PERIODICAL SERVICES TO CERTAIN OTM ACCN AT SI LINES UNDER GE BHOPAL

Amount

Note : 1. Contractor will deposit the requisite quantity of Distemper, Exterior weather coat paint, and other materials with Original Purchase Voucher, Manufacturers Test Certificate (As directed by Engr-in-Charge) required for the work within fifteen days from the date of commencement of the work. The paint will be issued to the contractor as and when required for carrying out the work at site which will be signed by contractor or his rep and Engr-in-Charge. 2. Mixing of oil bound distemper, exterior/interior emulsion paints etc shall be carried out with mechanical mixer/stirers. 3. Surface shall be allowed to dry completely before application of any paint. Wet or newly plastered surfaces with visible moisture shall not be painted till it is dry. 4. The rate quoted against BOQ are including necessary scafolding expences upto triple storey buildings.

M&L for preparation of old decorated surfaces of wall by brooming down; scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots and stopping nails marks with cement putty and applying one coat of white wash on walls complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceilings by brooming down; scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots and stopping nails marks with cement putty and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for complete removal of old decorated surface of wall and applying two coats of oil emulsion distemper white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by brooming down; scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots and stopping nails marks with cement putty and applyng one coat of oil emulsion distemper complet all as specified and directed.

M&L for preparation of old decorated surface of walls by brooming down; scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots and stopping nails marks with cement putty and applying one coat of cement based paint complete all as specified and directed.

M&L for preparation of old painted wood/wood based surfaces, exc 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint as directed and specified.

M&L for preparation of old painted iron/steel surfaces, exc 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint as directed and specified.

M&L for complete removal of old decorated surface of walls and applying two coats of exterior weather proof water base emulsion paint, white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of old decorated surface of walls and applying one coat of exterior weather proof water base emulsion paint, white/tinted complete all as specified and directed.

M&L for complete removal of old decorated surface of walls and applying two coats of interior plastic emulsion paint, white/tinted over and including 1mm thick coat of white cement based putty complete all as specified and directed.

M&L for preparation of old decorated surface of walls and applying one coat of interior plastic imulsion paint, white/tinted complete all as specified and directed.

M&L for preparation of old decorated surface of ceiling and applying one coat of interior plastic imulsion paint, white/tinted complete all as specified and directed.

M&L for high class french polishing on surfaces of any description, width or girth including cleaning and preparing the surface and applyiing a coat of wood filler as required to achieve glossy finish complete all as specified and directed.

M&L for 1mm thick coat of white cement putty on walls/ceiling, finished even and smooth complete all as specified and directed.

M&L for ShaliCryl ® 215 single component, UV resistant, unique elastomeric, high build exterior water proofing coating based on a revolutionary acrylic polymer with quick-set capabilities to resist moisture attack with and including comprising of following stages:- (a) Surface Preparation:- Removing all loose and foreign materials, if any by washing with a jet of air / water. • Repair structural defects before application of ShaliCryl ® 215. • Filling voids and undulation area with polymer mortar made out of Shali SBR latex, water, cement and sand in the ratio of 1:1:5:12.5. • Filling cracks up to 3 mm with Plasti Seal and cracks over 3 mm with Plasti Seal P after opening the crack to 'V' cut. • Damaged poor plaster surface in old building shall be removed and re-done with new cement & sand in the ratio of 1 : 4 admixed with ShaliPlast LW+ @ 200 ml / bag of cement. (b) Primer Application:- Applying ShaliPrime WB as Primer after dilution with potable water in the ratio 1:0.5 for a theoretical Coverage 8-10 sqm/ Lit of the mix and allow it to dry for 3-4 hrs. post elimination of undulation, roughness of concrete, joint marks, voids and any other surface correction. (c) Application of Material:- Applying first coat of ShaliCryl ® 215 over the primed surface @ 160 ml / sqm. Add maximum of 10% potable water by volume for the first coat only, if required, to have brushable consistency only. • Allow the applied coating to dry 6-8 hrs of application. • Applying second coat of ShaliCryl ® 215 without dilution over dried first coat @ 140 ml / sqm and allow it to dry and let it dry for 72 hrs. • Applying a coat of 100 micron of ShaliCryl TC 100. (d) Make: Specifications here in before are considered from STP make but the contractor can provide similar materials of any other make as specified in approved list of makes.

Taking down plants/vegetable growth (upto 10cm girth) from buildings walls, parapets by cutting/ chiseling fully without disturbing structure upto height of 10.00 m from ground level at different locations and cleaning the surfaces neatly with wire brush to remove dust and other foreign particles and applying hydorochloric acid (HCL) on left over root portion and making good the disturbed surfaces in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster of any description on brick/stone walls, concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M/L rendering 15 mm thick cement mortar on brick/stone surfaces or surfaces other than fair faces of brick work in cement mortar 1:6, even and smooth finish without using extra cement, in patches complete all as specified and directed

M&L for rendering 5 mm thick in cement mortar 1:3 on brick/ concrete surfaces of ceilings, finished even and smooth wthout using extra cement complete all as specified and directed.

M&L for rendering 15mm thick rendering in cement mortar 1:4 on brick/concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil emulsion distemper, white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of exterior weather proof water base emulsion paint, white/tinted over and including 1mm thick coat of white cement based putty, finished even and smooth complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

S&F of chicken wire mesh, mild steel of 12mm mesh size and 0.56mm dia of wire and fixed with nails complete all as specified and directed.

M&L for crack filling with approved crack filling compound of approved make, crack thickness more than 3 mm; including opening of cracks, cleaning, and necessary scaffolding suitable for height upto 10.00 mtr from ground level complete all as specified and directed.

Hacking out old broken glass (any thickness, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beadscomplete all as specified and directed.

S&F of 3mm thick plain sheet glass, ordinary quality and glazing with oil putty in area n exc 0.50 Sqm each pane complete all as specified and directed.

S&F of 4.8mm thick plain sheet glass, ordinary quality and glazing with oil putty in area n exc 0.50 Sqm each pane complete all as specified and directed.

S&F in repairs stainless steel wire cloth with 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed to frames with screws complete all as specified and directed.

JYOTI ENTERPRISES (BID ID -3063928)

M/s H V Infra Projects (BID ID -3061265)

M/S VAIBHAV ENTERPRISES (BID ID -3059919)

Neelam Traders (BID ID -3072481)

sachinder singh (BID ID -3063392)