Sensor, Current

Sensor, BLU Sensor, Local Key Operation, webOS 4.0, Embedded CMS (Local Contents

Scheduling, Group Manager), USB Plug & Play, Fail Over, Background Image (No Signal

7 MR Image), Sync Mode (RS-232C Sync, Local Network Sync), Video Tag (2), Play via URL, Set 1 1882671 1882671.00

Rotation (Screen Rotation, External Input Rotation), Gapless Playback, Tile Mode Setting

(Max. 15 × 15), Setting Data Cloning, SNMP, ISM Method, Auto Set ID, Status Mailing,

Control Manager, Crestron Connected®2), Smart Energy Saving, PM Mode, Wake on LAN,

HDMI-CEC3), SI Server Setting, webRTC, Pro:Idiom, Multi Touch Interactive overlay for

(2X2 55" Videowall) 110" Display with 6 Touch Points, 6 mm tempered glass, Black

powered-coated Aluminium Frame, Fingle Glove Touch Method, Finger Touch Accuracy ±

1.5 mm, Touch Durability Unlimited, Touch Response Time 7ms-13ms, Touch Resolution

32767 x 32767, OS Windows 7/8, Mac OS X, Linux(DIsplay Not Included) ( Overlay to be

approved by OEM)

Supply , installation , testing and commissioning of Wall Mount Bracket for Video Wall 55".

Should have Multi-dimensional Micro Adjustment enables precision alignment of the video

wall configuration, including depth, height and tilt. Should have Pop-out extension easily

pulls out for installation and maintenance. Should have Max. Load capacity up to 70 Kg or

more. Should support VESA 200x200 to 600x400. Material should be steel.or its equivalent

in specifications

Supply, Installation, Testing and Commissioning of Interactive Digital Board Wall Mount:

Screen Size : 65" or Higher; Native Resolution : 3840 x 2160 (UHD); Brightness :Minimum

350cd/m2 with protection Glass : Contrast Ratio : 1,100:1 or Higher; Viewing Angle(H x V) :

178 x 178: Surface Treatment : Anti-glare treatment; Min Input ports : HDMI-3,USB(3.0)-

3,USB-(2,0)-2,OPS Slot-1,RGB-1,LAN-1,SPDIF-1 or Higher ; Min Output Ports : HDMI -

1,Audio-1( Audio out to connect additional Speakers if required); External Control : Rs-232;

Built in Touch type : IR spread / PCap / Incell / Inglass ; Touch Accuracy :±1.5mm or less;

Air Gap Between LCD Module & Glass : Minimum 1 mm or less ; Protection Glass

Thickness :4T (Anti-Glare); Operating System Support : Windows 7/8/10/Windows

XP/Linux/Mac/Android; (Windows XP/Linux/Mac Support one point touch) : Multi touch point

: Min 20 Points or Higher; Google CTS :Compatible/Approved to smooth interface;

Interactive Features: White Board ,Writing, Pen, Palm Eraser ,Save, Screen Capture,

9 MR Storage, Tool Bar, Air Class etc.; Built in Standard OS : Android 8.0 or better; Panel Nos 6 143100 858600.27

System on Chip :Internal Memory (16GB),(Hisi 811, Dual core A73+Dual core A53),

DDR(3GB), Wi-Fi, Power Indicator, or higher; Media share : Screen Share/Mira cast to

Connect TAB/Mobile, Web Browser; HEVC Decoder : For zoomed in various documents,

images,& Videos can be displayed without any distortion; PCB Protective Coating

Conformal Coating on PCB to prevent from Humidity , Dust & Iron Particles ; Power Supply :

100-240V~, 50/60Hz; Power Consumption (Typ.) : 265 W or less; Built in Audio Power :

22W(12W x 2) or higher ; Product Quality Certifications :UL,BIS,FCC,CB; India

Certificates/Approvals : ISO9001, ISO14001,OSHAS-18001,E-waste ; Accessory : Remote

Controller(include battery 2ea), Power Cord, QSG, Regulation Book, Touch Pen(2);

Warranty :3 years ; Installation type :Wall mount OEM Warranty : 3 Years onsite

Supply, Installation, Testing and Commissioning of Retractable Cable manager with 2 AC

power outlet, retractors for 1 HDMI, & 2x LAN connection and 1x USB C. Should Provide

Convenient and Easy–to–Use Connecting — Pull the cable to extend up to 1.8m (5.9ft)

from the installation site. The cable automatically locks in position to the desired length.

When finished, pull the cable again to retract it into the housing. Should have High–speed

HDMI with Ethernet Cable Retractor with HDMI connector, 1x USB-C Cable Retractor and

2x CAT 6 Cable Retractor with RJ–45 connector complete with standard accessories as

required.or its equivalent in specifications

Supply Installation, Testing and Commissioning of HDMI and USB C switcher -HDMI and

USB-C input AV switcher, , USB-C input for AV and data both, Integrated USB 3.0 hub,

4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats,

Selectable 4K to 1080p downscaling

, Automatic input selection and automatic display control

Audio de-embedding

Supply Installation, Testing and Commissioning of 2 HDMI Active wall Plate - 2 x1 HDBT

switcher with two HDMI auto switch., One gang enclosure decora style wall plate.

, Wall plate should transmit Video signal/Power and control up to 100 meters using HDBT

link., Wall plate should support resolution up to 4K-UHD@60Hz., Automatic input selection

using hot plug detect ands automatic display control., Active wall plate should support

bandwidth up to 10.2 Gbps., HDCP 2.2 compliance., Input resolution support up to

Supply Installation, Testing and Commissioning of AV over IP Decoder- 2 x1 HDBT switcher

with two HDMI auto switch.,One gang enclosure decora style wall plate., Wall plate should

transmit Video signal/Power and control up to 100 meters using HDBT link., Wall plate

should support resolution up to 4K-UHD@60Hz., Automatic input selection using hot plug

13 MR detect ands automatic display control., Active wall plate should support bandwidth up to Nos 7 119698 837888.10

10.2 Gbps., HDCP 2.2 compliance., Input resolution support up to 4096x2048@60 Hz.

Supply Installation, Testing and Commissioning of AV over IP Encoder - Single channel Av

over IP decoder., Reliability over a 1G ethernet switch., Ability to have local or POE

powering., Resolution support upto 4K@60Hz with HDR, HDCP and EDID management

14 MR over network., Encoder should have LED indication on front panel for Power/source Nos 10 119698 1196983.00

detection/Network link

Supply, Installation,Testing & Commissioning of AVoIP Management Software. Should

support Automatic device detection (up to 50 Devises) reduces configuration time,

15 MR Enhanced security with intuitive user-access management, Remote maintenance with no Nos 1 282519 282518.90

need for on-site visits, Control a virtually unlimited number of devices.or its equivalent in

Supply Installation, Testing and Commissioning of Wireless Presentation Device - Screen

casting and wireless presentation solution with enhanced features to work with all platform

like Miracast, airplay or Googlecast, The device shall be able to present upto 4 or more

screens at the same time, Shall not need any software installation or USB dongle for doing

the wireless presentation, Resolution support for 1080 or more, Shall have functionality to

16 support streaming like Youtube streaming for archival and viewing purpose, Shall allow 1 365018 365018.24

seamless playing of video files without frame-loss, Shall be having provision for being used

as a digital signage media player (additional hardware and software may be added to

achieve the same), Wifi access point shall be integrated (or be added through additional

hardware), Shall have provision for Instructor or moderator mode for allowing the right of

presentation, Shall be controllable over IP and RS-232 both

Supply Installation, Testing and Commissioning of USB Extension Module - •HDBT extender

kit for USB/Power/HDMI/Ethernet for upto 70m or more

•USB 2.0 interface extension upto 70 meters of catx cable length.

•Extender kit should support 4K/UHD cpablity@60Hz with 4:2:0

17 MR •HDCP 2.2 Compliant Nos 1 66904 66903.78

•Extender kit should have Four USB device connectivity with one Host PC connection.

•Transmitter powered by receiver over POE.

•Extender kit should support multi channel audio pass through.

Supply, Installation, Testing and Commissioning of 21.5" Retractable monitor. The Smart

retractable monitor with a professional electrically retractable 21.5” widescreen monitor to

be integrated in furniture. With a 20° automatic tilt, the monitor has a powder coated steel

housing and an up-table cover plate in brushed stainless steel. Should include DVI-I and

18 MR DVI-D inputs which are HDCP compliant. The Smart monitor integrates a patented single Nos 1 409783 409782.65

motor system activated through push buttons placed on the cover plate. The monitor works

with the AHnet protocol (RS422) through CAT5 loop-through cable, individual addressing

and termination switch complete with standard accessories as required.or its equivalent in

Supply, Installation, Testing and Commissioning of Control system have minimum 12

bidirectional RS232, 8 IR, 8 Relays and 8 GP/IO and 1 Ethernet port to control all the

devices in the room. Should have inbuilt or external IR sensor/learner to learn IR commands

The compatible relay controller to control the Projector screen up down should be supplied

as a package (may be from same OEM of controller or different). Should have inbuilt

processing power and internal storage to store and process the control program. Should be

compatible with any (IOS/Android) wireless or wired Touch screen of any size. Additional

ports if required can be added with minimum hassle. Should have the flexibility to add as

19 MR many user interfaces as required. Should have embedded webpage for control port Nos 1 202426 202425.90

settings. Should have Status LED to check for Control/Connection status. It should have

minimum 5 license each included for both iOS & Android application Certification: CE, ISO

9001, ISO 14001, OHSAS 18001. Extra component or equipment maybe added to match

the complete specs. Should be supplied with standard accessories as required.or its

equivalent in specifications

Supply, Installation, Testing and Commissioning of Wall & Table Mount PoE Touch Panel

have 7” or more IPS color screen. Should have minimum 1280 x 800 resolution, brightness

3000cd/m2, contrast ratio 800:1, 16:10 aspect ratio Should have inbuilt Wi-Fi, 802.11

b/g/n/ac, Bluetooth 4.0 Should have capacitive touch technology. Should support

Multitouch. CPU performance: 1.6GHz Quad Core, GPU, 2GB RAM, 16GB flash. Should be

able to decode video format HEVC/H.265, H.264, H.263, MPEG–1/2/4, VC–1, VP6/8,

RV8/9/10, AVS, MVC, Sorenson Spark, M–JPEG Should be able to encode/stream video

format H.264, MVC, VP8, M–JPEG Should have front 2MP camera, HD 720p. Should have

Ethernet port 10/100/1000Mbps PoE LAN. Should have inbuilt mic and speaker. Should be

supplied with standard accessories as required.or its equivalent in specifications

Supply ,installation ,testing and commissioning of Full HD 1080p60 Hardware based VC

endpoint. should support Line input and Line output for audio. . In future should be

upgradable to add 2 more microphones. The video conference system shall support both

H.323 and SIP. The video conference system should work behind a DHCP network without

any NAT, Static IP or Public IP provisioning, • The video codec shall support a minimum

1920x1080 resolution With Progressive Scan @ 30 frames per second. • The video

conference system must have automatic noise reduction, automatic gain control and echo

cancellation. • The video conference system must support full duplex audio for natural

conversations. • The video codec shall support recording of video, audio and presentation to

an external appliance. The codec should support either MPEG4 or H.264 video standards.

When recording using MPEG4, the recording appliance should not be seen to be a

21 MR participant in the call, but shall provide a simple recording notification on screen for all Nos 1 844641 844640.90

participants during the call. • The video conference system shall support NAT/firewall

traversal (H.460/SIP), • The video conference system must support SNMP, • The video

conference system must have backup and restore functionality. • The video codec should

support the following audio and video standards: H.263, H.263+, H.264, G.711, G.722,

G.722.1c, MPEG4-AAC-LC. • The video codec should support secure calling with 128b AES

encryption using H.235 or SRTP/TLS, including strict compliance. • The video conference

system must support Do Not Disturb mode prior to a call and in-call modes. The Video

Conference system should be able to join Microsoft Teams connecting Laptop/PC through

USB.or its equivalent in specifications

Supply, Installation, Testing and Commissioning of Full HD 1080p, minimum 20X Optical

Zoom, min 100 Presets, 60 Frames per Second, Ethernet Out, HDMI Out, 3G-SDI Out,

22 MR Audio In, RS232/422 Controls, -170° ~ +170° Panning angle, -30° ~ +90° Tilting angle , Nos 2 213452 426904.40

Should support PoE. For capturing students. or its equivalent in specifications

Supply, Installation, Testing and Commissioning of HDMI and audio to USB scaling bridge,

with integrated DSP, video processing, a variety of analog audio I/O ports, and signal

management for analog audio, HDMI embedded audio, and USB bidirectional audio

23 MR ,Should be equipped with an internal, universal AC power supply capable of supporting 100 - Nos 1 308863 308862.94

240 VAC, 50/60 Hz power that provide +12 VDC, 100 mA remote power output complete

with standard accessories as required. or its equivalent in specifications

Supply, Installation, Testing and Commissioning of Cat6A jack Panel 24 port Loaded

Shielded. It must be made of cold rolled steel, in 24 port configurations. Should come with

24 MR 24 jack, Each jack for the jack panel must provide a Cap or Shutter to avoid dust and Nos 3 26858 80573.41

contaminates entering the jack & for 100% dust free environment.or its equivalent in

Supply , installation , testing and commissioning of Workstation with i-7 Configuration.

Server: Intel Core i7, such as Intel Core i7-4770 Quad-Core 3.4Ghz 8 GB DDR3-1600 RAM

1 Gbit/s Network Hard drive SATA 6 Gbit/s 7200 RPM Enterprise Class – Up to 48 Mbps per

drive for optimal performance. Client: Intel Core i7, such as Intel Core i7-4770 Quad Core

25 MR 3.4Ghz 8 GB DDR3-1600 RAM , Bandwidth supported - Up to 256 Mbit/s video data. Should Nos 1 100536 100535.62

include Keyboard and Mouse and 21.5" FHD Monitor. Should Include AV Control software

with customized GUI,. Audio Conference Management Software and Window 10.or its

equivalent in specifications

Supply, Installation, Testing and Commissioning of 6 ft High−performance cable that

supports signals up to 4K@60Hz (4:4:4), Deep color

Should have Gold Plated pins.

Should be 28 AWG.

26 MR Triple Shielded — For maximum EMI protection. Nos 20 3412 68235.74

Safety: Flammability Rating — CL3/FT4

Environmental: RoHS 2011/65/ EU

Conductor Resistance – 28AWG: 237.25Ω/km

or its equivalent in specifications

Supply, Installation, Testing and Commissioning of 10 ft High−performance cable that

supports signals up to 4K@60Hz (4:4:4), Deep color

Should have Gold Plated pins.

Should be 28 AWG.

27 MR Triple Shielded — For maximum EMI protection. Nos 10 4156 41555.78

Safety: Flammability Rating — CL3/FT4

Environmental: RoHS 2011/65/ EU

Conductor Resistance – 28AWG: 237.25Ω/km or its equivalent in specifications

Supply, Installation, Testing and Commissioning of 6 ft USB2.0/ 3.0 Type−A male to Type−A

male cable used to connect computers and peripherals, such as printers, scanners,

cameras, keyboards, mice and other digital devices for superior signal transfer of up to

4.8Gbps.or its equivalent in specifications

Supply, Installation, Testing and Commissioning of Shielded 4 twisted pair cable.

High−quality low−smoke, halogen free cable. Should have 4 shielded twisted pairs (U/FTP)

of 23AWG solid Annealed copper conductors Should have outer jacket with Material: LSHF,

Thickness: ≥0.5mm, Diameter: 7.2mm ±0.2mm Should have Drain wire with material:

Tinned copper, Diameter: 0.4mm ±0.01mm Should have Delay Skew: <45ns, Propagation

Velocity (NVP): 76% Should have electrical Impedance: 1–100MHz: 100Ω ±15Ω,

29 100–250MHz: 100Ω ±20Ω, 250–500MHz: 100Ω ±25Ω Operation Temperature: –20˚C to 4 31795 127179.42

+60˚C COMPLIANCE - Electrical: EIA/TIA 568A, ISO/IEC 11801, Fire Performance: IEC

60332 1, Smoke Density: IEC 61034, Halogen Free: IEC 60754, RoHS: 2011/65/EU,

Reaction to Fire Classification: Dca–s2,d1,a1 (optional: B2ca–s1,d1,a1) Should be

recommended by HDBaseT Should be from the same OEM as of video switcher Shall be

supplied with adequate no of connectors for this shielded CAT6A cable from the same OEM

complete with standard accessories as required.or its equivalent in specifications

Supply, Installation, Testing and Commissioning of High quality Twisted pair cable, 16 AWG

(26/30) bare copper conductor, Insulation material: PVC, rugged and flexible PVC jacket

with sequential markings every meter, Temperature rating: 75˚C, Certification: UL: CM,

RoHS: 2011/65/ EU or its equivalent in specifications

Supply, Installation, Testing and Commissioning of Bulk connector such as XLR

31 MR (Male/Female), Speakon, Contol connector, 3.5 mm stereo audio jack, RJ-45 Shielded etc. Lot 1 40199 40198.56

as required. or its equivalent in specifications

Supply, Installation, Testing and Commissioning of IR emmiter to control the IR devices

32 MR such as DVD player. Should be supplied with standard accessories as required. or its Nos 2 4278 8556.89

equivalent in specifications

33 MR Director Room 3 Nos And CMD Cabin 1 No.

Supply, Installation, Testing and Commissioning of Retractable Cable manager with 2 AC

power outlet, retractors for 1 HDMI, & 2x LAN connection and 1x USB C. Should Provide

Convenient and Easy–to–Use Connecting — Pull the cable to extend up to 1.8m (5.9ft)

from the installation site. The cable automatically locks in position to the desired length.

When finished, pull the cable again to retract it into the housing. Should have High–speed

HDMI with Ethernet Cable Retractor with HDMI connector, 1x USB-C Cable Retractor and

2x CAT 6 Cable Retractor with RJ–45 connector complete with standard accessories as

required.or its equivalent in specifications

Supply Installation, Testing and Commissioning of HDMI and USB C switcher -HDMI and

USB-C input AV switcher, , USB-C input for AV and data both, Integrated USB 3.0 hub,

4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats,

Selectable 4K to 1080p downscaling

, Automatic input selection and automatic display control

Audio de-embedding

Supply, Installation, Testing and Commissioning of 2–Port Universal I/O PoE Control

Gateway. The ports can be configured as bidirectional RS−232, crossed RS−232, RS−485,

IR, GPI/O or relay control connections. Multiple control clients can be IP−connected to

control gateway for concurrent control of devices. Port: 2 RS–232/IR universal–IO ports on

36 MR 3–pin terminal blocks, each selectable as one of:— 1 bidirectional RS–232 serial port, — 1 Nos 1 57012 57012.40

crossed bidirectional RS–232 serial port, — 1 bidirectional RS–485 serial port, — 2 IR

emitter ports, — 2 GPI/O ports, — 2 relay ports, 1 LAN on an RJ–45 female connector, 1

built–in IR sensor for IR learning, 1 mini USB connector for local services.or its equivalent in

Supply, Installation, Testing and Commissioning of Wall & Table Mount PoE Touch Panel

have 7” or more IPS color screen. Should have minimum 1280 x 800 resolution, brightness

4000cd/m2, contrast ratio 800:1, 16:10 aspect ratio Should have inbuilt Wi-Fi, 802.11

b/g/n/ac, Bluetooth 4.0 Should have capacitive touch technology. Should support

Multitouch. CPU performance: 1.6GHz Quad Core, GPU, 2GB RAM, 16GB flash. Should be

able to decode video format HEVC/H.265, H.264, H.263, MPEG–1/2/4, VC–1, VP6/8,

RV8/9/10, AVS, MVC, Sorenson Spark, M–JPEG Should be able to encode/stream video

format H.264, MVC, VP8, M–JPEG Should have front 2MP camera, HD 720p. Should have

37 MR Ethernet port 10/100/1000Mbps PoE LAN. Should have inbuilt mic and speaker. Should be Nos 1 179765 179765.23

provided with table mount & wall mount kit. Secured Operation - Highly secured operation of

applications using password protection, hidden control buttons and more. Red LED alert

when camera is active. should be possible with Customized GUI using same OEM GUI

Software. should support native integration of same OEM enterprise management software.

Certification: CE, FCC, ROHS, REACH, ISO 9001, ISO 14001, OHSAS 18001. Extra

component or equipment may be added to match the complete specs. Should be supplied

with standard accessories as required.or its equivalent in specifications

Supply, Installation, Testing and Commissioning of IR emmiter to control the IR devices .

38 MR Should be supplied with standard accessories as required.or its equivalent in specifications Nos 1 4278 4278.00

Supply, Installation, Testing and Commissioning of 4 zone lighting control system with

capacity of 1900 watts, should Provide push-button recall of four preset lighting scenes.

Controls virtually any light source without an interface. Includes built-in infrared receiver for

operation, Input Power: 230V (CE), 50Hz., Sources/Load Types: Operates these sources

with a smooth continuous Square Law dimming curve or on a full conduction non-dim basis:

Incandescent, Electronic low voltage, Magnetic low voltage, Neon and cold

cathode.complete with standard accessories as required. or its equivalent in specifications

Supply, Installation, Testing and Commissioning of Shielded 4 twisted pair cable.

High−quality low−smoke, halogen free cable. Should have 4 shielded twisted pairs (U/FTP)

of 23AWG solid Annealed copper conductors Should have outer jacket with Material: LSHF,

Thickness: ≥0.5mm, Diameter: 7.2mm ±0.2mm Should have Drain wire with material:

Tinned copper, Diameter: 0.4mm ±0.01mm Should have Delay Skew: <45ns, Propagation

Velocity (NVP): 76% Should have electrical Impedance: 1–100MHz: 100Ω ±15Ω,

40 100–250MHz: 100Ω ±20Ω, 250–500MHz: 100Ω ±25Ω Operation Temperature: –20˚C to 1 37472 37471.97

+60˚C COMPLIANCE - Electrical: EIA/TIA 568A, ISO/IEC 11801, Fire Performance: IEC

60332 1, Smoke Density: IEC 61034, Halogen Free: IEC 60754, RoHS: 2011/65/EU,

Reaction to Fire Classification: Dca–s2,d1,a1 (optional: B2ca–s1,d1,a1) Should be

recommended by HDBaseT Should be from the same OEM as of video switcher Shall be

supplied with adequate no of connectors for this shielded CAT6A cable from the same OEM

complete with standard accessories as required. or its equivalent in specifications

Supply, Installation, Testing and Commissioning of 6 ft High–Speed HDMI Cable.

High−performance cable that supports signals up to 4K@60Hz (4:4:4), Deep color Should

have Gold Plated pins. Should be 28 AWG. Triple Shielded — For maximum EMI

protection. Safety: Flammability Rating — CL3/FT4 Environmental: RoHS 2011/65/ EU

Conductor Resistance – 28AWG: 237.25Ω/km complete with standard accessories as

required. or its equivalent in specifications

Supply, Installation, Testing and Commissioning of 35 Feet 4K HDMI cable. Should be High

Speed with Ethernet HDMI Cable.

Supports signals up to 4K@60Hz (4:2:0), Deep Color. Should have 24k gold Plated pins.

Should support Data Transfer rate of upto minimum 10GBps.

42 MR Should support of upto 48 bit Deep Color. Should be 26AWG (7/0.160). Connectors must Nos 4 17656 70622.89

have a minimal locking capability to prevent ousting of cables from ports. Should have an

overall shield against EMI/RFI interference. Safety: Flammability Rating — CL3/FT4.

Environmental: RoHS 2011/65/ EU or its equivalent in specifications

43 MR Supply ,installation ,testing and commissioning of Bulk connectors as required. Lot 4 6582 26328.90

45 MR Centerlized Digital Call Bell

Supply, installation, testing & commissioning of Wired Call Bell System with High Glow

Digital Numeric Display and Inbuilt Bell for 14 Users.

47 MR Supply, installation, testing & commissioning of push button. No. 12 1508 18101.12

TOTAL of DSR & MR heads 1546436 21869635.84

Grand Total 23416071.84

Grand Total 23416071.84

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS

LIMITED, 4TH FLOOR, PLATE B , TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE BLOCK 1 , NEW

DELHI TOTAL AMOUNT TOTAL AMOUNT

DELHI TOTAL AMOUNT TOTAL AMOUNT

S No DSR 2019/ MR DESCRIPTION UNIT QTY RATE DSR (INR) NON-DSR (INR)

Providing, laying, testing & commissioning of 'C' class

heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges,

DSR WET RISER & tapers, nuts bolts, gaskets etc. and fixing the pipe on the

SPRINKLER 2019 wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint

of required shade complete as required :

Providing and fixing ISI Marked of approved make Fire

2 MR Extinguishers complete with all accessories as per

manufacturer's specifications.

MR a) CO2 gas nozzle type - 4.5 Litre capacity (IS:15683). NOS 3 4885.88 14657.63

b) Mechanical Foam gas cartridge type. 4.5 Kg capacity

c) ABC dry powder stored pressure type 4.5 kg capacity

Providing, fixing, testing & commissioning of 15mm dia

DSR WET RISER &

3 quartzoid bulb type sprinklers of rating 68 degree

centigrade with required accessories :

21.4 Concealed sprinkler Each 175 1397.00 244475.00

Supplying, installation, testing & commissioning of sprinkler

flexible pipe (UL Listed) of stainless steel complete with 15

NPT on reducer thread with maximum working pressure of

DSR WET RISER & 175 PSI test pressure of 875 PSI (Burst) with branch line

4 SPRINKLER 2019 (Inlet) 25mm NPT male thread to sprinkler head (Outlet)

Item no. 25 15mm NPT female thread with reducer, nipple, 2 side

brackets, center bracket, stockbar of following sizes complete

Supplying & Fixing of battery operated illiminated "EXIT"

5 MR signage, with 2hrs power Battery backup complete as Nos 8 3329.07 26632.53

Supplying,fixing,testingandcommissioningofbutterfly

DSR WET RISER & valveofPN1.6ratingwithbronze/gunmetalseatdulyISImarke

SPRINKLER 2019 dcompletewithnuts,bolts,washers,gasketsconforming to

IS 13095 of following sizes as required

DSR WET RISER &

Providing & fixing of pressure switch in M.S. pipe line

including connection etc. as required.

DSR WET RISER &

Providing & fixing flow switch in following sizes M.S.pipe

8 SPRINKLER 2019

including connection etc as required

GRAND TOTAL 993825.48

GRAND TOTAL 993825.48

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE B ,

TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE BLOCK 1 , NEW DELHI

Ref DSR - Amount(Sc Amount(Non

S.no 2018 Item Description of item Unit Qty Rate (in Rs.) hedule Schedule

no Items) Rs Items) Rs

SANITARY INSTALLATION , DRAINAGE PIPE, FITTINGS & LIFTING

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per

IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including

painting of fittings and brackets, cutting and making good the walls

wherever required :

17.10.1 Kitchen sink with drain board

17.10.1.3 510x1040 mm bowl depth 200 mm (For Kitchen, Pantry) Each 2 5584.10 11168

Providing and fixing CP Brass 32mm size Bottle Trap of approved

quality & make and as per the direction of Engineer-in-charge.

3 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :

18.21.2.1 15 mm nominal bore Each 30 83 2490

Providing and fixing C.P. brass angle valve for basin mixer and geyser

points of approved quality conforming to IS:8931

18.53.1 a) 15 mm nominal bore Each 35 532.00 18620

Providing and fixing wall mounted wash down European water closet

with soft close seat and cover with fixing and 2/4 liter. flushing cistern

5 MR-1 with chrome flush plate, including flush pipe, with all fittings and fixtures Each 2 8378.95 16757.8998

complete, including cutting and making good the walls and floors

wherever required.

Supplying, Installation, testing & commissioning of table top basin with

C.P. brass long body sensor tap with flow rates less than 2 LPM along

with thermostatic diverter required, 32mm C.P. brass waste of standard

Providing and Fixing C.P. brass Sink mixer with Swinging Casted spout

7 MR-3 & connecting legs and flanges, including cutting and making good the Each 2 3331.08 6662.162

walls wherever required.

Providing and fixing C.P. brass bib cock with wall flange of approved

make. Make- Jaquar Model No.

Providing and fixing ABS Chrome plated Hand Shower (Health Faucet)

in with 8 mm dia, 1 Meter long Flexible tube in chrome & wall hook

including cutting and making good the walls wherever required complete

as per instructions of the engineer-in-charge.

Providing, fixing, testing and commissioning of CP brass two way bib

10 MR-6 cock of approved make. Each 9 1294.00 11645.97165

Supplying, Installation, Testing and Commissioning of five star rated

11 MR-7 vertical / horizontal storage type hot water heater fixed to wall with anchor

bolts & nuts all complete work.

Providing and Fixing CP towel ring complete with brackets fixed to

12 MR-8 stainless steel with CP brass screws with concealed fitting arangement of Each 5 935.27 4676.32525

approved quality colour.

Providing and fixing of fully automatic "NO TOUCH" hand dryer in

Stainless steel body suitable to operate on 230 volts, single phase 50 hz,

A.C. power supply and directly plugged to power point complete.

Providing and Fixing Tissue paper Dispenser with stainless steel and

14 MR-10 C.P. brass screws including cutting and making good the wall wherever Each 5 1268.37 6341.86575

Providing and fixing wall mounted liquid soap Dispenser automatic in

stainless steel and C.P. brass screws including cutting and making good

the wall wherever required.

Providing and fixing C.P cast brass coat hook fixed to PVC cleats with

16 MR-12 C.P. brass screws complete as per instructions of the engineer-in- Each 5 538.10 2690.4885

Providing and fixing 125mm grating with ring and S.S anti cockroach

17 MR-13 trap down to the ring with s/s screws and embedding and setting ring into Each 2 1619.97 3239.932242

the floor with cement mortar .

Providing and fixing cast brass cleanout plug with suitable insert

keys for opening, male threaded joint with G.I. socket caulked to spun

soil pipe including cost of lead joint etc. complete. .

Providing solid pedal type bin in SS304 with 7-10 ltr capacity for

19 MR-15 washrooms with inner removable container as per specifications and as Each 6 867.53 5205.160926

per directions of engineer in charge.

Providing and fixing toilet paper holder with mobile stand complete as per

20 MR-16 specification, as required and as per direction of engineer in charge. Each 5 1268.37 6341.86575

Providing and fixing perfume dispenser in ABS as per specifications , as

required as per direction of engineer in charge.

Supplying, installing, testing and commisioning of PP mineral filled low

noise pipes and fittings, with push fit rubber ring sockets pipes and

fittings confirming to EN-12056, with density 1.9gm/cm . Piping is to be

suspended from ceiling level & fixed on ceiling with necessary fittings and

cutting the pipe to the required length including short pieces, assorted

fittings such as Plug / Plain Tee / Swept Tee with or without door, bends

and elbows or any other standard fittings are included in the rate. The

22 MR-18 pipe should have B1 fire classification according to EN4102 and is hot

water resistant up to 95⁰C for short term loading & 90⁰C long term

loading and has chemical resitance of pH 2-12 and completly provides

sound protection upto 10 dB at a flow rate of 2 LPS and giving water

tightness test for all the piping (refer technical specifications for additional

details.) The rate shall include chasing of walls, laying of pipes as per

standard working procedures.

All the internal drainage pipes are to be suspended below the ceiling level

and the pipes are to be supported by modular clamps. The rate includes

the cost of all types of clamping and no other separate rate shall be

The supports required for the Pipes should be made up of cold rolled

steel of quality DX51 or greater with minimum GSM of 275 or greater and

should have universal mounting slot on the front of the rail for accurate

positioning of fasteners and system compatible round and long holes on

back of the rail the pipe.

The pipe clamps should be either split type with EPDM inner rubber lining

or should be MSS-SP manufactured with FM approval and UL listing.

Threaded rods should be of 4.8 strength class or greater and necessary

accessories such as Hexagonal Nuts and Bolts should be of 8.8 strength

Make for Low Noise Drainage Pipes: Poloplast, Astral (Silencio)

Make for Pipe Supports: Mupro, Hilti, Fixotec

18.1 DN 40 mm o/d PP mineral filled SWR pipe RMT 10 473.46 4734.613213

18.2 DN 50 mm o/d PP mineral filled SWR pipe RMT 10 622.78 6227.83738

18.3 DN 75 mm o/d PP mineral filled SWR pipe RMT 15 739.33 11089.92095

18.4 DN 110 mm o/d PP mineral filled SWR pipe RMT 10 1256.49 12564.93506

Providing & Fixing Low Noise Multi Floor Trap with minimum 50mm

water seal having 3nos of DN 50mm inlets and 1nos of DN 110mm Top

inlet and 1nos of DN 75mm outlet. The baffle construction should be air

tight under all circumstances. The inspection plug should enable to

access the area under the baffle in order to inspect and clean the area.

The Floor Trap volume should be in such a way that a maximal discharge

capacity is reached. In case not all the inlets are used two PP-blind plugs

are added to the Floor Trap. These blind plugs should secure a leakage

free sealing of unused connections to the Floor Trap.

Providing and fixing uPVC floor drain of 100x63 size inlet and outlet

24 MR-20 including cutting and making good the walls and floors wherever Each 5 273.15 1365.753811

required complete in all respects.

Providing, fixing and commissioning of toilet waste water super quite

Portable Pumping station Pump upto vertical 5mtr and horrizontal 100

meter from toilet to vertical shaft with inlet connection in portabel pump

Side inlet of 50,75,110 as per requirement to complete the work as per

the direction of engineer in charge.

TOTAL SANITARY INSTALLATION 42875 880954

2 INTERNAL WATER SUPPLY SYSTEM

Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as

per JIS standard 3448 complete with press type fitting (fitting shall be

paid for separately) i/c fixing of the pipe with clamps at 1.00 m spacing

1 18.85 including cutting and making good the walls including testing of joints

complete as per direction of Engineer-in-charge. (The pipe length

inserted in the fitting shall not be measured for payment) Inernal work -

Exposed on wall

18.85.1 15.88 mm outer dia pipe Metre 31 325.2 10081

18.85.2 22.22 mm outer dia Pipe Metre 40 484 19360

18.85.3 28.58 mm outer dia Pipe Metre 80 560.25 44820

18.85.4 34.00 mm outer dia Pipe Metre 50 737.3 36865

18.85.5 42.70 mm outer dia Pipe Metre 50 762.95 38148

18.85.6 48.60 mm outer dia Pipe Metre 121 1000.35 121042

Providing and fixing Stainless Steel pipe and fitting of grade AISI 304

as per JIS standard 3448 complete with press type fitting (fitting

shall be paid for separately) i/c fixing of the pipe with clamps at

2 18.86 1.00m spacing and also including cutting of chases and making

good the walls including testing of joints complete as per direction of

Engineer -in-charge. (The pipe length inserted in the fitting shall not

be measured for payment)

Internal work Concealed Pipe

18.86.1 15.88 mm outer dia pipe Metre 30 478.65 14360

18.86.2 22.22 mm outer dia Pipe Metre 20 637.40 12748

Providing and fixing required Stainless Steel Fitting of press fit design of

grade AISI 304 conforming to JWWA G116 standard with V-profile or

Mprofile and with O-ring sealing gasket of EPDM material of required dia

as per dirction of Engineer-in-charge.

Coupling/Socket

18.87.1 15.88 mm outer dia pipe Metre 15.34 78.95 1211

18.87.2 22.22 mm outer dia Pipe Metre 20 84.30 1686

18.87.3 28.58 mm outer dia Pipe Metre 10 119.10 1191

18.87.4 34.00 mm outer dia Pipe Metre 10 175.25 1753

18.87.5 42.70 mm outer dia pipe Metre 7 211.40 1480

18.87.6 48.60 mm outer dia pipe Metre 10 240.85 2409

Providing and fixing required Stainless Steel Fitting of press fit design of

grade AISI 304 conforming to JWWA G116 standard with V-profile or

Mprofile and with O-ring sealing gasket of EPDM material of Providing

and fixing required Stainless Steel Fitting of press fit design of grade AISI

304 conforming toJWWA G116 standard with V-profile or M-profile and

with O-ring sealing gasket of EPDM material of required dia as per

dirction of Engineer-in-charge.

18.88.1 For 22.22 mm x 15.88 mm outer dia pipe Each 10 137.80 1378

18.88.2 For 28.58 mm x 15.88 mm outer dia pipe Each 10 188.65 1887

18.88.3 For 28.58 mm x 22.22 mm outer dia pipe Each 15 194.00 2910

18.88.4 For 34.00 mm x 15.88 mm outer dia pipe Each 5 246.20 1231

18.88.5 For 34.00 mm x 22.22 mm outer dia pipe Each 6 250.20 1501

18.88.6 For 34.00 mm x 28.58 mm outer dia pipe Each 10 254.20 2542

18.88.10 For 42.70 mm x 34.00 mm outer dia pipe Each 5 517.80 2589

18.88.14 For 48.60 mm x 34.00 mm outer dia pipe Each 5 548.55 2743

Providing and fixing required Stainless Steel Fitting of press fit design of

grade AISI 304 conforming to JWWA G116 standard with V-profile or

Mprofile and with O-ring sealing gasket of EPDM material of required dia

as per dirction of Engineer-in-charge.

Slip Coupling/ Socket

18.89.1 For 15.88 mm outer dia pipe Each 20 62.90 1258

18.89.2 For 22.22 mm outer dia pipe Each 20 84.30 1686

18.89.3 For 28.58 mm outer dia pipe Each 15 119.10 1787

18.89.4 For 34.00 mm outer dia pipe Each 15 175.25 2629

18.89.5 For 42.70 mm outer dia pipe Each 10 211.40 2114

18.89.6 For 48.60 mm outer dia pipe Each 10 227.45 2275

Providing and fixing required Stainless Steel Fitting of press fit design of

grade AISI 304 conforming to JWWA G116 standard with V-profile or

Mprofile and with O-ring sealing gasket of EPDM material of required dia

as per dirction of Engineer-in-charge

18.90.1 For 15.88mm outer dia pipe Each 10 77.60 776

18.90.2 For 22.22 mm outer dia pipe Each 8 84.30 674

18.90.3 For 28.58 mm outer dia pipe Each 6 128.45 771

18.90.4 For 34.00 mm outer dia pipe Each 4 145.85 583

18.90.5 For 42.70 mm outer dia pipe Each 2 155.20 310

18.90.6 For 48.60 mm outer dia pipe Each 2 200.70 401

Providing and fixing required Stainless Steel Fitting of press fit design

of grade AISI 304 conforming to JWWA G116 standard with V-profile

7 18.91 or M-profile and with O-ring sealing gasket of EPDM material of

required dia as per direction of Engineer-in-charge.

18.91.1 Reducing Elbow 90o

For22.22 mm x 15.88 mm outer dia pipe Each 25 198 4950

Providing and fixing required Stainless Steel Fitting of press fit design of

grade AISI 304 conforming to JWWA G116 standard with V-profile or

Mprofile and with O-ring sealing gasket of EPDM material of required dia

as per dirction of Engineer-in-charge.

Male Thread Tee

18.94.1 For 15.88 mm outer dia x 15 mm nominal dia threaded Each 15 239.50 3593

18.94.2 For 22.22 mm outer dia x 15 mm nominal dia threaded Each 20 267.60 5352

18.94.3 For 22.22 mm outer dia x 20 mm nominal dia threaded Each 12 274.30 3292

18.94.4 For 28.58 mm outer dia x 20 mm nominal dia threaded Each 20 365.25 7305

18.94.5 For 34.00 mm outer dia x 20 mm nominal dia threaded Each 8 365.25 2922

18.94.12 For 42.70 mm outer dia x 20 mm nominal dia threaded Each 5 913.80 4569

18.94.19 For 48.60 mm outer dia x 32 mm nominal dia threaded Each 5 1186.75 5934

Providing and fixing required Stainless Steel Fitting of press fit design of

grade AISI 304 conforming to JWWA G116 standard with V-profile or

Mprofile and with O-ring sealing gasket of EPDM material of required dia

as per dirction of Engineer-in-charge

Female Thread Tee

18.95.1 For 15.88 mm outer dia x15 mm nominal dia threaded Each 15 239.50 3593

18.95.2 For 22.22 mm outer dia x 15 mm nominal dia threaded Each 10 267.60 2676

18.95.3 For 22.22 mm outer dia x 20 mm nominal dia threaded Each 15 267.60 4014

18.95.4 For 28.58 mm outer dia x 20 mm nominal dia threaded Each 10 365.25 3653

Providing and fixing required Stainless Steel Fitting of press fit design

of grade AISI 304 conforming to JWWA G116 standard with V-profile

10 18.96.1 or M-profile and with O-ring sealing gasket of EPDM material of

required dia as per direction of Engineer-in-charge.

Female Thread Connector/ Adapter

18.96.1 For 15.88 mm outer dia x 15 mm nominal dia threaded 15 254.20 3813

18.96.2 For 22.22 mm outer dia x 15 mmnominal dia threaded 10 307.75 3078

18.96.3 For 22.22 mm outer dia x 20 mm nominal dia threaded 20 317.10 6342

18.96.4 For 28.58 mm outer dia x 20 mm nominal dia threaded 15 370.60 5559

18.96.5 For 28.58 mm outer dia x 25 mm nominal dia threaded 12 382.65 4592

Providing and fixing gun metal gate valve with C.I. wheel of approved

11 18.17 quality (screwed end) :

18.17.1A 20mm dia nominal bore Each 10 460.20 4602

18.17.1 25mm dia nominal bore Each 2 497.15 1094

18.17.2 32mm dia nominal bore Each 2 581.25 1279

18.17.3 40mm dia nominal bore Each 2 678.40 1492

18.17.4 50mm dia nominal bore Each 2 869.20 1912

TOTAL WATER SUPPLY SYSTEM 467685.32 880954.32

Name of Works : INTERIOR FIT OUT WORKS IN THE OFFICE SPACE OF HINDUSTAN AERONAUTICS LIMITED, 4TH FLOOR, PLATE B , TOWER 1 , EAST KIDWAI NAGAR, NBCC OFFICE BLOCK 1 , NEW DELHI

DSR Rate DSR Amount MR Amount

DSR/MR SUMMARY OF COSTS UNIT QTY. MR Rate (In Rs.)

A.05 HVAC WORKS

PART A AIR-CONDITIONING SYSTEM

1 Dismantling, removing and disposing off of existing Units,ducts,piping ,valves etc complete along

with its supply air grilles, dampers and insulation.

2 MR DX TYPE HI WALL UNIT WITH ISOLATOR

Supply , installation, testing & Commissioning of DX type split AC units with air cooled condenser

mounted in outdoor unit complete with scroll/rotary compressor ,condensor ,wiring & accessories .

Indoor units shall be wall mounted type complete with evaporator ,fan, filter ,drier, expansion

devices & microprocessor control panel along with all accessories with refrigerant & oil charge ,

cordless remote controls. The unit shall be suitable for working ,50 cycle /second ,1 phase AC supply

.The unit shall be designed to take care of veritcal head 8mt & horizontal length of 10 mt & necessary

oil seprator shall be included ,Necessary supporting arrangement for both indoor & outdoor units (

Powder Coated /Epoxy painted MS stand for ODU units as per approved make shade by Architect)

with necessary vibration isolation arrangement as per site condition etc.( without condensate drain

pipe ,electrical pipe ,electrical power & control cabling between indoor & outdoor unit which shall be

paid seprately ). The Color of the outdoor units to be finalized by the Architect as per building

Architectural elevation.

The coil in the outdoor units shall be provided with anti corrosive treatment . The contractor shall

visit the site & check the pollutant level such as Sulphur content & harmful acid content in the

atmosphere near site & accordingly anticorrosive paint treatment of coil to be provided.

All Unit shall be Minimum 3 Star Rating Based

Civil Work such as wall hole making , wall chisling ,refilling of chiseling part with mortar etc as per site

Nitrogen pressure testing for leakages & flushing during installation & after commissioning between

IDU & ODU with flar nuts

Removable Covers for all indoor & Outdoor units shall be supplied & put on the units after

installation & commissioning.

Incoming power supply shall be provided near each indoor units

Inclusive of Stablizer & Timer controller.

DX TYPE HI WALL UNIT

MR 1.5 TR split air conditioning units (Server Room)-1W+1S Nos 4 61669 246,677.26

MR 2.0 TR split air conditioning units (UPS Room)-1W+1S & 2 NO standby for officers Nos 4 68075 272,300.96

3 Supply, installation, testing and commissioning of duct mounted air purification system/ cell based on

Photohydroionization cell with the capability to produce friendly oxidizers like Ionized Hydro

Peroxides, Super Oxide Ions, Hydroxides Ions with quad metalic coating (Rohdium, silver, copper and

titanimum) and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into

the conditioned/ served space. The honeycomb matrix shall not be accepted. The units should be

designed after undertaking a load factor calculation for each specific area where the equipment is to

be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the

units. The system shall be capable of reducing microbial bacteria, virus and spores , VoC’, odors. The

equipment shall conform to UL 1598 CAN/CSA C222 EN60335-1, EN60335-2-65, EU standards,

certifications shall be submitted along with the technical submital.

MR 5500 CFM/2Nos/49 Watt Each Nos 6 136125 816,748.51

PART B PIPING SYSTEM

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of

chilled water piping inside the building (with necessary clamps, vibration isolators

and fittings but excluding valves, strainers, gauges etc.) duly insulated with 80 kg/

cum density resin bonded fiber glass or 144 Kg / cum density mineral wool

insulation (non combustible) pipe section insulation covered with a layer of 120

gm/sqm polythene sheet (vapour barrier) and finally applying 0.63mm aluminium

1 16.1 sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as

amended up to date ) at joints and repairing of damage to building etc. as per

specifications and as required. Note: The Pipes of sizes 150mm & below shall be M.S. 'C' class as per

IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS:

3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum

7mm thick MS sheet for pipes of 400 mm dia and above.

16.1.8 100 mm dia (50mm thick Insulation) MS PIPE Metre 10 2545 25450

16.1.9 80 mm dia (50mm thick Insulation) MS PIPE Metre 10 2151 21510

16.1.10 65 mm dia (50mm thick Insulation) MS PIPE Metre 20 1837 36740

16.1.11 50mm dia (50mm thick Insulation) MS PIPE Metre 30 1546 46380

16.1.12 40 mm dia (50mm thick Insulation) MS PIPE Metre 40 1349 53960

2 LOW SIDE VALVES

Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled

16.7 water plumbing duly insulated to the same specificationsas the connected piping and adequately

supported as per specifications.

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O-Ring PN 16 pressure

rating for chilled water/hot eater circulation as specified

Supply, Installation, Testing, & Commissioning of Automatic air vent with ball valve in brass

3 MR construction complete with nipples, union etc. as required at all high points in the pipe lines. The

valve shall be such as to have non-return valve as integral part of the vent.

MR 15 mm dia auto air vent valve Nos. 6 769.31 4,615.84

Supply, Installation, Testing & Commissioning of 25mm diameter Drain Valves in dirt legs complete Nos. 6

with nipples as per specifications.

5 REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

DSR VRF/VRV following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with