CWE/P-46/2019-20 SPECIAL REPAIR TO JCOS/ORS MD BLOCK NO P-33 (09 QTRS ) AT UNCHI BASSI UNDER GE (SOUTH) PATHANKOT

Amount

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each including taking out hold fast complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each including taking out hold fast complete all as specified and directed.

M&L factory made Glazed and skelton shutters 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (with shash bars any numbers), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated all as specified.

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after tarring of hollow portion of frame complete all as specified and directed

M&L 1.25mm thick pressed steel frames with one shop coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges (ISI marked), lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after taaring of hollow portion of frame complete all as specified and directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixed complete alll as specified .

S&F factory made Solid Panel prelam PVC door shutters 30 mm thick (style) consisting of frame made out of MS tubes of 19 guage thickness and size of 40mmx20mm for stiles as well as top, lock and bottom rails. MS frame shall have a coat of metal primer of approved make. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel made of 5mm thick PVC sheet of density 600kg/cum manufactured by an ISO-9001-2008 certified company, of thickness 110mm width forming stiles in which 100mm should be flat and 5mm should be taper and 5mm thick, 135mmwide PVC sheet for top rail and bottom rail in which 125mm should be flat and 5mm should be tapper on either side of panel. also for the lock rail 145mm sheet , 125mmshould be flat and 5mm tapper on either side. an additional 5mm thick PVC strip of 20mm width is to be stuck on inner side of C chanel using PVC solvent cement adhesive. Panelling of 10mm Prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beadings on either side and additional 30mm wide PVC beading as gap insert bellow top and bottom rails complete all as specified and directed.

M&L Steel windows of Z section with side hung shutter including projecting type hinges with steel handles, 2 Nos steel tower bolts 100 mm long peg stay complete with glazing bars, dovetailed or welded including locking arrangements and one shop coat of zinc primer complete all as specified and directed by Engr-in-Charge.

All as per Srl item No 09 here-in-before but without glazing bars

M&L Steel windows or ventilators fixed type, with glazing bars including one shop coat of zinc primer complete all as specified and directed by Engr-in-Charge.

M&L Steel ventilators with top hung shutter including hinges, steel peg stay complete including one shop coat of zinc primer complete all as specified and directed by Engr-in-Charge.

M & L framed work such as grills, grating etc with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barrel, iron doors, ladders, balusters, walkway, frame work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified.

M & L galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified.

M & L 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

M & L 3 mm thick figured glass, pin head type and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

S & F mild steel sliding door bolts, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate, 300mm long, ISI marked all as specified.

Supply and fxing Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

M & L Aluminium alloy handles (ISI marked), cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, two legged, overall length of cover plate 50 mm complete all as specified and directed.

M & L Mild steel butt hinges, medium weight, cold rolled (ISI marked),100mm long , complete all as specified.

M & L for 25mm thick flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both sides, including fixing Ist class softwood beading of size 20x20mm over all sides and fixed with screws to frame all as ppecified and directed.

S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30mm complete all as specified and directed

S & F hasp and staple,100 mm long aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified. ISI Marked

S & F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified

Supply and fxing in repairs, 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate fixedto pressed steel frame/ MS frame/ wooden chowkhats including necessary fixing arrangement and welding work as required complete all as specified.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic coloured tiles in skirting/dado 350 x 450 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match required shade over and including 10 mm thick cement plaster in cement mortar 1:4 as in backing coat rough finished surface complete all as specified.

M&L for edge cut joint free glazed/matt finish coloured or printed ceramic tiles 8 to 9 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M & L machine pressed chequered cement concrete tiles 300x300x 22 to 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment including 20mm thick screed bed in cement moratr 1:6 complete all as specified and directed.

M & L Plain Cement Concrete 1:4:8, type D-2 (using 40mm crushed stone aggregate), 100mm thick as in sub base complete all as specified.

M & L 50mm thick plain Cement Concrete 1:3:6, type C-1 (using 20mm crushed stone aggregate), as in plinth protection, flooring etc laid in alternate bays finishing even and smooth without using extra cement complete all as specified.

Dismantling of brick tile or terracing tiles, single layer on roof upto any height and removing all unserviceable materials outside the Cantt area complete all as specified.

M&L roughening surfaces of old concrete surfaces by picking sweeping, cleaning and washing down with water to remove dust etc including taking down existing roof treatment and brushing neat cement slurry @ 3 Kg/Sqm all as specified and directed

M&L screed bed or bedding layer 10mm thick in cement mortar 1:3 mixed with water proofing compound on concrete surfaces in roof, complete all as specified and as directed. Note : WPC shall be measured and paid separetely

M & L for providing and laying of water proofing treatment of roof APP (Atactic Polyproplylene) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane all as specified and directed. Note: The work shall be executed through authorised applicator by the manufacurer of membrane as specifeid in particular specificaction.

M & L cement concrete tiles 300x300x 22 to 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment as in roof complete all as specified and directed.

M & L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof padding with liquid WPC laid to slopes as directed and approx thickness 75mm, and finishing the surfaces even & smooth without using extra cement, complete all as specified and directed. Note : WPC shall be measured and paid separetely

M & L PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate), fas in copings, benching , kerb or mud stops,rounded or chamfered angles and edges, including necessary form work complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically described (reinforement cut as required to facilitate demolition), complete all as directed by Engineer-in-Charge.

M & L precast cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregates) as in cover slab,cover etc including necessary moulds/ form work for septic tank/soakage well/manhole cover and set in cement mortar 1:6, complete all as specified and directed.

M & L TMT bars 6mm to 8mm dia. as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L TMT bars 10mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and Labour for brushing & cleaning surface of sunken floors & surface painting with layer of blown bitumen of any penetration and applied hot @ 1.7kg/Sqm complete all as specified and directed.

M & L plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified.

M & L 50mm average thickness plain cement concrete 1:2:4 type B-1 (20mm graded crushed stone aggregate) as in sunken floor finished even and fair using water proofing compound complete all as specified and directed. Note : WPC shall be measured and paid separetely

M & L 25mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) finished even and fair, complete all as specified.

M&L 15mm thick rendering in cement mortar 1:3 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement and with water proofing compound as in sunken floor or external plaster , complete all as specified

Supply only liquid water proofing compound complete all as specified

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, complete all as specified and directed.

All as per item No.53.00 here-in-before, but except bricks.

M & L brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including necessary form work complete all as specified.

M & L plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Taking down old broken cast iron pipes from existing sewage line or along plumbing stack along the walls including necessary excavation in trenches where required, removal of surplus soil and returning filling in complete, supplying, laying in trenches or along the walls with MS clamps of standard specifications and including S & F of new 100mm dia cast iron (sand cast) pipe complete all as specified and directed by the Engineer-in-Charge

All as per item No.59.00 here-in-before, but 75 mm dia

All as per item No.59.00 here-in-before, but 50 mm dia

S & F 50 mm dia cast iron cowl ISI marked complete all as specified and directed.

M&L PVC (SWR) pipes 110mm dia ISI marked any length single socketed with rubber ring joint fixed to walls as drainage pipe complete all as specified and directed.

M&L PVC (SWR) bends any radius of 110mm dia ISI marked complete all as specified and directed.

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 10mm thick rendering in cement mortar 1:3 on fair faces of brick or concrete surfaces as in ceiling & finishing the surface even and smooth without using extra cement including applying three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, including applying two coats cement base paint of approved brand including preparation of newly plastered surfaces of wall complete all as specified

M&L 15mm thick rendering in cement mortar 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, including applying two coats of oil bound distemper including preparation of newly plastered surfaces of wall complete all as specified

M&L 15mm thick rendering in cement mortar 1:6 on fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, including applying three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

M&L Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item No 72 here-in-before but except pipe.

M&L Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

All as per Srl item No 74 here-in-before but except pipe.

S&F Chromium plated brass shower rose with or without swivel joints, 125 mm size including fixing to steel pipe or union, all as specified.

Supply and fixing bib taps 15mm bore of cast copper alloy chromium plated (ISI marked) fancy type, screwed down, high presure, screwed both ends for iron pipe or for brass ferrule, complete all as specified and directed.

Supply and fixing in repairs stop valve/angle valve of cast copper alloy chromium plated (ISI marked), fancy type screwed down high pressure, screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

S&F tubular towel rail, 20mm dia, D type, 60cm long between flanges Brass chromium plated, fixed with rawl plugs all as specified and directed

M&L Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

S & F PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

Supply and fxing in repairs, PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints , complete all as specified.

Supply and fxing in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc, and including concrete bedding complete, all as specified and as directed.

S&F cast iron trap 'P' or 'S' 100 mm all as specified and directed.

Dismantling water tanks and removing from site capacity exceeding 250 ltr and not exceeding 500 ltr complete all as specified and directed.

Supply and fxing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug complete all as specified and directed.

M&L for three coats of white wash including preparation of old treated surfaces of ceiling by complete removal of existing treatment complete all as specified.

S & F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe fixed complete all as specified.

Preparation new wooden surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

Preparation new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

Preparation of old plastered/ un-plastered wall surfaces or wood based surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of dry distemper on walls including cornices, pilasters etc, complete all as specified.

M& L for preparation of old treated surfaces of walls and applying one coat cement base paint of approved brand to match the shade as per colour scheme/pattern all as specified and as directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L Point wiring for light/fan/bell point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

All as per above item no 94.00 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

All as per above item no 94.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 94.00 here in before but for one light controlled by two way switch all as specified and directed.

All as per above item no 94.00 here in before but for one bell/buzzer point controlled by one bell push button on same board with other switch or independentwith cable 1.5 Sqmm size all as specified and directed.

M&L Point wiring for 15 Amp socket point controlled by one switch with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L Point wiring for 15 Amp socket point controlled by one switch with 4 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 4sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L Switch piano flush type 5 Amp single pole one way, (ISI marked), complete all as specified.

M&L bell push 5 amp, 240 volt, flush type (ISI marked) , complete all as specifed.

M&L socket outlet 2 in 1, 3 pin, 5 Amp flush type ,complete all as specifed.

M&L Switch socket combination 2 in 1, 3 pin, 5 Amp flush type,complete all as specifed.

M&L Switch socket combination 2 in 1, 3 pin, 5 & 15 Amp flush type,complete all as specifed.

M&L Ceiling rose, 3 phase/bakelite 65x50mm two or three therminals isolated body fixed on PVC round block complete all as specified.

M&L buzzer ding dong AC 230 volts all as specified and directed by Engineer-in-Charge.

M&L Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

M&L Stepped type electronic fan regulator 0 to 4/5 step , flush type, heavy duty with hum free snubber circuit complete all as specified.

S&F LED Lamp 230 volts,50 Hz,inverter LED 9 watt ,lumen 900 lm, rated current 0.045A, CRI less than 80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back time 04 Hours, complete all as specififed and direccted.

S&F LED bulk head light fitting 1x18/20 W suitable conf including electrically to ceiling rose usning cord flexible 3 core PVC insulated overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as directed by Engr-in-chagre

S&F LED Lamp 230 volts,50 Hz,inverter LED 18/20 watt ,lumen 900 lm, rated current 0.045A, CRI less than 80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back time 04 Hours, complete all as specififed and direccted.

Supply and Fix decorative box type fitting 4 feet long with blue coloured end caps for LED tube 1x20W LED including LED tube 4 feet long of 20W having bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed

Supply and Fix corner street light fittings 24 watt LED new generation energy saving and environmental friendly long life versatile pressure die cast aluminium with mid power LEDs as light source and exclusively designed polycabonate cover alongwith electronic driver complete all connecting electrically using cord flexible 3 core copper flexible cable of size 23/ .0076 including galvanised iron bracket 1.2 mtr long of 25 mm dia incl suitable clamps with nut, bolt and washer and fixing the light to the building all as required at site or directed

Supply and Fix in replacement existing UNSV tube light fitting with LED 1 x 20W inverter batten type fitting 4 feet long aluminium extruded housing, charging time 10-12 hours and back up time 04 hours, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed. Notes for Srl item no 110 to 115: (i) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (ii) LM 80 report from LED manufacturer (iii) Test certificates to be submitted before commencement of work/ claiming for payment . (iv) Warranty certificate for minimum 2 years to be submitted from OEM.

Disconnecting and taking down ceiling fan 1400mm sweep / exhaust fan upto 450mm sweep for servicing, strip opening of fan including cleaning, greasing and servicing complete at site and reassembling and refixing in existing/new location after replacing rubber reel, fixing bolts and nuts with lock pins, connectors for complete fan including writing MES No. all as required and directed by Engr-in-charge and connecting up with new flexible twin core copper conductor cable, testing complete after servicing and fixing for smooth and noise free operation all as specified and directed.

Supply & Fix Exhaust fan AC sinlge phase 230/240 volts of size 300 mm sweep steel body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

S & F in replacement existing unsv distribution board iron clad, with double door 4 way with IP-54,1K-09 protection,cemet spill prptector suitable for MCCB as incommer AC 415 Volts three pole with thermal release adjustable type (80% to 100 % ) and MCB as outgoing ,complete with appropriate size copper bus bar and neutral link complete with including one MCCB 3 pole 415 Volts 125 Amps rating with rupturing cap 25 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately).

M&L MCB SP 5 to 32 Amp, 240V with 10KA breaking capacity of 'C' series 10 KA all as specified and directed.

M&L MCB SP 40 Amp, 240V with 10KA breaking capacity of 'C' series 10 KA all as specified and directed.

S&F MCB single pole & neutral upto 40 Amps, 240 Volts 'C' series, 10 KA, complete all as specified.

S&F in replacement sheet metal enclosure factory made (Double door) type IP-43 Protection. Isolated Neutral,Door earthing, cement spill protector, IK-08 complete, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame, necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

M&L Switch piano flush type 5 Amp single pole two way, (ISI marked), complete all as specified.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of GI pipe/LT/HT cables in any type of soil and getting out, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric underground cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm 3.5 core complete all as specified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

M&L for LT indoor /out door, heat shrinkable type cable end termination suitable for aluminium conductor cable of size 25 sqmm 3.5 core core with working voltage 1100 volts complete all as specified and directed.

M & L GI pipe light grade 40 mm bore with all fittings for cable protection fixed to walls/ poles or laid in trenches, under road/ under culvert/ under path/ under floor /on wall etc with fixing clamps, nuts bolts etc all as specified.

M & L Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be measured and paid.

M & L Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Cutting and existing steel tubing for alteration or addition including screwing existing steel tubing to form connection/branch pipe etc for 50mm bore pipes complete all as specified and directed.

S & F 50mm bore gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe fixed complete all as specified.

M&L Steel water tubing of 50 mm bore ‘medium grade’ galvanized with all fittings laid in trenches, complete all as specified.

M&L Steel water tubing of 25 mm bore ‘medium grade’ galvanized with all fittings laid in trenches, complete all as specified.

M&L for Construction of valve pit of size 70 cm x 70 cm x 70 cm (internal dimentions), brick construction, including all necessary excavation and earth work in any type of soil, returning, filling in, disposal of surplus spoil to a distance not exceeding 50m and depositing where directed, PCC in foundation of the mix (1:3:6), type C-2, (using 40mm graded crushed stone aggregate) brick masonry in cement mortar (1:4) rendering, 10 mm thick cement mortar (1:4), internally, finished even and fair pointing flush externaly as the work proceeds in the same mortar, mild steel frame, MS sheet cover 3.15mm thick with handle and locking arrangement, painting all the exposed MS work with two coats of synthetic enamel paint of the tint as approved by the GE over a coat of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paint complete all as specified.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

SATISH AND CO

INDERJIT SINGH

S S CONSTRUCTION

M/S J N TRADERS

AGGARWAL ASSOCIATES

KULBHUSHAN AGGARWAL

M/S ONKAR SINGH PATHANIA

JAI DURGA CONSTRUCTION CO