Provn of black top road from bldg No T-206 Receipt Inspection Section to Veh Service Point of certain unit a special repair to road near OTM Accn of certain unit at Mil Stn Bikaner and special repair/renovation of road of staff qtrs in KV-2 at Bikane

Amount

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated soil/material to a distance exc 200 m and not exc 250 m and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed.

Rolling and consolidating formation surfaces in cutting/filling with 8 to 12 tonne power road roller to required level, gradient and camber including filling in depressions which occur during the process of rolling, watering as necessary, complete all as specified and as directed.

M&L for Soling (or sub base) 150mm thick (spread thickness) in one layer with broken boulders or quarried stone (Granite, Trap, Basalt), interstices filled of grading 1 (90 to 45 mm size), surface formed, rolled and consolidated to required gradient and camber with 8 to 12 tonne power road roller complete all as specified and as directed.

M&L for 150 mm thick (Compacted thickness) WBM, in two layers (75 mm thick each layer) with coarse aggregates of granite, trap or basalt stone of grading 2 (63 mm to 40 mm size) or of grading 3 (50 to 20 mm size), blinded with screening of hard stone of grading ‘A’, spread, watered and rolled with 8 to 12 tonne power roller, hollows made up to form true surface and consolidated to required gradient and camber etc, complete all as specified and as directed

Material & Labour for preparing newly laid un-surfaced WBM surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surfaces with air compressor through air jet to remove all loose dirt etc and applying evenly a tack coat of paving bitumen primer of grade VG-10 at the rate of 10 Kg per 10 Sqm of road surface by sprayer operated on hot pressure mechanism, providing, laying, spreading 40mm thick (consolidated thickness) of premix Semi Dense Asphaltic Concrete (SDAC) with crushed and graded coarse aggregates as per design based on Job mix formula with 5.5% bitumen binder content (bitumen of Grade VG-30) by weight of total mix including heating bitumen to the required temperature, mixing bituminous concrete in automatic and temperature controlled hot mixing plant, laying, spreading uniformly by means of Mechanical paver and rolling and consolidating to the required gradient and camber with 8 to 12 tonne power road roller and Vibromax roller to a uniform smooth surfaces complete all as specified and as directed. Notes : (i) Job mix formula shall be approved by CWE. (ii) Paving bitumen primer of Grade VG-10 for tack coat and bitumen of Grade VG-30 for semi dense asphaltic concrete shall be used and shall be procured by the contractor under his own arrangement and at his own cost. (iii) Cost of all the materials, T&P, labour etc. required for preparation of surfaces, applying tack coat, providing and laying semi dense asphaltic concrete including procurement of bitumen as specified here-in-before, stone aggregates & sand etc., rolling and all other elements required for entire completion of the job shall be deemed to be included in the unit rate quoted for this item. (iv) Computerised print out of data of bituminous concrete in automatic and temperature controlled hot mixing plant shall be provided to the GE by contractor.

M&L for preparing black top bituminous surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surfaces with air compressor through air jet to remove all loose dirt etc and applying evenly a tack coat of paving bitumen primer of grade VG-10 at the rate of 05 Kg per 10 Sqm of road surface by sprayer operated on hot pressure mechanism, providing, laying, spreading 30mm thick (consolidated thickness) of premix Semi Dense Asphaltic Concrete (SDAC) with crushed and graded coarse aggregates as per design based on Job mix formula with 5.5% bitumen binder content (bitumen of Grade VG-30) by weight of total mix including heating bitumen to the required temperature, mixing bituminous concrete in automatic and temperature controlled hot mixing plant, laying, spreading uniformly by means of Mechanical paver and rolling and consolidating to the required gradient and camber with 8 to 12 tonne power road roller and Vibromax roller to a uniform smooth surfaces complete all as specified and as directed. Notes : (i) Job mix formula shall be approved by CWE. (ii) Paving bitumen primer of Grade VG-10 for tack coat and bitumen of Grade VG-30 for semi dense asphaltic concrete shall be used and shall be procured by the contractor under his own arrangement and at his own cost. (iii) Cost of all the materials, T&P, labour etc. required for preparation of surfaces, applying tack coat, providing and laying semi dense asphaltic concrete including procurement of bitumen as specified here-in-before, stone aggregates & sand etc., rolling and all other elements required for entire completion of the job shall be deemed to be included in the unit rate quoted for this item. (iv) Computerised print out of data of bituminous concrete in automatic and temperature controlled hot mixing plant shall be provided to the GE by contractor.

M&L for repairs to pot holes, not exc 1 square metre each, including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, cutting around edges to at least 25 mm in depth, on existing road surfaces, and making good applying evenly a tack coat of paving bitumen primer of grade VG-10 at the rate of 05 Kg per 10 Sqm, putting in premix Semi Dense Asphaltic Concrete (SDAC) with crushed and graded coarse aggregates as per design based on Job mix formula with 5.5% bitumen binder content (bitumen of Grade VG-30) by weight of total mix, well rammed, including supply of SDAC, depth of pot holes not exc 30mm, complete all as specified and as directed. Notes : (i) Job mix formula of SDAC shall be approved by CWE. (ii) Paving bitumen primer of Grade VG-10 for tack coat and bitumen of Grade VG-30 for semi dense asphaltic concrete shall be used and shall be procured by the contractor under his own arrangement and at his own cost. (iii) Cost of all the materials, T&P, labour etc. required for preparation of surfaces, applying tack coat, providing and laying semi dense asphaltic concrete including procurement of bitumen as specified here-in-before, stone aggregates & sand etc., rolling and all other elements required for entire completion of the job shall be deemed to be included in the unit rate quoted for this item. (iv) Computerised print out of data of bituminous concrete in automatic and temperature controlled hot mixing plant shall be provided to the GE by contractor. (v) This item shall not be executed, measured and paid for repairs to pot holes existing on the portion of road surfaces which shall be carpeted under serial item No. 7.00 here-in-before and shall only be executed, measured and paid for repairs to pot holes existing on road surfaces which are not to be carpeted.

M&L for continuous Jodhpur stone slab edging, not less than 7.5 cm thick, 30 cm to 35 cm wide (for depth of edging) and 30 cm to 45 cm long, laid dry vertically, jointing and pointing in CM 1:4, each stone slab self faced on both the vertical sides, edges slightly true and square on top edge, hammer dressed for the full thickness so that the depression from a straight edge held against the surfaces shall not exceed 20 mm between two joints of slab including necessary excavation and embedding stone edging to depth required and tamping ground around stone edging and also including spreading surplus soil on berms complete all as specified and as directed. Notes :- (i) The stone slabs shall be laid abutting to each other in such a way that thickness of edging is equal to thickness of stone slabs and depth of edging is equal to width of stone slabs. (ii) The stone slabs shall be obtained from “Chitter quarry” at “Jodhpur”. (iii) In case edging is laid on both sides of a road, each side of road shall be measured and paid for separately.

M&L for preparing surface and filling Moorum / red bajri in road side berms or paving, laid in thickness not exc 15 cm, spread, levelled and rammed to required gradient and camber including watering complete all as specified and as directed.

M&L for Thermo plastic road marking 2.0 mm thick painting (lines, dashes, arrows, letters etc on new or previously treated road surfaces) with road safety spikeries glass beads including preparation of new or previously treated road surfaces and applying paint by using special applicator machine with heating arrangement complete all as specified and as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in foundations, filling, sub base and mass concrete complete all as specified and as directed.

M&L for 100mm thick PCC (1:2:4) type B2 using 40mm graded crushed stone aggregate as in flooring, leveling course, etc, laid in panels, surface finished fair and even, complete all as specified and as directed.

ENGINEER CORPORATION OF INDIA

M/S BUDHRAM BISHNOI

SHREE GURU NANAK CONSTRUCTION COMPANY

Ram Parkash Constructions Pvt. Ltd.