Tender for Construction of Additional Drug warehouse at Tirunelveli

Amount

Dismandling, clearing away and carefully stacking materials useful for re-use for any thickness of wall

Brick masonry in cement morter walls unter 3 m height

dismantling R.C.C

Pressed tiles and weathering course

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Providing and laying in position , standardised concrete mix M-25 grade in accordance using 20mm with IS:456-2000 ,and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350kg/ms and maximum water cement ratio of 0.5, including admixture (plasticiser/super plasticiser) in recommended proportions as per IS:9103 to accelerate , retard setting of concrete , improve workability without impairing strength and durability with about 5 cu.m 7730 kg of 20mm machine crushed stone jelly and with about (3.3 cu.m) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7676kg of sand but excluding cost of reinforcement grill and fabricating charges , centering and shuttering and also including laying , vibrating with mechanical vibrators, finishing , curing, etc. and providing fixtures like fan clamps in the RCC floor/roof slabes wherever necessary without claiming extra , etc complete complying with standard specification and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No seperate payment will be made by the department for the excess usage of materials).

Foundation and basement

For Ground floor upto 4.5m

For First floor upto 4.5m to 9m

For Second floor 9m above

Brick work in following Cement Mortar using best quality II Class Table Moulded Chamber Burnt Bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction..

for foundation and basement

For Ground floor

For First floor

For Second floor

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as R.C.C. floor slab, roof slab, beams, lintels,bed blocks,landing slab,waist slab,portico slabs and beams,etc

For Column footings, plinth beam bed blocks templates staircase, steps piers raft beam raft slab etc.,

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick partition walls of 11.50cm thickness using best quality country bricks of size in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

first floor

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (one cement three sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of sizes 300MM X 450 MM set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Supplying and fixing over the hard base with Anti-skid tiles (STEP) 300x300x18 mm thick of any colour with cm 1:3, 20 mm thick and pointed with same colour cement added with colour pigments etc., complete including curing, cutting, wastages etc.,

Providing & Fixing Staircase hand rail made out of 50.80mm dia stainless steel tube of 1.60mm thick at required locations to a height of 1000mm from finished floor level, welded to 38.10mm dia S.S.tube post of 1.60mm thick as vertical at 1m centre to centre with 3 nos of 25.40 mm dia horizontal S.S.tubes of 1.60mm thick in between as per details shown in the drawing and as directed. Rate shall include for grouting into concrete with necessary supporting arrangements in hand rail vertical and in floor, welding the base cup of post into slab reinforcement polishing.buffing and protecting the hand rail surface etc.complete as directed by the departmental officers.

Cement Concrete 1:2:4 (One Cement, Two sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls,

Proving the top of roof with Solar Reflective Ceramic tiles (Required Design) of size 305x305x7cm of approved quality laid in cement mortar 1:3, 12mm thick mixed with 2% water proofing compound (conforming to Indian Standard specification) by weight of cement used and pointed with the same mortar including mixing of red oxide etc. complete.

Supplying and fixing in position best approved quality of PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160 mm dia

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Manufacturing, supplying and fixing in position steel ventilators, N type ventilators using Z sections, J sections for centre mullion, 12mm square rods as per design and providing circular openings for exhaust fans including supplying and fixing 3mm thick coloured glass with necessary weldmesh between the horizontal opening in N type ventilators complete.

Manufacturing, supplying and fixing M.S. grill for Windows and Gate etc, including priming coat

Fabrication, supplying and fixing of Steel door made out of 40x40x6mm M.S. angle section @ 3.50 kg/m used for outer frame and shutter made out of 35 x 35 x 5 mm M.S. angle section @ 2.60 kg/m with necessary stiffener 32 x 6mm. A tie bar of 32 x 6mm M.S. flat is used in bottom of frame in order to avoid twisting of door frame. The shutter and provided with required locking facilities and M.S. furniture fittings such as hold fast, hinge, tower bolt and aldrop. The cost is inclusive of cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls/ concrete if necessary, fixing and finishing the dismantled portion or original condition etc., complete complying with standard specification and as directed by the departmental officers.

Painting New Iron works for grills and steel balustrades etc. with two coats of approved quality and colour of synthetic enamel paint over existing priming coat etc. including scrapping and preparation of surface and cost of brush, scaffolding and complying with standard specification (The quality and colour of paint to be approved by EE before use on works).

Providing Anti – termite treatment to soil adjacent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stage to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport & storing etc., complete and as directed by the departmental officers.(The chemical should be got approved by Executive Engineer before use on work). Stage -1 : Spraying Anti –termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation. Stage-2 : Spraying Anti –termite chemical solution to the grade beam level, spraying has to done for to grade beam brick masonry contact with the back fill earth. Stage-3 : Spraying Anti –termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out and sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring throughout. Stage -4 : Spraying Anti –termite chemical solution alround building outside by making holes with crow bar before laying plinth protection and the holes to be close after the treatment.

Suplying and fixing of MS Lader height of 7.2m length using main frame 50 x 50 x 6 mm (4.7kg/m) L angle and footrest in 35 x 35 x 3mm L angles at the interval of 30 cm center to center and necessary handrails in 50mm dia ms pipe at suitable supports from the main frame and suitabe painting, includes cost of materials, lobour charges, fixing charges, fabrication charges, etc all complete.

Providing expansion joint of 12.5mm width RCC roof slab between rcc twin beams using pvc water bar of 150mm wide with centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with non absorbent flexible and well compressible filler materials of approved quality and covering the top surface with gi sheet 30cm wide 1.6mm thick using phill plugs GI screws ,impet cup washers,bitumen washers etc... complete complying with standard specification.

Providing and fixing in position M.S Rolling shutters of approved make made of required size 18 gauges MS locks interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets side guides and arrangement for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long unispring 2 and MS top cover of required thickness for rolling shutters.

Constructing rain water harvesting pit of size 1.5 x 1.5 x 1.2 m in B.W 23 cm thick wall with necessary earth work, using cm 1:5 foundation sand filling 10 cm thk, pcc 1:5:10 10 cm thk, size 1.5 x 1.5 x 1.2 m and necessary inner and outer plastring with cm 1:5 12 mm thk, and filling with filter media 30 cm thk of sand, coarse aggregate and rcc cover slab 20 mm thk., excluding cost of reinforcement

Supplying, laying and jointing UPVC Pipes of approved quality and best variety of the following dia including labour fixing UPVC Specials, (excluding charges for cutting and threading of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, thread balls, shellac, etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessray brick work / concrete and plastering wherever necessry with necessary scaffolding charges. complete in all floors complying with standard specification. UPVC pipes shall be got approved by the Executive Engineer before use on works. Above ground level. (External Water Supply)

32mm dia UPVC Pipe

25mm dia UPVC Pipe

20mm dia UPVC Pipe

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

20mm dia

25mm dia

32mm dia

Supplying and fixing in position the following UPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of GI pipes, jointing the GI specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification. (The GI specials should be got approved by the Executive Engineer concerned before use on works.)

32mm dia UPVC Bend

32mm dia UPVC Tee

25mm dia UPVC Tee

20mm dia UPVC Tee

32mm dia UPVC Elbow

25mm dia UPVC Elbow

20mm dia UPVC Elbow

32x25mm dia UPVC Elbow

25x20mm dia UPVC Elbow

20x15mm dia UPVC Elbow

32x25mm dia UPVC Reducer

25x20mm dia UPVC Reducer

20x15mm dia UPVC Reducer

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws,

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position best quality PVC soil waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia:

110mm dia:

Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements a. 75mm dia: b. 110mm dia:

PVC Bend

PVC Door Elbow

PVC Tee

PVC Bend

PVC Door Elbow

PVC Tee

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT. the tank is meant for outer (or) indoor, use complete with removable hinged top locking arrangements and to make provision to fix with simply pipe lines necessary manhole with cover and including all PVC specials, plugs, screws, nails to fix the tank etc., and the tank should be fixed firmly as directed. The rate shall inclusive of all materials labour, conveyance, hoistings and fixing charges etc., (The water tank should be got approved by the Executive Engineer before use on works by the dept., Officers.

Supply, Erection, Testing, Commissioning and Handing over of 1No 2000KG Goods lift as per following technical specifications including all taxes and duties Technical Specifications: 1. Location:District Drug warehouse at Thanjavur. 2. No of Lift: one No. 3. Type of Lift: Gearless without Machine Room. 4. Capacity of Lift :Goods lift. 2000 Kgs) 5. Speed:0.03 mtr / Sec 6. Type of Drive: Microprocessor based specific variable voltage variable frequency V3F with enhanced ride comfort and near zero leveling functions. VVVF Drive. 7. No of floor: Ground + 1floors. and 6m 8. Total Travel: 19.2 mtrs approximate 9. Leveling Accuracy: High level accuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of Stainless Steel hairline finish No.4 hair line finish & panels with Direct lighting and New Beautiful Single Tile false ceiling with Tubular Handrail and mirror. 11. Position of Machine: Directly above the lift well shaft gearless. 12. No. of Landing Entrance: One in front - 5 Nos only. 13. No. of Car Entrance: One in front only. 14. Car Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel operated centre opening SS cars. 15. Landing Entrance Door: Centre opening automatic power door with stainless steel No.4 Hair Line finish with view panel Power operated V3F Drive Centre opening stainless steel No.4 Hair line finish with view panel . door with provision for emergency key opening at all landing. 16. Car size: 1600mm widex 2400mm deep (part 1) 17. Car clear Opening: 1200mm x2000mm (as per IS 14665 (part 1) -2000 (wide) x 2000mm Height. (as per IS 14665 (Part-I)-2000). 18. Lift well : 2400mm(width)x3000mm (depth) (as per IS4665 part-1) 19. Lift pit depth available: 1600mm 20. Power supply : 415V,400/440v, 3 phase, 50 cy / Sec A.C supply for power and 230V, 50 Hz single phase AC supply for light. 21. Control: Micro processor Computer based - simplex collective full collective logic system with or without attendant mode. 22. Car fittings:Indirect fluorescent light & Fan. 23. Lift Well: RCC construction with Brick masonry existing. 24. Lift Machine Room: As per standard specification 1800mm (Width) x 1500mm(depth) (as per IS 14665 (Part-5) - 2000) 25. Induction: Up / Down Digital Direction scroll type and position indicator for all landing and in car. 26. Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 27. Emergency Light: Battery operated Light to be provided with automatic charging device. 28. Fireman's switch: To be provided at ground floor. 29. Minor Builders Work: To be provided by lift contractor. 30. Scaffolding: To be provided by lift Contractor. 31. Stainless Steel still angles and facia Plates: To be provided by lift contractor. 32. Steel for lift Machinery: To be Provided by lift contractor. 33.Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarntee period of one year 34. Provision of 1+3 EPABX intercom with phone to be provided at the following places vide 1. Lift Head Room 2. Reception Room and 3. Inside the Lift by lift contractor. 35.Lift License: Preparation of drawing , payment of charges to CEIG and insurance policy if any and obtaining CEIG safety certificate and lift license as per lift act should be done by the lift contractor. 36. Automatic rescue device: To facilitate the landing of the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger inverter under voltage protection system etc. 37. Fire proof can with stand for 2 hours.38.Disable friendly feature are addted as per disable act SOR rate (2021-22) (Make : OTIS/KONE/Johnson/Eq)/

SABARI DHARAN ENGINEERING CONTRACTOR

MNM CONSTRUCTION

SARAVANA ASSOCIATES

VARGEESH CONSTRUCTION