COMPREHENSIVE B/R REPAIRS AND PERIODICAL WORK INCLUDING PLASTERING, TILING, PLINTH PROTECTION, SANITARY FITTINGS AND OTHER CONNECTED WORK IN OFFRS MD ACCN INCLUDING OTM ACCN OF ZONE C OF SOUTH AREA UNDER AGE B/R II AT NASIRABAD

Amount

Taking down cement plastering of any description on brick / stone/ concrete wall / ceiling surfaces of any description incl racking out joints hacking for key, scrubbing down with water etc.

Dismantling floor, hearth or wall tiles, including cement mortar, removing serviceable tiles from site & rubbish off the premises, complete all as specified and directed.

Demolition of brick or stone Masonary built in cement mortar etc complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in ground floors and pavings n. exc 15cm thickness (below or above ground level).

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frame) including dismantling of PCC bed blocks for hold fasts.

Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.

Taking down shutters of any description exc 1.0sqm and n. exc 2.00 sqm each shutter complete all as specified and directed.

M&L for rendering in cement mortar (1:6), 15mm thick on other than fair faces of stone masonary surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar in CM (1:3) on ceiling finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:4) mixed with water proofing compound @3% by weight of cement on fair faces of brick work or concrete surfaces, finished even and smooth complete all as specified and directed. Note :- WPC measured and paid separately

M&L for rough cast plaster mix with crushed stone (6-10 mm) sand and cement in the ratio 1:1:1 over 15 mm thick rendering CM 1:4 etc complete all as spd and directed by Engr-in-Charge.

M&L for walling of random rubble masonary uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:6 etc complete all as specified and directed.

M&L for old size brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for old size brick work with fly ash bricks, straight or curved on plan exc 6M mean radius built in cement mortar 1:6 complete all as specified and directed.

Dismantling loose /disintegrated portion of RCC Chajjas, bend shelves, beams balconies and similar work at any position or any height and dobbing out with PCC 1:1.5:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished required shape including applying anti corrosive paint on exposed surfaces of reinforcement and provision of necessary supporting form work and including 10mm thick plastering in CM 1:4, finished fair and even, complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded stone aggregate as in floors complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but not exc 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bedding in cement mortar 1:6, complete all as specified and directed.

M&L for vitrified ceramic tiles light shade8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm but not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 sqm, in vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed plaster 10mm thick in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles 7 to 8 mm thick in vertical surfaces area of each tile of exc. 0.11 Sqm and but not exc. 0.18 Sqm set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window -cills, cooking platforms and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl rounding of edge laid over 15mm thick screed bed in CM (1:6) including rounding of edges of stone slabs one edge, complete all as specified and directed.

M&L for rolled mild steel work as in door frame (chowkhats) including provn of 10mm dia deformed bar welded horizontally to bottom of frame conforming to Fe-290 (Gde 165-E) including preparing back of chowkhat and applying two coats tar and sanding newly tarred surfaces with clean sharp sand complete all as specified and directed.

S&F plain, solid, straight chowkats in 2nd class hard wood and framed rebates on the solid rounded or chamfered put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement.

M&L for raking out joint /pointing to random rubble or polygonal rubble stone masonary uncoursed or brought upto courses built in cement mortar and M&L for raised pointing in cement mortar (1:4) complete all as specified and directed.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, paneled shutter (Two/Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F 35mm thick 2nd class HW glazed and skeleton shutters open rebated and prepared to receive glass/wire cloth gauge etc,(without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR part I, sectiion 8, clause 8.24(a) complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm prelam coloured PVC sheet using instead of plain colour PVC sheet & edges will be painted to match with prelam sheet as reinforced with MS square tube and fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC moulded door shutter with wood free EPS, 28to30mm thick, (styles) with 2,4 or 6 raised panel design with 2mm thick moulded Prelam (Nut Brown Colour )PVC sheet on the front face & 2mm Prelam (Nut Brown colour ) PVC sheet on back face, and fixing in the frame at site as per specification and drawings on page 176 to 181 of SSR (Part -II) 2020 complete all as specified and directed.

S & F in repair Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including two coats synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

Supply and fixing in repairs 18/19mm thick prelaminated partcile board, exterior grade, prelaminated both sides with decorative choice laminations, fixed with screws, including teak wood lipping 19x6mm thick fixed with nails in shelves, partition and pelmet boxes, cupboard shelves etc all as specified and directed.

S & F continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 40 mm all as specified and directed.

S & F 100mm size hasp and staple, aluminium anodised safety type, fixed with screws complete all as specified and directed

S&F Aluminium anodised sliding door bolts of size 300mm long, with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F MS butt hinges, medium weigh, cold rolled, ISI marked of size 125mm, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section ISI marked all as specified and directed.

S&F 150mm long extrueded aluminium alloy handles, fabricated type, anodised ISI marked complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperature 1.40mm and fixed tinned or stainless steel wire staple complete all as specified and directed.

S & F in repairs 100 mm long dual leg door stopper of alumunium alloy body fixing on door, complete all as specified.

S&F in repairs, 25mm dia stainless steel curtain rod heavy duty with a pair of decorative Curtain Finials/ knob & heavy Curtain Support Bracket for rod made of stainless steel, etc. complete all as specified & directed.

S&F in repairs Vitreous China, Squatting pan Orissa pattern size 580X440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe and making good the floor to match the existing complete all as specified & directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe ) and to flushing pipe anti syphonage pipe etc complete all as specified and directed

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

Demolition of cement concrete of any description from sunken floor (ground or Ist floor) and removing and depositing materials exc 50 mtrs depositing level n.exc. 1.5 m above the starting point complete all as specified and directed.

M&L for mass concrete filling using PCC (1:5:10) type E2 in sunken floor complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:3 on fair faces of brick work, concrete surfaces as in sunken / roof treatment finished even and smooth without using extra cement with and including applying two coats of acrylic polymer treatment as per manufacture complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

S&F in repairs PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity, White, with inlet ball valve, float and handle fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified & directed.

S&F in repair CP brass shower rose with or without swivel joints 100mm size including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts and bolts of length 450mm etc complete all as specified and directed

S&F in repair angle valves 15mm bore , cast copper alloy chromium plated, ISI Marked, screwed down high pressure screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F in repairs grating round/Square 125mm dia PTMT minimum weight 50 gms fixed to Floor trap/Nahani trap with CM 1:6 etc complete all as specified and directed.

S&F in repair stainless steel sinks with draining board made of 1mm thick sheet with over all size 915mm x 460mm and bowl size 410mmx330x160mm for kitchen or laboratory with plug washers and waste pipe and CP Union, including bedding in cement mortar on to dwarf walls or including fixing centilever bracket and connecting uinon to waste pipe complete all as specified and directed. Note :- Minor variation in dimension + 20mm as per standard catalogue of manufacturer may be approval of GE in writing without price adjustment.

S & F in repairs stainless steel plate rack made of 0.50mm thick of over all size 914mm x 609 mm and weight not less than 7.00 Kg each of approved quality fixed with rawl plug and CP steel screws all as directed. Note :- Minor variation in dimension may be permitted as per standard manufacturing models of manufacturer without price adjustment with prior approval of GE but weight shall not be less than 7.00 Kgs.

S&F in repairs 15mm bore cast copper alloy chromium plated bib tap ISI Marked with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified.

S&F in repair pillar taps cast copper alloy capston headed, chromium plated, ISI Marked, screwed down, high pressure with long screwed shank and fly nut, screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap plain with grating incl jointing with solvent cement of 75mm dia.

S&F in repair tubular towel rail, chromium plated brass 20mm dia 'D' type 60CM long between flanges complete all as specified and directed.

Supply and fixing in repairs 15mm bore brass CP mixer valve for wash basin for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repairs for Toilet fittings Corner Glass shelf with bracket complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs Wall mixer (wall mounted model) with provision of connecting shower rose complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs for toilet fittings Teliphonic shower with 1.5 mtr long flexible tube & swivel wall hook complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs for Toilet fittings Health faucet with 1.2mtr long flexible tube & swivel wall hook complete all as specified and directed by Engr-in-Charge

Supply and fixing in repairs PVC cabinet of size 450 mm x 600 mm with mirror of good quality with shelves in bath fixed complete to walls complete all as directed by Engineer-in-Charge. Make : Prayag/Jaquar/Hindware

Supply and fixing in repairs for Toilet fittings Two way bib cock of 15mm bore complete all as specified and directed by Engr-in-Charge

Taking down old unserviceable 15mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 20mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

Taking down old unserviceable 25mm GI tubing, fittings and connections and removing from site or keeping aside for refixing complete all as specified and directed.

S&F 15mm bore, (concealed) water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors / trenches complete all as specified and directed.

S&F 20mm bore, water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors / trenches complete all as specified and directed.

S&F 25mm bore, water tubing, medium grade, galvanised with all fittings and fixed to walls, ceiling or laid in floors / trenches complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75mm bore PVC(SWR) bends with oval access door of any radius complete all as specified and directed.

S&F 110mm bore PVC(SWR) bends with oval access door of any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with oval access door complete all as specified and directed

M&L for complete removal of existing treatment of old plastered surface of wall and applying two coat of distemper oil emulsion / oil bound distemper over coat of 1mm thick average thick wall putty, complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying a coats of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying a coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of primer over 1mm average thick wall care putty, complete all as specified and directed.

M&L for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered/rough cast plastered wall surfaces and applying two coats of cement base paint over a coat of primer, complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for prepartion of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

S&F in repair Jet flush including plate & connection pipe complete all as specified and directed.

M&L for PCC (1:4:8) Type D-2 75mm thick using 40 graded stone aggregate as in sub base of floor all as specified.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for Chequered cement concrete tiles 25cm x 25cm x 22-25mm thick, set and jointed in neat cement slurry and pointed in white the coloured cement to match with tile laid over and including screed bed or bedding layer 15mm thick in CM (1:6) laid over and complete all as speciied and directed.

M&L for machine cut Kota stone slab flooring 18-20 mm thick over 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as spd & directed.

Dismantling Single layer of Mangalore Pattern or similar tiles in roofing complete all as specified and directed

M&L for Single layer of Mangalore Pattern or similar tiles in roofing complete all as specified and directed

All as per description of serial item No.95.00 above but except tiles complete all as specified and directed

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, beded and jointed in cement mortar 1:6

M&L for complete removal of existing treatment and applying two coats of weather proof acrylic emulsion paint including a coat of emulsion wall primer over manglore or similar tiles or wall surfaces at any height and in any position complete all as per manufacture's instructions & as directed by Engr -in-Charge. Make :- Asian / Apex / Berger (Wheather coat All Guard).

M&L for new surface and applying two coats of weather proof acrylic emulsion paint including a coat of emulsion wall primer over manglore or similar tiles or wall surfaces at any height and in any position complete all as per manufacture's instructions & as directed by Engr -in-Charge. Make :- Asian / Apex / Berger (Wheather coat All Guard).

Providing & Fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm,including dismantling of old boards/ ceiling etc complete at all heights as per direction of Engineer-in-charge.

Hacking out old broken glass (any size, quality or description) from wooden/steel frames glazed with putty or beads and S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square n exc 0.5 Sqm. in each pane complete all as specified & directed. Note :- Old wooden beads shall be reused.

S & F in repair extruded aluminium handle, fabricated type, anodised, 150mm size conforming to IS complete all as specified and directed.

Dismantling of exisiting unserviceable RCC/PVC water tank of Capacity not exceeding 500 litre each S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

Dismantling of exisiting unserviceable RCC/PVC water tank of Capacity not exceeding exc 500 but n. exc 1000 litre each S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F in repairs 20 mm dia gun metal globe or gate valve, iron screwed both ends for iron pipe or for union, ISI marked complete all as specified and directed.

S&F in repair 150mm long aluminium anodised barrel tower bolt of extruded section ISI marked all as specified and directed.

S&F in repair 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 grams) complete all as specified and directed.

M & L for precast reinforced cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in louvers & Jallies, 35mm thick including all mouldings set in CM (1:4) complete all as specified and directed.

Shree Sai Ram Enterprises

M/s AKASH CONSTRUCTION CO.

GOMA CONTRUCTION COMPANY

M/S Nexus Projects

JWALA ENTERPRISES