GE/CHM-15/2025-2026 REPAIR AND MAINT OF BLDGS OF MINOR UNIT INCLUDING STN HQ, DCSC, WKSP UNDER AGE B/R I AT CHANDIMANDIR

Amount

Demolition of un-reinforced cement concrete of any description, in any position not specifically provided for, complete all as specified and directed.

Two coats of Acrylic based polymer modified cementious liquid compound (@0.242 Ltr /Sqm) Mixed with cement & ( @ 0.484 Kg/ Sqm) to the floor/ wall surfaces , complete all as specified and directed. Note : second coat shall be applied after 4 hrs of first coat completed

Plain cement concrete 1:5:10, nominal mix, type E-2 using 40 mm graded stone aggregate as in sunken portion complete all as specified & directed.

Demolition of mud phuska as in roof of any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof) complete all as specified & directed.

Dismantling of existing brick tiles or terracing tiles single layer on roof grouted in cement mortar including removal of any existing treatment complete all as specified & directed.

PCC 1:3:6 type C-1 (using 20m graded crushed stone aggregate) as in roof padding, sub base, finished fair and even without using extra cement, complete all as specified and directed.

15mm thick (average thickness) rendering on roof surfaces inclduing flashings and junction of parapets etc finished even and fair in cement mortar 1:4 using water proofing compound as per manufacturer's instruction after brushing cement slurry complete all as specified and directed

Supply only Integral waterproofing compound, all as specified.

3mm thick Atactic polypropylene polymer (APP) modified prefabricated five layer water proofing membrane, based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, over primer coat bonding material of blown bitumen 85/25 grade heated to working temperature of 180° C applied @1.2Kg/Sqm. The membrane shall be laid using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions and finished with applying one coat of bituminous aluminium paint @100gm/sqm on top of membrane, complete all as specified & directed.

40mm thick brick tiles over and including 15mm thick Cement mortar 1:4 joints, grouted & pointed flush as the work proceeds mixed with crude oil 5% by wt of cement complete all as specified and directed.

All as per item No 10 here-in-before but except tiles.

Demolition of plain cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position complete all as specified and directed.

Providing precast cement concrete 40mm thick RCC Jallies in (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate, (measured solid), including all mouldings but excluding frame set in cement mortar 1:4 Complete all as specified and directed.

Reinforced cement concrete 1:2:4 Type B-1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, balconies, roofs, canopies shelves and the like complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed ) not less than 0.9 mm dia all as directed and specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviveable tiles to store and rubbish off the premises complete all as specified and directed

Non skid ceramic coloured tiles, joint free, first quality, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.09 Square metre but not exceeding 0.18 Square metre, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles 7mm thick in vertical surface like skirting, dedo of area exc 0.13 sqm but not exc 0.27 sqm complete, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over a 15mm thick rendering in cement mortar 1:6 complete all as specified and directed

Coloured vitrified ceramic tiles, 7-10mm thick (square/rectangular ) , area of each tiles n.exc 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base finished fair and even without using extra cement, complete all as specified and directed.

Steel window, box type, in repair primer coated, 1.00mm wall thickness, with glazing bar and openable shutter prepared to recieve sheet glass, complete including cutting holes, four Nos. for each window and making good dismantled portion in PCC (1:2:4) type B-1. including following fittings welded to frame/ shutter complete all as specified and directed.:- (a) Hold fast 150mm out of 25x6mm flat iron made to shape- 04 Nos. each window (02Nos. on each side). (b) Handle of 'Z' section 20mmx25mm, 100mm long- 01No. each leaf. (c) MS tower bolt 150mm long- 02 Nos. each leaf. (d) 'Z' section 20mmx25mm, 100mm long stopper 01 No. each leaf. (e) Cleat 55mm long of hollow square section 15mmx15mm of 24 guage wall thickness, welded to hinge of 55mm size 01 No. per leaf. (f) MS box type hinges of 75 mm size- 02Nos. per leaf. (g) Fabrication & fixing complete. Note: Glass panes & painting shall be measured & paid separately under respective item.s. Design shall be approved from Engr-in-Charge as existing at site and all as per Drawing before fabrication and bulk order to the manufacturer.

All as per serial item No 22 hereinbefore but without glazing bar.

Steel ventilator factory made with top hung shutter including hinges, steel peg stay, a shop coat of red oxide primer, fixed as in repairs complete all as specified and directed.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290-0 or Fe 165-0, all as specified and directed.

Taking down chowkhats or frame n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) complete all as specified & directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm with shutter (without taking off shutters from the frame) complete all as specified & directed.

Factory made pressed steel frames having profile 105mm x 60mm for doors with one or more rebates made out/fabricated of 1.25 mm thick MS sheet, including necessary fixing lugs, hinges, lock strike plate, thress hold bar/flat etc. including filling PCC 1:3:6 complete all as specified & directed.

Pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, including filling of PCC 1:3:6 in hollow frame complete all as specified and directed.

30mm thick flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides all as specified & directed by Engineer-in-charge.

Glazed and gauged skelton shutter (Factory made) 30mm thick of second class hard wood (Hollock) open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated, a shop coat of pink primer complete all as specified & directed.

30mm thick, factory made, second class hard wood, plain framed, panelled shutter (two panel)with lock rail and panel of 9 mm BWP commercial ply both face including 1.00 mm thick sunmica (lamination) on both sides of p-anel and 20 mm x 20 mm x 10 mm wooden beading all round the panel. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed.

Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, complete all as specified & directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specifications & drawing complete all as specified and as directed by Eng-in-Charge.

Flush shutters 25mm thick factory made solid core construction with particle board core and ply wood face panels, commercials type on both sides, complete all as specified & directed.

150mm long aluminum handle cast type anodized, fixed as in repair complete all as specified.

150 mm size aluminium anodized , barrel tower bolt of extruded section, fixed as in repair complete all as specified and directed.

Aluminum alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy, fixed as in repair complete all as specified and directed.

100mm size, butt hinges, medium weight, cold rolled mild steel cmplete all as specified & directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Powder coated aluminum sections as in frames/ shutter of doors/window/ventilators /partitions, (Sliding / openable/ three track) including joinging cleats, glazing clips, rubber neoprene beading, powder coated aluminim snap beading, screws etc. complete all as specified and directed Note : (i) Minimum thickness of power coating shall not be less than 50 micron. (ii) Weight of aluminum section only shall be measuerd and paid. (iii) Aluminum doors/windows /ventilators to be fixed to jambs with chromium plated screws . (iv) The rate shall be inclusive of neoprene beadings, snap beading, screws etc and in case of sliding shutters locking arrangement and rollers in sliding shutters. Weight of fitting fixtures will not be measured for arriving the weight of aluminum section. (v) Glass /wooden panel/ACP sheet shall be measured and paid separately under respective items. (vi) Design as directed by Engineer in charge.

Repair to old aluminium door/window including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285 ,(Excluding aluminium material for shutter frame ) fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, including dismantling & refixing of door if required complete all as specified and directed by Engineer-in-Charge. Note : (i) Glass panes and panels shall be measured & paid separately under respective items (If required).

5.00mm thick ordinary quality tinted glass, fixed to aluminum frame work ,in panels exc 0.5 Sqm in each pane, complete all as specified & directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden, metel frames including punching or drilling out glazing pins/spring clips complete all as specified and directed.

3mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples, complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples, fixed as in repair complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, all as directed.

Steel work in tubular trusses and tubular posts including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 t complete all as specified & directed by Engineer-in-Charge

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, inclcuding dismantling of existing corrugated sheet complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, inclcuding dismantling of existing corrugated sheet complete all as specified and directed.

Steel rolling shutters (1 mm thickness of lath) with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete, gear operated type with bevel gear box and crank handle, fixed as in repair complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red oxide, zinc chrome complete all as specified and directed.

4mm thick False ceiling fibre cement board, white in colour , 595mm x 595mm in size, fire and moisture resistance, fixed with and including standard GI snap grid framing (Powder coated) and suspended not exceeding 900mm below from ceiling with 3mm dia wire including clips and misc fittings etc in pattern as approved by GE, fixed as in repair (size of panel shall be of 605 x 605mm and GI snap grid framing shall be of 1mm thick standard section i.e. channels, angles, tee etc), fixed as in repair complete all as specified and directed.

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) With Semi preforated 12mm thick micro tegular edged GRG false ceiling tiles, false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99% NRO .05 to 0.75 as per IS 8225:1987, Non-combustible as per BS 476 (part4)- 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides ) comprising of main- T runners of size 15 x32 mm of length 3000mm, cross-T of sixe 15 x 32 mm of length 1200mm and secondary intermediate Cross-T of size 15 x 32mm of length 600mm to from grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of the Engineer-in-Charge.

Demolition of plain cement concrete in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified and directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

Factory made Rubber moulded vibro compacted machine pressed cement concrete interlocking pre polished paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning, including dismantling of old tile complete all as specified and directed

Factory made Rubber moulded vibro compacted machine pressed cement concrete interlocking pre polished paver block, with grey cement and pigment, design as approved, any shape and size conforming to IS 15658-2006 of 80 mm thickness, M-35 Grade laid over and including 25mm thick sand cushioning, including dismantling of old tile complete all as specified and directed

Factory made Rubber moulded vibro compacted machine pressed coloured chequered cement concrete tiles 300mm x 300mm x 25mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid over and including 20mm thick screed bed in cement mortar 1:4, including dismantling of old tile complete all as specified and directed

Coloured non skid porcelain tiles exterior grade 300x300x 8-10mm thick heavy duty (Endura from Johnson or equivalent) as in floor, set and jointed in neat slurry and pointed in coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar 1:6, including taking out of old tiles, complete all as specified and directed Note for serial item No 59 to 62 : Colour / Design as approved by Engr-in-Charge

PCC 1:3:6 type C-1 (using 20m graded crushed stone aggregate) as in side kerbs, ramp and like, finished fair and even without using extra cement, complete all as specified and directed.

500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, 02 Nos GI unions and 02 Nos check nuts, ball valve, dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed by Engineer-in-charge.

1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) triple layered, screwable lid, hoisted and fixed in position, including tank nipple, 02 Nos GI unions and 02 Nos check nuts, ball valve, dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed by Engineer-in-charge.

2000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, screwable lid, hoisted and fixed in position,including tank nipple, 02 Nos GI unions and 02 Nos check nuts, ball valve, dismantling of existing water tanks and removing from site all as specified in SSR Part-I and all as directed by Engineer-in-charge.

Cleaning and removing all scale, silt , mud or dirt from overhead water storage tanks of capacity exc 500 litres but n.exc. 1000 litres and mouths or circulating pipes , complete all as directed.

Cleaning and removing all scale, silt , mud or dirt from overhead water storage tanks of capacity exc 100 litres but n.exc. 2000 litres and mouths or circulating pipes , complete all as directed.

Float valve/ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed for 20mm bore pipe (minimum weight 210 gms), fixed as in repairs, complete all as specified and directed.

15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors , including taking up or down existing GI tubing and removal to store complete all as specified and directed.

20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors , including taking up or down existing GI tubing and removal to store complete all as specified and directed.

Bib tap standard, 15mm bore of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-105gms), fixed as in repairs complete all as specified and directed.

Bib tap, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed both and for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

20mm bore Gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repairs, complete all as specified and directed.

Grating round 140mm dia of cast copper alloy chromium plated complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm with and including CP waste coupling, angle brackets, PVC connection 15mm size, 450mm long, PVC waste pipe, fixed as in repair complete all as specified and directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect, fixed as in repair complete all as specified and directed.

Brass chromium plated, tubular towel rail 20 mm dia. ‘D’ type, 60 cm long between flanges, fixed as in repair complete all as specified and directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty , fixed in repairs complete all as specified and directed.

Floor door stopper of brass body and tongue, anodized with hard drawn steel spring, fixed in floor (140mm size), fixed as in repair complete all as specified and directed.

Door closer hydraulically regulated of aluminium extruded section, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg, fixed as in repair complete all as specified and directed.

25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

Single piece EWC (one piece), minimum size 715 x 335 x 715mm, , snow white colour, S-trap with integraed flusing cistern, including slim soft close seat cover , fixed as in repairs, complete all as specified and directed.

Vitreous china, wash down water closet pan, superior white, Pedestal pattern WC with ‘P’ or ‘S’ trap, seat cover (excluding, flushing cistern and flush pipe), fixed as in repairs complete all as specified and directed.

Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest (excluding flushing cistern and flush pipe) including makes connection to trap & flushing pipe, set in cement concrete and making good to the floor, fixed as in repair complete all as specified & directed by Engineer-in-charge.

PVC seat cover square / circualr in shape, soft closed type for EWC with hinging arrangement fixed as in repair complete all as specified & directed

Supply and fixing vitreous china bowl urinal flat back, size of 465 x 355 x 265mm white (Minimum) with urinal spreader, urinal coupling and discharge pipe including providing & fixing plugs, waste pipe, bedding urinal against wall in CM 1:2, including Urinal Pipes, securing urinal to plugs screws, pointing around urinal to plugs screws, pointing around urinal back in white cement.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including PVC connection with PTMT nuts and 32mm dia CP flush pipe (long type for squatting pan), fixed as in repair, complete all as specified & directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm fixed in repair, complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. complete all as specified and directed.

15mm thick rendering in Cement and Sand mortar 1:6 over concrete /brick surfaces finished even and smooth without using extra cement, complete all as specified & directed.

15mm thick rendering in Cement and Sand mortar 1:4 over brick or concrete surfaces finished even and smooth with using extra cement, including providing necessary scaffolding, safety precautions and other requisite requirements complete all as specified.

Preparation of old surfaces of any description of walls,facia, ceiling, RCC etc and applying two coats of oil bound distemper over one coat of wall primer complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

10mm thick rendering in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement complete all as specified and directed

Preparation of new plastered/RCC ceiling surfaces and applying three coats of white wash complete all as specified and directed

PVC (SWR) rain water pipe, 110mm bore, single socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, including taking down old existing pipe complete all as specified and directed.

110 mm bore PVC (SWR) bends of any radius complete, and making good the disturbed surface with cement mortar 1:4 all as specified and directed.

PVC (SWR) waste pipe, 75mm bore, single socketed in any length with cement/ rubber ring joints, laid in trenches or in floor or fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, including taking down old existing pipe complete all as specified and directed.

75 mm bore PVC (SWR) bends of any radius complete, and making good the disturbed surface with cement mortar 1:4 all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors laid, bedded and pointed in any mortar including disposal of demolished material n.exc 1.5 km complete all as specified and directed.

Granite slab 15mm thick (of any type & shade as approved), as on cooking platform, counter slab etc (length and width as ordered by GE in one piece) best quality machine cut and jointed with grey cement slurry and pointed in white cement mixed with pigment to match the shade of slab laid over and including 15mm thick screed bed in cement mortar 1:4 including nosing at edges, rounded edges complete all as specified and directed.

Kota Stone Slab flooring, 16-18mm thick, best quality over and including cement screed bed 15mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including cutting, rubbing, grinding and polishing (Mirror finish) complete all as specified and directed.

All as per serial item No 108 hereinbefore but on skirting / vertical surfaces laid over and including 10mm screed layer in cement mortar 1:3, cutting, rubbing, grinding and polishing complete, all as specified.

Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, over and including 15mm thick screed in cement mortar 1:6 complete all as specified and directed.

Sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 510mm x 430mm bowl size 430mm x 380mm x 203mm fixed as in repair compelte all as specified and directed.

2mm thick fibre glass reinforced translucent plain coloured sheeting with side lap, fixed with coach screws as in roof, wall etc, fixed as in repair complete all as specified and directed.

4mm thick aluminium composite panel sheet (ACP) fixed with aluminium beading with rubber gasket including all necessary clips and fittings colour as approved by Engr-in-Charge all as specified and directed.

Wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and directed

15mm bore pillar tap, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, fixed in repair, complete all as specified and directed.

Stop valve (concealed type), chromium plated, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Preparation of old surfaces of walls and applying two coats of cement base paint, complete all as specified and directed

Preparation of old surfaces of walls and applying two coats of oil bound distemper, complete all as specified and directed

Preparation of old surfaces of any description of facia, ceiling, RCC etc and applying one coat of oil bound distemper over one coat of wall primer complete all as specified and directed.

One coat of exterior emulsion paint on existing external plastered or unplastered surface of building over one coat of exterior wall primer (all as per manufactures instructions) complete all as specified and directed.

Two coats of exterior emulsion paint on existing external plastered or unplastered surface of building over one coat of exterior wall primer (all as per manufactures instructions) including complete removal of existing treatment complete all as specified and directed.

Applying Wall care putty (average thickness2mm as required for desired smoothness and leveling of surfaces in two or more layers) and sand papering for making the surfaces even and smooth complete all as specified and directed.

Hard core of broken stone or boulders of gauge n.exc. 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified & directed.

10mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holeswith necessary screws/ beading, rubber packing, L Patch bottom and top, self clossing patch etc complete all as specified and directed.

Mortice lock, verticle type, mild steel, 4 levers, size 100mm, brass body, complete all as specified and directed

300 mm long stainless steel handle, fancy type , fixed to toughened glass, complete all as specified and directed.

Grinding and polishing surfaces of old Kota/marble/granite stone flooring, skirting etc by grinding machine, dusting off the surfaces after grinding, washing and mirror polishing complete all as specified and directed by Engineer in Charge

Dhingra Brothers (BID ID -3304990)

Gunjan and Gunjan Associates (BID ID -3306372)

M/s Super Trading Corporation (BID ID -3305888)

MS R G ENTERPRISES (BID ID -3305458)