REPAIR AND MAINT WORKS OF WATER SUPPLY INSTALLATIONS AND PIPE LINE NETWORK AND CONNECTED WORK AT SWIMMING POOL, KLP AND ADJOINING AREA AT BABINA CANTT

Amount

M & L for repairing leakages or blockage of water in DI/cast iron pipes with spigot and socket ends of 50 to 80 mm dia bore de-watering of leaking pipe lines and trenches, burning out remains of existing lead joints to recover available quantity of lead and making new lead joint with retrieved material by providing additional quantity of lead as required at site incl all other jointing materials and testing complete all as specified and as directed. Notes : 1. Total excavation and earth work as required at site to carry out the repair work is deemed to be included in the quoted rates. No separate cost for earth work claim by the contractor.2. Actual quantity of lead retrieved from leaking joints may vary from joint to joint and the same be considered to the barest minimum owing to loss due to high pressure of water jet and flooding of water from the joints. 3. No any claim whatsoever in this regard by the contractor for loss or non-retrival of jointing materials shall be admissible and the rate quoted is deemed to be inclusive of this aspect. Note:- Contractor will be intimated telephonically followed in writing for attending the leakages/broken or no water supply defects or repair works under this item.The defects or repair works under this item. the defects will be attended with in 8 Hrs of intimation and work will completed within 24 Hrs ofter intimation of defects failing which a penal recovery of Rs 2000/- per hour will be deducted from contractor's payments. Contractor has to arrange all T & P and manpower to attend defects on time without any extra financial effectand cost of all such aspect is deemed to be imcluded in unit rate.

Discription as per item No 1 here in before but dia of pipe 100 TO 200 mm bore

Discription as per item No 1 here in before but dia of pipe 250 TO 300mm bore

Construction of Valve pit of size 1050cm x 1050cm x 900cm (internal dimensions), Stone masonry construction,including all necessary excavation and earth work in hard/ dense soil,returning,filling,in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed , PCC in foundation of the mix (1:4:8) Type D-2 (using 40 mm graded crushed stone aggregate), PCC Pocing in PCC(1:2:4), type B0 using 12.5m crushed graded aggregate, brick masonry in cement mortar (1:4) rendering,12 mm thick in cement mortar (1:4) internally,finished even and fair and pointing flush externally as the work proceeds in the same mortar. Mild steel angle iron 50x50x6mm frame,MS sheet cover 3.15mm thick with handle and locking arrangment ,painting ,all the exposed MS work with two coats of synthetic enamel paint of tint as approved by the GE/AGE over a coats of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paint etc. complete all as specified and shown on drawing.

Construction of Valve pit of size 950cm x 950cm x 600cm (internal dimensions), Stone masonry construction,including all necessary excavation and earth work in hard/ dense soil,returning,filling,in disposal of surplus soil to a distance not exceeding 50 m and depositing where directed , PCC in foundation of the mix (1:4:8) Type D-2 (using 40 mm graded crushed stone aggregate), PCC Pocing in PCC(1:2:4), type B0 using 12.5m crushed graded aggregate, brick masonry in cement mortar (1:4) rendering,12 mm thick in cement mortar (1:4) internally,finished even and fair and pointing flush externally as the work proceeds in the same mortar. Mild steel angle iron 50x50x6mm frame,MS sheet cover 3.15mm thick with handle and locking arrangment ,painting ,all the exposed MS work with two coats of synthetic enamel paint of tint as approved by the GE/AGE over a coats of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paint etc. complete all as specified and shown on drawing.

Supply and fix 3 pole power contactors type ML 10, 250A AC-1, 200A AC- 3, 200A AC-4 rating 415V, 50Hz complete all as specified and directed. MAKE : L & T CAT Part No. SS90935 or equivalent make as specified in Appndx B to PS.

Supply and fix 3 pole power contactors type ML 6, 250A AC-1, 200A AC- 3, 200A AC-4 rating 415V, 50Hz complete all as specified and directed. MAKE : L & T CAT Part No. SS90933 or equivalent make as specified in Appndx B to PS.

Supply and fix water pipe line route indicator made of size 400 x 300 x 25mm of precast RCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate complete all as specified and directed. Note :- Route indicator should be written as main water supply line complete as directed by Engr-in-Charge.

M&L in repair sluice valves 100 mm dia bore of any size / make installed at water supply rising or distribution lines and incl dismantling and taking up or down of unserviceable SS / MS spindle and gun metal / bronze check nuts with replacement incl necessary rubber packing, nuts, bolts, washers etc and re-assembling in position after repair complete all as specified and directed by Engr-in-charge.

M&L in repair sluice valves 150 mm dia bore of any size / make installed at water supply rising or distribution lines and incl dismantling and taking up or down of unserviceable SS / MS spindle and gun metal / bronze check nuts with replacement incl necessary rubber packing, nuts, bolts, washers etc and re-assembling in position after repair complete all as specified and directed by Engr-in-charge.

M&L in repair sluice valves 200 mm dia bore of any size / make installed at water supply rising or distribution lines and incl dismantling and taking up or down of unserviceable SS / MS spindle and gun metal / bronze check nuts with replacement incl necessary rubber packing, nuts, bolts, washers etc and re-assembling in position after repair complete all as specified and directed by Engr-in-charge.

M&L in repair sluice valves 250 mm dia bore of any size / make installed at water supply rising or distribution lines and incl dismantling and taking up or down of unserviceable SS / MS spindle and gun metal / bronze check nuts with replacement incl necessary rubber packing, nuts, bolts, washers etc and re-assembling in position after repair complete all as specified and directed by Engr-in-charge.

M&L in repair sluice valves 300 mm dia bore of any size / make installed at water supply rising or distribution lines and incl dismantling and taking up or down of unserviceable SS / MS spindle and gun metal / bronze check nuts with replacement incl necessary rubber packing, nuts, bolts, washers etc and re-assembling in position after repair complete all as specified and directed by Engr-in-charge.

M&L for Galvanised iron wiremesh to Vent pipes, ventilators and entrance of OHT/UG sumps and providing clamps to pipes for fixing wiremesh to pipes duly painted with two coat of synthetic enamel paint over a coat of red oxide primer etc complete at various locations and directed.

S & F in replacement of cast iron sluice valve of 80 mm bore class PN-1.6 ISI marked (as per IS 14846 of 2000) heavy duty with flanged ends with high tensile SS spindle and gun metal check nut, iron hand wheel and fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost.

S & F in replacement of cast iron sluice valve of 100 mm bore class PN-1.6 ISI marked (as per IS 14846 of 2000) heavy duty with flanged ends with high tensile SS spindle and gun metal check nut, iron hand wheel and fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost.

S & F in replacement of cast iron sluice valve of 150 mm bore class PN-1.6 ISI marked (as per IS 14846 of 2000) heavy duty with flanged ends with high tensile SS spindle and gun metal check nut, iron hand wheel and fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost.

S & F in replacement of cast iron sluice valve of 250 mm bore class PN-1.6 ISI marked (as per IS 14846 of 2000) heavy duty with flanged ends with high tensile SS spindle and gun metal check nut, iron hand wheel and fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost.

S & F in replacement of cast iron sluice valve of 300 mm bore class PN-1.6 ISI marked (as per IS 14846 of 2000) heavy duty with flanged ends with high tensile SS spindle and gun metal check nut, iron hand wheel and fixing with providing suitable nuts, bolts, washers and rubber gasket for packing etc complete all as specified and directed.Note:- Any damage made to pipe lines, over head reservoir while replacing the sluice valve will be repaired by contractor on his own cost.

S & F in replacement of 80 mm bore non return valve both end flanged suitable for cast iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F in replacement of 100 mm bore non return valve both end flanged suitable for cast iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F in replacement of 150 mm bore non return valve both end flanged suitable for cast iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F in replacement cast iron foot valve of 100 mm size with flanged end IS-4038 including necessary rubber gasket, MS nuts, bolts, washers etc of suitable size complete all as specified and directed.

S & F in replacement cast iron foot valve of 150 mm size with flanged end IS-4038 including necessary rubber gasket, MS nuts, bolts, washers etc of suitable size complete all as specified and directed.

S & F in replacement of 50 mm bore air release valve double chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F in replacement of 100 mm bore air release valve double chamber as per IS 14845 including mounting GI pipe and clamps as per requirement at site suitable for cast iron pipe/ ductile iron pipe incl all fittings washer, nuts & bolt etc complete all as specified and directed.

S & F of ductile iron pipe fittings for spigot and socketed or flanged pipes i.e. bends, reducer, tail pieces, tapers, tees, caps etc of 80 mm to 300 mm bore pipe complete all as specified and as directed.

S & F cast iron fittings for spigot and socketed or flanged ends pipe i.e. bends, reducer, tail pieces, tapers, tees, caps and plugs with MS plate, nuts, bolts washers etc for size 80 to 300 mm bore complete all as specified and as directed.

S & F of change over switch with advanced neutral, ON LOAD, 630 Amps, 4 pole, AC 415 Volt, manual Change over insheet metal enclosure including operating handle conforming to IS:13947 (Part-3) complete all as specified and directed.

M & L for taking out unserviceable submersible motor for rewinding of submersible motors AC, 3 phase, 440 volt of capacity 5 to 15 HP with superior quality PVC insulated copper winding wire of identical gauge & specification of the existing short circuited winding wires with all necessary insulating materials incl cleaning of stator & slots and applying one coat of water proof epoxy paint to the exteriors of motor and testing on load complete all as directed and specified Note:-(i) Contractor will be intimated on phone followed by in writing to repair the unserviceablepump motor. Contractor or his rep has to attend the installation within same day . The unserviceable pump mtor will have to be repaired within 3 days after intimation to contractor failing which a panel recovery of Rs 2000/- per day per motor will be deducted from his dues /payments . (ii) Cost for all machinary T&P/transport to workshop and menpower for the work will be deemed for included in unit rate.

Discription as per item No 30 here in before but induction motor of 15 to 30 HP capacity 3 phase AC, 440Volts complete all as specified and as directed.

Discription as per item No 30 here in before but induction motor of 40 to 50 HP capacity 3 phase AC, 440Volts complete all as specified and as directed.

Discription as per item No 30 here in before but induction motor of 60 to 75 HP capacity 3 phase AC, 440Volts complete all as specified and as directed.

Discription as per item No 30 here in before but induction motor of 90 to 100 HP capacity 3 phase AC, 440Volts complete all as specified and as directed.

S&F terminal connector of 5 to 30HP motor with high tensile brass bolts and nuts, washer etc complete all as specified and as directed.

S&F terminal connector of 40 to 100HP motor with high tensile brass bolts and nuts, washer etc complete all as specified and as directed.

S & F of PVC fan blade for motors of 5 to 15 HP capacity complete all as specified and as directed.

S & F MS pump motor coupling of 15 HP to 30 HP as per the existing size and shape for pump sets complete all as specified and as directed.

S & F MS pump motor coupling of 40 HP to 100 HP as per the existing size and shape for pump sets complete all as specified and as directed.

M & L for motor end ball / roller bearing with good quality grease suitable for 5 HP to 15HP capacity pump sets complete all as specified and as directed.

M & L for motor end ball / roller bearing with good quality grease suitable for 15 to 40 HP capacity pump sets complete all as specified and as directed.

M & L for motor end ball / roller bearing with good quality grease suitable for 60 to 100 HP capacity pump sets complete all as specified and as directed.

S & F rubber bush/belt coupling (set of 8) for motor 15 to 30HP complete all as specified and directed.

S & F rubber bush/belt coupling (set of 8) for motor 40 HP to 60HP complete all as specified and directed.

S & F rubber bush/belt coupling (set of 8) for motor 90 to 100 HP complete all as specified and directed.

M & L for dismantling and taking up/down u/s centrifugal pump sets of any capacity of any size from foundations/pumphouse after disconnecting electric & water connections and transportation from site to contractor's workshop for carrying out repairs to pump sets , replacement of unserviceable parts as required incl re-assembling, re-fixing in position, including connecting in original position & testing complete as directed and specified . Note - (i) Spares required to be replaced will be measured and paid separately. (ii) Intimation for any unserviceable pump of any capacity mentioned here under relevent items will be given to contractor or his accredited representative/superviser via telephone or followed by in writing . The unserviceable motor or pump will have to be repaired , re-installed in and made functional without anyt defect within a period of 96 hrs after intimation to contractor failing which a panel recovery @ Rs. 100/- per hour for delay period will be initiated and deducted from contractor's payments /RAR/Final bill etc . Contractor have to quote his rates accordingly and no claim whatsoever shall be entertained in this regard . (iii) Costs of all necessary T&P required at site and transportation is deemed to be included in the rates quoted.

Supply and fix coupling key any size as per sample for pumping sets of different capacities complete all as directed and specified

M&L for carrying out replacement of u/s shaft suitable for centrifugal pump 5 HP to 15 HP capacity complete all as directed and specified

M&L for carrying out replacement of u/s shaft suitable for centrifugal pump 15 to 30 HP capacity complete all as directed and specified

M&L for carrying out replacement of u/s shaft suitable for centrifugal pump 40 HP to 60 HP capacity complete all as directed and specified

M&L for carrying out replacement of u/s shaft suitable for centrifugal pump 90 to 100 HP capacitycomplete all as directed and specified

M & L for carrying out replacement of pump impeller of 5 HP to 7.5 HP capacity complete all as directed and specified

M & L for carrying out replacement of pump impeller of 10 HP to 30 HP capacity complete all as directed and specified

S & F in replacement of gun metal bush complete set of two as per sample for centrifugal pump set 15 HP to 30 HP complete all as directed and specified

S & F in replacement of gun metal bush complete set of two as per sample for centrifugal pump set 40 HP of 100 HP complete all as directed and specified

S & F in replacement of gun metal sleeve set of two Nos suitable for pump sets 15 HP to 30 HP complete all as directed and specified

S & F in replacement of gun metal sleeve set of two Nos suitable for pump sets 40 HP to 60 HP complete all as directed and specified

S & F in replacement of gun metal sleeve set of two Nos suitable for pump sets 90HP to100 HP complete all as directed and specified

S & F in replacement of pump end ball bearing suitable for 15 HP To 30 HP complete all as directed and specified

S & F in replacement of pump end ball bearing suitable for 40 HP to 60 HP complete all as directed and specified

S & F in replacement of pump end ball bearing suitable for pump sets 90HP to100 HP. complete all as directed and specified

S & F GM neck rings (set of 2) as per sample suitable for centrifugal pump set 15 HP to 30 HP capacity complete all as directed and specified

S & F GM neck rings (set of 2) as per sample suitable for centrifugal pump set 40 HP to 60 HP capacity complete all as directed and specified

S & F GM neck rings (set of 2) as per sample suitable for centrifugal pump set 100 HP capacity complete all as directed and specified

S & F in replacement gun metal impeller single acting suitable for 15 HP capacity. complete all as directed and specified

S & F in replacement gun metal impeller single acting suitable for 30 HP capacity complete all as directed and specified

S & F in replacement gun metal impeller single acting suitable for 40 HP capacity.complete all as directed and specified

S & F in replacement gun metal impeller single acting suitable for 60 HP capacity complete all as directed and specified

S & F in replacement gun metal impeller single acting suitable for 100 HP capacity complete all as directed and specified

S & F in replacement of digital soft starter suitable for 40 to 60 HP motor, 3 phase 415 volt with comprehensive motor protection, programmable over load protection, built-in RTD & Thermistor inputs with constant current adaptive accelaration & de-accelaration for smooth start and stop operation of motor incl dismantling of u/s starter & installation / programming by skilled technician of original manufacturer, incl necessary mounting arrangement on existing panel such as fastener nuts & bolts and also fixing HRC fuse of suitable capacity on panels with copper busbars etc as required complete all as specified and directed. Make:- L&T Cat No EMX4i-0135B-511 or any equivalent models of approved make

S & F in replacement of digital soft starter suitable for 90 to 100 HP motor, 3 phase 415 volt with comprehensive motor protection, programmable over load protection, built-in RTD & Thermistor inputs with constant current adaptive accelaration & de-accelaration for smooth start and stop operation of motor incl dismantling of u/s starter & installation / programming by skilled technician of original manufacturer, incl necessary mounting arrangement on existing panel such as fastener nuts & bolts and also fixing HRC fuse of suitable capacity on panels with copper busbars etc as required complete all as specified and directed. Make:- L&T Cat No EMX4i or any equivalent models of approved make

Supply and laying in tenches/pipes/along wall/roof/across drain/culvert XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 4 core. Make : KEI/Plaza/Havells/Polycab or equivalent.

Supply and laying in tenches/pipes/along wall/roof/across drain/culvert XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade, cross sectional area 25 Sqmm 3.5 core. Make : KEI/Plaza/Havells/Polycab or equivalent.

Taking down existing vintage HPSV/CFL/ LED type security Light fitting at pump house area and replacing the same with Energy efficient LED type Bldg security light fitting Pressure die cast aluminium housing with heat resistant toughened glass & IP66 protection 45 watts(with lens)with Luminous Efficacy more than 100 Lm and Power Factor not less than 0.95 all as specified and directed .Make:- HAVELLS CAT PART NO:-LHETAXU7PN6J045.

M&L for GI bracket made out of 40mm dia GI pipe light grade 1.20 mtr long bend to shape or size as directed at site for mounting street light complete all as specified and directed.

M&L for river sand cushioning of LT UG cable including spreading, levelling, well ramming in layers not exceeding 1.5 mtr in depth complete all as specified and directed.

M&L for cable cover Class LV, Type I, flat, size 250mm x 150mm x 40mm size for cable protection in trenches all as specified and directed.

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr depth and getting out for laying of pipe lines in any type of soil complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 Cm each in soil complete all as specified and as directed.

Removal of surplus soil to a distance not exceeding 50 Mtrs and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and as directed.

M & L for cutting of stone block pavement/road a depth up to 1.5 mtr below the normal ground level and in width equal to external dia plus 300 mm for lay pipe line upto 300 mm dia across the road in horizontal position and making good the cut portion filled with PCC 1:3:6 type C-2 using 40 mm graded stone aggregates 450 mm thick from TOP over 300 mm thick hard core over filled earth to levelled with existing surfaces for smooth plying of vehicles etc complete all as specified and directed. The repaired portion will be match to the existing surface. Note : Cost of PCC ,hard core,stones and Earth shall deemed to be included in unit rate quoted by the tendered.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in foundations/foot path etc complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness below or above ground level including removal of debris complete all as specified and directed

M&L for taking up or down GI water tubing and connections of 15 mm dia including cleaning for refixing complete all as specified and directed.

M&L for taking up or down GI water tubing and connections of 20 mm dia including cleaning for refixing complete all as specified and directed.

M&L for taking up or down GI water tubing and connections of 25 mm dia including cleaning for refixing complete all as specified and directed.

M&L for taking up or down GI water tubing and connections of 40 mm dia including cleaning for refixing complete all as specified and directed.

M&L for taking up or down GI water tubing and connections of 50 mm dia including cleaning for refixing complete all as specified and directed.

M&L for taking up or down GI water tubing and connections of 80 mm dia including cleaning for refixing complete all as specified and directed.

M&L for taking up or down GI water tubing and connections of 100 mm dia including cleaning for refixing complete all as specified and directed.

Re-laying / re-fixing galvanised mild steel water tubing of 15 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Re-laying / re-fixing galvanised mild steel water tubing of 20 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Re-laying / re-fixing galvanised mild steel water tubing of 25 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Re-laying / re-fixing galvanised mild steel water tubing of 40 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Re-laying / re-fixing galvanised mild steel water tubing of 50 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Re-laying / re-fixing galvanised mild steel water tubing of 80 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

Re-laying / re-fixing galvanised mild steel water tubing of 100 mm bore with and including all fittings laid in trenches, under floor or fixed to walls / ceilings complete all as specified and as directed.

S & F galvanised steel water tubing medium grade 15 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F galvanised steel water tubing medium grade 20 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F galvanised steel water tubing medium grade 25 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F galvanised steel water tubing medium grade 40 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F galvanised steel water tubing medium grade 50 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F galvanised steel water tubing medium grade 80 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F galvanised steel water tubing medium grade 100 mm bore with all fittings such as bends, elbow, socket etc laid under floors/trenches or on walls with fixing arrangments including leakage testing complete all as specified and directed.

S & F in replacement of brass ball valves of size 15 mm bore ISI marked with iron wheel head, screwed both ends for iron pipe incl dismantling old U/S gate valves all as specified and directed

S & F in replacement of brass ball valves of size 20 mm bore ISI marked with iron wheel head, screwed both ends for iron pipe incl dismantling old U/S gate valves all as specified and directed

S & F in replacement of brass ball valves of size 25 mm bore ISI marked with iron wheel head, screwed both ends for iron pipe incl dismantling old U/S gate valves all as specified and directed

S & F in replacement of brass ball valves of size 40 mm bore ISI marked with iron wheel head, screwed both ends for iron pipe incl dismantling old U/S gate valves all as specified and directed

S & F in replacement of brass ball valves of size 50 mm bore ISI marked with iron wheel head, screwed both ends for iron pipe incl dismantling old U/S gate valves all as specified and directed

M&L for boring on existing GI/CI/DI pipe upto 300 mm bore for branch connections of 25 to 50 mm bore by fixing of MS clamp 100 x 4 mm cut to length and bend to shape, drilled and welded with GI socket of suitable size including rubber packing, nut, bolt etc and testing complete all as specified.

M & L for cutting of GI/DI/CI pipe 80 to 250 mm bore carefully for inserting fittings such as bend, tee, socket pieces, collar etc complete all as specified and as directed.

M&L for taking up or down CI/DI water mains with spigot and socket ends and lead joints including of size 100 bore including all fittings and connections including burning of joints and recovering leads and cleaning thoroughly for re-routing / improvement of pipe line complete all as specified and directed by Engr-in-Charge.

M&L for taking up or down CI/DI water mains with spigot and socket ends and lead joints including of size 150 bore including all fittings and connections including burning of joints and recovering leads and cleaning thoroughly for re-routing / improvement of pipe line complete all as specified and directed by Engr-in-Charge.

M&L for taking up or down CI/DI water mains with spigot and socket ends and lead joints including of size 200 bore including all fittings and connections including burning of joints and recovering leads and cleaning thoroughly for re-routing / improvement of pipe line complete all as specified and directed by Engr-in-Charge.

S & F in replacement ductile iron pipe with socket and spigot ends of 100 mm bore class - K-9 , with ceramic epoxy lining /coating inside and external zinc coating with a bitumen finishing layer , ISI maked IS - 8329-2000 (Reaffiremed - 2005 Edition 4.1) suitable for "push on joints" in any lengths and including providing joints (Tyton joints) including taking out from vertical position or from trenches etc complete all as specified.Make : Electro steel /Jindal /Kejriwal Note for item No 115 to 120 : The cost of joints shall deemed to be included in unit rate quoted by the tenderer. (Excavation and earth work shall be measured and paid seperately.)

Discription as per item No 115 here in before but 150 mm bore

Discription as per item No 115 here in before but 200 mm bore

M&L for relaying/refixing, jointing and testing of ductile iron pipe of 100 mm bore all as specified and directed by Engr-in-Charge. Note :- Cost of all jointing materials required at site like rubber ring joint included in the quoted rate, earthwork shall be measured and paid separately.

Discription as per item No 118 above but 150 mm bore

Discription as per item No 118 above but 200 mm bore

M&L for Painting to water pipelines of any size and type with two coat of Synthetic enamel paint as directed by Engineer in charge painting with approved quality and colour after cleaning and removing the rusted area using sand paper complete all as specified and directed.

M&L for earthing complete including necessary excavation and earth work in any type of soil with galvanized steel earth plate electrode size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to galvanised earth strip 32x6 mm by means of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate No.5 of MES SSR Part-1 connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by galvanised iron 40 mm dia. light grade pipe and watering pipe shall be 20 mm ore medium grade PCC pipt with pre cast RCC cover, charcoal/salt funnel etc. complete all as directed. Note : The conctrete pit shall be PCC 1:3:6 type C1, 40 mm thick pre-cast cover slab of RCC (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 8 mm TMT bars @10 cm C/C on both sides with suitable cast iron handle shall be provided in liew of cast iron cover shown in electrical plate No.5 of MES SSR Part-1 (ii) Item includes the cost of 7.5 m GI pipe for protectio of earth strip. (iii) PCC pits shall be provided atleast 500 mm away from the pit and not on the earth pit itself and the extra cost of additional length of watering pipe, bends , elbows etc. shall be deemed to be included in the quioted rate. (iv) Item includes the cost of 7.5 mtr length earth strip.

Supply installation ,commissioning and testing of LT panel indoor type,floor mounted,weather vermin proof factory made,CPRI approved,facricated out of 3mm thick mild steel sheet mounted ,on frame of mild steel angle iron 50mm X 50mm X 6mm ,45 CM above the ground level duly supported with mild steel angle iron 50mm X 50mm X 6 mm thick in PCC fondation (1:2:4) ,type B-1,Using 20mm graded crushed stone aggregate ,LT panel shall be totally enclosed with front double door and rear opening with IP-54 protection as per IS/8623 duly powder coated for 433 volts,3 phase ,4 wire having TPN Aluminium bus bars suitable for 400 Amp load incommer, duly drilled holes for connection ,RYB insulated with different colour code and sleeved insulators complted prewired and cable connection with copper conductor wire upto copper bus bars including all incoming and outgoing cable connection with suitable size of copper lugs/gland complete all as specified and directed by Engr-in-Chrge and also comprissing of following:-

INCOMING: (i) MCCB 4P,415V ,400 Amps 36KA breaking capacity with ics=100% icu and termal adjustable setting-01 Nos (ii) Phase indication light & control uses-01 Nos (iii) Aluminium bas bar 3 phase and neutral , 4 strip suitable for 600 Amp current carring capacity complete with post insulators and heat shrinkable sleeves. OUTGOING:(i) MCCB 4P,415V ,160 Amps 25KA breaking capacity with ics=100% icu and termal adjustable setting-02 Nos(ii) Phase indication with led lamp(RYB)& control fuses set of three -02Nos(iii) Bus bar chamber with and including Aluminium Strip (4 Nos) suitable for 400 Amp duly insulated,wired & duly mounted on porcelain insulators (iv) Multifuction digital meter CT operated suitable for showing voltage current ,HZ,KW,KWH etc (v) Cosmic star fully automatic star delta starter (FASD) suitable for 30HP to 40HP motor including overload relays, under voltage relay, single phase preventer & phase Corrector- 02 Nos

Supply & Fixing signs board, signs printed on Photoluminiser U 1000 aluminium sheet of 1 mm thickness containing lumigen 3 III on base chemical covered under UV stabilized coating of 30 x 20 cm size including fixing arrangement/ hanging with steel chain from top/roof/ wall etc with proper clamps/ cleats/ anchor fasteners etc in all respects.

M&L for providing and fixing stainless steel (Grade 304) railing/sign board made of hollow tubes/ rectangular/square as per site requirement, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (where ever required and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the ralling with necessary accessories & Stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

S&F Retro reflective sign board made up with 1.2mm thick stainless steel sheet of which both faces shall be fully covered with high intensity prismatic(HIP) retro reflactive sheeting of approved specification as MORT having approved massage (Matter and Base) fully processed by pressure sensetive equipment of approved brand (Avery Dennison/3M) fixed on stainless steel frame made up of SS as described in the item No 18.00 specification complete all as specified and directed.

S&F Framed work as in doors, gates or sign board of angle or other section with gusset plates, ralls, [braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides and hanging; also fastening and fixing complete all as specified and directed.

S&F for for stainless steel letter (3 dimension) mirror finish for outdoor (height min 104) and width of letter is (3" to 12" as per reqd). The letter are fixed in ACP sheet sign board with using of adhesive paste/ screw and bolt properly in any position complete all as specified and directed by Engineer-in-Charge. Note:- (i)The design of letter, colour, thickness and size shall be approved by Engineer-in-Charge. (ii) Using of T&P etc to be included in this Item. (iii) Dismantling and refixing of sign board in same place to be included in this items.

S&F in repair for ACP background sheet for thickness (3mm to 4mm ) and fixed in angle and other section frame in any position specifications complete all as specified and directed. (i) The design of each board, size,shape,colour, thickness shall be approved by Engineer-in-Charge. (ii) Using of T&P etc to be included in this item. (iii) Frame work and paint work shall be measured and paid separately.

M & L for cleaning of RCC overhead reservoir of 25000 gallon capacity, staging of 17 to 21 mtr. Dewatering, taking out all deposits sludge / mud incl scrubbing/brushing to remove all funges growth inside the entire interior surface of the reservoir and washing thoroughly after cleaning with bleaching powder and making ready for use including writing of date of cleaning with existing colour and after that painting complete outside surface of OHT/ reservoir/ UG sump with one coat of distempering complete all as specified and directed by Engr-in-Charge. Note : 1. Rate for dewatering cleaning & painting (inside & outside) of UG sump/semi UG sump by using of diesel engine pump set is deemed to be included in the quoted rate. 2. All necessary T & P required for cleaning OHT/UG sump is deemed to de included in unit rate quoted. 3. All necessary safty precaution to be taken by contractor while cleaning to avoid any accident any laps on this part contractor will be responsible for any lops.

Discription as per item No 131 here in before but of 50000 gallon capacity

Discription as per item No 131 here in before but of 100000 gallon capacity

Discription as per item No 131 here in before but of 150000 gallon capacity

Discription as per item No 131 above but U/G sump 25000 to 50000 gallon capacity

Discription as per item No 131 above but U/G sump 300000 to 4000000 gallon capacity

M & L for cleaning of shallow wells of any depth dewatering by using diesel engine pump set and taking out of mud/silt/vegetation etc manually upto 1 mtr from exisitng bed of well & removal of the same away from MOD land complete all as specified and as directed by Engr-in-Charge. Note : 1. Rate for dewatering shallow wells by using of diesel engine pump set is deemed to be included in the quoted rate. 2. All necessary T & P required for cleaning OHT/UG sump is deemed to de included in unit rate quoted. 3. All necessary safty precaution to be taken by contractor while cleaning to avoid any accident any laps on this part contractor will be responsible for any lops.

M & L for chemical and bacteriological testing of water samples of shallow wells from Jal Nigam laboratory / any govt institution complete all as specified and directed. Note - The material and transportation for collection of samples quoted in the rate. The report will deposited to office after completion of test from the laboratory.

M&L for painting with two coats of synthetic enamel paint and re-writing the same description with colour of sign board, rising and distribution pipe line from semi UG sump to pump house, black colour paint on valve pit cover, valves, UG sump details on sump etc within the installation including preparation of old/existing surface, rubbing and removing rust, worn out old paint layers and other foreigh materials complete all as specified and directed.

M&L for repair of leakage/damage/defect in raising main through taking down the MS/GI pipe for ground level to OHT work after dismantling flange joints and including replacement of gaskeet /MS flang of same size if required and refixing the pipe on its original position vertially or horigentally of raising/supply line of OHT flanged type from ground level to top of the OHT of size 150 mm dia . The rate includes the dismantling of existing CI pipe of flanged type, sluice valve size as per fixed at OHT and for providing & welding of flanges on the pipes all as required and directed by the enginer in Charge. The contractor also ensure that the job will complete with in 24 hours to ensure the restoration of supply as directed.The quantity of water supply pipe and sluice valve laid/fitted will be measured and paid separately. Note:- The cost of taking down/dismantling any type of valves/flanges ect is deemed to be in included herein unit rate. the rate also included cost of necessary T & P man power required at site.

All as per Srl item No. 140 here-in-before but 200 mm dia.

All as per Srl item No. 140 here-in-before but 250 mm dia.

S&F in reapir water level indicator for OHT's at different locations made of level indicaton scale on 2 mm thick MS sheet duly painted with synthetic enamel paint over a coat of red oxide primer and fixing of level indication scale at hight of 3 mtr from ground level. The level indicator must be at height of 3 mtr and 30 mm width made of materail as per existing . Level indicator includes floating ball, guage wire from inside tank to level indicating board. The guage wire must be made with multistranded SWR of thickness 3 mm dia. SWR shall run over pulleys and pulleys fixed on wall where directed .Note: The rate includes for providing and fixing pulley of suitable size /dia .(ii) Mild steel shall be measured and paid seperately.

Supply only Nylon braided PVC flexible pipe, heavy duty 20 mm dia.all as per sample complete all as specified and as directed.

Supply only Chlorine test kit with coloured sample complete with all testing fitments and 100 ml OT solution in rexine finish wooden box all as per sample.Make:-Aquajio technologies or equilent approved make

Supply only Ortho tholodine solution in 500 ml bottle.

Supply only Crystal Alum (Ferric)

Supply only Copper Sulphate

S&F in replacement PVC flexible corrugated pipe of size 50mm bore for suction sweeper as per sample complete all as directed and specified.

M/S Kharya Associates

M/S ARVIND SINGH THEKEDAR

M/s BRIJ KUMAR RAI