Construction of PHC Building at Basadhar in Tehsil Theog District Shimla H.P.

Amount

Excavation in foundation, trenches, etcetra in earth work in all kinds of classification, of soils such as pick work, jumper work blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals, lift up to any height stacking excavated soil up to all leads and lifts clear from the edge of excavation and then returning the stacked soil in fifteen centimetre thick layer when required into plinths, sides of foundation etcetra consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth to the disposal point complete in all respect . including all leads and lifts as per direction of the Engineer-in-Charge

Excavation in drains and channels etc.in earth work including dressing of sideand bed and disposing of excavated earthupto a lead of 20 metres and lift upto1.50 metres disposed earth to belevelled and neatly dressed including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge

Excavation in Hilly areas in soil bymanual means excavation in soil in hilly area by mechanical means including cutting and trimming of side slopess and disposing of excavated earth with a lift upto 1.5 mtr. and a lead upto 20 mtr. As per technical specification clause 1603.1 including in all leads and lifts as per directioin of Engineer in-Charge.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and back filling in trenches with excavated suitable material including all leads and lifts as per direction of the Engineer-in-Charge. (Ordinary Soil)

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. including all leads and lifts as per direction of the Engineer-in-Charge

Providing form work with steel plates 3.15mm (Three point one five millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in including all leads and lifts as per direction of the Engineer-in-Charge in foundation ,footing bases of columns etc. and mass concrete complete in all reapsect.

Flat surface such as soffits of suspended floors, roofs, landings and the like upto any thickness complete in all respect floor etc upto 200 mm thickness

In columns, pillars, posts and struts square, rectangular, polygonal in plan complete in all respect .

In stair cases with slopping or stepped soffits, excluding landing but complete in all respect .

In beam, cantilever, girders and lintels, sides and soffits of beams beams haunching below supporting cantilevers girders bressumers and lintels of any depth in all height from floor complete in all respect.

In edges of slabs and breaks in floors and walls of any width complete in all respect .

Providing and laying cement concrete 1:6:12 mechanically mixed and vibrated ( 1cement: 6sand: 12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge

Providing and laying cement concrete 1:4:8 (One cement :four sand : eight graded/crushed stone aggregate 40mm (Forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth under floor complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying cement concrete 1:8:16 mechanically mixed and vibrated (1cement: 8sand: 16 graded stone aggregate 20mm nominal size) and curing complete on slab and floor excluding the cost of form work screed laid under flooring including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge.

Providing and laying Cement Concrete 1:1.5:3 (1 cement :1.5 Sand : 3 graded stone aggregate 20 mm nominal size ) and Curing complete excluding Cost of form work and reinforcement for reinforced Concrete work in :- in foundation footing, basis of columns and the like mass concrete upto floor all level including curing complete in all respect

in suspended floor, roofs, landing and shelves and their support balconies beams girders bressumers and cantilevers upto floor all level including curing complete in all respect.

in Columns, pillars posts and struts upto floor all level including curing complete and carriage of material within all leads, lifts and other incidental charges complete in all respect.

stair case

Providing and laying Cement Concrete 1:1.5:3 (1 cement :1.5 Sand : 3 graded stone aggregate 20 mm nominal size ) and Curing complete excluding Cost of form work and reinforcement for reinforced Concrete work in Moulding as in cornices window cill.

Providing and laying damp proof course 50mm thick with cementconcrete 1:2:4 (1 cement:2 sand:4stone aggregate 12.5mm nominal size) and curing complete. including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge

Applying a coat of hot bitumen(mexphalt 80/100 or equivalent)using 1.70 kg. per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge.

Applying cement slurry on R.C.C.slab or cement concrete work using2.75 kg. of cement per sq.metre of floor area before laying cement concrete flooring includin groughening, cleaning of the concrete surfaces complete including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge

Providing Tor steel reinforcement (SAIL,TISCO) for RCC work including bending binding and placing in position including cost of binding wire complete including all leads and lifts as per direction of the Engineer-in-Charge

Brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (one cement : six sand) second class bricks complete including all leads and lifts as per direction of the Engineer-in-Charge

Half Brick masonry in 2nd class common burnt clay building bricks in cement mortar 1: 4 ( one cement : four sand ) complete including all leads and lifts as per direction of the Engineer-in-Charge

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in Cement Mortar 1:6(1 cement:6 sand) including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth. In cement mortar 1:6 ( 1 cement : 6 sand)

Boulder filling dry hand packed tightly under floor including all leads and lifts as per direction of the Engineer-in-Charge

Providing and Laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 including all leads and lifts as per direction of the Engineer-in-Charge) 1:5:10

Back filling behind the retaining wall. including all leads and lifts as per direction of the Engineer -in -Charge.

Providing and fixing weapholes in brick masonary/stone masonry plain RCC abument, B/wall & R/wall with 100 mm dia PVC pipe( Supreme,AKG,Finolex,& Dplast) i/c all leads and lifts.as per direction of the Engineer -in -Charge.

Providing and fixing flush door shutters (Kutty flush door, Kitply industries( Swastik), SR Jindal ply wood industries), core of black board construction with frame of first class hard wood and well matched firtst class Indian teak ply veneering with vertical grains of cross band and face vaneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters.i/c all leads and lifts.as per direction of the Engineer -in -Charge. 35mm thick including black enamelled M.S. butt hinges

Providing and fixing 12mm thick 150mm wide pelmet with 25 mm diametre wooden curtain rods and brackets including fixing 25x3mm M.S. flat at 10 cm. Long and plugs etc. complete i/c all leads and lifts.as per direction of the Engineer -in -Charge. First class indian teak wood.

Providing and fixing M.S. grills of required patterns in frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws complete including all leads and lifts as per direction of the Engineer-in-Charge (i) Plain grill

Providing and fixing 6 mm everest board in ceiling of size 600 x600mm of approved shade and pattern mounted on powder coated G.I.frame work fixed /hanging with wall of ceilling etc.with specified clamp and G.I. wire and rawl plugs etc. complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.complete including carriage of materials within all leads, lifts and other incidental charges.2nd class deodar wood. 40 mm thick

Providing and fixing anodized aluminium sliding door bolts anodized colour and shade with bolts and nuts screws etc complete including carriage of materials within all leads, lifts and other incidental charges.300x16mm ( Three hundred into sixteen millimetre )

250x16mm ( Two hundred fifty into sixteen millimetre)

Providing and fixing heavy duty aluminum tower bolts (Barrel type) anodized transparent or dyed to required shade and colour with screws etcetra as approved complete including carriage of materials within all leads, lifts and other incidental charges.250x10mm (Two hundred fifty into ten millimeter)

150x10mm (One hundredfifty into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etcetera complete including carriage of materials within all leads, lifts and other incidental charges.125mm ( one hundred twenty five millimetre)

100mm ( one hundred millimetre)

Providing and fixing bright finished brass furniture handles including carriage of materials within all leads, lifts and other incidental charges.

Providing and fixing bright finished brass megnatic catcher including carriage of materials within all leads, lifts and other incidental charges.

Providing and fixing 65x35mm special quality chromium plated brass cup board lock with six leavers including necessary screws etc. complete (Indian make)including carriage of materials within all leads, lifts and other incidental charges.

Providing & fixing 19 mm thick commercial board (Novapan, Kitply, National Action tesa green) water proof shutter for up boards i/c fixing with nickel plated piano hinges with necessary screws etc complete including carriage of materials within all leads, lifts and other incidental charges.

Providing & fixing 19 mm thick (Novapan, Kitply, National Action tesa green) water proof commercial board in shelves / box for cup board with butt joints & fixing with nails & screws etc complete including carriage of materials within all leads, lifts and other incidental charges.

Providing & fixing 1mm thick Lamination ISI Marked is No12823 with butt joints & fixing with nails & screws etc complete including carriage of materials within all leads, lifts and other incidental charges..

Providing and fixing square edges cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete including carriage of materials within all leads, lifts and other incidental charges.1st class deodar wood.

Providing and fixing 6mm ply (Novapan Kitply, National) of standerd quality ISI marked and approved shade with screw nails complete including carriage of materials within all leads, lifts and other incidental charges.1st class deodar wood.

Vibro hydraulically compressed and polished terrazzo tiles (NITCO,Modern, NTC,GICO) 300X300 25 mm of NTC ISI marked No.1237 in 70% white cement & 30% gray cement the ratio of marble chips shall be 55 %white and 15% each green Yellow and mahroon .The size of Chips shall be OB and 2B laid in flooring ,on 10 mm average thickness cement plaster 1:3 (1 cement: 3 sand)jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) complete including carriage of materials within all leads, lifts and other incidental charges

Vibro hydraulically compressed and polished terrazzo tiles(NITCO,Modern, NTC,GICO) 300X300 20 mm of NTC ISI marked No.1237 in 70% white cement & 30% gray cement the ratio of marble chips shall be 55 %white and 15% each green Yellow and mahroon .The size of Chips shall be OB and 2B laid in flooring ,on 10 mm average thickness cement plaster 1:3 (1 cement: 3 sand)jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) complete including carriage of materials within all leads, lifts and other incidental charges

White glazed tiles (Kajaria,NITCO, Somany,Orient) 6mm (six millimetre) thick in skirting riser of steps and dado 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry upto all floor level complete including carriage of materials within all leads, lifts and other incidental charges.

40mm (forty millimeter) thick cement concrete flooring 1:2:4 (one cement : two sand : four graded/crushed stone aggregate 20mm (twenty millimeter) nominal size) laid in one layer finished with a floating coat of neat complete including carriage of materials within all leads, lifts and other incidental charges.

Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete including carriage of materials within all leads, lifts and other incidental charges 25 mm thick.

Kota stone slab flooring 25 mm (average) thick base of cement mortor 1:3 (1 cement :3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete including carriage of materials within all leads, lifts and other incidental charges 25 mm thick.

Providing and laying non slipery cermic tiles (Kajaria,NITCO, Somany,Orient)30x30/40x40cm of approved shade and pattren of digital series of Somany /Khajaria /Nitco or its equivalent laid in flooring treads of steps and landing on 10mm thick (average) cement mortor 1:3 (1 cement :3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying vetrified tiles (Kajaria,NITCO, Somany,Orient) of size 60x60 cm of AGL/BELL -orient Nitco Khajaria of approved shade in flooring treads of steps and landing on 12mm (Twelve milimetres) thick cement mortor 1:3 (1 cement :3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying Baroda green marble work in flooring/ on wall / Kitchen top /lab top 20mm. thick base in cement mortar 1:3(1cement:3sand) including jointing with cement mortar 1:2(1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble. 20 mm thick White makrana marble complete including all leads and lifts as per direction of the Engineer-in-Charge

Making half round nosing to Kota stone / granite stone/marble complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying red sand stone slab in treads and risers of steps on a bed of 20mm tick cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c preparing of nosing i/c rubbing and granite polish finish complete. including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying NTC heavy duty precast cement conrete inter locking paver blocks ( vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for including all leads and lifts as per direction of the Engineer-in-Charge .80mm thick block

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheet TATA or DURASHINE in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster 5 (five) microns over 5 (five) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted limpet and rubber washers complete in all respect.

Providing and fixing ridges or hips 60cm (sixty centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted steel sheet TATA, durashine in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating plus back coat of polyster of 5 (five) microns over 5 (five) microns primer coating icluding fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted GI limpet and bitumen washers complete with all accesoriees as required complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing valley 60cm (sixty centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted steel sheet TATA durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster 5 (five) microns over 5 (five) microns primer coating icluding fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted GI limpet and bitumen washers complete with all accesoriees as required complete including all leads and lifts as per direction of the Engineer-in-Charge

Prividing and fixing flushing 38cm (thirty eight centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted sheet TATA durashine in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) mircorns primer coating plus back coat of polyster of 5 (five) microsn over 5 (five) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre & prepainted GI limpet & bitumen washers complete with all accessories as required complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing 30 cm. wide 30 cm.deep 90 cm overall semicircular plain G.I. sheet gutter TATA or durashine with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design.0.63 mm thick sheet. including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing on wall face PVC (D-Plast, Finolex) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge 150mm dia pipes

Providing and fixing on wall faces PVC (D-Plast, Finolex ) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge PVC Plain bend 150mm dia

PVC shoe 150mm dia

Providing and fixing MS BP sheet (TATA or durashine) 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separately) including complete in all respect.

Steel work welded in built up sections trusses and framed work including cutting, hoisting, fixing and launching in position and applying a priming coat of red lead paint in trusses and trussed purlins in buildings complete including all leads and lifts as per direction of the Engineer-in-Charge In trusses and trussed purlins in building

in gratings framed guard bars , ladders , railing , brackets and similars works .

Providing and fixing MS BP Channel door ,window , clerestory window frame manufactured from M.S channel section of 75x40 mm including hinges jamb, look jamb, beed and welded continously with M.S.Flat 40 x12 mm and cleat for fixing MS hold fast 40x4 mm of length 20 cm in all respect including applying a coat of approved steel primer two coat after pre-treatment of the surface or as directed by in all respect Engineer-in-Charge of material within all lead and lifts

Providing and fixing window and ventilators frames manufactured of channel section 75x40 (seventy five x forty) millimeters for end frames and for center frame channel section 75x 40 mm (seventy five x forty) millimeters with mild steel flat 75x4 (seventy five x four) millimeters incombination welded together to make one frame with making square steel secation with mild steelflat of 20x4mm (twenty x four) millimeters and 12x 4 (twelve into four) millimeters , shutters of rolled steel section F- 7B (Seven B) section including glass panes of 4(four) millimeters thick in glazed panel and wire gage of designation 85 (eighty five) with0.56 (Zero point five six )millimeters dia in wire gauge panel and fixed glazing fixed with angle and T-section 25x25x3 mm (twenty five x twenty five x three)millimeters and flat of12x 4 (twelve into four) millimeters in sash bars duly welded of all comes and joints properly, hold fast of mild steel flat200x 50x 5(Two hundred x fifty x five ) millimeters duly welded at corner and joints of all steel section ,ambedded in cement concrete block 1:3:6(one cement : three sand :six graded stone aggrigate 20 mm nominal size of size 100x100x100 mm .size (one hundred x one hundred x one hundred) including providing and fixing of fitting that is handles,tower bolts hooks and eyes and applying a coat of primer with red lead paint and fixed in position completee in all respect as per architectural drawing and direction of Engineer -in charge

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm and braced with flat iron diagonals 20 mm X5 mm size with top and bottom rails of T.iron 40 mm X40 mm X6 mm with 38 mm dia steel pulley complete with bolts and nuts locking arrangements, stoppers,handles,including applying a priming coat of red lead paint including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing M.S.round holding down or anchor bolts with nuts and washer plates complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing moulded hand rail of M.S. hollow pipe 50 mm dia (D-section)welded in straight length over M.S. flat at top of vertical blusters including one coat of red oxide priming coat complete ( M.S. flat and balusters of railings shall be masured and paid separetly)including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

6mm cement plaster to ceiling in cement mortar 1:3 (1 cement : 3 sand) including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

15mm cement plaster in single coat on the rough side of brick/concrete/stone walls for interior / exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth ( in Cm 1 : 6 )including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior /exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and smooth including. Cement mortar 1:6 (1 cement : 6 sand)including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior /exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 30cm in girth and finished even and smooth including. Cement mortar 1:6 (1 cement : 6 sand)including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

20mm Cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.)including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Distempering two coats with synthetic/Acrylic washable distemper of approved brand and manufacture and of required shade on undecorated wall to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture oafter thoroughly brushing the surfaces free from mortar droppings and other foreign matter and including preparing the surfaces even and sand papered smooth.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Painting two coats (excluding priming coat ) on new steel and other metel surfaces under coat with ready mixed paint brushing to give an even shade i/c cleaning the surface all dirt, dust and other foreign matter with ready mixed paint other than whiteincluding carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Applying priming coat over new wood and wood based surfaces after and including preparing the surfaces by thoroughly cleaning oil, grease dirt and other foreign matter sand papering and knotting with ready mixed paint brushing wood primer pink as per HP.PWD specification, including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts, including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters with enamel paint other than white as per HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts, including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Painting two coats with stain enamel paint of approved design or its equivalent on undecorated wall surfaces to give an even shade including cleaning the surface of all dirt, dust and other foreign matters and sand papering as required with paint complete. including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Polishing two coats with french polish on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood fille including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials within all leads, lifts and other incidental charges.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand i/c preparation of ground.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing plinth protection 50mm thick in cement conc. 1:3:6 (1cement :3 sand:6 graaded stone aggregate 20mm nominal size)including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Constructing Course rubble hammer dressed 'U' shape opensurface drain with side wall. 15x22 cm in cement mortar 1:6(1 Cement : 6 Sand) and inside plastring with cement plaster1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing MS 100mm dia pipe embedded in cement conc.block (30X30X30)1:2:4 complete as per Arch Drg..including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing M.S. Bracket 40x40 Cm. of 50x50 mm M.S. hollow section frame work with 20x20 mm hollow M.S. section and 12 mm solid square bars in combination as per Arch. Drg. Complete.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing & fixing to wall ceiling and floor galvanised mild steel tubes ( medium grade) tube fitting and clamps including making good the wall , ceiling floor complete including all leads and lifts as per direction of the Engineer-in-Charge 25 mm nominal bore

15 mm nominal bore

Providing & laying in trenches galvanised mild steel tubes ( heavy grade) tube fitting ( earth work in trenches to be measured and paid separately complete. including all leads and lifts as per direction of the Engineer-in-Charge.20 mm nominal bore

Making connection to galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and treading the pipe complete. including all leads and lifts as per direction of the Engineer-in-Charge

Fixing water meter stop-cock in GMS tube i/c necessary fittings such as mild steel galvanished jam nut .sockets etc. complete cutting and making long screws (water metre and stop cock to measured and paid for separately) 25mm nominal bore including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Constructing water collection chamber 300x300x650mm (three hundred into (three hundred into six hundred fifty millimetre) in side size for collection of water with cement concrete slab 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimeetre) nominal size) 75mm (seventy five millimetre) thick foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm (forty millimetre) nominal size) finished with floating coat of neat cement and 100mm (one hundred millimetre) cast insitu plain concrete wall in 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre nominal size) including form work complete in all respect including carriage of materials within all leads and lifts. with 100 mm thick walls of bricks masonry in cement mortar 1:5 ( 1cement:5 sand)

Providing and fixing polythelene aluminium polythene (PE-AL-PE) composite pressure pipe U.V. stablized with carbon conforming to IS: 15450-2004 for water supply including clamps at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall including carriage of materials within all leads and lifts complete in all respect. 1216 ( one thosuand two hundred sixteen) 16mm ( sixteen milimetre) O.D. pipe

Providing and fixing composite and seal compression fittings as per IS 15450-2004 for cold water supply for example tees, elbows, reducers, connectors, couplers and clamps with jointing, testing and fixing complete including cuting and making good the wall etc including carriage of materials within all leads and lifts complete in all respect. Equal tee

Reducing tee 1620

Female branch tee 1216x1216 x 15 mm thread

Female elbows tee 1216 x 15 mm thread

Male thread connector 1216 x 15 mm thread

Female elbows tee 1216 x 15 mm thread

couplers 1216

Reducer 1620x1216.

Providing and fixing PVC water storage tank ISI : 12701 marked , G.I inlet and outlet connection , 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting uo to all heights above ground level Complete. ncluding carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive , cost of cutting and making good the wall and floors etc. complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge 110mm x 90 mm

110mm x 75mm

Providing and fixing high pressure PVC spigot and socket , waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete. including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge 110mm dia

75 mm dia

Providing and fixing sand cast/cast iron holders bats including steel bolts to sand cast iron/cast (spun) iron pipes embeded in and including cement concrete blocks 100mm X 100 mm X 100 mm of 1:2:4 mixincluding cost of cutting holder and making good the wall 75mm dia / size pipe including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

100 mm nominal diametre

Providing and fixing PVC single equal branch with oval access door , ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive complete 110 mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

150mm dia

Providing and fixing PVC door band with oval access door , insertion rubber washer 3mm thick bolts and nutsISI marked complete including fixing with approved adhesive complete 110 mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

75 mm dia

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive complete 110 mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

75mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive complete 110 mm dia including carriage of materials within all leads an lifts as per direction of Engieer in charge

75mm dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive complete 1101mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

75mm dia

Providing and fixing PVC offset 45 degree ISI marked including fixing with approved adhesive complete 110 mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

150mm dia

Providing and fixing PVC double equal branch with oval access door , ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive complete 110mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

75mm dia

Providing and fixing PVC plain double equal branch ISI marked complete including fixing with approved adhesive complete 110mm dia including carriage of materials within all leads an lifts :-

75mm dia

Providing and fixing PVC cowl 110 mm nominal diametre including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

75mm dia

Providing and fixing Vitrous china wash down water closet squatting pan Indian Type W.C. Pan) including jointing the trap with soil pipe in cement mortar 1;1 (1 cement 1 Sand)Orissa pattern :- No.2071 size 580x440 mm of CERA / :HINDWARE in white shade.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately)Angle Indian Universal closet including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing PTMT coloured /white high density polyethylene/ poly propylene 10.00 liters capacity (full flush) European standard control low level flushing cistern.with a pair of C.I. BRACKETS ,With fittings such as lead valve syphon, 15mm nomilal size PVC ball valve with polythene flot ,with push botten, coupling for connection with complete with inlet, outlet and overflow pipes ,40 mm dia C.P. flush bend etc. complete.No. 2603 of CERA/ HINDWARE including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and macking good the same but excluding fittings FLAT BACK category No 1025 No 1025 size 550x400 mm including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge Orissa pattern:- 20004 size 58x40 cm.

Providing and fixing vitreous china pedestal for wash basin complete recessed at the back for the reception of pipes and fittings.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing PVC. 110mm size 'P' or 'S' trap for water closet (squatting pan) including jointing the trap with the pan and and PVC pipe with approved adhesive etc. complete. 110 mm dia.including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing C.P. Brass chain 50cm. Long and rubber plug of following sizes for sink or wash basin 32mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing M.I. Union for wash basin or sink -32mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing C. P. Brass S Trap for wash basin and sink 32mmdia. including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing C. P. Bottle waste wash basinor sink as per the direction of Engineer-in-charge

Providing and fixing C.P. brass waste for wash basin or sink 32 mm dia iincluding carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing & fixing 32 mm dia, PVC waste pipe for wash basin or sink including check nut including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing & fixing 100 mm dia, C.P. grating including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washer iincluding carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing C.P. brass towel rail complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws600 X 20 mm including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing 600x120mm (six hundred into one hundred twenty millimetre) glass self with CP brass brackets and guard rail complete fixed to wooden plugs with CP brass screws complete in all respect .

Providing and fixing C.P. brass towel paper including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing choromium plated brass soap dish with CP brass brackets fixed to wooden cleats with CP brass screws complete in all respect including carriage of materials within all leads and lifts.

Providing and fixing prayag double bowl kitchen sink or M.S brackets painted white i/c cutting holes in walls and making good the same but excluding fitting ISI marked No.6321.460x560x229including carriage of materials within all leads and lifts.

Providing and fixing C.P Brass bib tap with Capstan head .15 mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing CP brass pillar tap with capstan head 15 mm dia including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing c.p. brass angle valve 15mm without Nuts and pipe. including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing PTMTpush cock of approved quality .20 mm female thread including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing & fixing C.P. stop cock 15mm dia i/c all lead and lift and as per the direction of Engineer in charge

Providing & fixing PVC connection with brass union I ) 300mm/450 mm in length & 15mm nominal i/c all lead and lift and as per the direction of Engineer in charge

Providing and fixing brass full way valve with wheel 15mm nominal bore including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing brass full way valve with wheel 25mm nominal bore including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge:

Providing & fixing Mixer for kitchen sink with top/ bottom swingein spout 15mm dia.i/c all lead and lift and as per the direction of Engineer in charge

Providing & fixing water pump to lift rain water i/c all lead and lift and as per the direction of Engineer in charge

Constructing manhole with R.C.C. top slab in 1:2:4 mix ( One cement : two sand : four graded stone aggregate 20mm nominal size ) foundation concrete 1:4:8 ( one cement : four sand :eight graded stone aggregate 40mm nominal size ) inside plastering 15mm thick with cement mortar 1:3 ( one cement : three sand )finished with a floating coat of neat cement & making channels in concrete 1:2:4 mix ( One cement : two sand:four graded stone aggregate 20mm nominal size ) finished smooth complete including curing & testing inside size 800x800x500mm deep including Precast RCC cover with frame (heavy duty single seal pattern ) 455mm x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (Weight of cover 23Kg and weight of frame 15 Kg ) with 230mm thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 ( one cement : three sand ) i/c all lead and lift and as per the direction of Engineer in charge

Providing and fixing reinforced cement concrete 300X300 mm with frame for gully trap the weight of cover to be not less than 4.53 kg including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing reinforced cement concrete 300X300 mm with frame for gully trap the weight of cover to be not less than 4.53 kg including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing precast RCC cover with frame for 600x450 including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing C.P Grab bar 40 mm sheet pipe at 78 cm Ht.with M.S .Plate as per detail as the position of seat and wash basin complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Supplying and filling broken crushed stone agg.chipping agg. 40 mm nominal size complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Supplying and filling sand for dispertion complete including carriage of Material with in all leads and lifts as per the direction of Engineer-in-charge

Providing and fixing ISI marked high pressure PVC spigot and socket, waste and ventilating pipes including fixing with approved adhesive etc. complete.including carriage of material with in all leads and lifts.and as per the direction of Engineer in-charge. . (a) 75 mm.dia.

110 mm dia

P/F P.V.C. Cowl ISI marked with approved adhesive etc. complete.75mm dia i/c all lead and lift and as per the direction of Engineer in charge

Providing & fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete150 mm dia i/c all lead and lift and as per the direction of Engineer in charge

Providing & fixing PVC clumps ISI marked including fixing with approved adhesive etc. complete150 mm dia i/c all lead and lift and as per the direction of Engineer in charge

Vinod Chauhan