Design, Engineering, Supply, Erection and Commissioning of prefab building structure for ITI in Maharashtra State at Consignee Locations

Excavation In soil SSR 22-23 / Item No. 21.02 / Pg 141

Excavation In soil SSR 22-23 / Item No. 21.06 / Pg 141

Excavation In soil SSR 22-23 / Item No. 21.14 / Pg 142

Excavation for foundation in Hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m.) By Mechanical Means [Bd.A.2 Page No. 259] SSR 22-23/ Item No. 21.08 / Pg 142

Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 m). By Mechanical Means [Bd.A.6 Page No. 260] SSR 22-23/ Item No. 21.20 / Pg 143

Excavation for foundation in laterite rock (soft or hard) including trimming and levelling the bed for the foundation, removing the excavated material up to a distance of 50 metres beyond the building area, stacking as directed, dewatering and back filling with available murum, watering, ramming etc. complete. (Lift upto 1.5 m.) By Mechanical Means [Bd.A.7 Page No. 260] SSR 22-23/ Item No. 21.21 / Pg 143

Providing preconstructional antitermite treatment as per S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyri fos per square meter surface area covering 10 years guarantee on bond paper. Spec. As directed by Engineer in charge. SSR 22-23 / Item No. 21.22 / Pg 143

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper. As directed by Engineer in charge. SSR 22-23 / Item No. 21.24 / Pg 143

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diameter about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper. As directed by Engineer in charge. SSR 22-23 / Item No. 21.25 / Pg 144

Providing dry/trap/granite/quartzite/gneiss rubble stone soling 15 cm to 20 cm thick including handpacking and compacting etc.complete. [Bd.A. 12 Page One Number 264 SSR 22-23 / Item No. 21.38 / Pg 145

Filling in plinth and floors with contractors material / brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. [Bd.A.11 Page No. 263] SSR 22-23 / Item No. 21.37 / Pg 145

Providing and filling in the foundation with sand of approved quality including watering, compacting etc. complete. (To be executed with prior approval of Superintending Engineer) [Bd.A.13 Page No. 264]

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all loads including all lifts involved. for 50 Km Lead SSR 22-23 / statement C / Pg 485

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) [Bd. E. 1 Page One Number 287] SSR 22-23 / Item No. 24.01 / Pg 163

Providing and laying Cast in situ/Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) [Bd.E.2 Page One Number 288 and B.7 Page No 38] SSR 22-23 / Item No. 24.06 / Pg 163

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) [Bd.E.4 Page One Number 289 and B-7, Page One Number38] SSR 22-23 / Item No. 24.10 / Pg 164

Providing and laying in situ /Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete . With fine aggregate (Crushed sand VSI Grade) [Bd.F.3 Page One Number 298 and B.7, Page One Number38] SSR 22-23 / Item No. 25.11 / Pg 166

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) [Bd.F.5 Page One Number 300 and B.7, Page.One Number 38] SSR 22-23 / Item No. 25.31 / Pg 167

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) [Bd.F.6 Page One Number 300 and B.7, Page One Number38] SSR 22-23 / Item No. 25.50 / Pg 169

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) [Bd.F.8 Page One Number 302 and B.7, Page One Number38] SSR 22-23 / Item No. 25.70 / Pg 170

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for foundation and bedding / steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 22-23 / Item No.24.04 / Pg 163

Providing and laying Cast in situ/Ready Mixcement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 22-23 / Item No.26.05 / Pg 172

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for R.C.C. canopy as per detailed designs and drawings including steel centering, formwork, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing etc. complete (excluding reinforcement), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 22-23 / Item No.26.09 / Pg 172

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and rougheningthem if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 22-23 / Item No.26.17 / Pg 173

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 22-23 / Item No.26.23 / Pg 173

Providing and fixing in position TMT FE 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. [Bd.F.17, Page No. 306] SSR 22-23 / Item No. 26.33 / Pg 176

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. [Bd.F.17, Page No. 306] SSR 22-23 / Item No. 26.34 / Pg 176

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. [Bd.C.2 Page Number 275] SSR 22-23 / Item No. 23.01 / Pg 161

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. [Bd.C.2 Page Number 275] SSR 22-23 / Item No. 23.02 / Pg 161

Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete. [Bd.C.8 Page Number 161] SSR 22-23 / Item No. 23.04 / Pg 161

Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete. As directed byEngineer in Charge. SSR 22-23 / Item No. 23.11 / Pg 162

Providing and constructing masonry in precast solid Concrete Block (Grade D-50 As per I.S. 2185, Part-I, 1974, Reframed 1987) having compressive strength 5-00 N/mm2) of size (300 mm x 200 mm x 150mm) in cement mortar 1:6 for superstructure including striking joints on unexposed faces, racking out joints on exposed faces, watering, curing and scaffolding etc. complete. [As directed by Engineer in Charge.] SSR 22-23 / Item No. 27.15 / Pg 186

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) [As directed by Engineer in Charge.]

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) [As directed by Engineer in Charge.] SSR 22-23 / Item No. 27.16 / Pg 186

Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. As directed by Engineer in Charge SSR 22-23 / Item No. 32.26 / Pg 198

Providing internal cement plaster 6 mm thick in a single coat using Ready to use ceiling & wall plaster in cement mortar 1:3 to concrete surface in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. With Prior Approval of Concerned S.E., As directed by engineer in charge SSR 22-23 / Item No. 51.109 / Pg 367

Providing internal / external 12 mm thick Ready Mix plaster confirming to IS:4031 (Part-4) 1988 and IS383 -1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, toall type of surfaces in all positions including scaffolding and curing complete. As directed by Engineer Incharge SSR 22-23 / Item No. 51.117 / Pg 371

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete. As directed by Engineer in charge. SSR 22-23 / Item No. 32.34 / Pg 200

Providing internal / external 20 mm thick Ready Mix plaster confirming to IS:4031 (Part-4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4%, to all type of surfaces in all positions including scaffolding and curing complete. As directed by Engineer Incharge SSR22-23 / Item No. 51.118 / Pg 371

Labour charges for providing groove in external plaster having width and spaced as directed by engineer incharge etc. complete. SSR 22-23 / Item No. 32.22 / Pg 198

Add for plaster drip course in plastered surface or moulding to R.C.C. projections. DSR 2021 Part 1 / Item No. 5.30 / Pg 128

Providing and applying two coats of protective membrane over the cured concrete surface like R.C.C. footings, columns, plinth beams etc. which will be submerged under soil so as to protect the same. Apply two pack coal tar epoxy system of Sunepoxy Coaltar of approved make & approved by Engineer in charge, having solid content ranges from 80-100%, Tack free time 4-6 hrs. Recoat after 16-24 hrs. Mix Part A and Part B of Sunepoxy Coaltar of approved make & approved by Engineer in charge in 1:1 ratio with slow speed stirrer and apply the same on a clean R.C.C. surface by brush. Allow to set for 8-10 hours and apply the second coat. The rate to include for application at all levels to various RCC elements to the satisfaction of the EIC etc. complete. [ As directed by Engineer Incharge] SSR 22-23 / Item No. 50.06 / Pg 317

Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc.complete. As directed by Engineer in charge. SSR 22-23 / Item No. 31.05 / Pg 205

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vIrgin concrete slab with waterproofing compound @ 1kg/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 kg/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. As directed by Engineer in charge SSR 22-23 / Item No. 31.26 / Pg 196

Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge) SSR 22-23 / Item No. 31.06 / Pg 193

Providing & Making Waterproofing Treatment to the Chajja by finishing top surface with 20 mm thick 12 C.M. plaster with addition of approved water proofing compound as per manufacturers specifications and neat cement finish,including drip moulding at edge ,at bottom of chajja & cement vatta above chajja along the junction with wall etc complete. as per FMB item No. 5.22 but for new surfaces & as directed by the Engineer-In-Charge. MCGM-USOR-2023 / Item No.R3-CS-WP-49 / Pg 64

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590mm to 605 mm x 590 mm to 605 mm of 8to10 mm thickness and confirming to IS.15622 -2006 (group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. [Bd.M. 12 Page No.385] SSR 22-23 / Item No. 33.40 / Pg 205

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. [Bd.M.12 Page No. 385]SSR 22-23 / Item No. 33.44 / Pg 205

Providing sills of polished Kota stone 25mm to 30mm thick, on a bed of 1:4 cement mortar including cement float, filling joints with slurry, curing, moulding edges, polishing and cleaning etc. complete. [Bd.M.29 Page No. 391] SSR 22-23 / Item No. 33.19 / Pg 202

Providing and laying 2mm thick antifungal self levelling Epoxy flooring on concrete substrate including coving at floor wall junction & including necessary surface preparation using cleaning, dedusting, applying suitable primer including Aisle or zone marking in different colours etc. complete as per manufacturers specifications and as directed by Engineer In Charge.MCGM-USOR-2023 / Item No.R3-CS-PN-24 / Pg No. 70

Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. [Bd.M.22 Page No. 390] SSR 22-23 / Item No. 33.18 / Pg 202

Providing and laying ceramic tiles having size 30cm. x 45cm. confirming to corresponding I.S. for dado and skirting in required position with ready made adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white / colour cement slurry cleaning curing etc. complete. [Bd.M.13 Page No. 386.] SSR 22-23 / Item No. 33.26 / Pg 203

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. [Bd. M.22 B/Page No. 390]SSR 22-23 / Item No. 33.35 / Pg 203

Providing and laying telephone black / Amba White / Cadbury brown / Rubyred / Ocean Brown granite stone of 18 to 20 mm thick for door frame / dado / window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges where ever necessary, curing, etc. complete. As directed by Engineer-In- Charge SSR 22-23 / Item No. 33.68 / Pg 208

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. SSR 22-23 / Item No. 33.56 / Pg 207

Providing and laying C.C. floor of mix M-20 with ready mixed concrete from RMC. The ready mixed concrete shall be laid and vibrated with a poker vibrator and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. The channel shuttering spaced 4m apart shall be included in this item.) MCGM-USOR-2023 / Item No.R3-CS-CW-24 / Pg 16

Providing and laying chequered/ paver tiles of approved quality of size 30cm x 30cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.SSR 22-23 / Item No. 33.66 / Pg 208

Providing and fixing heavy duty inter locking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60 millimeter thickness of having a strength of 400 Kilogram/sq.m of approved quality and shape on a bed of crushed sand of 25 to 30 millimeter thick including striking joints and cleaning etc. complete. (using 100% crushed sand)SSR 22-23 / Item No.33.53 / Pg 207

Providing and fixing fire doors with 2 hour fire rating conforming to IS: 3614 (Part 2), BS 476 (Parts 20 & 22), ISO 834 ; 45 mm thick fully flush, double skin door shell with lock seam joints at stile edges made from 1.25 mm thick galvanized steel sheet including door frames made from 1.6 mm thick galvanized steel sheet formed to double rebate profile of size 143 mm x 57mm as per manufacturer's instructions, door frames and shutter primed with Zinc Phosphate stoving Primer and finished with Polyurethane Aliphatic grade or epoxy paint including ironmongery consisting of stainless steel ball bearing butt hinges 3 mm thick fixed flush to the frame and shutter, full width horizontal handles (panic bar), concealed flush bolts, door closers, other standards fixtures and fasteners, etc. complete for the following clear opening sizes: including heavy duty SS hinges min 4 per shutter, tower bolts, door stoppers, handles, mortise lock, push plates, kick plates, door closers, etc. Complete. - Refer RA65 MCGM SOR 2018 Bldg Part 1 / R2-CS-WW-31/ Pg 109

Providing and fixing frame with / without ventilator of size as specified with Country non teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete. SSR 22-23 / Item No.39.02/ Pg 233

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. [BD-T-34 Page One Number 499] SSR 22-23 / Item No. 39.09 / Pg 234

Solid Core Flush door Double leaf Providing and fixing factory made solid core flush door shutters in double leaves 35mm thick,decorative type of exterior grade, as per detailed drawings, conforming to I.S.: 2202 – 1966 (Revised) including approved face veneers on both sides, without glazing and venetians including mat finish stainless steel fixtures and fastening, stoppers and finishing with french polishing etc. (Excluding door frame)(Sample to be got approved from Ex. Engineer before use) Commercial Hard Wood shutter SSR 22-23 / Item No. 51.61 / Pg 356

Providing and fixing fiber glass reinforced polyster door shutter 30 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete SSR 22-23 / Item No. 39.58 / Pg 245

Providing and fixing steel frame door of angle 50 x 50 x 6 mm with mild steel bars 16 mm dia. Horizontally at 10 mm c/c for ventilator portion including iron hold fast boxes for fixing shutters including welding, finishing, painting etc. complete. As directed by Engineer incharge. SSR 22-23 / Item No. 39.35 / Pg 238

Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/One Running Metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating with box SSR 22-23 / Item No. 39.43 / Pg 242

Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension ?63.50 x 38.10 x 1.02 mm at weight 0.547 Kilogram/One Running Metre. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 Kilogram/One Running Metre. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 Kilogram/One Running Metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/One Running Metre. And handle section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/One Running Metre. and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With powder coating without box SSR 22-23 / Item No.39.40/ Pg 240

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. SSR 22-23 / Item No. 39.68 / Pg 248

Providing and fixing in position factory made box type fully glazed window consisting of cold rolled section of 105mm x 60mm x 1.25mm thick frame section filled with cement concrete (1:2:4) and steel section F4B as per detailed drawing and design including mild steel 12mm square bars at 10cm center to center, required F7B section, section T6, section for shutter frame (Louvered clips in case of Louvered window portion) and 3mm thick glass of approved quality of necessaryfixtures and fastening, finishing with one coat of anticorrosive paint etc. complete . SSR 22-23 / Item No.39.23/ Pg 236

Providing and applying white-wash in two coat on old / new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete. [Bd.P.1 Page Number 411] SSR 22-23 / Item No. 36.03 / Pg 215

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying wash able oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete. [Bd.P.5 Page Number 413] SSR 22-23 / Item No. 36.11 / Pg 215

Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. etc. complete. [Bd.P.6 Page Number 414 Square Metre] SSR 22-23 / Item No. 36.12 / Pg 215

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. As directed by Engineer in charge. SSR 22-23 / Item No. 35.23 / Pg 213

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller. (With prior approval of S.E.) SSR 22-23 / Item No. 36.21 / Pg 217

Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete. SSR 22-23 / Item No. 35.07 / Pg 211

Providing and fixing Wall Mounted European type white glazed earthen ware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC And vent pipe upto the outside face of wall 10 liter enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps, 20 mm dia. UPVC over flow pipe, mosquito proof couplings G.I. chain and pulley, with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete. (prior approval of sample and brand by Ex. Engineer is necessary before use) State SSR 22-23 / I.N. 43.44 / Pg. 280

Providing and fixing European type white glazed earthen ware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the out side face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps, 20 mm dia. UPVC over flow pipe, mosquito proof couplings G.I. chain and pulley, with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete. (prior approval of sample and brand by Ex. Engineer is necessary before use) State SSR 22-23/I.N. 43.19 / Pg. 277

Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall. (Bd.V.23 Page One Number 562) State SSR 22-23/I.N. 41.57 / Pg. 259

Providing and fixing JAQUAR MAKE metropole flush valve Dual Flow Concealed type with control cock operation plate 40 mm size etc. Complete MCGM Bldg SOR/I.N. R2-CS-PS-244 / Pg. 206

Providing and fixing C.P. Two way BIB cock of approved make continental including necessary sockets/union nut etc. complete. State SSR 21-22/I.N. 42.80 / Pg. 271

Providing and fixing Health Faucet with one metre long easy flex tube in chrome finish and wall flange MCGM Bldg SOR/I.N. R2-CS-PS-204 / Pg. 165

Providing and fixing white glazed earthen ware Wash Hand Basin of 55 cm. x 40 cm. size including cold water pillar tap, cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the out side face of the wall. Making good the damaged surface, testing etc. complete. State SSR 22-23/I.N. 41.63 / Pg. 260

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete. SSR 22-23 / Item No.42.33/ Pg 265

Providing and fixing white glazed earthen ware Wash Hand Basin of 45 cm x 30 cm size including cold water pillar tap, cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. State SSR 22-23/I.N. 41.64 / Pg. 260

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. State SSR 22-23/I.N. 42.78 / Pg. 270

Providing and fixing C.P. sink cock with raised J" shaped swinging casted spout of approved make including necessary sockets/ union nut etc. complete. State SSR 22-23/I.N. 42.84 / Pg. 271

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore MCGM Bldg SOR/I.N. R2-CS-PS-131 / Pg. 153

Modelno. ALD-769 B Bottle trap (with internal partition) for Wash Basins including Waste Coupling fixed in required position with 250mm long wall connection pipes and wall flange with all necessaryfittings and fixtures, etc. complete and as directed by The Engineer incharge. MCGM Bldg SOR/I.N. R2-CS-PS-262 / Pg. 208

Providing and fixing toilet paper holder : C.P. Brass MCGM Bldg SOR/I.N. R2-CS-PS-33-a / Pg. 138

Providing and fixing ISI marked make CP brass liquid soap dispensers with CP brass bracket capacity 250 ml. MCGM Bldg SOR/I.N. R2-CS-PS-261 / Pg. 207

C.P.Soap dish hooker jaquar make continental (Cat. No. AKB 35731 )

C.P.Towel rail 24" jaquar make continental (Cat. No. ACN 1111N )

Supplying and erecting storage type horizontal / vertical water heater 25 litres capacity with BEE 5 star rating high impact resistance engineering plastic body on wall / loft complete duly tested and marking sr. no. and date of erection. specification no.AP-WH/STWH ( Make: Jaquar , Model : Elena Digital or equivalent) MSR 21-22 / Item No. 3-1-3 / Pg No.45

Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water 7 to 8 litre/min with activated carbon filter and softener operating on 230 V single phase A.C.supply. MSR 21-22 / Item No. 3-5-1 / Pg No.51

Supplying, erecting, testing and commissioning selfcontained water cooler 230/250 V 50 cycles nominal cooling capacity of 80 litres/hr and storage capacity 120 litres with partially stainless steel body complete. specification no. AP-WCR/WC MSR 21-22 / Item No. 3-3-4 / Pg No.50

Providing, laying and fixing P.V.C. pipe of 15mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 22-23 / Item No. 42.21 / Pg 264

Providing,laying , testing & commissioning of 20mm dia PVC pipes including all necessary fittings such as bends; tees, single/double junction, filling the joints with solvent cement incl. necessary trenching & refilling etc. complete. SSR 22-23 / Item No. 42.22 / Pg 264

Providing, laying and fixing P.V.C. pipe of 25mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 22-23 / Item No. 42.23 / Pg 264

Providing, laying and fixing P.V.C. pipe of 32mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 22-23 / Item No. 42.24 / Pg 264

Providing, laying and fixing P.V.C. pipe of 40mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 22-23 / Item No. 42.25 / Pg 264

Providing and fixing 160 mm dia pipe/ P.V.C. soil vent / waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Downtakes 160 mm dia. Soil Pipe

Providing and fixing 100 mm dia pipe/ P.V.C. soil vent / waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Internal toilets 100 mm dia. Soil Pipe Downtakes 100 mm dia. Waste pipe SSR 22-23 / Item No. 42.52 / Pg 268

Providing and fixing 75mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. Internal toilets 75 mm dia. Waste pipe Downtakes 75 mm dia. Soil Vent pipe SSR 22-23 / Item No. 42.51 / Pg 268

Providing, laying and fixing P.V.C. pipe of 32mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Internal for Wash basins SSR 22-23 / Item No. 42.24 / Pg 264

Providing, laying and fixing P.V.C. pipe of 50mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Internal Toilets SSR 22-23 / Item No. 42.26 / Pg 264

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge (15 mm dia pipe) Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes MCGM SOR Bldg / R2-CS-PS-86-a/ Pg 146

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge ( 20 mm dia pipe) Concealed work, including cutting chases and making good the walls etc. 20mm nominal outer dia. Pipes MCGM SOR Bldg / R2-CS-PS-86-b/ Pg 146

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. ( 20 mm dia pipe) External Work 20 mm nominal outer dia Pipes (Downtake) MCGM SOR Bldg / R2-CS-PS-87-b/ Pg 147

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External Work 25mm nominal outer dia. Pipes MCGM SOR Bldg / R2-CS-PS-87-c/ Pg 147

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External Work 32mm nominal outer dia. Pipes MCGM SOR Bldg / R2-CS-PS-87-d/ Pg 147

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External Work 40mm nominal outer dia. Pipes MCGM SOR Bldg / R2-CS-PS-87-e/ Pg 147

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External Work 50mm nominal outer dia. Pipes MCGM SOR Bldg / R2-CS-PS-87-f/ Pg 147

Providing & Fixing PVC ball valve as per ISO:138 / IS-7834 for the operating temperature upto 90 Deg.C & maintenance threaded or plain socket type for domestic,flushing & Hot water supply.

20mm Dia.

25mm Dia.

32mm Dia.

40mm Dia.

50mm Dia.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : MCGM-USOR-2023 / Item No.R3-CS-PS-96 / Pg No.180

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. MCGM-USOR-2023 / Item No.R3-CS-PS-140/ Pg No.188

15 mm nominal bore, 105 mm long, weighing not less than 138 gms

20 mm nominal bore, 120 mm long, weighing not less than 198 gms

25 mm nominal bore, 152mm long, weighing not less than 440 gms

40 mm nominal bore, 206mm long, weighing not less than 690 gms

50 mm nominal bore, 242mm long, weighing not less than 1240 gms

Providing and fixing pressure reducing station PN16 rating,Brass construction including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required.The complete system is tested to a pressure not less than 16 Kg/Sq.cm and suitable to reduce the pressure upto 1.5 Kg/Sq.cm. of 20mm Dia.

20mm Dia.

Providing & fixing 25mm pressure reducing valve on down take water supply - 25 mm Dia. MCGM SOR Bldg /R2-CS-PS-242/ Pg 206

Providing & fixing 32mm pressure reducing valve on down take water supply (diaphragm type with inbuilt ss strainer) - 32 mm Dia. MCGM SOR Bldg / R2-CS-PS-241/Pg 206

Providing & fixing 40mm pressure reducing valve on down take water supply pipes (diaphram type with inbuilt ss strainer) 40 mm Dia. MCGM SOR Bldg / R2-CS-PS-240/Pg 206

Supplying & Fixing & Testing Pressure reducing Valve of Diaphram type & inbuilt SS strainer type with necessary connectors. c) 50 mm (2") dia. 50 mm Dia. MCGM SOR Bldg / R2-CS-PS-239-c/Pg 206

Providing and fixing single acting Air release valve with Screwed inlet 25mm MCGM SOR Bldg / R2-CS-PS-282/Pg 209

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete SSR 22-23 / Item No. 41.80 / Pg 261

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) as per standard design : 1) 100x100 mm size P type, 2) With Sewer bricks conforming to IS : 4885 MCGM Bldg SOR / R2-CS-PS-166-a-2 / Pg - 157

Providing and constructing Brick Masonry Inspection Chamber 60 cm x 45 cm x 90 cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channel shalf round G.S.W. pipes, Brick Masonry, plastering from inside. [Bd.V.43, Page One Number 574] State SSR 22-23 / 42.10 / Pg - 262

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight with 75 mm thick R.C.C. cover medium duty 140Kilogrametc. complete. SSR 22-23 / Item No.42.17/ Pg 263

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. SSR 22-23 / Item No. 42.07 / Pg 262

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. SSR 22-23 / Item No. 42.08 / Pg 262

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. SSR 22-23 / Item No. 42.09 / Pg 262

Providing, Fixing, testing and commissioning of ISI marked Gun Metal Screwed pattern fully way Gate valve conforming to IS 778 class 1 including jointing, supporting etc complete and as directed.

Dia. 80mm DSR 2021 Part 2/ Item No. 18.17.6 / Pg No.402

Dia. 50mm DSR 2021 Part 2/ Item No. 18.17.4 / Pg No.402

Dia. 40mm DSR 2021 Part 2/ Item No. 18.17.3 / Pg No.402

Dia. 32mm DSR 2021 Part 2/ Item No. 18.17.2 / Pg No.402

Providing and fixing gun metal non- return valve of approved quality (screwed end) including rubber gasket, flanges, union, nuts, bolts, washers & painting complete as required.

Dia. 80mm DSR 2021 Part 2 / Item No. 18.19.6/ Pg No.403

Dia. 50mm DSR 2021 Part 2 / Item No. 18.19.4/ Pg No.403

Dia. 40mm DSR 2021 Part 2 / Item No. 18.19.3/ Pg No.403

Dia. 32mm DSR 2021 Part 2 / Item No. 18.19.2/ Pg No.403

Providing & fixing of 'Y' strainer with necessary fittings to be installed in the tank sump.The body shall be of high grade cast iron GG 250 with internal & external epoxy coated with Stainless Steel filter element upto 1600 microns, with a drain plug, PN 16 Rating upto size 150mm & PN 10 for size 200mm & above.Strainer shall be installed on full size of pipe run , in accordance with the manufacturer's installation instructions. Y type Strainer Screwed ends for water filter. The body shall be of Brass. The filter element shall be of Stainless Steel with Mesh :500 Microns Pressure PFA 25 bar. Cap delivered with plug (nylon66) 1/4" G.

Dia 80mm

Dia 50mm

RWH - Shallow Percolation Pit providing ,constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia. pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth(from bottom up) with 25-75 mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate(natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lift sat all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge. SSR 22-23/ 48.46/ Pg 317

RWH - Recharge Pit Providing and constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast RCC rings with 6.5" dia x 25 m deep borewell at the floor of recharge pit including installation of combination of solid/ perforated PVC casing pipe wrapped around with netlon mesh including 300 mm thick side filling around outside of RCC rings (annularspace) with 40 mm size boulders including filling of recharge pit upto 0.5 m depth with 25 -75 mm clean washed gravels from bottom up followed by 0.5 m depth of 10- 25 mm of clean washed stones followed by 0.5 m of washed river fine aggregate (naturalsand/ crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/ fine aggregate (naturalsand/ crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, man hole frame & cover, PVC rungs, PVC end-caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in Charge. SSR 22-23/ 48.47/ Pg 305

Providing & fixing SS 304 grade V wire filter for each borewel the diameter of V wire is 150 mm and length is 500 mm etc complete as directed by Engineer Incharge.

Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. SSR 22-23 / Item No. 42.07 / Pg 262

Providing, hoisting and fixing at all level precast reinforced cement concrete work in string courses, bands, copings, drain covers, bed plates, anchor blocks, plain window sills and the like including the cost of required centering, shuttering and reinforcement, of Nominal Mix 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) MCGM Bldg SOR/ R2-CS-CW-4-b/ Pg 12

Providing, fabricating and fixing M.S. grill work as per approved design and as per weight specified below to fencing / compound mades out of square / round bars, M.S. flats, angles, with necessary holdfast including painting with one coat of red oxide zinc chromate primer and two coats of approved synthetic enamel paint etc. complete as directed by Engineer In Charge. - Mild steel grill of weight 20 to 25 Kg/sq. m. MCGM Bldg SOR/ Item No. R2-CS-SL-14-c/ Pg 102

Providing and Fixing mat finish stainless steel (of 302 grade) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing, fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex. Engineer is necessary before use) SSR 22-23 / Item No. 40.08 / Pg 265

Planting Lawn by filling without excavation (Flat surface/Mound): Providing and filling Red Hill Earth & Cow Dung Manure mixing in 2:1 proportion, watering to the depth of 1" three times, weeding after every watering before plantation of the grass, leveling, rolling after proper compaction, planting of good quality lawn suckers by dibbling method in staggered fashion at specified intervals including transport & unloading. Watering and proper mowing etc. maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. Planting Jumping / Korian / Zoycia grass at 25mm c/c MCGM Garden SOR/ I.N. - GW-2-2-a / Pg - 16

Planting Lawn on Soft/Hard surface: Providing and filling Red Hill Earth & Cow Dung Manure mixing in 2:1 proportion, watering to the depth of 1" three times, weeding after every watering before plantation of the grass, leveling, rolling after proper compaction, planting of good quality lawn suckers by dibbling method in staggered fashion at specified intervals including transport & unloading. Watering and proper mowing etc. maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. Planting Jumping / Korian / Zoycia grass at 25mm c/c MCGM Garden SOR/ I.N. - GW-2-1-a / Pg - 15

Planting Shrubbery on Soft/Hard surface: Filling Red Hill Earth & Cow Dung Manure in the excavated area mixing in 2:1 proportion, watering, weeding after every watering before planting the shrub, leveling, providing and planting well grown, healthy, bushy shrubs including transport and unloading as per specified variety and sizes, planting at desired location and specified distances, maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. MCGM Garden SOR/ I.N. - GW-2-5 / Pg - 16

Gardenia Jasminoides - Aanat MCGM Garden SOR/ I.N. - GW-5-69 / Pg - 28

Lantena camera depresa MCGM Garden SOR/ I.N. - GW-5-94 / Pg - 28

Sedum S. MCGM Garden SOR/ I.N. - GW-5-149 / Pg - 29

Altanenthera - Red varigated MCGM Garden SOR/ I.N. - GW-5-140 / Pg - 29

Planting Shrubs on Soft/Hard surface (Individual): Filling Red Hill Earth & Cow Dung Manure and soil excaveted from pit in the excavated pits mixing in 2:1:1 proportion, watering, weeding after every watering before planting the shrub, leveling, providing and planting well grown, healthy, bushy shrubs including transport and unloading as per specified variety and sizes, planting at desired location and specified distances with appropriate staking, maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. MCGM Garden SOR/ I.N. - GW-2-2-a / Pg - 16

Ixora Chinensis - Prince of orange MCGM Garden SOR/ I.N. - GW-5-80 / Pg - 28

Nerum Oleander Album - White Kanher MCGM Garden SOR/ I.N. - GW-5-114 / Pg - 29

Bougainvillea Glabra - Purple Single flowers MCGM Garden SOR/ I.N. - GW-5-14 / Pg - 27

Plumbago Auriculata - Chitrak/ plumbago MCGM Garden SOR/ I.N. - GW-5-125 / Pg - 29

Caladium Hortulanum - caladium (Red/ White) MCGM Garden SOR/ I.N. - GW-5-169 / Pg - 30

Impatiens wallerania - sheady balsum perrinial MCGM Garden SOR/ I.N. - GW-5-185 / Pg - 30

Planting Hedges/ Edges/ Flower Beds on Soft/Hard surface: Filling Red Hill Earth & Cow Dung Manure in the excavated area mixing in 2:1 proportion, watering, weeding after every watering before planting the shrub, leveling, providing and planting well grown, healthy, bushy shrubs including transport and unloading as per specified variety and sizes, planting at desired location and specified distances, maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. MCGM Garden SOR/ I.N. - GW 2-4-a / Pg - 16

Baxus microphylla MCGM Garden SOR/ I.N. - GW-5-13 / Pg - 27

Planting Trees on Soft/Hard surface (Individual): Filling of Red Hill Earth, Cow Dung Manure & good earth from excaveted pit in the excavated pits mixing in 2:1:1 proportion, watering & providing well grown trees with minimum average girth of 2" and minimum height of 10' above finished level after plantation of specified variety , at desired location & at specified distances. Achieving finished grade level. Planting the tree with appropriate anchoring, leveling the top soil surface as specified after plantation, staking to balance the tree. Including transport to the site & planting , preparation of tree basin, watering & maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. MCGM Garden SOR/ I.N. - GW 2-5-a / Pg - 17

Foxtail Palm MCGM Garden SOR/ I.N. - GW-5-322 / Pg - 32

Plumeria Rubra MCGM Garden SOR/ I.N. - GW-5-203 / Pg - 30

Transplanting of Trees: Planting the tree in the pit filled with good soil, pressed down layer by layer, insecticide to be sprayed before planting, broken limbs tobe removed. tree to be supported by three strong stakes driven into the ground metre away from the stem, transport to the site & planting , preparation of tree basin, watering & maintaining for 1 month after completion of plantation and replacement of casualties till 1 month. MCGM Garden SOR/ I.N. - GW 2-5-c / Pg - 17

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern. As directed by Engineer in charge SSR 22-23 / Item No. - 48.06 / Pg 297

Providing and applying “high strength, non shrink free flow grout material” i. e. micro concrete (like shrink comp or equivalent) having compressive strength as 400 Kilogram/sq.cm. including finishing the surface and curing for 07 days. Etc complete. The usage of this non shrink concrete with zero slump is to allow to occupy every free space leaving no voids, thereby producing dense concrete with proper bonding with concrete (The quoted rates to be inclusive of all materials, labours, tools & tackles, transportation, taxes etc complete) to be applied for foundation and strengthening of pier etc and as per the direction of Site-In-Charge. (The product like Ultratech/Rendroc (RGL) of FOSROC or its equivalent)lete. SSR 22-23 / Item No.51.146/ Pg 380

NON SSR ITEMS

Providing & laying in position Low density polyethylene sheets (LDPE sheets) impermeable membrane of specified 150 micron of approved make & quality with necessary pressure adhesive tapes or with serrated joints made by an electric iron rod complete directed & instructed by Engineer/ Owner. (Minimum lap of sheets shall be 300 mm unless noted otherwise).

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.

75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

Providing and fixing half height partition with specfications as above item and top half with 12mm toughen glass, with all necessary fixures, as per design approved by Engineer in charge

Providing and fixing Modular Ceiling Systems with Mineral Fiber Board Tegular Edge Ceiling Tiles as per following specifications. Rate to include all fastening accessories with approved finishes. Ceiling tiles shall be approved make Micro look Edge tiles, of size 600mm x 600mm, of approved shade and colour. Tile shall render a NRC level of 0.5-0.6. Suspension system shall be manufacturer specific double rotary stitched (Trulok or equivalent) Silhouette reveal profile grid system with 15mm wide flanges incorporating 3 or 6mm central reveal of all white colour. Silhouette main runners and cross tees to have mitred ends and (Birds' mouth or equivalent) profiled notches to provide cruciform junctions.

Installation to comprise of main runners spaced at 1200mm centers securely fixed to the structural soffit by approved hangers at 1200mm maximum centers and not more than 150mm from spliced joints. The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centers to form 1200mm x 600mm modules. Cut cross tees longer than 600mm require independent support. 600mm x 600mm modules to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees. 1200mm cross tees to have central (Birds' mouth or equivalent) notches to facilitate flush fitting of 600mm cross tees. Perimeter trim to be (Trulok or equivalent) manufacturer specific sized wall angle of approved colour, secured to walls at 450mm maximum centers.

Providing and fixing 15 mm thick eco-friendly densified edge calcium silicate false ceiling of approved texture of size 595mm x 595mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanising at @12 gm/sq.m including both sides) consisting of main T runner suitably spaced at joints to get required length and size 24X38mm. made from 0.33mm thick(minimum ) sheet, spaced 1200mm center to center and cross T of size 24X28mm made of 0.33mm thick(minimum ) sheet to be interlocked at the middle of the 1200x600 mm panel to form the grid of size 600x600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size 24x24x3000 made of 0.4 mm thick (minimum) sheet with the help of all plugs at 450mm and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture (spintone/cosmos/hexa) in the grid, including light fittings , fixtures , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling using 12.5mm dia. And 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanized steel levels clips of size 85x30x0.8mm, spaced at 1200mm center to center along main T bottom exposed with 24mm of all T-sections shall be prepainted with polyester baked paint, for all heights, as per specifications, drawings etc. complete.(currently this item should be used only for VIP cabins) SSR 22-23 / Item No.38.39 / Pg 226

Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 Kilogram/m suspended on 6 mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete. SSR 22-23 / Item No.38.52 / Pg 231

Providing and fixing trap door in the Gypsum board / POP ceiling system for elecrical and mechanical utilities with 18mm thk. plywood shutter and 12mm thk. teak wood lipping all around including wooden / G.I. frame with supports, fixtures, fastenings etc. complete as directed MCGM-USOR-2023 / Item No.R3-CS-WW-23/ Pg No.122

Providing &Fixing frosted film manufactured by 3 M approved equivalent on glass partition wherever required as per the instruction of Architect. MCGM-USOR-2023 / Item No.R3-CS-RM-137/ Pg No.122

Providing and fixing 6 mm thick water proof grade Plywood 600 X 600 mm for support of lights, speaker, fire fighting fixtures etc. in ceiling.

Roofing, Cladding and gutter work

Item includes work at all height, including crane hydra, Farana for hoisting lifting, scaffolding, manual erecting etc. Welding and HST bolts. Material to be used of TATA, Jindal, SAIL ESSAR no re rolled steel will be allowed. electrodes shall conform to IS 814. Make to be Advani, Essar only.

All steel members will be Including painting with Grit Blast with Epoxy paint total 150 DFT considered for 1 coat 50 micron Primer ( zinc phosphate primer ) + 2 coat epoxy paint 50 micron each ; Same will be applied at Factory as a Mono coat system or as per manufacturer specification. Touch-up paint to be provided on site. If touch-up is not aesthetically good contractor will have to paint the entire rafter. The building should look aesthetically good.

Providing, fabrication and fixing of steel work Main frame Members will be built up using 345 MPA steel and HST bolted conenction including M.S. angles channel, Pipes. box section, R.S. beams, flats, plates, rods, Inset plates, chequred plates, Staricases, cage ladder etc. as per details design and drawing at any height including all labor, material with hoisting in position, including providing and fixing with HST bolts and nuts as per design at all conenctions and also by welding where ever required. incuding scaffolding, applying paint as above etc. complete as directed by engineer in charge. Rate shoudl include welding and HST bolts conenction, HST bolts will not be paid extra.

Providing and fixing MS foundation bolt, grade of steel 8.8 of any diameter at any and all level including making treads and bends as per drawing and specification completed as directed by engineer in charge. in RCC column / pedestal / beam at any level including maintaining the accuracy towards line, level & position including making and using the template etc. complete as directed by Engineer In Charge. (Rate shall include washer & nuts for which no weight shall be done ) (Contractor will take due care for its threads and rusting by applying grease and cotton waste.

Supplying & fixing and fabricating cold rolled formed "Z"section or C sections for purlins & side runners manufactured using raw material section conforming to ASTM-A653 having a minimum yield strength of 345 N/mm². The glazed coil shall be hot dip galvanized & it shall have a minimum coating of 120GSM as per IS: 277 including cutting section to exact length, punching as per drawing as attched. (Quoted rate shall be inclusive of loading, unloading & transportation). Size shall be as per drawing and approved by Engineer in charge. (Wastages and overlap will not be paid separately and quoted rates deemed to be included the same). (Make - Tata / JSW / SAIL / ESSAR)

Roofing, Cladding and gutter work

Note:- All roofing & related work would carry 10 years guarantee for water tightness. The contractor shall furnish guarantee bond on Rs. 100 stamp paper in the specified proforma for the entire contractor provided roofing & related works in bone dry condition for 10 years. During the guarantee period the contractor shall attend all leakages, defects etc. if noticed, free of cost, starting the work of checking up and rectification within a week's time from the date of intimation about such leakages/defects. On completion of the work & on confirmation from engineer in charge, contractor need to carry out water test at the pressure instructed by engineer in charge & submit the water test report as a confirmation for completion of work. All arrangements for water test to be done by the contractor. Only on submission of the water test report the will be considered as complete, subjected to the satisfaction of engineer in charge.

Note:- All below items includes all the required machineries & equipments such as Hydra, crane, Cheery Picker, etc & scaffolding at all heights & all labors including the required & essential PPE & safety arrangements.

Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center- to-center. The end rib shall be designed for anti-capillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/ One Square Metre) SSR 22-23 / Item No. 38.34 / Pg 224

Providing & Installing Side cladding Providing color coated Galvalume / Zinc Aluminium sheet 0.5 mm thick profile sheet. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material is manufactured out of nominal 0.50 mm Total Coated Thickness (TCT), Hi-Tensile steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% Aluminum, 45% Zinc) as per AS 1397 . The paint will have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved color shade by concern authority. The sheet will have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. Approved make - Tata Blue scope, JSW colouron plus.

External Cladding / Internal Liner panel

Providing and fixing 8 mm thick double bubble insulation The Reflective Insulation material should consist both side pure Aluminium Foil with two layers of closed cell Fire Retardant Bubbles in between, Nominal thickness 8 mm, Low Emissivity - 0.032 (ASTM1371), Reflectivity - 97%, Weight - 425 GSM, R value - 1.27 m2∙K/W, Fire Class A (ASTM E84) Surface Burning Characteristics - Flame Spread Index(0) & Smoke Developed Index (30) ,Tensile strength at peak (ASTM D 882) – Machine Direction 4347gf/cm, Transverse Direction 3822 gf/cm, All technical values should be supported by third party certificates. Comply with UL94 - HF1 rating. Incl. necessary scaffolding etc. complete. Approved make - Aerolam / Polynum

Providing and fixing Insulation Bonded Fiber Glass Wool Insulation having density of 24 kg/cu.m, 75mm thickness suitably factory laminated with high-strength polypropylene based WMP-50 facing. • The polypropylene facing should have extensions or tabs of 50 mm on one or both of the long edges of the insulation blanket. • Thermal resistance of the Insulation should be R- 2.25 sq.m.K/W . • Insulation material shall be non-combustible, non-toxic, low smoke emitting, chemically inert, free from impurities like Sulphur, chloride and metal shots. Material made of steel plants slag shall not be acceptable. For the purlin spacing, nylon mesh is to be used between the purlin & Roof Sheet to hold the insulation blanket. approved Make Owens Corning / UP Twiga Fiberglass

Providing and fixing Flashing Galvalume color coated profiled sheets made out of 0.5 mm TCT (including paint thickness) made of metallic Al-Zn alloy (55% Aluminum, 43.5% Zinc, 1.5% Si ) conforming to ASTM A792M or AS 1397 - AZ150 minimum (150 g/m2 ) coating mass, (minimum yield strength 345 MPa). The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. as per drawing and as directed by engineer in charge. Complete.

Up to 300mm Girth

301 to 600mm Girth

601 to 900mm Girth

Providing & Fixing GI gutter Galvalume color coated profiled sheets made out of 2.5 mm TCT (including paint thickness) made of metallic Al-Zn alloy (55% Aluminum, 43.5% Zinc, 1.5% Si ) conforming to ASTM A792M or AS 1397 - AZ150 minimum (150 g/m2 ) coating mass, (minimum yield strength 345 MPa). all complete as per drawing, as directed and specified by engineer-in charge.

Providing and fixing single skin trapezoidal profiled sheeting 930 - 1020mm cover width 28-32 mm crests depth at 186-250 c/c ( above 195 mm c/c crest distance there will be minimum 2 ribs at the centre for stiffening). The feed material shall be manufactured from AZ 150 (min. 150 gms/sq.mt total on both sides) Zincalume / Galvalume sheets of minimum yield strength of 550 MPa, 0.45 mm BMT, ( 0.5 mm TCT excluding paint coating thickness), metallic hot dip coated with Al- Zn alloy (55% Aluminium, 43.5% Zinc, 1.5% Si ) as per AS 1397 / IS15961 & painted with Super Durable Polyester Colorbond steel XRW or equivalent quality paint system of apporved color, suitable for exterior application conforming to AS/NZS 2728:2007 type-4 / IS15965:class3 of approved make. The sheet shall have a total coating thickness of 35 microns, super durable polyester paint system of 20 microns on exposed surface and 5 micron reverse polyester coat on back surface over 5 micron primer coat on both surfaces. The paint system shall have stable inorganic pigments for color durability.The product will be fastened using no.12-14x55 mm (or as per design requirement ), mechanically coated with 25 micron Zn-Sn alloy or hot dipped zinc coated with min 40 micron hex self-drilling fasteners with EPDM washer of approved make confirms to AS3566:2002 class 3. MCGM-USOR-2023 / Item No.R3-CS-RW-09/ Pg No.99

Colour Coated Galvalume/zincalume sheets for cladding

Colour Coated Galvalume/zincalume Flashings and Cappings 600mm wide

Supply & Installing 2 mm thick clear embossed Polycarbonate Sheet Polycarbonate profile to match the standing seam profile with side lapsto be fixed/clamped with sheets of 0.55 mm [TCT] . Which can be further fixed/seamed with metal roof sheets. Product required is clear embossed with both side UV stabilizer, having at least 60 to 80% transparency, confirming to relevant IS Code [IS14443:1997 or latest] including cutting to shape and size as required including necessary sealants, silicon sealant/butyl sealants for transverse laps. Including all material, tools & tackles, labour etc. required for completing the work in all respect as per direction of engineer in-charge.

Providing and fixing UV resistant selffit UPVC pipes of approved make for Rainwater downtakes confirming to IS 13592:1992 Type A suitablefor 4kg/sqcm pressure for following pipe diameters including rain water receiving recess with pvc plug bend necessary fittings such as offsets shoes, fixing the pipes on wall with clips filling the joints with solvent/cement and necessary scafolding etc. complete as directed by Engineer In Charge. MCGM-USOR-2023 / Item No.R3-CS-RW-16/ Pg No.100

75 mm dia

100mm dia

150mm dia

200mm dia

Dual Desk-Bench Sets

Providing, supplying, and installing dual desk-bench sets designed for two students, suitable for classroom. The frame shall be fabricated from mild steel (MS) tubular sections, finished with a durable powder coating to resist corrosion and ensure longevity in high-usage environments. The desktop shall be made of 18 mm thick pre-laminated particle board, conforming to IS 12823 standards, with PVC edge banding to ensure smooth edges and enhanced durability. The surface shall be scratch- and stain-resistant, making it suitable for regular classroom use. The bench seat and backrest shall have a laminated finish and be ergonomically designed as per IS 4837, ensuring proper posture and comfort during extended classroom sessions. The design shall incorporate anti-skid rubber foot caps at the base of the frame to protect flooring and provide slip resistance. The desk-bench unit shall be of fixed, welded construction, with all components securely assembled at the factory and delivered ready to install at the site.Considering the size @ 1350L x 350D x750 Ht mm

Teacher’s Table

Providing, supplying, and installing a Teacher’s Table of overall size 1200 mm (L) × 600 mm (W) × 750 mm (H), suitable for classrooms and staff rooms in educational institutions. The table shall have a sturdy MS (Mild Steel) frame, fabricated from square or rectangular tubular sections and finished with a durable powder coating to prevent corrosion and enhance aesthetic appeal. The tabletop shall be constructed using a high-quality laminated board, ensuring resistance to scratches and stains. The edges of the tabletop shall be sealed with PVC edge banding for safety and durability. A modesty panel of appropriate material shall be provided along the front for visual screening and structural stability.

Teacher’s Chair

Providing, supplying, and installing ergonomic revolving chairs suitable for use by teachers or staff in classrooms, offices, and institutional environments. The chair shall feature a mild steel (MS) frame structure with a five-star base, designed for durability and stability. The chair shall be equipped with a cushioned seat and backrest , ergonomically contoured to support long-duration sitting. The upholstery shall be made of fabric or leatherette, as specified, offering comfort and ease of maintenance. The chair shall include height adjustment, a 360-degree revolving mechanism, and smooth-rolling castor wheels for mobility. All components must be designed for regular institutional use, with smooth operation and long-term reliability.

Smart Classrooms

Interactive Board Wall Mount Provision

Providing, supplying, and installing a heavy-duty adjustable wall mount bracket suitable for securely mounting a 75-inch interactive flat panel display. The mount shall be fabricated from high-strength steel, with a durable powder-coated finish, and include integrated cable management channels to ensure a neat and clutter-free installation. The wall mount shall feature tilt and horizontal adjustment options to accommodate ergonomic viewing angles and installation flexibility. It shall be supplied complete with anchor fasteners, wall plugs, and all necessary hardware for safe and secure fixing to solid concrete or brick walls. The system must be load-tested and compatible with VESA standard mounting patterns, ensuring universal fit for major brands of 75" panels.

Modular Student Tables

Providing, supplying, and installing modular student tables designed for flexible classroom or laboratory use. The table shall be constructed with a mild steel (MS) frame, fabricated from high-quality tubular sections, and finished with a durable powder coating to ensure resistance to corrosion and wear. The tabletop shall be made of 18 mm thick laminated board, featuring a scratch- and stain-resistant surface, and finished with PVC edge banding for durability and safety. The table shall be provided with grommet holes for efficient cable routing, allowing integration with IT equipment or smart classroom tools. These modular tables shall be suitable for group arrangements and reconfiguration as per classroom needs. All components must be factory finished and delivered ready for installation at the site. Considering the size @1000Lx 750Dx 750Dmm

Modular Student Chairs

Providing, supplying, and installing modular student chairs designed for comfort, durability, and flexibility in classroom and training environments. The chairs shall feature an ergonomic design, with a moulded polypropylene shell seat or cushioned seat and back, as specified.The base structure shall be made from mild steel (MS) with powder coating or reinforced nylon, ensuring stability, corrosion resistance, and long-term performance. The chairs shall be lightweight yet sturdy, stackable or mobile (if specified), and suitable for use with modular desks. The design shall promote good posture during extended periods of sitting, and all edges and finishes shall be smooth and student-safe.

Modular Steel Workbenches

Providing, supplying, and installing modular steel workbenches with an all-steel welded frame, designed for workshop and laboratory applications. The frame shall be fabricated from high-strength steel sections and finished with a durable powder coating to resist corrosion and wear. The workbench shall have a length ranging from 1500 mm to 2100 mm, with a worktop made of either seasoned hardwood or laminated top, having a thickness of 25 mm to 40 mm. Each workbench shall include adjustable leveling feet for floor stability and a provision for vice mounting to support technical or mechanical operations. The bench shall be delivered in fully assembled condition or as a knock-down kit with easy on-site assembly.

Storage Racks (Heavy Duty)

Providing, supplying, and installing heavy-duty storage racks constructed from powder-coated steel sections, suitable for workshops, labs, and storerooms. Each rack shall consist of adjustable shelves, supported on vertical uprights with perforations at regular intervals to allow shelf height adjustments. Each shelf shall have a minimum load-bearing capacity of 200 kg, uniformly distributed. The surface finish shall be corrosion-resistant powder coating in grey or blue color as approved. The racks shall be provided with leveling base plates and all required accessories for secure installation. Considering the size @ 1000Lx500 Dx1800 ht mm

Tool Cabinets (Lockable)

Providing, supplying, and installing heavy-duty lockable tool cabinets fabricated from CRCA steel sheets (0.8 mm to 1.0 mm thick), powder-coated for corrosion resistance. Each cabinet shall include 5 to 7 drawers, fitted with smooth sliding mechanisms, and foam-lined interiors for tool protection. The unit shall be equipped with a central locking system, sturdy handles, and leveling supports at the base. Suitable for industrial training, workshops, or maintenance rooms.Considering the size @ 1140Lx 457D x 1830 mm. Ht.

Staff Room

Work Desks

Providing, supplying, and installing work desks measuring 1200 mm (length) x 600 mm (width) x 750 mm (height). The desks shall have a robust mild steel (MS) frame with powder-coated finish for corrosion resistance and durability. The desktop shall be made of high-quality laminated board for scratch and stain resistance. Each desk shall be equipped with a lockable drawer unit to provide secure storage for office supplies and documents. The design shall ensure stability, functionality, and ergonomic comfort for office use.

Storage Unit / Cupboard

Providing, supplying, and installing storage units or cupboards fabricated from 1.0 mm thick CRCA steel sheets, finished with a durable powder-coated paint to prevent corrosion and wear. The storage unit shall include adjustable shelves to allow flexible storage configurations and lockable doors for secure containment of materials. The cupboard shall be designed to provide ample storage space suitable for office or institutional use, with sturdy construction ensuring longevity and ease of maintenance. Considering the Medium Height Steel Storage @ 750Lx450Dx1200HT

Office Chairs

Providing, supplying, and installing ergonomic office chairs featuring a revolving mechanism and cushioned seat and backrest upholstered in durable fabric or leatherette. The chairs shall have height adjustment via gas lift, an MS or nylon base for stability, and integral armrests to enhance user comfort. The chair design must ensure good posture support and mobility, suitable for extended office use.

Smart Classroom Audio-Visual Setup

Projector

Providing, supplying, and installing a high-quality DLP/LCD projector with a minimum brightness of 3500 ANSI lumens and resolution of XGA/WXGA for clear and bright image projection suitable for classrooms, conference rooms, and presentation areas. The projector shall have a lamp life of at least 15,000 hours in Eco mode ensuring long-term durability and low maintenance. Connectivity options shall include HDMI, USB, VGA ports, with wireless connectivity as an optional feature for ease of use. The supply shall include a ceiling/wall mounting kit with all necessary hardware for secure installation.

Smart Board / Interactive Flat Panel

Providing, supplying, and installing an interactive flat panel with a minimum diagonal size of 75 inches. The panel shall support multi-touch functionality with at least 20 simultaneous touch points, enabling collaborative and interactive learning. It should come with an integrated Android operating system and PC interface compatibility to support versatile content display and application use. The supply shall include a heavy-duty wall-mount bracket, cable management system, and connectivity options compatible with projectors and laptops to ensure seamless integration in classroom or conference environments.

Speaker System

Providing, supplying, and installing a 2.1 or 4-speaker wall-mounted audio system with a power output of 30 to 50 Watts RMS per channel to ensure clear and adequate sound coverage for classrooms, auditoriums, or conference rooms. The system shall include an integrated amplifier with remote control for easy operation. All necessary mounting hardware, wiring, and accessories for a complete functional installation shall be provided.

Signages

Siganages for Male, Female, and Handicap icons on toilet doors, crafted from 3mm thick brass with a brushed finish. The icons will be directly mounted on the surface for a clean, minimalistic look. Designed for durability, the brass finish provides resistance to wear and corrosion. Icons should be clearly visible, with secure mounting to ensure longevity and ease of maintenance.

Directional / Way finding Signage- Design, supply, fabrication and fixing acrylic multilingual Braille (raised dots) directional signboards of size 6" x 9" designed as per accessibility standards and having 4mm thick acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate and having a non glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufacturers specifications on the wall at the approved location and at a height of 1200mm from FFL and as per the directions by the engineer in charge.

Department / Lab / Staff Room Signage- Acrylic or aluminium composite; size approx. 250×200 mm; name and department printed or engraved; colour and font consistent with overall signage scheme

Design, supply, fabrication and fixing acrylic multilingual Braille (raised dots) directional signboards of size 6" x 9" designed as per accessibility standards and having 4mm thick acrylic base plate with Upper Case San Serif words made of white acrylic non glare cut out letters of height 15mm raised not less than 0.8mm above base plate and the equivalent word written in Hindi with Devnagri non glare acrylic letters of height 15mm raised not less than 0.8mm above base plate and having a non glare acrylic cut arrow pointing in the required direction. Each signboard to be fixed as per manufacturers specifications on the wall at the approved location and at a height of 1200mm from FFL and as per the directions by the engineer in charge. State SSR 22-23/I.N. 51.67/ Pg. 358

Supply and installation of fire safety signages 300mm x 300mm made of high-quality radium (photoluminescent) material including: - Fire Exit Signs - Fire Extinguisher Location Signs - Directional Fire Exit Arrow Signs - Assembly Point Signs - Fire Alarm Point Signs - First Aid Box Signs All signage to be bilingual (English + local language), compliant with safety regulations, and securely installed at designated locations throughout the school premises. Rate includes materials, transportation, installation, complete. as per the directions by the engineer in charge.

Acrylic Sign Board for Class Room/Building/Lab Supply, fabrication, and installation of Acrylic Sign Board for the Class Room/Building/Lab, size approximately 1200mm x 600mm, made of high-quality 5mm thick acrylic sheet with UV-resistant finish. Includes laser-cut lettering and logo, double-sided printing (if applicable), and mounting on the wall with suitable fixtures and all necessary hardware. The signage shall be weather-resistant, fade-proof, and comply with aesthetic and safety standards. Rate includes material, fabrication, transportation, installation, and secure fixing on the building façade. Final size and design to be approved by the PMC before fabrication, complete. as per the directions by the engineer in charge.

HVAC WORK

Note: Prices shall be based on supply, installation, testing & commissioning at site including all taxes, duties, transportation & insurance etc.

DX BOQ

Hi-Wall Split unit

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit following capacity having ISEERISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall complete with refrigerant R-32/ R-410 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level ≤ 40 dBdBA,outdoor shall be powder coated weather proof cabinet complete.

Note: All civil work for installation of indoor & outdoor unit shall be done by HVAC contractor.

Refrigerant Piping

Supply, installation, testing & commissioning of refrigerant grade copper tubing in ceiling / wall with support interconnecting outdoor and indoor units duly insulated with 9mm thick elastomeric nitrile rubber tubing to prevent any heat loss, suitable sizes including chase cutting making good & clamping etc.

Power and control wiring

Supply, installation, testing & commissioning of power cables /control cables MS counduiting duly complete with all fittings as per specification of suitable sizes from indoor units to outdoor units for the different capacities of split type air-conditioning .The wiring/cabling shall be as per the manufacturer's recommendations. All civil work like chase cutting of wall, floor and repair etc. shall be done by HVAC contractor.

2 C x 1.5 sq. mm. - Communication cable

3 C x 2.5 sq. mm. - Power cable

Condensate Drain piping

Providing and fixing and in position the following multi-layer composite pipes for condensate drain as per specification ,cut to required length and installed with all joints , including the necessary fittings. (For all the indoor units upto the floor trap as shown in the drawings)

25 mm dia

32mm dia

VRF- Outdoor Condensing Units

Modular type fully Imported outdoor units equipped with highly efficient DC twin rotary / inverter scroll compressors, pre-coated heat exchanger/condensing coil, Fins of Multi Row with “Anti Corrosive” treatment, low noise condenser fan, auto check function for connection error, auto address setting, with multiple outdoor units, including providing initial gas charging, System Should Run at nominal working voltage, suitable electrical & refrigerant line interconnections complete including, cartage etc. as required. Each Outdoor units with High Pressure switch, Fan driver overload protector, Over current relay, Inverter Overload Protector & Fusible Plug. Refrigerant shall be R 410 A ready for use with single point electrical supply & refrigerant suction / liquid line tapping, all compressors shall be of inverter type only for better efficiency. The COP should be minimum 5.40 at 50% part load under normal operating conditions.outdoor shall be powder coated weather proof cabinet complete.

12 HP Outdoor unit

14 HP Outdoor unit

16 HP Outdoor unit

Supply, installation, testing and commissioning of VRF based Cassette type unit complete with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil suitable for HFC refrigerant, washable air filter,insulated drain tray, in built drain pump, expansion device,cordeless remote control with necessary controls and electrical terminal to receive power supply, etc., as per the approved drawings and specifications. The indoor unit shall also have an electronic control console. The unit shall be suitable for wall mounting and provided with suitable mounting brackets.

Price quoted shall also include the following:

Any additional refrigerant and oil charge required.

Elecrical power point will be provided 5ft away from unit.

Contractor to ensure that MCB/power point provided is of correct rating.

VRV Hi Wall Unit

Supply, installation, testing and commissioning of VRF based Hi wall type unit complete with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil suitable for HFC refrigerant, washable air filter,insulated drain tray, in built drain pump, expansion device,cordeless remote control with necessary controls and electrical terminal to receive power supply, etc., as per the approved drawings and specifications. The indoor unit shall also have an electronic control console. The unit shall be suitable for wall mounting and provided with suitable mounting brackets.

Refnet joint

Providing, fixing, testing and commissioning of Variable refrigerant flow distribution REFNUTS / T Joints (in pair) in the suction & Liquid lines for various sizes of copper refrigerant piping including insulation etc. as required.

Refrigerant Pipe

Supply, installation, testing and commissioning of copper pipe suitable for refrigeration system having adequate thickness, between indoor and outdoor unit, duly insulated with class 0 closed cell nitrile rubber insulation of adequate thickness complete with Tees, Bends, couplings, refnet joints, header joints, supports, trays etc., as per approved drawings & specifications.

Control cabling for ODU to IDU - Shielded Communication/Control Cabling 2c x 1.5 Sq.mm with 20 mm Dia PVC Conduit as required (Between Indoor & Outdoor Units and for remote control units)

Supply and Installation of "L" Type MS stand for Outdoor Units

1. Point wiring shall include all necessary "PVC Cassing caping", with all fittings, accessories, couplings, collars etc. 2. Junction / pull / inspection boxes, wires, supports, bushings lamp holders, ceiling rose, flexible conduit, fan hooks wherever required shall be part of point wiring 3. Modular switch, switch box, cover plate, Fan electronic regulator & terminations using tinned copper lugs of crimping type shall be part of point wiring 4. All necessary chiselling and filling works required for concealed wiring shall be part of point wiring. 5. Numbering for raw and emergency light fixtures, switch boards, power points including earth pits etc. complete. (Marking of light fixtures, Raw points shall be provided on laminated printed paper.)

All Primary /Secondary point lighting fixture wiring shall be carried out using 3 X 1.5sqmm copper stranded & conductor 660/1100V grade FRLS insulated wire in desired conduit. PVC Cassing Capping /conduit shall be used for indoor wiring and MS conduit shall be used for outdoor areas (Canopy etc). Individual junction/inspection boxes shall be provided for each lighting fitting for the purpose of looping from fitting to fitting.

From switch board/DB to first light fitting will be termed as primary point and First fitting to subsequent fitting on the same circuit shall be as termed secondary point.

Providing point wiring for light/bell/ceiling fan/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification Standard length shall be considered upto 8 meter-Short Point

Providing point wiring for light/bell/ceiling fan/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification Standard length shall be considered from 9 meter upto 15 meter-Medium Point

Providing point wiring for light/bell/ceiling fan/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification Standard length shall be considered from16 upto 20 meter-Long Point

Providing Secondary point wiring for additional light, open type in PVC trunking (cassing capping) with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories complete as per specification.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20mm with accessories on wall/ceiling as per specification.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25mm with accessories on wall/ceiling as per specification.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 mm with accessories on wall/ceiling as per specification.

Supply, Installation, Testing & Commissioning of 20mm dia. corrugated flexible polypropylene conduit

Supply, Installation, Testing & Commissioning of 25 mm dia. corrugated flexible polypropylene conduit

Supplying and erecting modular type (two module) electronic step regulator for fan, on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module including modular type 6 A Switch & 3 pin 6A multi socket with safety shutter.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module including modular type 16 A Switch & modular type 3 pin 6/16A multi socket with safety shutter.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module including modular type 2 no's 6 A Switch & 2 no's 3 pin 6A multi socket with safety shutter.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module including modular type 2 no's 16 A Switch & 2 no's 3 pin 6/16A multi socket with safety shutter.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module including modular type T.V. socket single outlet

Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module including modular type telephone socket one gang with safety shutter

Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module including modular type computer Jack RJ 45 with safety shutter

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module including modular type 25A DP MCB

Supplying & erecting mains with 3x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification

Supplying & erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification

Supplying & erecting mains with 3x4sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 24 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background

Supplying and erecting modular type switch 6A/10A on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16A on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6/16A multi socket with safety shutter on provided plate and box with wiring connections complete

Supply, Installation, testing & commissioning of 63 A 4 pole three phase 5 pin industrial socket with 63 A MCB & plug including terminations with double compression gland enclosed in enclosure made out of 1.2 mm thick sheet steel enclosure, pre-treated and painted with two coats of primer and two coats of epoxy paint.

Supply, Installation, testing & commissioning of 40 A 4 pole three phase 5 pin industrial socket with 40 A MCB & plug including terminations with double compression gland enclosed in enclosure made out of 1.2 mm thick sheet steel enclosure, pre-treated and painted with two coats of primer and two coats of epoxy paint.

Supply, Installation, testing & commissioning of 20 A 4 pole three phase 5 pin industrial socket with 20 A MCB & plug including terminations with double compression gland enclosed in enclosure made out of 1.2 mm thick sheet steel enclosure, pre-treated and painted with two coats of primer and two coats of epoxy paint.

Supply, Installation, testing & commissioning of 20 A single pole single phase 3 pin industrial socket with 20 A MCB & plug including terminations with double compression gland enclosed in enclosure made out of 1.2 mm thick sheet steel enclosure, pre-treated and painted with two coats of primer and two coats of epoxy paint.

Supply, Installation, testing & commissioning of LED 22 W batten light fitting (4 feet) with aluminium extrusion hosing, heat sink, integrated HF electronic driver complete including suitable suspension/Surface mounting accessories

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular 9 to 12W down lighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT up to 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.

Supplying Installtion Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control/compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 12 ways /phase (36 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 12 ways /36 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness including 32/40 Amps DP MCB complete erected on angle iron/GI frame.

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness including 63 Amps TP MCB complete erected on angle iron/GI frame.

Supplying and installing LSZH sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in conduit/casing-n-capping as per specification

Supplying and fixing 1 m UTP patch cord of Cat 6 type in position

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position

Supplying and installing cat-6 armoured cable with ECCS tape suitable for networking

Supplying, erecting, testing and commissioning of 3kVA capacity online pure sine wave with backup time of 01 hrs. PWM & IGBT based UPS with 0.8 to unity output pf, single phase input & 1 phase output complete with all protections.

Supplying and erecting 12V/100Ah tubular battery with battery terminal wire, duly charged with 36 months warranty complete.

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying, installing and testing 15m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification

Supplying, fixing, and configuring 24 ports, PoE switch compliant with IEEE 802.3 standards with min. 193W PoE capacity with 4GE SFP uplink in provided rack as per specification

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable, 1100 V 3½ core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification

Supply & fixing of 4 Nos Fire Buckets with stand.

Supply of Hand Gloves - 11KV grade complete all as specified and directed by Engineer-in charge.

Supply of fibre discharge rod suitable for 11Kv supply. The discharge Rod should have die cast copper clamp with 15 mtrs length copper cable.

Supply of First Aid Box.

Supply and Fixing of Laminated First Aid Charts in Hindi, English & Local language.

Supplying, installing and testing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.I. cover complete with all accessories of G.I. materials & recording the results as per specification

Supplying, installing and testing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all accessories of copper materials & recording the results as per specification

Supplying and erecting copper strip of required size used for earthing in ground/ on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints as per specification

Supplying and erecting GI strip of required size used for earthing in ground on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints as per specification