CERTAIN REPAIR/MAINT TO MD/FAFA ACCN IN AREA A-2 OF AGE B/R-I UNDER GE (W) JALANDHAR CANTT

Amount

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete

Demolition of brick or stone masonary built in cement mortar complete

Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc

M&L brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6.

M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed

M&L Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring, hard standing,Manhole, drain etc.

M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls.

M&L machine pressed precast coloured concrete coloured interlocking paver blocks any shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment.

M & L for 25mm thick Sand filling under floors or in foundations including watering and consolidation

M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in kerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work.

M&L 10mm thick rendering in CM 1:3 on brick/concrete surface as in ceiling and finishing the surface even and smooth with out using extra cement.

M&L 15mm thick rendering on wall in CM 1:4 with appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface,finished even and smooth without using extra cement.

M&L 15mm thick rendering on wall in CM 1:6 with appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface and finishing the surface even and smooth with out using extra cement.

Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4.

M/L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6.

Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6.

Demolition of re-inforced cement concrete of any description and in any position not otherwise specifically provided for

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete

M L for Reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) (nominal mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

M&L for green marble (of any type)work 18 to 20 mm thick (table rubbed and polished) as in steps, cooking plat forms and the like,in cement mortar1 : 4 including painting in white cement (1 : 2) using marble dust with admixture of pigment to match with shade of green marble etc, incl roughening of surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and 15mm thich screed bed in CM 1:6.

Rounding/moulding to edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform, and other similar situations etc

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified.

Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd.

M&L for PCC pedding with cement concrete type B-1, 1:2:4 (using 12.50mm graded stone aggregate) to top surface of slab in slop 1:40,finishing the surface even and smooth without using extra cement comlete all as specified.

M & L applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 Kg per Sqm over applying primer bitumen coat @0.30 kg per Sqm including cleaning surfaces on roof top.

M&L APP based polymeric membrance minimum weight not less than 3.0kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/Sqm) land on primed surface by forced application(Complete surface sealed by gas flame) with over lap of 15 cm complete all as specified and directed complete all as spd and directed.

M & L 40mm th. Brick tiles laid on bedding layer of CM 1;3,15mm thick and joints grouted flush in cement mortar 1:6 mixed with 5% of crude oil by weight ofcement over APP membrane

Fixing only 40mm th. Brick tiles laid on laid on bedding layer of CM 1;3 15mm thick joints grouted flush in cement mortar 1:6 mixed with 5% of crude oil by weight of cement on APP (except tiles)

Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5Sqm each

Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5Sqm n.exc 4 Sqm each

Taking down shutters any description exc 1 Sqm but n.exc 2Sqm each and all as specified and directed

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm

M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick

S&F 2nd class hardwood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats.

S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mited and rebated bars any numbers.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply, and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickenss. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by insering horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineerin-charge

S & F 25mm thick flush shutters, solid core construction, with block board core and plywood face panels, comercial type on both side.

Dismantling of unframed timber scantlings in fillets, rails, posts, rafters, purlins,etc. under 40 sq. cm in section in any position

S & F Second class hard-wood in scantlings clean swan for holding of shelf to Cup board/ward robe etc as directed by Engr in Charge.

Dismantling boarding, any description, fixed in any position with nails

S & F 25mm Boarding, fixed with nails in any situation Planed one side with butt joints in repair to wardrobe,Cup board as directed by Engr in Charge.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

Steel window/ventilator 1.25 mm thick Box type ERW hollow P section of size 60mm x 25 mm single rebated comprises skelton shutter ERW Sec 50 MM x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T-section 20 mm x 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1, including shop coat primer and following fittings welded to shutters:-i) Hold fasts 150 mm long,12mm x 3mm made to shape -04 No’s, (ii) Handle of Z sec 20mm x 25mm , 100mm long per leaf -1 No’s (iii) MS tower bolt 150 mm long per leaf -2 No’s (iv) Z sec 20mm x 25 mm , 100 mm long stopper per leaf -1 No (v) Cleat 55 mm long of hollow square 15mm x 20mm x 63 mm welded to hinges per leaf -01 No (vi) MS pintal hinges of size 75mm x 12 mm per leaf -02 Nos (vii) Fabrication and fixing arrangement complete Makes/Manufactures:- M/sTee Pee Enterprises Amritsar, M/S Ram fabricators Pvt Ltd Punchkula.

Ditto as per description of item No 51 above but glazed shutter.

S & F powder coated of any colour (Thickness or powder coating not less than 50 micron) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

M & L Powder coated aluminium (minimum thickness of powder coating 50 micron) for sliding window shutters including frame ,providing and fixing roller, three track system, locking arrangement fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws where necessary all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde - 165.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified.

S&F Butt hinges, medium weight cold rolled mild steel 100 mm size ISI marked.

S & F for Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified

S&F Extruded aluminium alloy handles fabricated type anodised 150mm size

S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified.

S & F for 100mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws

S & F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls

S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed.

Refixing 15mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.)

S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed.

Refixing 20 mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.)

Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittings complete.

S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I

S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair

S&F ball float valve PTMT with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe.

S&Fin repair 15mm dia Bib taps cast copper alloywith fancy type chromium plated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule

S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs.

S&F 15mm dia stop valves/angle valve chromium plated, fancy type with long shank and cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified.

S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets &32mm waste cuppling complete all as specifed and directed.

S&F in repair 15mm dia fancy type swan neck pillar taps cast copper alloy with capstan heads chromium plated scewed down high pressure with long scrwed shanks and fly nuts screwed for iron pipes

S&F in repair 15mm brass CP bath mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repair 15mm brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in replacement CP Jet for EWC including flexible pipe complete all as specified.

S&F in repair Vitreous China Water closet (Squatting pattern) "Orissa Pattern" size 580x 440 mm white with 'P' or 'S' trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) complete.

S&F Vitreous China wash down Water closet pan (pedestal pattern) "with plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairs completee

S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs

S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified

S&F in replacement CP grating 125mm dia circular of approved make and fixing with cement mortar 1:3 on Nahani Trap or floor trap complete all as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Dismantling of cast iron or reinforced concrete drain pipes of size 100mm dia, jointed in cement mortar and taking out of trenches, if required.

M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls

S&F110mm PVC (SWR) bends

S&F75 mm PVC (SWR) bends

S&F brass chromium plated shower rose 125mm size complete all as spd and directed.

Supply in fixing in repairs sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

M & L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying one coat of synthetic enamelled paint including preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying two coat of synthetic enamelled paint over one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying white wash of two coats as in ceiling incl preparation newly plastered surfaces as specified and directed.

M & L for applying white wash of one coats as in ceiling incl preparation old painted surfaces as specified and directed.

Complete removal of existing treatment on wall and applying Two coat of white wash incl preparation old plastered surfaces as specified and directed.

M&L for prepration of old surfaces of walls and applying one coat of white (lime) wash on wall complete all as specified and directed by Engr -in-charge.

Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper complete all as specified.

Material and labour for preparation of old painted surfaces on walls and applying one coats of oil distemper complete all as specified.

Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paint complete all as specified.

Material and labour for preparation of old painted surfaces on walls and applying one coats of cement base paint complete all as specified.

aditi construction co. (BID ID -3443140)

KMTR MONCHER COLLECTION PRIVATE LIMITED (BID ID -3449884)