SPECIAL REPAIRS TO BLDG NO. P-71 (OR MD ACCN) AT NML AREA, COLABA, MUMBAI

Amount

Taking down chowkats or frame with shutters exc 1.5 sqm n exc 4.00 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engr-in-Charge

Taking down chowkats or frame with shutters n exc 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engr-in-Charge

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each including fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engr-in-Charge

S & F solid PVC door frames of size "62 mm x 32 mm solid PVC" SSR PArt-II 8.34.3.1 suitably screwed & fixing in opening as per specification & drawing on Serial Page No 160 of SSR Part II (pertaining to item No 08095) complete all as specified and as directed by Engr-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S Accucell/M/S Dura Plast Extrusion complete all as specified and directed by Engineer in charge.

Providing and fixing 30 mm thick factory made solid panel PVC door shutter as per IS 15931: 2012 consisting of frame made out of MS tube of size 15x15mm for top and bottom rails and 19x19mm for stiles, MS frame covered with 5mm thick single piece extruded PVC profile C Channel having a 5mm thick PVC sheet strip of 20mm width struck inside with solvent cement, forming the stiles and 5mm thick single piece extruded PVC profile for top rail, lock rail and bottom rail on either side and 10mm (5mmx2) thick , 20mm wide cross PVC sheet as gap insert for top rail and bottom rail, panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with PVC sheet beading and joined together with the solvent cement adhesive etc all as per manufacturers instructionsa and fixing in the frame at site as per specification & drawing on Serial Page No 161 of SSR Part II (pertaining to item No 08101) complete all as specified and as directed by Engr-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S Accucell/M/S Dura Plast Extrusion complete all as specified.

Excavation over areas n. exc 1.5 m in deep and getting out in hard/ dense soil complete all as specified and as directed by Engr-in-Charge

Dismantling timber in scantling, 40 sqcm and over in section, in any position in framed work complete all as specified and as directed by Engr-in-Charge.

S & F 2nd class hard wood (SAL) timber, clean sawn, in scantling, timber framed and fixed complete all as specified and as directed by Engr-in-Charge.

S & F in repairs 2nd class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, sectional area n exc 3sqcm, secured with nails or brads complete all as specified and as directed by Engr-in-Charge

Demolition of brick work/stone/PCC block masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, PCC coping etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engr-in-Charge.

M & L for brick work with sub class "B" bricks, straight or curved on plan, exc 6 mtr mean radius with old size bricks and built in cement mortar (1:6) complete all as specified and as directed by Engr-in-Charge

M & L for brick work with sub class "B" bricks, straight or curved on plan, exc 6 mtr mean radius, except bricks and built in cement mortar (1:6) complete all as specified and as directed by Engr-in-Charge. Note:- Serviceable bricks obtained vide item No. 10 above shall be used.

Demolition of reinforced cement concrete of any description (reinforcement cut as required to facilitate demolition) and in any position(beam, landing, chajja, roof slab etc), above or below ground floors, not otherwise specifically provided for and removing the same outside MD land complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of internal dia 150 mm, set in cement mortar and removing the same outside MD land complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position, not otherwise specifically provided for including PCC flooring over sewage line and paving not exc 15cm thick above or below ground level and removal of rubbish outside MD Land complete all as specified and as directed by Engr-in-Charge.

Dismantling of FRP/plain or corrugated steel sheeting, any gauge, thickness including any pattern in wall coverings i.e chajjas including brackets and removing the same outside MD land complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness laid in floors, aprons etc, laid, bedded and pointed in any mortar and and removing the rubbish outside MD land complete all as specified and as directed.

Taking down cement plaster on brick or stone/concrete surfaces, etc. on internal/external surface of wall/ceiling including raking out joints, hacking for key, scrubbing down with water to receive plaster and removing debris out side MD land complete all as specified and as directed by Engr-in-Charge.

M & L for dubbing out averaging 15mm thick in CM (1:6) on irregular face of wall (when specifically ordered in writing by AGE) and finishing the surface even and fair without using extra cement complete all as specified and as directed by Engr-in-Charge

Taking down eaves gutters and rainwater pipes (any size or pattern), soil waste pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by Engr-in-Charge

Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, in any weight, n exc 4 kg/ Sqm complete all as specified and as directed by Engr-in-Charge

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation etc or for shaft, walls, manholes, pier holes etc, not exceeding 10 sqm on plan and getting out in soft/loose soil complete all as specified & directed by Engineer-in-Charge

S & F mild steel work as in hold fast & similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing surfaces of wood and wood based materials, steel and iron work, treating ends of posts, hold fasts, backs of chowkats, etc., area tarred not exceeding 0.5 sqm each and treated with tar or coal tar black paint complete all as specified and as directed by Engr-in-Charge.

S & F plain solid straight chowkats, second class hardwood (SAL), wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

S & F for factory made second class hard wood (Hollock) 35 mm thick, timber species of super group and durability class I as per IS 12896: 1990 and first grade as per IS 1003 (Part-1): 2003, factory made, panelled shutters (two panels) with lock rail and panel of 12 mm thick veneered particle board, Grade -I, Type -I (solid core, general purpose), designation (SO GP-I) conforming to IS 3097, supplied and fixed to chowkats, the size of style and rail as per IS 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

S & F for factory made second class hard wood (Hollock) 30 mm thick, timber species of super group and durability class I as per IS 12896: 1990 and first grade as per IS 1003 (Part-1): 2003, factory made, glazed and skeleton shutters, subdivided into small panes using muntins (sash bars), open rebated and prepared to receive glass, wire gauze, etc., edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part-I section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-Charge.

M & L for machine cut cuddapa stone slabs 20-25 mm thick as in window cills/jamb over and including 15 mm thick screed bed in cement mortar (1:6) or rendering coat of 10mm thick in CM 1:4 and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing, polishing & rounding of edges complete all as specified and as directed by the Engineer-in-Charge.

S & F powder coated aluminium sections for doors, windows, ventilators, door partition including fabrication of frame shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, and rubber beadings for fixing glass panes in frame complete all as specified and as directed by the Engineer-in-Charge. Note : (i) Glass panes & handle will be measured & paid separately. (ii) The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India

S & F prelaminated particle board (decorative lamination on one side and other side balancing lamination), 20 mm thick, grade I or II & type II (Designation PLB-12 or PLB-22), made out of medium density particle board (flat pressed-three layer or multilayer and graded (grade I or grade II), bonded with BWP adhesive), fixed with screws to timber/ steel frame work for horizontal applications as in table tops, counter, furniture tops, etc. complete all as specified and as directed by the Engineer-in-Charge. Make- 1.Novapan 2 Eco Board Industries, Pune 3 Kitply 4 Anchorlam 5 Century Plywood

S & F Aluminium grill of 7.5mm X 5.2mm bars of opening as per design no DG No 103 M/s Decogrill/RG - 103 of M/s Royal Grill fixed with and including aluminium channel 'F' 20mmX 15mm, fixed in postion with screws complete all as specified and directed by Engineer-in-Charge.

S & F in repair continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F stainless steel butt hinges, heavy duty of 100mm size complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 150 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

S & F Stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture, 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engr-in-charge.

S & F in repairs Stainless steel alloy wire mesh,0.45mm nominal dia of wire and average width of aperture, 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engr-in-charge.

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed by Engr-in-charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F cast aluminium alloy handle, cast type, 150 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 omplete all as specified and as directed by Engr-in-charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminium hasp and staple, type 1, safety type, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 including fixing with screws of size 115 mm complete all as specified and as directed by Engr-in-Charge Make : Classic/ Shalimar/ CLIF/ARGET

S & F aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy , 300mm long, ISI marked, anodized to a bright natural mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F in repairs floor door stoppers made out of aluminium alloy pressure die casting body and tongue with hard drawn steel wire spring, overall length of cover plate 140 mm, 4.5 mm thickness of cover plate, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996, suitable for 30 & 35 mm thickness of door shutter, fixed in floor complete all as specified and as directed by Engr-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

S & F 4.0mm thick sheet glass, plain, ordinary quality,in square or rectangles, not exc. 0.5 Sqm in each pane, glazing with rubber beading complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

S & F in reapairs Harrison curtain rails, 20mm dia, anodised aluminium alloy, chromium plated complete all as specified and as directed by Engr-in-Charge.

S & F in repairs Fancy type, decorative bracket suitable for curtain rod 20mm dia complete all as specified and as directed by Engr-in-Charge.

S & F in repair louvered section 9 blades including lever handle, lock water tighting using silicon compound etc & fixing with aluminium frame complete all as specified and as directed by Engr-in-Charge.

S & F figured glass, 4mm thick, pin headed, glazing with oil putty, in square n exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

S & F in repairs 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed by Engr-in-Charge. Make:Commander/ Hindware/ Paryware/ CERA.

M & L for PVC connections with brass socket on both sides, 15 mm size of length 600 mm ccomplete all as specified and as directed by Engr-in-Charge

M & L for cement mortar (general purpose, factory made, for indoor use having bulk density (of dry mix) 1600 kg per cubic metre, wet density (after mixing) 1600 kg per cubic metre, dry density (after setting) 1800 kg per cubic metre, pot life 60 minutes, compressive strength 3.5 Mpa to 7.5 Mpa, capillary water absorption ≤ 0.40 kg/ sqm min 0.5, adhesion 0.5 N/sqmm fracture pattern: B, Water-vapour permeability coefficient μ 15/35 as per BS EN 998-01 : 2010, made using well graded manufactured sand filler, Portland cement & polymer binder, and chemical additives) for internal rendering 10 mm thick on brick wall or concrete surfaces including making groove of appropriate size complete all as specified and as directed by Engr-in-Charge. Name of Manufacturer: M/s Premier Floor to Roof Materials pvt. ltd/ M/s Walplast Products pvt. ltd/ M/s Ultratech Cement Ltd/M/s Sound buildcare pvt. Ltd/ or other approved equivalent make.

M & L for cement mortar (general purpose, factory made, for indoor use having bulk density (of dry mix) 1600 kg per cubic metre, wet density (after mixing) 1600 kg per cubic metre, dry density (after setting) 1800 kg per cubic metre, pot life 60 minutes, compressive strength 1.5 Mpa to 5 Mpa, capillary water absorption ≤ 0.40 kg/ sqm min 0.5, adhesion 0.5 N/sqmm fracture pattern: B, Water-vapour permeability coefficient μ 15/35 as per BS EN 998-01 : 2010, made using well graded manufactured sand filler, Portland cement & polymer binder, and chemical additives) for internal rendering 5 mm thick on ceiling surfaces including making groove of appropriate size complete all as specified and as directed by Engr-in-Charge. Name of Manufacturer: M/s Premier Floor to Roof Materials pvt. ltd/ M/s Walplast Products pvt. ltd/ M/s Ultratech Cement Ltd/M/s Sound buildcare pvt. Ltd/ or other approved equivalent make.

M & L for Providing cement concrete type B1 1:2:4 (using graded stone aggregates 12.5mm) as in copings and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work for fair finished surfaces complete all as specified and as directed by Engineer-in-Charge.

M & L for 75mm thick cement concrete (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including joints of plinth protection filled with bitumen mastic (1:3) complete all as specified and as directed by Engr-in-Charge.

M & L for machine cut Kota (greenish colour, pre polished) stone slab flooring, 20-25 mm thick, in one piece as in cill/staircase treads etc, over cement screed bed 20 mm in CM (1:3) base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer in Charge.

M & L for machine cut Kota (greenish colour, pre polished) stone slab flooring, 18-20 mm thick, in one piece as in vertical surfaces, skirting etc, set and jointed in neat cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and pointed in colour cement to match including backing coat 10 mm in CM (1:3) complete all as specified and as directed by Engr-in-Charge.

S & F in repair vitreous china, white, semi pedestal pattern water closet (Anglo Indian type), fixing bolt, flush pipe, including seat and cover, flush pipe, rubber cone etc (excluding flushing Cistern,), including connecting to drain and flushing pipe, anti syphonage pipe complete all as specified and as directed by Engr-in-Charge. Make:Hindware (Ist Quality)/ Parryware (Super Fine)/ Cera (Ist Quality) /Jaquar

S & F in repairs vitreous china squatting pan, ‘Orissa’ pattern of size 580 x 440 mm white, with integral foot rest (excluding flushing Cistern, flush pipe etc) including 'P' or S trap, connector piece of CI pipe upto 'T'/ 'Y' joint and connection to trap and to flushing pipe, anti-syphonage pipe etc and provision of lime concrete bedding complete all as specified and as directed by Engr-in-Charge. Make:Hindware (Ist Quality)/ Parryware (Super Fine)/ Cera (Ist Quality) / Jaquar

M & L for PVC (SWR ) gully trap 125/110 mm with grating or without grating and jointing with solvent cement and fixed in position complete all as specified and directed including cement concrete type B1. 1:2:4, using 20 mm nominal size graded crushed stone aggregate complete all as specified and as directed. Make- Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

Supply only liquid water proofing compound. Make - Plastocrete of Sika/Pidiproof LW of Pidilite.

S & F PVC-U, type A as per IS 13592: 2013, single socketed rain water pipes in any length with rubber ring joints, 110 mm dia, fixed to walls complete all as specified and directed by Engineer- in- charge . Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F PVC-U, type B as per IS 13592: 2013, single socketed rain water pipes in any length with rubber ring joints, 110 mm dia, fixed to walls complete all as specified and directed by Engineer- in- charge . Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F UPVC branch piece, Wye (45 degree) single, 110 mm dia without inspection door conforming to IS 14735: 1999 at any height including cost of scaffoldings complete all as specified and directed by Engineer- in- charge . Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F UPVC Tee(87.5 degree) single, 110mm dia without inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge.: 1999 at any height including cost of scaffoldings complete all as specified and directed by Engineer- in- charge . Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F UPVC bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F UPVC vent cowl, 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F Pre-painted galvalume aluminium zinc coating GI based mangalore pattern profile roofing sheets 0.50 mm thick of any colour/length having tensile strength of 550 MPA, AZ 150 as in roof coverings having effective & overall width 1015 mm &1072 mm respectively, tiles steps-200mm, profile height 28.5mm and centre to centre distance between ribs 203 mm, fixed with self tapping screws at 500mm centre to centre, as directed by manufacturer on wooden/steel members including scafoldings of any hieght complete all as specified and directed. Make- (i) TATA (ii) JSW (iii) ESSAR (iv) HINDALCO (v) INDALCO (vi) ASSOCIATED PROFILES AND ALUMINIUM LT

S & F 110mm PVC (SWR) sanitary short connections pipe of length upto 300 mm complete all as specified and directed by Engineer- in- charge Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius, in half brick thick walls with old size bricks, built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge

M & L for concrete bed to RCC pipes of internal diameter 150 mm, class NP3, laid in trenches of depth upto 1.2 mt, in cement concrete M10(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate including packing under and haunching against the sides of pipes after testing of pipe complete all as specified and as directed by Engineer-in-Charge

M & L for RCC pipe, class NP-3, 150mm bore, laid and jointed with cement slurry and spun yarn complete with spigot and socket collars complete all as specified and directed by Engr-in-Charge. Make- 1.Thuluvananikal Pipes 2 Everest 3 Himalaya 4 Indian Hume Pipes

Removing excavated soil to a distance exceeding 5 Km but not exceeding 15 Km and depositing where directed complete all as specified and as directed by Engr-in-Charge.

M & L for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

M & L for preparing old wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engr-in-Charge.

M & L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed by Engr-in-Charge.

M & L for machine cut cuddapa stone slabs 35-40 mm thick as in cooking platform over and including 15 mm thick screed bed in cement mortar (1:6) or rendering coat of 10mm thick in CM 1:4 and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing, polishing & rounding of edge on one side of the slab, cutting hole complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engr-in-Charge.

M & L for non skid Digital coloured ceramic tiles (group B II), 400mm x 400mm x 7mm thick in floors etc., set and jointed in neat cement slurry and pointed in epoxy mortar to match, over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for non skid Digital coloured ceramic tiles (group B II), 600mm x 600mm x 8mm thick in floors etc., set and jointed in neat cement slurry and pointed in epoxy mortar to match, over and including screed bed of 15mm thick in CM (1:6) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for glazed Digital coloured ceramic tiles (Group B III) of size 300 x 450 x 8 mm thick or 450 x 350 x 7mm thick (or nearest size) on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in epoxy mortar to match including backing coat 10 mm in CM (1:4) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

M & L for glazed Digital coloured ceramic tiles (Group B III) of size 350 x 250 x 8 mm thick or 450 x 350 x 7mm thick (or nearest size) on vertical surface such as skirting, dado, riser/steps etc, set and jointed in neat cement slurry and pointed in epoxy mortar to match including backing coat 10 mm in CM (1:4) complete all as specified and as directed by Engr-in-Charge. Make:M/s H R Johnson/M/s Orient Bell Tiles/M/s Kajaria/M/s Somany Tiles Ltd/M/s Nitco tiles/M/s Swastik Tiles

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets conforming to Fe 290 omplete all as specified and as directed by Engr-in-Charge.

S & F rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam , tee, angle, channels or flat sections),distance pieces, cleats etc including notching, drilling, fitting, rivetting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 290 Gde E- 165 complete all as specified and as directed by Engineer-in-Charge.

M & L for Mild Steel framed work such as grills, gratings, etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, framed work of garbage bin, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 Gde 165 etc. complete all as specified and as directed by Engr-in-Charge.

Providing and erecting steel props (about 14' height wooden at centre and supporting a continuous 2" x 3" wooden runner, resting on wedge and block minimum capacity 1 ton ) to support the structure provisionally during repair and jacketing etc. and maintaining them in position till required and taking away all materials complete all as specified and as directed by Engr-in-Charge.

Providing and erecting at site self supported two legged B class tubular steel scaffolding to reach any place of work on external façade of building, including approaches, extension, working platform, ladders, fitting tackle for men and material etc. all complete, dismantling and taking away all materials and debris after completion of proposed work etc.complete all as specified and as directed by Engr-in-Charge.

Erecting only at site self supported two legged B class tubular steel scaffolding to reach any place of work on external façade of building, including approaches, extension, working platform, ladders, fitting tackle for men and material etc. all complete, dismantling and taking away all materials and debris after completion of proposed work etc.complete all as specified and as directed by Engr-in-Charge.

Providing and erecting horizontal industrial safety net as per IS 11057: 1985, made out of polypropylene rope as per IS 5175: 1992, mesh size 75 mm X 75 mm, border cord 12 mm, tie cord 12 mm, mesh cord 4 mm including overlay with HDPE net to catch personnel and debris and keeping the same during the period of work and including dismantling and taking away after completion of the work complete all as specified and as directed by Engr-in-Charge.

Providing and erecting vertical scaffolding net (debris net), made out of high density polyethylene for dust and debris control and keeping the same during the period of work and including dismantling and taking away after completion of the work complete all as specified and as directed by Engr-in-Charge.

Providing, erecting and subsequently dismantling temporary GI sheet /plywood portions with 2.00 metre high fixed on bamboos/wooden post etc. within the premises so as to isolate the living area from working area and taking away all materials complete all as specified and as directed by Engr-in-Charge.

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slabs/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 25 mm average depth including saw-cutting of all edges making square shoulders of the cavities complete all as specified and as directed by Engr-in-Charge. (All loose unsound and cracked concrete shall be removed out side MD land) (Note: thickness will be measured excluding plaster)

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slabs/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 40 mm average depth including saw-cutting of all edges making square shoulders of the cavities complete all as specified and as directed by Engr-in-Charge. (All loose unsound and cracked concrete shall be removed out side MD land) (Note: thickness will be measured excluding plaster)

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slabs/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 60 mm average depth including saw-cutting of all edges making square shoulders of the cavities complete all as specified and as directed by Engr-in-Charge. (All loose unsound and cracked concrete shall be removed out side MD land) (Note: thickness will be measured excluding plaster)

Cleaning loose concrete, if any, all around reinforcement including from behind the reinforcing bars to give an average 10 mm thick (but not less than 10 mm clear air gap) and cleaning reinforcement of total rust using alkaline rust remover with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washed with water and allowing it to dry complete all as specified and as directed by Engr-in-Charge. (Note : - Length of reinforcement bars cleaned of rust all around will be measured for payment.) (Note: thickness will be measured excluding plaster)

Applying two coats of epoxy based passivating, protecting & bonding coat of zinc rich system (Nitozinc (R) primer of Fosroc and equivalent of SIKA/Dr Fixit Pidilite/ Krishna Conchem) as approved by the Engineer-in-Charge for old and new reinforcement any dia complete all as specified and as directed by Engr-in-Charge. (Note: Epoxy based passivating, protecting & bonding coat of zinc rich system will be paid for separately).

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height Ccomplete all as specified and as directed by Engr-in-Charge.

M & L for mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips ccomplete all as specified and as directed by Engr-in-Charge.

Mixing and applying SBR latex modified cementitious bond coat using cement 2.2 kg per square metre on prepared concrete surfaces of parent material complete all as specified and as directed by Engr-in-Charge. (Note: SBR latex will be paid for separately)

Mixing and applying SBR latex modified cement mortar 25 mm thick in cement sand mortar in proportions of 1:3 (1 cement and 2 graded quartz aggregate) with polymer admixed in proportions as approved, including trowelling with wooden tools on prepared concrete surfaces of parent material complete all as specified and as directed by Engr-in-Charge. Note: Acrylic polymer will be paid for separately)

Supply only approved SBR latex from FOSROC/BASF/DR FIXIT/ SIKA for bonding coat/Polymer modified cement mortarc complete all as specified and as directed by Engr-in-Charge. (Note: Rate will be in terms of solid contents of polymer)

Providing and placing in position micro-concrete, grade M40, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, thickness of section upto 75 mm complete all as specified and as directed by Engr-in-Charge. (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)

Providing and placing in position micro-concrete, grade M40, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, thickness of section exceeding 75 mm complete all as specified and as directed by Engr-in-Charge. (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)

Providing and fixing special water tight centering and shuttering including bolting, strutting, propping etc. so as to withstand a pressure of 0.1 Mpa including removal of form from all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies etc. complete all as specified and as directed by Engr-in-Charge.

M & L for RCC M30 (Design Mix) using 20 mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M & L for sand faced cement plaster 20mm thick (12mm+8mm) in two coats on external wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Soundplast PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:4 using fully treated dry, well graded natural sand confirming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 12 mm thick and finishing coat of 8mm thick final rendering, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required, and finishing the surface even and fair without using extra cement including cleaning the surfaces, curing etc. complete all as specified and as directed by Engineer-in-Charge

M & L for preparing of new plastered surfaces of wall/ceiling by scrapping/rubbing and applying two coats of Acrylic weather proof exterior paint over a coat of acrylic primer complete including scaffolding complete all as specified and as directed by Engineer-in-Charge and as per manufacturers instructions. Make- (a) Asian Paint - Apex Ultima Protek. (b) Berger Paint - Weather coat smooth. (c) Nitco Paint - Outshine premium 100% acrylic exterior (d) ICI Dulux - Weather shield exterior.

M & L for cutting out cracks to 'V' section in existing roofs or terracing, fixing of chajja etc, cleaning out, wetting, grouting with cement slurry mixed with water proofing compound complete all as specified and as directed by Engineer-in-Charge

M & L for cement concrete PCC 1:2:4, type B-1, using 20 mm nominal size graded crushed stone aggregate, 40 mm thickness (average) as levelling course of roof padding including brushing neat cement slurry on old concrete surface @ 3.0 kg of cement per sq meter and finishing the surface even and fair complete all as specified and as directed by Engineer-in-Charge

M & L for screed bed 15mm thick with polymer mortar made out of Shali SBR latex, cement and sand in the ratio of 1:1.5:12.5 mixed with water to fill voids and undulation area of roof and finshed even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge

M & L for preparation of surface by complete removal of previous water proofing treatment and Prime the surface with ShaliPrime WB diluted with water in the ratio 1 : 0.5 and apply @ 5-8 L / m2 and apply two coats of Shalicryl 215 UV resistant elastomeric coating over Shaliurethene BTD bituminous modified elastomeric liquid membrane over ployster reinforcement over priming coat. The rate of application being the same. The Colour of First and Last Coat will remain same. Drying time between coats will be 6 to 8 hrs. Allow the system to air cure for 7 days mimnimum. A total thickness of 1 to 1.2 mm must be achieved when Shalicryl LM is Dry and removing rubbish /debris outside MD land complete all as specified and as directed by Engineer-in-Charge Note : Work Shall be Executed through manufacturer applicator. Equivalent product of technique of Fosroc/Dr Fixit can also be used.

S & F wash basins, vitreous china, white, flat back, size 550 mm X 400 mm including one no waste fitting brass chromium plated 32mm dia with long screwed shank and fly nuts, flange end bedded in red lead cement and other end fixed with one no. PVC waste pipe 25mm dia and 75cm long with 32mm dia connector, one no. 15mm bore pillar tap, cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shank and fly nuts, screwed for iron pipe and PVC connection 15mm dia and 600mm long with two nos check nut and washer complete including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws) including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed by Engineer-in-Charge Make:Neycer Kermag (Standard)/Hindustan Sanitary Ware Industries (Ist Quality)/Parryware (Super Fine)/Cera(Ist Quality)/Jaquar

S & F 40 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/cm2 with all pipe fittings, fixed complete to walls, ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

S & F 32 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/cm2 with all pipe fittings, fixed complete to walls, ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge. Make : Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

M & L for preparing new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge. Make-(a) LUXOL (Berger paint) (b) BROLAC (Johnson & Nicholson) (c) SUPERLAC (Shalimar Paints) (d) NEROLAC (Goodlass Nerolac) (e) APCOLITE (Asian Paints)

S & F sinks with drainage board made of stainless steel 1 mm thick sheet (AISI 304 quality), glossy finish, kitchen or laboratory with plugs, washers and 40 mm nominal size, copper alloy, nickel chromium plated finish waste fittings with including silicone sealant; waste pipeof 38/40mm bore x 1150mm long cutting groove to wall ,bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipes overall size 915 mm X 460 mm bowl size 410 mm X 330 mm X 200 mm or to the nearest size complete all as specified and as directed by Engr-in-Charge. Make- Blue Star/ Prayag/ Jindal/Nirali

S & F in repairs towel rail 600 mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastics cleats, minimum weight 170 gms complete all as specified and as directed. Make- Jaypee/ GMP/ Neta/ Zolota/ Prayag polimer/ Symet

S & F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium brackect guard and railing 60cm long complete all as specified and as directed by Engr-in-Charge

M & L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a thin layer of wall care putty complete all as specified and directed by Engineer in Charge. Make: SHALIMAR / BERGER / NEROLAC / ICI LTD/ASIAN (Tractor UNO)

M & L for preparation of plastered surfaces of wall including complete removal of existing treatment and applying two coats of oil bound distemper over a coat of alkali resistant primer over a thin layer of wall care putty complete all as specified and directed by Engineer in Charge. Make: SHALIMAR / BERGER / NEROLAC / ICI LTD/ASIAN (Tractor UNO)

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any soil complete all as specified & directed by Engineer-in-Charge.

S & F Cast iron soil, waste and vent Spun pipes (75mm) with or without ears, with cement joints, laid in trenches or in floors complete all as specified & directed by Engineer-in-Charge. Make-(a) NECO, Nagpur (b) SKF (Singhal Iron Foundry, Mathura)

S & F in repairs PVC (SWR) Nahani trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 75 mm including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and as directed by Engr-in-Charge Make- Prince/Finolex/Supreme/HIL Limited (Birla Aircon)

M & L for rendering 15mm thick plaster in CM (1:4) on fair faces of the brick or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm each including fittings & refixing in the same opening including cutting, replacing hinges and all necessary work complete all as specified and as directed by Engr-in-Charge

M & L for machine polishing to existing kota stone flooring,firstly with machine fitted with fine grade blocks (No. 120), followed by the final grinding with machine fitted with the finest grade grit blocks (No. 320), the day after the first grinding described above or before handing over the floor, after the final polish, oxalic acid shall be dusted over the surface at the rates of thirty three (33) gms. per square metre sprinkled with water and rubbed hard with pad of wooden rags & the following day the floor shall be wiped with a moist rag and dried with a soft cloth and finished clean complete all as specified and as directed by Engr-in-Charge.

M & L for stainlees steel tubing of grade 304 (Square/round/rectangular) of suitable guage as in guard bars, railing, frame work including all fixing arrangemnet including taking down of old Mild steel guard railing complete all as specified and as directed by Engr-in-Charge.

M & L for stainlees steel grade 304 as in railing pillar with base plate and pillar ball, mirror polished complete all as specified and as directed by Engr-in-Charge.

S & F in repairs steel water tubing of size 15mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge. Make- (a) Tata (b) Swastik (c) Jindal (d) Surya (e) Prakash (f) Indian Tube Company (g) Zenith (h) BST (j) GST (Gujrat Steel Tube)

S & F in repairs steel water tubing of size 20mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge. Make- (a) Tata (b) Swastik (c) Jindal (d) Surya (e) Prakash (f) Indian Tube Company (g) Zenith (h) BST (j) GST (Gujrat Steel Tube)

S & F in repairs steel water tubing of size 40mm bore, medium grade, galvanised iron with all Fittings such as Tees, elbows, sockets, bends, unions, shortpieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches and making good disturbed surfaces to match the existing surfaces complete all as specified and as directed by Engr-in-Charge. Make- (a) Tata (b) Swastik (c) Jindal (d) Surya (e) Prakash (f) Indian Tube Company (g) Zenith (h) BST (j) GST (Gujrat Steel Tube)

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 4000 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including taking down existing unserviceable PVC water tank and removing clear off site after credit for the same is recovered by the dept complete all as specified and as directed by Engr-in-Charge. Make- (i) M/s Sintex (ii) M/s Infra (iii) M/s Ashish Plast (iv) M/s Yash Engineering Works, Pune 09422007879 (v) M/s Plasto (vi) Polycon

S & F in repairs 40mm bore Gun Metal Gate Valve with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr -in-Charge. Make-(i) Leader (ii) Zoloto (iii) Sant

S & F in repairs 15mm bore stop valves, cast copper alloy, chromium plated , screwed down, high pressure, with crutch of butterfly handle, screwed down both ends for iron pipe or for unions , conforming to IS complete all as specified and as directed by Engr-in-Charge. Make:Jaguar/Sona/Leader/Zoloto/Sieco/Prima/Prayag

S & F in repairs, bib taps, chromium plated, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed. Make : Jaypee/GMP/Neta/Zoloto/Prayag polimer/Prima

S & F Ball Valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed of 40 mm bore complete all as specified and as directed by Engr-in-Charge (Minimum weight - 690 gms) Make- (i)Jaypee (ii) GMP (iii) Neta (iv) Zolota (v) Prayag polimer (vi) Symet

S & F in repairs Swivel shower of PTMT,any colour, for fixing with 15mm pipe, minimum weight 40gms complete all as specified and as directed by Engr-in-Charge. Make- (i)Jaypee (ii) GMP (iii) Neta (iv) Zolota (v) Prayag polimer (vi) Symet

S & F in repairs shower arm 15 mm size, 195mm long with bend of 45 degree with flange of PTMT any colour.(Minimum weight 40gms) complete all as specified and as directed by Engr-in-Charge Make- (i)Jaypee (ii) GMP (iii) Neta (iv) Zolota (v) Prayag polimer (vi) Symet

S & F in repair stainless steel Health faucet with 1.5mt long SS pipe with holder,15mm dia with hook, fixed to wall with screws and connection with pipe complete all as specified and directed by Engr-in-Charge. Make:(i) Jaguar (ii) Sona (ii) Leader (iv) Zoloto (v) Sieco (vi) Prima (vii) Prayag Polimer

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, regulators, switch socket outlet, bulk head fittings, tube light fittings etc and removing unserviceable materials from site of work after credit for the same is recovered by the dept and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and directed by Engineer-in- Charge

M & L for point wiring for one light or one fan or one exhaust fan controlled by one switch complete with and including single core PVC insulated, unsheathed flexible conductor FRLSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including heavy mechanical stresses class and -5 temperature class PVC casing/capping of suitable size as required at site including all accessories/ fittings/ junction boxes/ inspection cover etc., ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FRLSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. Make for cable :Havells/Finolex/ Nicco/Plaza/ Anchor/Polycab/RPG/GLOSTER/RR Kabel/KEI Make for Casing & Capping : Precision/ Modi/Presto Plast/ Supreme/ Polycab/ Plaza/Pressfit

All as per serial no.140 here-in but for bell point controlled by one switch

All as per serial no.140 here-in but for one light point controlled by two way switches (two way switch point wiring)

All as per serial no.140 here-in but for one ceiling fan controlled by one switch & regulator

All as per serial no.140 here-in but for One 3 pin socket point 5 Amps on independent board

All as per serial no.140 here-in but for One 3 pin socket point 5 Amps on same board

All as per serial item no 140 here-in-before but for one socket point on independent board, 15 Amp with 2.5 sq mm PVC unseathed FRLSH wire along with 2.5 sq mm FRLSH green colour wire as earth continuity conductor connected to common earth dolly complete all as specified & as directed by engr-in-charge.

S & F Switch, piano type, single pole, one way, 5 amps, 240 volt flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F Switch, piano type, single pole, one way, 15 amps, 240 volt flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F switch socket outlet, 2/3 Pin, 5 Amps, flush type complete all as specified and as directed by Engineer-in-Charge. Make :(i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F switch socket outlet, 6/16 Amps, 2/3 pin, flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F step type electronic fan regulator, capacitor type, 100 watt, 450 volts, 50 Hz, single phase, flush type on the existing phenolic laminated sheet complete all as specified and as directed. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F Bell push AC, 240 volt, 6 Amp, flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F ceiling roses, surface type backalite 65 x 50 mm two to three terminals complete all as specified and as directed. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F Switch, piano type, single pole, two way, 5 amps, 240 volt flush type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F lamp holder , insulated body with back plate for angular batten fittings with one PVC block of size 75mmX75mm for mounting the fitting including one LED lamp 12 watt complete as specified and directed. Make of lamp holder : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd Make of lamp : (i)Philips (ii) Havells (iii) Wipro

S & F 20 watt LED, 4 feet long, fixed on & including PVC square for mounting the fittings and electrically connecting with three single core 23/0.0076 PVC insulated, multi strandard, copper flexible cable from ceiling rose to light fitting (connector block of lamp fitting) and one for earthing complete all as specified and directed Make:Havells cat pt no LHEXBXPNIN1W020 or equivalent model in Wipro model no - Wipro Garnet 20 W LED Batten 6500K / Philips model No - BN150W LED 20S-6500 PSE ODGR / OSRAM.

S & F surface mounted 10 watts LED tube light fitting, mirror light fitting with lamp, fixed on & including PVC square for mounting the fittings and electrically connecting with three single core 23/0.0076 PVC insulated, multi strandard, copper flexible cable from ceiling rose to light fitting (connector block of lamp fitting) and one for earthing complete all as specified and directed Make:- Wipro, Model No : Wipro Garnet 10W LED Batten 6500K or in equivalent model in Havells / Philips model no BN021LED10S-2ft.

S & F Electric call bell AC 230 V single pole ding dong type complete all as specified and as directed by Engineer-in-Charge. Make : (i) Anchor (ii) Crabtree (iii) Leader (iv) Legrand (v) Havells (vi) C & S Electric Ltd

S & F decorative wall mounting fitting , working on 240 volts ,50 hz AC supply fittings comprising with stainless steel finish fixture including with opal glass diffuser and with led bulb of capacity 7 WATT complete all as per specified and directed. Make : Philips / Havells / Wipro

S & F in repairs LED building security light, 45 Watt, 2500 lumens luminaire fixture in IP 65/66 protection level with aluminum pressure die cast reflector with heat shrink LM 6, dedicated optics with precise light distribution SDMC not less than 5 uniform lighting quality and UV stabilized, output of LED lamp efficiency 100 luman per watt after all losses, driver with 4KV surge high and low voltage protection, power factor not less than 0.97, life of LED 50,000 burning hours and including suitable bracket made out of GI pipe 25mm/40 mm bore light grade (as per fitting bas dia) of approximate length 2mtr long bent to shape and fixed to wall with two Nos. MS clamps made out of 32 x 6mm thick flat with nuts, bolts and washers etc., including connecting up with 2 core 1.5 sqmm PVC insulated PVC sheathed weather proof multi stranded aluminium conductor cable 1100 volts grade upto junction box including painting of clamps with two coats of aluminium paint over a coat of approved primer all as specified and as directed. Make:-Havells, cat part No. ENDURACITYLINERNEX GENSL45W LED 757SASYBOPC or equivalent make of Philips Car Part No BRP409LED 065CWHEMRFG SI PSU GR / Wipro Cat Part No LR 02-501-XXX-57-XX

S & F in repairs MCB SP, 6 amps to 32 amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs MCB SPN, 40 amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs sheet metal enclosures, double door, for DBs when MCBs to be used, 240 volts, 8 way with 200 Amps rated bus bar,single pole and neutral, fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/ thimbles duly crimped for connection complete all as specified and directed. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

M & L in repairs for earthing complete with galvanised steel plate earth electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to earthing lead strip of 32 mm X6 mm galvanised mild steel strip by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre, connected to main switch board or main control board as directed and all as shown in electrical plate No.3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 cm X 40 cm X 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 40 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/ strata and testing complete all as specified and as directed by the Engineer-in-charge.

Taking down old unserviceable submain wiring complete including all fixtures such as switches, bulk head fittings, building security light fittings, plug socket boxes etc, removing unserviceable materials from site of work and making good disturbed surface to match the existing surface complete all as specified and as directed by the Engineer-in-charge.

M & L for Submain wiring complete with and including 2 runs of 10 sqmm single core FRLSH PVC insulated and unsheathed multistranded copper conductor cable single core 1100 Volts grade and 10 sqmm FRLSH PVC multistranded copper conductor cable as earth continuity conductor and connected to common earth dolly for housing the wires for one SPN DB, drawn through and including PVC conduit, heavy duty of adequate size ( not less than 25mm dia) including accessories, fixed on walls including taking down existing submain wiring complete all as specified and as directed by Engineer-in-Charge. Note: Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB Make for cable :(i) Havells (ii) Finolex (iii) Nicco (iv) Plaza (v) Anchor (vi) Polycab (vii) RPG (viii) GLOSTER (ix) RR Kabel(x) KEI Make for PVC Conduit : (i) Anchor (ii) Modi (iii) Presfit (iv) Precision (v) Astral Note : Two runs of 10 sqmm PVC insulated cable and one run of 10 sqmm cable and one run of PVC conduit shall be measured as one unit length.

S & F in repairs DB vertical type 8 way TPN in repair, double door load line powder coated complete alongwith 200 Amp rated Bus bar with 200 Amps MCCB, adjustable type with breaking capacity 16 KA, fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed. Note: Thimble/lugs of rating of MCCB should be used with wire for fixing in the MCB complete all as directed. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric Make of MCCB: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs DB vertical type 8 way TPN in repair, doubble door load line powder coated complete alongwith 200 Amp rated Bus bar, fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection complete all as specified and directed. Note: Thimble/lugs of rating of MCCB should be used with wire for fixing in the MCB complete all as directed. Make of DB: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

S & F in repairs MCB TPN, 35 to 60 amps, 'C' series, breaking capacity 10 KA, 'C' curve, 240 volts, 50Hz including necessary incoming and outgoing electric connection with suitable size of copper lugs etc., complete all as specified and directed. Make: (i) Larsen & Tubro (ii) Siemens (iii) Schneider (iv) ABB (v) Havells (vi) Legrand (vii) Indo ASIAN (viii) C & S Electric

Taking down ceiling fan 1200/1400 mm sweep / exhaust fans including disconnection of electric connection, dismantling blades and removing fan and blades and deposit to MES store complete all as specified and as directed.

Fixing/ hanging only ceiling fan and connecting up including provision of three single core 23/0.0076 PVC insulated, multi strandard, copper flexible cable from ceiling rose of connectors to fan complete all as specified and as directed.

S & F sub main wiring complete with and including four Nos single core PVC insulated, unsheathed flexible conductor FR-LSH cables 16 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through and including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 25 mm nominal size including all accessories and fixed on walls and 16 sqmm one No single core copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable for earthing and connected to common earth dolly including taking down existing sub main wiring complete all as specified and directed by Engineer-in-charge. Note - Four runs of 16 sqmm cable, one run of 16 sqmm cable and one run of conduit will be measured and paid as one unit length. Make for cable :(i) Havells (ii) Finolex (iii) Nicco (iv) Plaza (v) Anchor (vi) Polycab (vii) RPG (viii) GLOSTER (ix) RR Kabel(x) KEI Make for PVC Conduit : (i) Anchor (ii) Modi (iii) Presfit (iv) Precision (v) Astral

SHREE JAGDISH FURNITURE CO.

Garima Construction Co

ORIENT ELECTRIC CO