ADDN/ALTN TO UNIT DESK ROOM AND PROVISONING OF STORE ROOM 4 AFLU AND SPECIAL REPAIRS TO ROOF BUILDING NO P-37 AT HQTC BANGALORE.

Amount

Demolition Stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc all as specified and directed. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified.. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

M&L for Vitrified Ceramic tiles light shade 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 all as specified.

All as per item No 04 but as in skirting over and including 8 to 10mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified.

M&L for joint free non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 all as specified..

M&L for joint free non - skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of CM 1:6 all as specified.

All as per item No 07 but as in skirting over and including 10mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified.

M&L for glazed ceramic coloured/ digital wall tiles in vertical surface 350x450x7mm/ 450x300x7mm/ 450x350x7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering on brick work or concrete surfaced wall as backing coat of cement mortar 1:4 all as specified and directed.

M&L PCC under flooring using 1:3:6 type C2 (40mm graded aggregate) all as specified and directed.

M&L for 20mm thick Granite of any type work (table rubbed and polished) in cooking plateform, widow sill and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade granite incl 15mm thick screed bed in CM 1:6 all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed.

S&F in repairs for Prelaminated particle board, 18/19mm thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work and including pvc beading to be fixed at faces of board all as specified and directed.

M&L 2nd class hard wood Plain fillets. square, rectangular or triangular, exc 13Sqcm & n. exc 25sqcm in section, clean sawn, secured with screws all as specified and directed.

S&F in repairs 40mm width of flap (when open) continuous (piano) hinges, mild steel, bright finish or electrogalvanised all as specified and directed

S&F in repair ball catcher with 8 mm dia steel ball and brass body and striking plate including letting in and fixed complete all as specified

S & F in repairs stainless steel self closing auto hinges for cabinet shutter complete all as directed

S & F in repairs stainless steel telescopic channel ball bearing drawer channel 500 MM with loading capacity: 45Kgs complete all as directed

S&F 125mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified and directed

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified and directed

S&F in repairs kitchen utensil rack in steel made of premium grade stainless steel and highly durable and rust-proof of size not less than 90cmx80cmx20cm complete all as specified

Supply and fixing in repair of sink mixer raised J shaped swinging spout wall mounted model with connecting legs and wall flanges of make Make-Jaguar Cat No-CQT- CON 319KN or equivalent all as specified and directed.

S&F in repairs 15mm Bib cock with wall flange chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule and fixed of make Jaguar Cat No FUS 29037 or equivalent all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each all as specified and directed

S&F solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) all as specified and directed

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet 12mm thick to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed.

S&F 100mm long Butt hinges, medium weight, cold rolled mild steel all as specified and directed,

S&F for 125mm aluminium anodised barrel tower bolts of extruded section and fixed all as specified and directed.

S&F 125mm Aluminium handles, cast type anodised all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for stair handrail, balcony hand rail all as specified and directed.

Dismantling aluminium work including doors, gates, partition frame or shutter etc all as specified and directed.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S & F framed work as grills conforming to Fe 290 Gde E-165 all as specified and directed.

S&F Anodised aluminium door, window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

S&F sheet glass, of 4mm thick ordinary quality with beading in exc 0.5sqm square in each pane all as specified and directed.

S&F sheet glass, of 4mm thick ordinary quality ground or obscured or frosted, on one side in square in each pane all as specified and directed..

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dresses stonework and precast concrete articles. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

M&L for Pre-cast cement concrete block type C1 1:3:6 (20mm graded stone aggregate) masonry with solid blocks, exc. 10cm in width and setting in mortar 1:6 complete.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. Including racking out joints, hacking for key, scrubbing down with water, etc. all as specified. Note: All debris and rubbish shall be removed from MOD land during or at the end of each working period at his risk and cost in accordance with all applicable federal, state, and local regulations.

M&L for rendering 15mm thick cement plaster in cement morter 1:4 with and including water proofing compound @ 2% by wt. of cement, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement all as specified and directed.

M&L for 2 coats of cement base paint over a coat of priming plastered and other surfaced with alkali resistant priming paint including preparation of new surfaces all as specified.

M&L for Complete removal of existing surface finish and applying 2 coats of cement base paint over a coat of priming plastered and other surfaced with alkali resistant priming paint including preparation of old surfaces all as specified.

M&L for Rendering 15mm thick on fair faces of brick works or concrete surfaces in CM 1:6 and finished even and smooth without using extra cement all as specified.

M&L for Preparing the new surfaces of wall and applying two coat of oil bond distemper over a coat of 1-3 mm Birla care wall putty all as specified and as directed

M&L for Complete removal of existing surface finish and applying 1-3 mm Birla care wall putty and two coat of OBD over one coat of primer all as specified and directed

M&L for Complete removal of existing surface finish and applying wall care putty and three coat of white wash ceiling all as specified and directed.

Rendering 5mm thick cement plaster in cement morter 1:3, on concrete sufaces as in ceiling, finished even and smooth without using extra cement all as specified and directed.

M&L for preparing new plastered on ceiling and applying three coats of white wash all as specified and directed..

M&L preparation of old surface and applying two coat of White wash on old ceiling surface all as specified and directed.

M/L Preparing old painted wooden surface and applying one coat of Synthetic enamel Painting to wooden surface all as specified and directed.

M/L Preparing old painted steel surface and applying one coat of Synthetic enamel Painting to steel surface all as specified and directed.

M&L for preparing new wood surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparing new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F tubes 15mm bore, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down old polyethelene tubing all as specified and directed..

All as item no 55 above but 20mm bore all as specified and directed.

All as item no 55 above but 25mm bore all as specified and directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in ement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as specified and directed.

Dismantling water tanks, capacity in litres exc 500 & n exc 1000 and removing to store all as specified and directed..

S&F rotational moulded polyethylene water storage tanks, capacity in litres 500 (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified and directed.

S&F ball valves 25mm dia, high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm dia and fixed all as specified and directed.

Dismantling of 100mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required all as specified and directed.

S&F in repairs PVC (SWR) pipes 150mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints, fixed to wall in all as specified and directed.

S&F PVC (SWR) pipes 75mm bore, single socketed, in any length with rubber ring joints, fixed to wall in all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) Junction single (Single T) equal or unequal all as specified.

S&F in repairs 110mm bore PVC (SWR) bends of any radius all as specified.

S&F in repairs PVC (SWR) vent cowl all as specified and directed.

S&F in repairs PVC (SWR) 'P' or 'S' trap 110mm bore all as specified and directed..

S&F in repairs square grating doom 150 mm side with or without waste hole of stainless steel consisting of 0.45 mm thick inner and outer cup and 1.0mm thick top grating with ring to be fixed inside 'P' traps with cement concrete all as specified and directed.

S&F for Mild steel work in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; plate washers and similar small articles conforming to FE-290 Gde-E-165 all as specified.

S&F in repairs angular stop cock with wall flange 15 mm dia chromium plated, screwed down, high pressure, screwed both ends for 15mm bore iron pipes or for unionsall as specified and directed. Make-Jaguar Cat No-CQT-29053 or equivalent.

S&F in repairs Towel Ring square with round flange Chromium plated brass screws and plastic cleats of make Jaguar Cat No CAN 1111SM all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm all as specified.

S&F in repairs vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins white or tinted, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed

S&F in repairs Low density polyethylene (LDPE) pipes 32mm dia, of pressure rating 6 kgf/sq. cm all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), (flushing cistern and flush pipe), including plastic water closet seat, white or tinted, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device all as specified and directed..

S&F in repairs PVC valveless, syphonic action type, flushing cistern of 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern all as specified and directed.

S&F in repairs Shower 200X200mm Square Shape Single Flow (ABS Body Chrome Plated with Gray Face Plate) with Rubit Cleaning System all as specified. Make-Jaguar Cat no-OHS-CHR-35497 or equivalent.

S&F Shower Arm 20mm dia & 300mm Long Round Shape with 90˚ Bend for Wall Mounted Showers with Stainless Steel Flange, fixed as in repairs, complete all as specified and directed. Make-Jaguar Cat no-SHA-CHR-479L300S or equivalent.

S&F in repairs stainless steel single tubular towel rail, 20mm dia, D type, 600mm long between flanges of make Jaguar Cat No CAN 1111SM or equivalent all as specified and directed.

S&F in repairs 5mm thick mirror of size 450mm x 600mm mounted on 6mm thick commercial ply wood backing and screwed with PVC channel alround all as specified and directed.

S&F hand shower (Health Faucet) premium quality with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook Make Jaguar cat part No-ALD-573 or equivalent all as specified and directed.

S&F in repairs 6mm thick mirror of any size including rounding and polishing of edges with necessay fittings premium quality all as specified and directed.

S&F in repairs glass corner shelf assembly fancy type made of 5to6mm thick glass of size 250mm fixed with brass CP brackets. Make-Jaguar ACN-CHR-1173N or equivalent.

S&F in repairs stainless steel toilet roll holder with flap all as specified and as directed. Make Jaguar cat part No-ACN-CHR-1153S or equivalent

S&F in repairs soap dish holder premium quality Make Jaguar cat part No-ACN1131N all as specified and directed

S&F in repairs mirror cabinet with Modiguard/Saint Gobain mirror of size not less than 500mmx350mmx125mm premium quality complete or equivalent all as specified

S&F in repairs premium quality single lever extended basin mixer (Height 85mm) without Popup Waste System with 450mm Long Braided Hoses of make Jaguar cat No FUS 29023B or equivalent premium quality.

S&F in repairs premium quality wall mixer system with provision for overhead shower complete with 115mm long bend pipe, connecting Legs & wall Flange of make Jaguar cat No FUS 29281 or equivalent premium quality all as specified and directed..

S&F in repairs 15mm two in one Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed cat No FUS 29041 or equivalent premium quality all as specified.

Taking down shutters of any description exc 1 sq.m and n exc 2 sq.m each all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc. 4 sq. m each all as specified and directed.

M&L for pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed all as specified and directed.

M&L for pressed steel frames of size 165 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed all as specified and directed.

M & L 35mm thick flush shutters factory made solid core construction with block board core and plywood face panels, commercial type on both sides all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutter as in door open rebated and prepared to receive glass, gauge etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR part-I, Sec-08, Clause 8.24(a), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 125mm long Butt hinges, medium weight, cold rolled mild steel, all as specified and directed.

S&F for 200mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed all as specified and directed.

S&F 150mm Aluminium handles, cast type anodised all as specified and directed. .

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in unframed work, in any position all as specified and directed..

M&L 2nd class hard wood Plain fillets. square, rectangular or triangular, n. exc 3sqcm in section, clean sawn, secured with screws all as specified and directed..

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in hold fast blocks including necessary forms work, moulds etc all as specified and directed..

S&F in repair magic eye ball ultra-clear view with wide angle for all round visibility with ultra clear Lens , superior and antique brass finish with 180 degree great visibility to install over a wide range of door thickness up to 35 mm complete all as specified

S&F in repairs 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring all as specified and directed.,

S & F in repair mortice latch with two levers (vertical type), brass body and length of the latch is 65 mm complete all as directed

S&F in repairs 300mm, ordinary rat tail rod pattern springs including roller and roller plate wirh necessary screws to wooden chowkhat or welding to steel door chowkhat complete all as specified.

S&F in repairs curtain rod brackets fancy type brackets with rounded fancy type end knobs, with antique finish or coloured suitable for holding 25mm dia single curtain rods fixed to wall with necessary polished wooden piece 20mm thick exc 50sqcm in section complete all as specified.

S&F in repairs 25mm dia mild steel powder coated, fancy type curtain rod complete all as specified.

S & F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surface of walls including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc. and applying two coat of white washing complete all as specified and directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with one or more all as specified and directed.

M& L 18/19mm thick colour PVC prelaminated board fixed to timber frame work as in cup board shutter / shelves, pelmet box and similar items fixed in repair complete all as directed.

Supplying & fixing of Cutlary Drawer, KUTCHINA/Hettich/Hafele make; Length420mm, Depth-485mm, Height-100mm made of stainless steel of Grade IS:202 complete all as directed.

Supplying & fixing of Plain basket Drawer, UTCHINA/Hettich/Hafele make; Length420mm , Depth-485mm, Height-100mm made of stainless steel of Grade IS:202 complete all as directed.

Supplying & fixing of Thali basket Drawer, KUTCHINA/Hettich/Hafele make; Length420mm, Depth-485mm, Height-150mm made of stainless steel of Grade IS:202 complete all as directed.

Supply & fixing of 6" premium quality Handle, "Kutchina"/Hettich/Hafele make complete all as directed.

M& L Raking out joints/ pointing to masonry or brick-work in single detached joints for flashing, etc all as specified and directed.

Demolition of reinforced cement Concrete in any location n exc 15 cm thickness (below or above ground level) (reinforcement cut as required to facilitate demolition) all as specified and directed.

M&L MS TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending and binding with MS wire annealed not less than 0.9 mm dia all as specified and as directed

M&L for form work to sides and suffits of floor or roof beam, beam haunchings, girders, bressumers, lintels, cantilevers, shelves, including supports overhangs, etc finished rough in flat surface all as specified and directed..

M&L for reinforced cement concrete type B1-1:2:4 (20mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified

M & L for for cleaning using wire brush and washing down with water to remove dust and preparation of the surface for applying crack filler Dr FIXIT or eauivalent over primer on walls nexc 25mm depth and width nexc 10mm of cracks all as specied and directed.

M&L for 40 mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) all as specified.

M&L Providing, cement concrete Cement concrete type B-1,20 mm graded aggregate, 1:2:4 in roof kerbs or mud stops, rounded or chamfered on edges all as specified.

Taking down old damaged existing water proofing membrane of any thickness from roof top complete all as specified and directed.

M&L for water proofing treatment on horizondal or vertical surfaces by applyong oil bound bitumen primer & 0.20 Kg/Sqm and providing 4 mm thick APP modified water proofing membrane weighing not lesss than 4 Kg/Sqm reinforced with non-woven polyester matt weighing not less than 160 gm/sqm including minimum 10 cm side lap and 15 cm end lap torch sealed and bonded and applying a coat of blown grade hot bitumen 90/15 over and below the membrane @ 1.20 Kg/Sqm in drying over the membrane finished with solar reflective bituminus aluminium paint/primer @ 0.1 Kg/Sqm over RCC roof slab/ projection/ parapet after cleaning the surfaces by removing dust dirt etc as manufactures instructions complete all as specified and directed.

Supply only liquid water proofing compound.

M&L for digging out roots of bushes, small trees, grass of any dia & girth from accessible roof projection, chajjas, wall junction, parapet etc at any height by necessay demolition of brick work/ stone masonary/ conrete/ RCC wall or slab etc and filling holes and levelled with cement concrete B-0, 1:2:4 (12.5mm graded stone aggregate) and necessary rendering of cement mortar 1:4 after applying damp proof epoxy based primer and matched with existing surfaces complete all as specified and directed.

Demolition mud/mud phuska in roofs any thickness including plastering tiling and leepig (wheather full thickness removed or only a part thereof

Removing demolished material ie building material concrete stone masonary debris tree roots trunk branches of any type etc to a distance of 30 km or beyond out of premises of metropolition area including loading , unloading by manuallly or by mechanical means (JCB and to be transported through tractor trolly or tipper and staking at the destination as and when directed by Engineer in charge during execution

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth, for foudation etc, or for shafts, wells cesspits, manholes, pier holes etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25 cm thick in soft / loose soil complete all specified and as directed.

M&L for cutting into existing manholes for connecting new drains, making good to 100mm pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required.

M&L hard core of brocken stone or boulders of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface.

Material and labour for 100mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in flooring finished fair and even all as specified and directd

Surface dressing n exc 15 cm deep in soft/ loose soil on uneven surface of natural ground filled up area, removing vegetation, scrapping high patches and filling in low patches with the scrapped soil to give and even & neat look as in road side berms complete all specified and as directed.

Removing excavated material exe 250m but n.exe 500m and upto total distance of 1.5 km depositing where directed.

M&L for 75mm thick Cement concrete type C-2, 1:3:6 (20mm graded stone aggregate) as in flooring, foot path, hard standing, plinth protection, bases of water tanks etc. all as specified.

M& L chequered cement concrete tiles 20cm x 20cm x 25mm thick coloured, set, jointed and pointed in neat cement slurry with grey cement with pigmnts in floors laid over 20 mm thick screed bed in CM 1:4 all as specified and directed.

M & L cement concrete type D-2, 1:4:8, using 40mm graded aggregate as in foundations, fillings and mass concrete.

M&L for reinforced cement concrete type B1-1:2:4 (20mm graded aggregate) as in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc

All as per item No. above but as in Beams, cantilevers, bressummers, lintels

All as per item above but 6 to 8mm dia as in stirups

M&L for rendering 10mm thick cement plaster in cement morter 1:6, on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement.

M&L for preparing new plastered wall surfaces and applying three coats of white wash.

M&L for 100mm thick PCC 1:3:6 type C-2 (40mm graded aggregate) as in sub-base layer.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in flooring, finishing surface even and smooth all as specified.

S&F steel work in tubular trusses including special shaped washer ect. complete using ERW or indluding butt welded tubes conforming to I.S.1161-1998 grade St-240.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed by Engineer-in-charge.

S&F 75mm long Butt hinges, medium weight, cold rolled mild steel,

S&F in repairs steel ventilator with top hung shutter including hinges, steel peg stay, complete

S&F figured glass 3mm thick, pin head type and glazing with oil putty in squares n.exc 0.5 sq.m in each pane

S&F 15mm Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F 15mm pillar tap,cast copper alloy, with capstan head, chromium plated, fancy type screwed down high pressure,with or without lettered "Hot" or "Cold" with long screwed shank and fly-nuts, screwed for iron pipe and fixed all as specified.

S&F concealed/angle stop valve 15mm bore, fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle,screwed both end for ironb pipe or for unions and fixed all as specified.

S&F Brass cromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F Soap dish, any type of size approximate size 160x 60x90mm, fixed to plugs with chromium plated brass screws

S&F Grating doom 100mm dia with or without waste hole of PTMT. (Minimum weight 25gms)

S&F PVC (SWR) pipes 110mm bore, single socketed, in any length with rubber ring joints, fixed to wall

S&F 15mm two in one Bib taps, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified.

S&F Brass chromium plated shower rose 125mm size all as specified.

Mild steel plates, Fe 410-W (Gde-E- 250) quality- A plain or chequered, 5mm thick or over in thickness in available sizes

M&L for cement concrete 1:3:6 type C2 as in bed to 150mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in

M & L cement concerte in surface channels and drains type C-2 1:3:6 using 40mm graded aggregate

Extra for forming fair finished surfaces of drain or channels, inner girth 30 cms, using extra cement including forms, moulds mitred/ stopped ends etc.

S & F Tubes, 'Medium grad',40 mm galvanised, with all fitting; laid in trenches

M&L for machine pressed precast conctete coloured interlocking paver block any shape and size conforming to IS 15658-2006 of 80mm thickness M-40 grade with grey cement and pigments over 25mm thick sand cushioning complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

S & F of Steel rolling shutters, thickness of laths 1.25mm with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type.

S&F safety lever locks mild steel with 4 levers for rolling shutters fixing complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in flooring all as specified.

M&L for preparation of old decorated surface as in ceiling including washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of distemper oil emulsion complete.

M&L Cement concrete 1:4:8 type D2 using 40mm graded agg 75 mm thick as in sub base of floor etc complete all as specified and directed

M&L Cement concrete 1:2:4 type B1 using 20mm graded agg 50 mm thick for flooring complete all as specified and directed

M&L Cement concrete 1:2:4 type B0 using 12.5mm graded agg 40 mm thick for DPC incl necessary form work etc complete all as specified and directed

Glass dividing strips 22mm wide and 3 mm th complete all as directed.

M&L for 100 mm thick PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection, surfaces, finished even and fair (without using extra cement) complete all as specified & directed.

Supply & fix MS work for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 (Gde E-165) complete all as specified & directed.

Mild steel, plain, black sheet 1 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required®

Supplied & fixed Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed .

S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified & directed.

Material & labour for mild steel work as in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified & directed.

S & F 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/shank/moulded/decorative surface as required decorative cornice over 2ndclass soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)and applying two coat of Distempering on new ceiling with distemper oil emulsion white or tinted complete over 3 mm providing and applying plaster of paris putty 2 mm thickness over new surface to prepare the surface even and smooth complete all as specified and directed.

Anodised aluminium snap grid frame work for false ceiling all as specified

S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M &L for fixing partly glazed partition of different height from floor with 12mm thick interior grade phenol formaldehyde bonded as per IS3087 melamine faced both sides prelaminated particle board/ MDF board of approved shade and manufacturer and glazed portion as per drawing & direction middle portion with 8 mm thick tinted glass in aluminium frame work consisting of rectangular section of size approx.62.5x37.10x2mm ,glazing clip section no 4660 of Jindal / Hindalco etc . Rate to allow for anodizing the aluminium sections in powder coated colour as directed by the Engineer in charge

S&F anodised aluminium frame powder coating, for doors, windows, ventilators, Partition/fixed type windows, aluminium grill etc. with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F one way mirror glass of 6.0mm thick fix to aluminium frame work all as specified and directed by Engr-in-charge .

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing ®

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Providing and fixing of Protrack spendex system on GI studs 2400mm x 50mm web flamges 15&50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing 50mm thick rock wool @48kg density insulation intact with chicken mess wires. 600x1200x15mm Magnetite pine wool tile with NRC 0.9-1 to be mechanically fastened on the G.I Studs. Then 12mm clip rail system are screw fixed on to the 12mm MDF waterproof and Acoustics panel's. Then the spandex is stretched over the clip rail system. The istalled system should provide NRC OF 1.00, Spandex colour as per Architect choice-Ref attached specifications for more details. The system to be installed on G.I studes 600x600mm center 2400mm x 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurl giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration.

Taking down carefully U/S aluminium/ copper point wiring (light, fan,socket or power) complete with fittings such as switches, sockets, ceiling rose, light fittings etc , removing all material for reuse/ issued under sch of credit and making good the distrubed surface as the existing one, complete all as directed.

Taking down ceiling fan & dismantaling blades & refixing of the same including provision of suitable size of fan down rod below the false ceiling height as per the site requirement, Painting of Ceiling Fan complete with Syntetic enamel paint by spray painting including filling patty work connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed.

Material & Labour for taking out Geyser from the old location of any capacity & refixing all as directed

Material & Labour for taking out Exhaust fan from the old location of any capacity & refixing all as directed

Point wiring complete with Multi stranded copper conductor size 1.5 sqmm PVC insulated, unsheathed,FRLS cable , 1100 volts grade conforming to IS 694 multistranded , drawn in and including rigid PVC surface type conduit on walls/ floors/ ceiling etcwith and including metal flush boxes of suitable size and modular white plate with frame for mounting of fittings, modular type switches, regulator and also including 1.5 sqmm PVC insulated unsheathed copper cable green in colour as continuous earth continuity conductor and connecting to earth dolly,cutting chasis to the wall s/ floors/ ceiling and repairing with existing surface after work ,complete all as specified and directed.

One light point controlled by one way switch

One Ceiling fan / Exhaust fan point controlled by one way switch

One 3 pin socket point 5 Amps on independent board.

One 3 pin socket point 5 Amps on Same board.

One light controlled by two, way 5 Amps switches.

One bell Point controlled by one push button 5 Amps switch on independent board

All as per item No 203 here-in-before but using copper conductor 2.5 sqmm PVC insulated unsheathed FRLS cable with copper conductor size 2.5 sqmmm PVC insulated unsheathed continuous earth continuity for 3 pin 15 amps socket outlet independently.

Cutting chasis, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings etc, for concealed conduit wiring a into or through the stone walls built in cement mortar or cement lime mortar and walls of cement concrete suitable for housing 25mm dia conduit pipe using heavy duty stone drilling/cutter machine and making good the disturbed surface all as specified and directed.

Supply & fix ceiling rose surface backelite two to three terminal complete all as directed.

Supply and Fixing of Bell, AC, 230 volts, Single Pole

Supply & fix switch modular type single pole 1 way 5 Amp 230 volt complete as directed.

Supply and Fixing of modular type Bell push 6 A, 1 Module

Supply & fix switch modular type single pole 2 way 5 Amp 230 volt complete as directed.

Supply and fixing of modular type fan regulator upto 300 watts with 5 step speed control for fans any sweep 1200 mm/1400 mm.

Supply & fix socket combination 6 Amps modular type, 230 volts grade all as directed.

Supply & fix Socket combination 6A/16A - modular type 230 volts grade with frame and cover all as specfied.

Supply & fix switch modular type single pole 1 way 16 Amp 230 volt complete as directed.

Supply and fixing of modular white cover plate with frame, 1 module

Supply and fixing of modular white cover plate with frame, 2 module

Supply and fixing of modular white cover plate with frame, 3 module

Supply and fixing of modular white cover plate with frame, 4 module

Supply and fixing of modular white cover plate with frame, 6 module

Supply and fixing of modular white cover plate with frame, 8 module

Supply and fixing of metal flush box 1/2 module

Supply and fixing of metal flush box 3 module

Supply and fixing of metal flush box 4 module

Supply and fixing of metal flush box 6 module

Supply and fixing of metal flush box 8 module

Supply and fixing of LED Light fitting of 40 Watts, 220 volts, Batten type with driver, holder including LED tube light connecting up with flexible copper conductor cable of suitable size from Ceiling rose. Make CG, Model : TRIMELINE, CAT : LDL-40-WM or equivalent in HAVELLS /BAJAJ /PHILIPS

Supply and fixing of LED Light fitting of 10 Watts, 220 volts, Batten type with driver, holder including LED tube light connecting up with flexible copper conductor cable of suitable size from Ceiling rose. Make CG, Model : TRIMELINE, CAT : LDL-10-WM or equivalent in HAVELLS /BAJAJ /PHILIPS

Supply and fixing of LED Street Light fitting of 45 Watts, 220 volts, IP 65/66 Protection complete with driver, holder including connecting up with 2 core flexible copper conductor cable of suitable size. Make CG, Model : FREEDOM NEO, CAT : LSTS-25-CDL-M or equivalent in HAVELLS /BAJAJ /PHILIPS

M&L for sub main wiring complete with 2 runs of 4.00 Sqmm PVC insulated and unsheathed cable with multistranded copper conductor confirming to IS-649, 1100 volts grade and drawn through and including PVC non metallic rigid conduits and conduit accessories concealed / run on surface of wall/floors/ ceiling etc and connecting terminal ends including 1 run of 4.00 Sqmm of PVC insulated unsheathed copper conductor cable green colour as continuous earth continuity conductor and connecting to earth dolly including removing unserviceable sub main wiring complete all as directed and specified.

Supply and fixing of DB, SPN 8 ways, Double door type complete all as specified and as directed

Supply & fix 'C' Curve MCB SP 6 to 32 Amps 240 volts 10 KA rupturing capacity complete all as directed Make : Legrand or eqivalent in C&S/Scheinder/Havells

Supply & fix MCB SPN 6 to 40 Amps 240 volts 10 KA rupturing capacity complete all as directed Make : Legrand or eqivalent in C&S/Scheinder/Havells

Material and labour for Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground ( earth pit not less than 2.25mtrs deep below ground level) with top edge of the plate not less than 1.5mtrs below normal ground level, connected to galvanised iron earth lead 4 mm dia as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indiacted including testing on completion.

Supply & fixing of Galvanised steel wire 4.00 mm Dia

Taking down Existing light fittings of any description from wall/ ceiling including keeping in safe custody by making good the disturebed surfaces of walls all as specified and as directed

Point wiring with cable of PVC insulated FRLS copper multistranded conductor 2.5 sqmm 1100 volts grade in and including heavy grade PVC Conduit Pipe ISI marked broken white/or of cream /grey colour. with all accessories and fixing arrangements on wall/ceiling/floor surface on wall including top cover/PVC gang box fixing on wall surface for housing switches/sockets/regulators etc. with and including 2.5 sqmm PVC insulated multistranded copper earth continuity conductor connecting to the common earth dolly etc complete all as specified and directed for one 15A Switch Socket Combination on independent board all as specified and as directed.

Supply and fix Modular switch , 1 Module single pole one way 10 Amps.

Supply & fixing of PVC Conduit pipe for fire wiring of size 20 mm dia

Supply & fixing of PVC Conduit pipe for fire wiring of size 25 mm dia

Supply & fixing of PVC Conduit pipe for fire wiring of size 32 mm dia

Supply & fixing of PVC Conduit pipe for fire wiring of size 40 mm dia

Supply and fix office LED Luminaires type 36 watts, LED 600 x 600 mm grid ceiling incl connecting up with PVC sheathed 1.5 sqmm 2 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed. Make :CG, VECTOR -VII, Cat : LCTLRF7 or equivalent make in Philips/Wipro/ POLYCAB

Supply and fixing of LED batten luminaire surface mounted, 4 feet light fitting 20 Watts Make : CG, TRIMLINE, MODEL LDL-40 WW make in Philips/Wipro/ POLYCAB

M&L for cement concrete 1:2:4 type B1 (20mm grade stone aggregate) as in filling hollow portion of pressed steel frame complete all as specified and directed

SRI GANESH ENTERPRISES