PROVN OF TOILE BLOCK FOR JCO/OR NEAR GEPTA, SPECIAL REPAIR TO BLDG NO. T-18 MT GARAGE AT GRC AND PROVN OF AIR DUCT COOLING SYSTEM FOR BLDG NO. T-01A PATIENT DUINING HALL OF MH KAMPTEE UNDER GE KAMPTEE.

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding and disposal of rubbish outside of MD land complete all as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding0.06 but not exceedig 0.11sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM (1:4) finished fair and even for laying floor finishes/ tiles etc complete all as specified and directed.

M&L for coloured glazed ceramic wall tiles 300 x 450 x 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles including rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 as backing coat to receive wall tiles/skirting/dados complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including ashlar facing dressed stone and pre-cast concrete articles complete all as specified and directed.

M & L for brick work with fly ash bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6(Using old size brick) complete all as directed.

All as per item No 05 here-in-above but half brick wall in CM 1:4 complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls/chajja/pillars etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for rendering 15 mm thick in two coats (10 and 5mm thick) in cm 1:4 on brick or concrete surfaces even & smooth, using water proofing liquid compound and without using extra cement complete all as specified and directed. Note: water proofing liquid will be measured and paid separately.

M & L for rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed..

Supply only liquid integral water proofing admixture of make pidilite or its equivalent complete all as directed.

Material & labour for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of cement primer complete all as specified and directed

M & L Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall care putty complete all as specified and directed

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over coat of primer complete all as specified and directed

S & F 100 mm long Mild steel medium weight cold rolled butt hinges and fixed with screw/welded to frames etc all as specified and as directed

S&F 125 mm Extruded Aluminium handles fabricated type anodised etc complete all as specified and directed

S & F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed etc complete all as specified and directed.

S & F 150 mm long aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed

S&F Aluminium anodised barrel tower bolts of extruded section and fixed of 100mm long complete all as specifed and directed.

M&L for providing and fixing snap grid for false ceiling non asbestos board of size 595x595mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel section @ 90grams/sqm, both side inclusive) consisting main ''T'' runner with suitably spaced joints to get required length and of size 24mmx38mm made from 0.25mm thick (minimum) sheet, spaced at 1200mm centre to centre and cross ''T'' of size 24mmx25mmx1200mm made of 0.25mm thick (minimum) sheet,1200mm long spaced between main spaced between main ''T'' at 600mm centre to centre to from a grid of 1200x600mm and secondary cross ''T'' of length 600mm and size 24mmx25mmx600mm made of 0.25mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.4mm including, required cutting/making, opening for services like diffusers, grills light fittings, fixtures , smoke detectors etc, Maint ''T'' runners to be suspended from ceiling using slotted cleats of size 27x37x25x1.0mm fixed to ceiling.4mm GI adjustable rods with galvansied butterfly level clips of size 85x30x0.5mm spaced at 1200mm centre to centre along main T , bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specification, as directed.

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework fixed in ceiling flat or sloping complete all as specified and directed.

S& F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed.

S& F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed.

Material & labour for PCC (1:3:6) Type C1 (using 20 mm graded stone aggregate), 75 mm thick as in plinth protection and finishing surfaces even & smooth without using extra cement including mist filling in the joint complete all as specified and directed.

M & L for Plain Cement concrete 1:4:8 type D2 (40mm graded aggregate) as in foundation, mass concrete in sub bases/pavings etc complete all as specified and directed.

M & L for Hardcore of gauge n exc. 63 mm Broken stone or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed .

M & L for chequred cement concrete tiles colour glessy finished rubber pressed 30 cm x 30 cm x 25 mm thick set jointed and pointed in neat cement slurry and pointed in coloured pigment over 20mm cement screed bed in cement mortar 1:6 complete all as specified and directed.

S & F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood grain colour (or match with shutter) PVC sheet reinforced with MS square tube opening as per drawing complete all as specified and directed.

S&F 30mm thick factory made solid PVC panelled door shutter (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet strip of 20mm width struck inside with solvent cement for styles and plain colour PVC sheet for top rail, both rail of bottom rail on either side & as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the style and rail with suitable PVC sheet beading and jointed together with solvent cement etc fixed with frame at site complete all as specified and directed.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings omplete all as specified and directed.

Supply and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete as per architectural drawings omplete all as specified and directed.

S&F for sheet glass 5.50 mm thick exc 0.50 sqm in each panel, tinted quality and glazing complete all as specified and directed.

Taking down door / window frame with shutter (without taking off shutter from the frame) area not exc 1.5 sqm complete all as specified and directed.

Taking down door / window frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but not exc 4 sqm complete all as specified and directed.

S&F35mm thick Flush door shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides face is covered with both side decorative face veneer with lapping/frame to match complete all as specified and directed.

M&L for mild steel angle iron as in framed chowkats for door shutters cut to length including necessary welding and making holes for fixing butt hinges and fixing 10 mm dia as tie bar complete confirming to Fe-410 -W (Gde E-250) quality A etc all complete all as specified and directed.

S&F angle iron frame work for placing desert cooler including anchor bolts (fastners of 8mm dia and 100 mm long) and all necessary drilling, welding, bolting or riveting, etc. and similar work and fixing to the required location and position inclduing shape and size conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, eatherings,throat- ing etc. and setting in mortar complete with joints to match etc complete all as specified and directed.

S&F for 25mm dia curtain rod of approved quality including all fittings & fixtures, cutting and fixing to curtain brackets complete all as specified and directed.

Surface dressing n.exc (not exceeding) 15 cm deep and averaging 15cm deep and getting out etc complete all as specified and directed.

Excavation in trenches n exc 1.5m in deepth and 1.5m in width and getting out in hard /dense soil complete all as specified and directed.

Excavation in trenches n exc 1.5m in deepth and 1.5m in width and getting out in any type of soil for laying of cables, laying of pipes and geting out excavated material complete all as specified and directed.

All as per item No 41 here in above but each additional 1.5 m or part thereof in depth beyond the first 1.5m all as specified and directed

M&L for Form work to side of concrete in fdns, footing base, base of columns, side and soffits of plinth beam and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) as in footing, foundation, beams, plinth beams,lintel beams base for columns and mass concrete etc complete all as specified and directed.

M&L for Form work to side of columns and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) as in columns and pillars etc complete all as specified and directed.

M&L for Form work to chullah hoods, chajjas, / Lintels /Beamstroughs and similar items including edges and simillar work complete all as specified and directed.

M&L for providing RCC 1:1 1/2:3 type A-1 (nominal mix) (using 20 mm graded stone aggregate) as in chajja/ Lintel/Beams etc complete all as specified and directed.

S&F mild steel TMT bars 10 mm dia and over , cut to length, bent to shape requred, including crancing bending and binding with mild steel (anneal) wire not less than 0.90mm dia complete all as specified and directed.

S&F mild steel TMT bars 8 to 10 mm dia a as in stirrups, spacers and binders complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and directed.

M&L for 75 mm thick Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base to floors finished even complete all as specified and directed.

M & L for 40 mm Damp proof course in 1:2:4 type B0 (using 12.50 mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 4mm thick moulded laminated PVC Sheet on the front face & 4mm plain colour PVC sheet on back face, with wood free EPS supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

M&L for 4.0 mm thick frosted sheet glass ordinary quality and glazing with oil putty in square n.exceeding 0.5 Sqm in each panes complete all as specifed and directed.

M & L 20 mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S &F Towel Rack with lower hangers 600 mm long 20 mm dia of Chromium plated fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specifed and directed.

S&F tubular towel rail, 20mm dia, D type, 60cm long between flanges chromium plated complete all as specified and directed.

S&F toilet paper holder complete all as specified and directed.

S & F white Vitreous china wash down water closet pan (pedestal pattern) including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts (excluding flushing cistern) etc complete all as specified and directed .

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed .

S&F Vitreous China wash basin table top , white, flat back, excluding taps,waste, chain and plug and porcelain stopper but including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed, complete all as specified and directed Jaquar KUS WHT 35901

S & F chromium plated shower square (200mm x 200mm) rose with or without swivel joints incl shower arm as approved complete all as specified and directed.

S&F Stop valves/angle cock, cast copper alloy, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions and fixed fancy type chromium plated complete all as specified and directed.

Supplying and laying of CPVC pipes 16 mm diaSDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified.

As per item no 66 above but 20mm bore complete all as specifed and directed.

Supply & Fix Sink Mixer/ Pillar taps with swinging spout ( Table Mounted Model) withy 450 mm Long Barided Hoses, cast copper alloy, with capstan heads,chromium plated (fancy type),screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed,complete all as specified and directed. Cat Part No Jaquar CQT-233098 or equivalent.

S&F Vitreous China urinals Size 375x320x620 including urinal spreader complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe,with bottle trap, CP grating and Union for discharge pipe,complete all as specified and directed. Jaquar URS WHT-132530 or equivalent.

S & F Urinals Partition curved shaped with frosted glass 10 mm thick complete all as specified & directed Jaquar JSE-CHR-810Uc450X or equivalent.

S & F faucet of 15 mm bore brass chromium plated including PVC pipe to connection GI tubing 15 mm bore all complete all as specified and directed. Make: Prayag cat no BEA-40 or equivalent.

S&F glass shelf 500x125mm with brackets complete all as specified and directed. Make:- Prayag Cat No BEA-45 or equivalent.

S&F corner sheet glass shelf assemble consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard and railing complete all as specified and directed. Make prayag cat No BEA 44 or equivalent

S&F 40mm bore of pipe low density polyethylene pipe (LDPE) of pressure rating 6kg/cm fixed complete all as specified and directed.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm , setting and jointing with solvent cement complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipe, single socketed in any length with rubber ring joints, fixed to walls with stack clamp every one mtr apart complete all as specified and as directed.

S&F PVC (SWR) pipes of 75 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specifed and directed.

S&F CP grating of size 100mm x 100mm dia complete all as specifed and directed.

S&F 110mm PVC (SWR) bends any radius with oval access door complete all as specifed and directed.

S&F 75mm PVC (SWR) bends any radius with oval access door complete all as specifed and directed.

S&F PVC cowl slotted vent cowl 110 mm size complete all as specifed and directed.

M&L precast cement concrete 1:2:4 type B1 (using 20mm graded aggregate) as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, mangers, shelves and similar articles with plain faces and set in CM 1:6 . (reinforcement measured and paid sepratly) complete all as specifed and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed.

Removing excavated material (soil) n .exc 50m and deposited where directed at a level n exc. 1.5m above the strating point complete all as specified and directed.

S&F 5mm thick colour/printed designer PVC wall/ceiling sheet instips and channel feathered at the edges for fixing on solid PVC wall/ceiling lining insulated PVC wall/ceiling lining and solid PVC partition inclusive of solvent cement and fixing arrangements (suitable fillet, H-joint, U-end, J-edge, External corner and internal corner, horizontally, vertically or at any height and angle) at site, complete all as specified and directed. Note:- PVC wall/ceiling lining should be reversible, waterproof, washable, rib-reinforced, rigid, standard metal.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tube conforming to IS 1161-1979 grade St-240 complete all as specified and directed

M&L for rolled mild steel sections in rafters, purlins and posts . where connected to common rafters and running rails fixed with angle cleats or other connecting plates and nut, bolts or welding etc. confirming to Fe-410 (Gde E-250) complete all as specifed and directed.

Preparation of newly steel surfaces of any description over 10 cm width or girth & applying two coats synthetic enamel paint complete all as specifed and directed.

S&F Rotational moulded (three layers, ISI marked) polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity including PVC cover, hoisted and fixed in position including connection up pipes complete all as specified in SSR Part I and as directed.

S & F 20 mm PTMT float valve, high pressure with Polythene float and fly nut complete, screwed for Iron pipe etc all as specified.

S&F gun metal gate valve of 15 mm dia with iron wheel screwed both for iron pipe complete all as directed.

S&F gun metal gate valve of 20 mm dia with iron wheel screwed both for iron pipe complete all as directed.

M&L for SGSW drain pipes laid in trenches of 150 mm internal diameter of pipe and jointed as specified complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel girth not exc 30cm in cement concrete using extra cement including form mounds etc all as specified.

M&L for providing precast RCC 1:2:4 type B1(using 20mm gde stone agg) as in cover slabs for manholes set in CM 1:6 ( Note : Reinforcement shall be measured & paid separately) complete all as specifed and directed.

M&L for Brick bats laid dry in Soakage pit complete all as specifed and directed.

Excavation over area, n exc 1.5 m deep and getting out Soft/loose soil including Clearing away all grass vegetation, saplings, shrubs, brushwood, undergrowth, roots, and trees not exceeding 30 cm girth Complete all as specified and as directed.

M & L for 100mm thick Plain Cement concrete 1:4:8 Type D2 (using 40mm graded aggregate) in foundations, filling and mass concrete sub bases/pavings complete all as specifed and directed.

M & L for Sand filling under floorings/pavement spread and levelled in layers n.exc 15cm thick complete including watering and consolidation complete all as specified and as directed.

M & L of Machine pressed precast conctete interlocking paver block colour glessy finished rubber pressed any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade ® with Grey cement and pigment complete all as specified and as directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate as in coping including weathering throating and necessary formwork complete all as specified.

Taking down point wiring with aluminium conductor cable of light point fan & socket light & power complete including light fittings any type switches, sockets, ceiling rose, switch boards, bell/buzzer, bell push, tube light fitting, regulator etc, and making good to the disturbed surfaces of walls/ floor etc to macth with existing surfaces including white washing/colour washing/ distempering to match with existing wall/floor/ceiling finishes, complete all as specified and directed.

Taking down sheet metal enclosure, DB & MCBs main switch etc and making good distrubed sufaces to match with exisiting surfaces, complete all as specified and directed.

Taking down sub main wiring of any size/ capacity complete all as specified and making good disturbed sufaces to match with the existing surfaces, complete all as specified and directed.

Material and labour for point wiring 1100 volt grade single core FRLSH PVC insulated and unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in and including electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marked medium grade concealed on surface of wall/ceiling including FRLSH PVC insulated unsheathed earth wire with multistranded copper conductor of size 1.50 sqmm modular boxes sunk on wall for mounting of any type modular switches, switch sockets, fan regulator etc including modular cover with frame any size complete all as specified and making good disturbed surfaces for one light point controlled by one, one way switch, complete all as specifed and directed. Note :- Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, ceiling roses and holders shall be connected to common earth dolly.

All as per item Sl No 109 above but One ceiling/exhaust fan point controlled by oneway switch and regulator, complete all as specified and directed.

All as per item Sl No 109 above but One 3 pin 5 amp socket outlet point on the same board with other switches, complete all as specified and directed.

All as per item Sl No 109 above but One 3 pin 5 amps socket out let point on independent board, complete all as specified and directed.

All as per item Sl No 109 above but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point, complete all as specified and directed.

All as per item no 109 above but of size 2 x 4 sqmm with earth wire 1 x 4 sqmm complete all as specified and directed

Supply and fixing for switch modular type single pole one way 6 amp 1 module 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing for socket modular type single pole one way 6 amp 2 module 2/3 pin 250 volts AC suitable for modular switchboxes, complete all as specified and directed.

Supply and fixing for switch modular type single pole one way 6/16 amp 3 pin 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing for socket modular type single pole one way 6/16 amp 2/3 pin 2 module, 250 volts AC suitable for modular switch boxes, complete all as specified and directed.

Supply and fixing ceiling rose, surface type, three terminals 5 amps, complete all as specified and directed.

Supply and fixing 0-4 step -2 module modular type electronic regulators for ceiling fan 1200/1400 mm sweep, 240 volts, 120 watts single pole complete all as specified and directed.

Supplying and fixing 18-22 Watt LED Tube light fittings complete with aluminum body including tube rod, driver with not less than 2000 Lumen O/P and I/p rated voltage 240V connecting with 3 core 1 sqmm copper conductor cable complete all as specified and directed.

Supply and fix building security light LED 25 W with Lumen O/P 2500 with driver with rated voltage 240 V, 50Hz,including mounting GI (made out of 25 mm dia light grade pipe 0.8 m bent two shape including FI clamps nut bolts etc. complete all as specified and directed.

Supply and fixing LED light fitting 10W bulk head luminaries with lamp holders etc complete with all accessories and including connecting upto with twin core twisted flexible cable suitable size of 230V, 50Hz complete all as specified and directed.

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed.

Supply and fix MCB single pole & neutral 240 volt 6 to 40 amps 10 KA, complete all as specified and directed.

Supply and fix MCB single pole 240 volt 6 to 40 amps 10 KA, complete all as specified and directed.

Supplying and fixing 20-24 Watt LED Tube light fittings complete with aluminum body including tube rod, driver with not less than 2000 Lumen O/P and I/p rated voltage 240V connecting with 3 core 1 sqmm copper conductor cable complete all as specified and directed.

Supply and fix LED baton fitting 2' length including drivers having energy consumption, 10/11W ,230 V ,50Hz, 6500K, not less than 1000 lumen prewired, complete all as specified and directed.

Supply and fixing round shape COB light warm white 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts cool white AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing Exhaust fan PVC body 225/230mm sweep, single phase, 230 Volts, 50Hz, with louvers and fixing arrangement etc., and connecting up with twin core twisted flexible copper conductor cable of suitable size from fitting to ceiling rose, and making holes complete all as specified and directed.

Supply and fix wall fan 400 mm sweep including mounting frame nuts, bolts, washers etc complete all as specified and directed. Make : Havells model AINDRILA or equivalent, Crompton, Bajaj

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc. complete all as specifieds and directed.

Supply and fix sheet metal enclosure triple pole & neutral for 415V volts 4 way with 200 Amp rated bus bar flush /surface mounting, double door, complete all as specified and directed.

Supply and fix MCB triple pole & neutral 415 volt 32 amps 10 KA, B series complete all as specified and directed.

M&L for Earthing complete with galvanised steet earth plate electrode 600x600x6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanised earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric (d) Funnel with watering pipe of GI 20mm nominal bore light grade and copper lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protec-tion pipe 7.50 metre long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

Supply and fix Double wall corrugated High Density Polymer Ethyl(HDPE) pipe for laying of electric cable of size 50 mm outer diameter and 38 mm inner diameter with IS 14930 (part 2) 2001 and 6mm thickness laid in trenches(Including cutting of roads or any others hard surfaces and making good disturbed surfaces) , wall, poles including bends, sockets and other connected accessories complete all as specified and directed.

Supply and laying in trenches or fixing in walls / poles or drawing through pipe XLPE insulated, screened,PVC bedded, galvanised steel strip or wire armoured,electric power cables ( heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 sq mm,4 core including testing after laid and jointed all as specified and as directed

S & F GI tube light grade for protection of pipe 40 mm dia fixing in ground /poles with all fittings complete all as specified and directed.

S&F GI tubing medium grade with all fittings laid in trenches and fixed complete to wall and ceilings or laid in floors as socket, bends/ elbow, union, tee etc to for 25 mm bores complete all as specified and directed

S&F GI tubing medium grade with all fittings laid in trenches and fixed complete to wall and ceilings or laid in floors as socket, bends/ elbow, union, tee etc to for 20 mm bores complete all as specified and directed

S&F gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed to 25 mm bore complete all as specified and directed.

S&F gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed to 25 mm bore complete all as specified and directed.

M & L for Cutting existing steel tubing 25/32 mm for alterations or additions (Each cut measured) includimg screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector complete all as specified and directed.

Supply, installation, testing and commissioning of Air Cooling Unit of size 6' x6' x6 feet , 20 SWG ,with 4 Inch thick honetpad and MS angle section 50x6 mm, factory fabricated front openable door system suitable for 3 phase 4 wire 415 volts, powder coated painting the complete body internally and externally with two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete including necessary internal wiring with PVC insulated multistrand copper conductor singal core FRLSH cable of suitable size and deliver fresh air, which circulate stale air,With power-saving technology,Reduce temperature , Auto drain /clean function and ,the pad shall completely cover the grill panel includingand Cooler stand made angle 75x75x6 mm thick MS angle iron frame work on PCC 1:2:4 type B-1 platform 40 cm above the ground level and 45 cm below the ground level, completely all as specified and as directed. The cooling unit comprises of following features (a ) High Speed submersible water pump 35 Watt , single phase 240 Volt , maximum lifing of water 2.4 mtr , 0.5 HP , in build thermal over load protector -2 Nos Make- Vansal /Anand /AMDO (b) Fan motor hevy duty copper winding 1200 watt (1.5 HP) , Power 3 phase Make- ALMONARD/ Merathan (c) Cellulose pad 100 mm thick, , As per OEM , (d) Fan Type: fan size:- 36" , RPM :-900 , (e) Tank capacity 300 Ltr complete (f) Air flow -10000 cfm (h) Discharge of Air Flow - Top side (j) Air Pressure 150 P.A (k) Noise(db) - 73 db (l) Air outlet size-1066 mm x1066 mm all as specified and directed by Engr-in Charge.

Supply and installation of GI, Pre fabricated rectangular GI ducts, of 24 SWG, Glavanised Iron Sheet thickness 0.70 mm complete with MS flanges and bracing (as specified), necessary supports using thread rods (as directed) and anchor bolts, supply air collars, vanes, splitters complete all as specified and directed.

Supply, installation, Exhaust air Square Grill of size 48" x12 " with damper with multideflection ( Four Way Deflection) including making good disturbed surfaces complete all as specified and directed.

Supply and fixing of 50 mm Thick Thermocoal / Duct insulation 9 mm cross lean sheet along with lack coating for protect the outside duct with two coats of enamel paint after surface preparation including making good disturbed surfaces complete all as specified and directed.

Supply,& fixing of canvas Flexible Connection for Mouth opening of Air Cooler of size 1066 mm x1066 mm flexible type to S.A. Duct complete all as specified and directed.

Supply, fabrication and installation of MS base frame of MS angle iron and flat iron of suitable size for Air Cooler & Water Tank units complete with epoxy painting, vibration isolation pads, supports, rangers, railing, brackets etc with coats of epoxy primer and 2 supports of black point etc are required. complete all as specified and directed.

M & L for dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet including refixing after complete the ducting cooler work work complete all as specified and directed.

M & L for Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi?nium framework with screwscomplete all as specified and directed.

M & L for civil work including core cut, chieseiling , cutting of wall and making it as original by covering to all duct opening complete including making good disturbed surfaces complete all as specified and directed.

Excavating in trenches not exc 1.5 m wide and not exc 1.5 m in depth for foundations, laying of pipes/cables/poles etc and getting out in soft/loose soilcomplete all as specified and directed.

Supply & fixing ,Laying , jointing and testing LT under ground electric power cable crossed linked polyethylene ( XLPE) insulated, galvanised steel strip or wire armoured, ISI-7098 Marked, with aluminium conductor multi stranded , heavy duty 1100 Volts grade of size 35 sqmm cross sectional area, 3.5 core ,complete all as specified and directed.

Supply and fixing in repairs wall mounted bus -bar three ph,double door 6 way , 415 Volts with 4 nos Aluminium Bus bar 200 Amp including MCCB 100 Amp ,25 KA 4 pole =01 No in sheet metal enclosere of 1.6 mm thick MS sheet with powder coat painted including connecting with existing system and cabling network including making good disturbed surfaces complete all as specified and directed.

Supply & lay, in trench GI Tubing 15 mm medium grade with all fitting complete all as specified and as directed

M&L , Gun metal globe valve 15 mm with iron wheel head heavy duty screwed both ends for iron pipe for union , ISI marked complete all as specified & directed

S&F PVC Conduit for suitable for Cable 10 Sqmm 4 core with accessories for make some AC Connection point complete all as specified and directed.

Supply & Fix exhaust fan steel body AC single phase 230 Vof size 300 mm sweep with blades and frame and louvers including making holes of suitable size complete all as specified and directed

Supply & fix starter for suitable 0.75 Hp to 3 HP motor , 415 Volts AC, 50 Hz, complete with in enclosere with powder coat painted IP-54 , including connecting with existing system and cabling network including making good disturbed surfaces complete all as specified and directed.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs. 17,118.00]

CREATIVE CONSTRUCTION (BID ID -3098030)

M/s Prakash R. Verma (BID ID -3111694)

Bidder Name

M/s Prakash R. Verma

Devika Constructions

CREATIVE CONSTRUCTION